The thesis is aimed on a proposal from heating sources, heating systems and ventilation of family house. Designing of a house is provided by Keeo4design. This proposal contains a complex of two houses. The first one is used for residential purposes, the other is made up of mostly parking garages. The work focuses on heat loss calculation objects. Subsequently, on a proposal from heating sources, heating systems, ventilation systems and their regulation.

This thesis evaluates the connection of solar collectors with heat pump. The work demonstrates meaningful use of solar collector to increase cooling efficiency of the heat pump. Introduction The work introduces the reader to the issue and describes basic principles of the two main sources of energy used in the system - the heat pump and solar system. Next session is dedicated to analysis and evaluation of the data that was measured during system operation. A comparison of measured COP of the heat pump at two different modes of operation was used for the evaluation - with the help of the solar system and without using the solar system.

Sala Silvergruva AB är ett av många företag som just nu kämpar med höga energi-kostnader. Denna rapport undersöker vilka möjligheter det finns att skapa ett hållbart energisystem i Sala Silvergruva med avseende på ekonomi, miljö samt sociala aspekter.   Rapporten undersöker nio tekniker; vindkraft, vattenkraft, solfångare, solceller, pelletspannor, värmepumpar, effektivisering samt lagring av värme från växthus respektive fjärrvärme. Dessa analyseras var för sig med utgångspunkt i tio krav som speglar hållbarhetsaspekterna. I samband med analysen ges rekommendationer angående investering i respektive energilösning. Rapporten mynnar ut i en resultatskarta där det tydligt framgår vilka krav de olika teknikerna uppfyller. Den följande diskussionen leder fram till en slutsats som presenterar vilka åtgärder som bör vidtas i syfte att skapa ett uthålligt energisystem för Sala Silvergruva AB.   Pelletspannor och värmepumpar visar sig i nuläget vara de mest uthålliga tekniklösningarna. På grund av husens ålder och egenskaper bör även energieffektiviserande investeringar göras. Eventuella investeringar beräknas vara återbetalda inom 1-5 år.   Det finns finansiella incitament för det lokala energiföretaget Sala-Heby Energi AB att bygga ett fjärrvärmelager i gruvan. En sådan lösning visar sig skapa nytta för såväl Sala Silvergruva AB som regionen i helhet. Återbetalningstiden för Sala-Heby Energi blir mellan 4 till 12 år vid en investering, beroende på lagerstorlek. / Sala Silvergruva AB is one of many companies currently struggling with high energy prices. This thesis examines what possibilities there are to create a sustainable energy system for Sala Silvergruva considering economics, environment and social aspects.   The report examines nine technologies; wind power, hydropower, solar capture, solar cells, pellet boilers, heat pumps, energy efficiency and storage of heat from greenhouses or district heating. These technologies are analyzed from ten different aspects representing the sustainability demands. In the analysis recommendations are given according investment to each technology. The thesis culminates in a result map which clearly indicates what requirements the various techniques fulfill. The following discussion will lead to a conclusion that present the steps to be taken in order to create a sustainable energy system for Sala Silvergruva AB.   Pellet boilers and heat pumps show to currently be the most resilient solutions. Due to the age and properties of the houses energy-efficiency investments should also be made. These investments are expected to be repaid in 1-5 years.   There are financial incentives for the local energy company Sala-Heby Energi AB to build storage for district heating water in the mine. Such a solution is found to create benefits for both the Sala Silvergruva AB region as a whole. Payback time for the investment is for Sala-Heby Energi AB between 4 to 12 years, depending on size of the storage.

The sales of Ground Source Heat Pumps in Sweden and many other countries are having a rapid growth in the last decade. Today, there are approximately 360 000 systems installed in Sweden, with a growing rate of about 30 000 installations per year. The most common way to exchange heat with the bedrock in ground source heat pump applications is circulating a secondary fluid through a Borehole Heat Exchanger (BHE), a closed loop in a vertical borehole. The fluid transports the heat from the ground to a certain heating and/or cooling application. A fluid with one degree higher or lower temperature coming out from the borehole may represent a 2-3% change in the COP of a heat pump system. It is therefore of great relevance to design cost effective and easy to install borehole heat exchangers. U-pipe BHEs consisting of two equal cylindrical pipes connected together at the borehole bottom have dominated the market for several years in spite of their relatively poor thermal performance and, still, there exist many uncertainties about how to optimize them. Although more efficient BHEs have been discussed for many years, the introduction of new designs has been practically lacking. However, the interest for innovation within this field is increasing nowadays and more effective methods for injecting or extracting heat into/from the ground (better BHEs) with smaller temperature differences between the heat secondary fluid and the surrounding bedrock must be suggested for introduction into the market. This report presents the analysis of several groundwater filled borehole heat exchangers, including standard and alternative U-pipe configurations (e.g. with spacers, grooves), as well as two coaxial designs. The study embraces measurements of borehole deviation, ground water flow, undisturbed ground temperature profile, secondary fluid and groundwater temperature variations in time, theoretical analyses with a FEM software, Distributed Thermal Response Test (DTRT), and pressure drop. Significant attention is devoted to distributed temperature measurements using optic fiber cables along the BHEs during heat extraction and heat injection from and to the ground. / <p>QC 20100517</p> / EFFSYS2 / Efficient Use of Energy Wells for Heat Pumps

The master thesis designs a low-energy mixed-use building in Dolní Kralovice. The thesis consists of three parts, architectural-construction part, environment technology of building and energy assessment report to a photovoltaic power plant. The building has two above-ground floors and a basement under part of the building. The basement includes sanitary facilities and utility room, ground floor includes a restaurant and small sports hall and first floor offices. The building is founded on reinforced concrete foundation slab and foundation pads. The vertical load-bearing structures are designed as a frame system with shear core. Horizontal load-bearing structures are designed as cast-in-place reinforced slabs. External wall is designed from aerated concrete blocks with and mineral wool insulation. The building has a flat roof. In the building is air condition and cooling system and heating is with geothermal heat pumps with a borehole collector. Part of electricity demand is covered by photovoltaics on the roof. The thesis was developed in Revit software.

No description available.

<p>With increasing concerns about the global warming effects of HFC refrigerants, low-GWP refrigerants and non-vapor compression heat pumps are investigated as potential mid- and long-term replacements for current vapor compression heat pump systems that rely on high-GWP refrigerants. To address the need for more environmentally friendly space cooling and heating, and water heating solutions. the U.S. Department of Energy (DOE) Office of Energy Efficiency & Renewable Energy (EERE) is supporting the development of smarter, more efficient, and affordable heat pumping systems operating with low- or near-zero GWP refrigerants through different programs including the Energy, Emissions, and Equity (E3) Initiative. In addition, the Emerging Technologies (ET) Program within the Building Technologies Office (BTO) emphasized the research and development efforts needed to support new technologies that could reduce energy usage in residential and commercial buildings by 50\% over the next decades. In the literature, limited studies were found that systematically investigated different combinations of conventional and emerging space conditioning and water heating technologies while accounting for real building loads, different climate zones, utility structures, and current state-of-the-art equipment. Existing literature primarily focused on thermodynamic performance evaluations at fixed boundary conditions. In addition, separate sensible latent cooling (SSLC) and other novel cooling and dehumidification systems (e.g., membrane-based systems) can significantly reduce the electricity usage for space conditioning. To compare the performance of conventional and emerging technologies several figures-of-merit such as the second law efficiency, are often used. However, limitations exist in previous studies to define the thermodynamic reversible limits and second law efficiency for cooling and dehumidification systems.</p><p>This study developed a comprehensive modeling framework to evaluate both current state-of-the-art vapor compression systems and emerging HVAC\&R technologies in real-world scenarios. The platform will be used to assess potential energy savings, scalability issues, and the effectiveness of combined technologies for different buildings, climate conditions, and utility structures.</p><p>To compare HVAC technologies, a new physics-based definition for the reversible limit and the second law efficiencies for cooling and dehumidification systems with air recirculation has been developed. The new framework is then extended to define a novel performance metric, the seasonal second law efficiency, to form a universal benchmark for assessing various cooling and dehumidification systems. Five cooling and dehumidification systems including magnetocaloric cooling, solid desiccant dehumidification, and membrane dehumidification are evaluated using this benchmark. Steady-state thermodynamic models are constructed for each system. Second law efficiency for each system under various outdoor temperatures and indoor sensible heat ratios (SHR) are calculated. The annual electricity usage of the five systems is used to justify the seasonal second law efficiency definition. The results show that compared to conventional vapor compression systems with mechanical dehumidification, the membrane-based AMX-R cycle can reduce annual electricity use by 12.2%-22.2% and increase the seasonal second law efficiency by 36%.</p><p>The advancements of nine not-in-kind (defined as non-vapor compression systems, solid-state, and chemical-based systems) technologies, i.e. magnetocaloric, thermoelectric, elastocaloric, electrocaloric, membrane-based, Vuilleumier, sorption, chemical looping, and desiccant, were reviewed in detail and compared with the state-of-the-art vapor compression systems. Suitable figures-of-merit were defined to compare the different technologies from a thermodynamic standpoint as well as technology readiness level. As a result of the thorough literature review, a roadmap was created to track the development of emerging HVAC&R technologies and future developments. More importantly, the roadmap enabled the identification of several case studies to evaluate potential energy savings both for space conditioning and water heating. Techno-economic studies for eight HVAC configurations for space heating, cooling, and water heating were conducted for a realistic building scenario under various climate conditions. Different combinations of advanced equipment such as heat pump water heater (HPWH), ground-source heat pumps (GSHP), cold-climate heat pumps (CCHP), and membrane-heat pumps were compared with traditional vapor compression heat pumps and gas furnaces. A building model was developed in EnergyPlus and validated with historical data from the DC Nanogrid House at the Purdue University campus. A total of eleven climate zones were considered, and both local weather conditions and utility pricing were implemented in the simulations. Moreover, future SEER2/HSPF2 equipment ratings and E3 Initiative targets were also included in the analyses.</p><p>The initial simulation results provided climate-based equipment selection guidelines and quantitative techno-economic assessments. For instance, CCHPs with two-stage compression in heating mode save 10%-20% in annual heating cost compared with single-stage VCHPs in Climate Zone 4A, 4C, 5A, 5B, 6A, and 6B. Membrane evaporative air-conditioners could provide cooling cost savings in places where is a significant cooling load, such as Zone 1A, 2A, 2B, 3A, 3C, 4A, 5A, and 6A. Gas furnaces should only be used in cold places where the electricity price per kWh to gas price ratio is higher than 3. GSHP has the lowest HVAC annual energy cost in six out of eleven climate zones in the U.S. Dual fuel heat pumps are not always the most economical option but yield better average cost savings among the eleven locations. HPWHs should be recommended in areas where the electricity price to gas price ratio is below 3. </p><p>The developed simulation framework will be instrumental to continue in-depth investigations of current and next-generation heat pump technologies. The ultimate goal of this research is to provide future guidelines on the selection of building-specific and climate-specific equipment solutions that will enable energy savings and future decarbonization strategies (e.g., geospatially-resolved simulations).</p>

The choice of heating system in new residential buildings has a significant effect onthe total life cycle-cost. Rising energy prices and tougher energy demands for newbuildings creates incentive for energy- and cost-efficient solutions. The purpose ofthis project is therefore to investigate how the choice and sizing of a heating systemin a building can be performed with focus on cost-efficiency. The project is conducted as a case study on a residential building during the buildingphase on behalf of INTEC Dalarna AB, a technical engineering company. The project aim is to answer the following questions: – What heating system of district heating, ground source heat pumps or air towater heat pumps is the most cost-effective for a new residential building inthe middle of Sweden? – Is there a specific combination of a heat pump of arbitrary size and peak heating system that is particularly advantageous for the building? – Is IDA ICE suitable for simulation of energy use in buildings with heatpumps? – Does high energy-efficiency also mean high cost-efficiency for the building? The questions will be answered with building simulation software IDA Indoor Climate and Energy along with capital budgeting. The capital budgeting will be performed with net present value and payoff period for the heat pumps over choosingdistrict heating. The results of the project show that a system with ground source heat pumps with acapacity of 50 percent of the annual peak heat demand and electricity for peak loadsis the most cost-efficient option for the building. However, the most energy efficient option is a ground source heat pump with a capacity of 50 percent of the annual peak heat demand with district heating for peak loads. The project also shows that IDA ICE is suitable for simulating the performance of heat pumps in buildings.The conclusion is that a smaller system of ground source is more cost-efficient forthe building, and that the most energy efficient option is not always equal to themost cost-efficient over time.

District cooling supply is vital for service, commercial and industrial sectors like hospitals, data centers, supermarkets and sensitive laboratory facilities. The main cooling demand in the case of Sweden also originates from these sectors. The cooling demand in Stockholm is expanding mainly because of demand for comfort cooling, and data centers are rising. To cover the existing cooling demand and rising cooling demand, different cooling strategies have to be employed for optimal production of cold. This project concerns the optimization of such a district cooling system with primarily cold storage. This is achieved by choosing a case study network, namely considering the district cooling network of Norrenergi AB, in Sweden. Norrenergi AB is a company involved in supplying district cooling for cold consumers situated around Solna and Sundbyberg regions. The company provides around 70 GWh district cooling per year. The sources for the district cooling supply are free cooling, electrically driven chillers, and cold recovery from heat pumps. Besides these cold sources, currently, the parts of the peak cold demand are shaved using cold storage that is more cost-effectively charged during night-time, adopting the concept of power-to-cold. In running the district cooling system operation, Norrenergi AB’s current electricity mix is 100% renewable. In this thesis work, the existing district cooling network of Norrenergi AB is modeled using BoFiT optimization software (which is the base scenario), and then four future scenarios are developed, considering new, additional cold storages. The scenarios developed were meant to further optimize the existing district cooling grid to cater to the same existing total demand. This is assessed by integrating respective cold storages having larger (i.e., 15 MW capacity) or smaller (i.e., two cold storages each with 3 MW capacity) into the existing district cooling grid. The 15 MW capacity cold storage is integrated into Sundbybergsverket (Scenario 1) and in Frösundaverket (Scenario 2). While, from the smaller cold storages, the first one is integrated into the system in a manner that it supplies cooling for selected cooling customers, that is Scenario 3. The second small cold storage integrated in a way that supplies cooling to the entire grid, which is Scenario 4. Similar to the existing cold storage, in developed scenarios as well, the power-to-cold concept is utilized by charging the cold storage during the time in which the electricity price is lower (i.e., at night). The key outcome of this thesis work reveals that all the developed scenarios lead to cost savings in terms of the consumed electricity for producing DC. The achieved cost saving from each of the four scenarios developed are 23%, 4%, 13%, and 14%, respectively. Among all these scenarios, the first scenario has led to the largest cutback of DC production cost and impliesthat incorporating larger cold storages in cooling production plants results in higher savings. A performed sensitivity analysis also implies that increasing the supply capacity of free cooling results in production cost savings. Besides, an increased cooling capacity by 30% with respect to the base scenario results in a 10.6% cost saving. This saving infers that it is good to utilize free cooling as far as there is an opportunity to increase the use of free cooling. / Tillgången på kyla är i dag avgörande för service, kommersiella och industriella sektorer som sjukhus, serverhallar, kontor, stormarknader och känsliga laboratorieanläggningar. Den huvudsakliga efterfrågan på kyla i Sverige härstammar också från dessa sektorer. Kylbehovet i Stockholm expanderar främst på grund av efterfrågan på komfortkyla och serverhallar stiger. För att täcka det befintliga kylbehovet och den stigande efterfrågan på kyla, kan olika strategier användas för att uppnå en optimal production av kyla. Detta projekt handlar om optimering av ett fjärrkylsystem med kyllager. Detta har genomförts genom en fallstudie baserad på Norrenergis fjärrkylanät i Sverige. Norrenergi AB är ett företag som bl.a levererar fjärrkyla till kunder i Solna och Sundbyberg. Bolaget levererar cirka 70 GWh fjärrkyla per år, med hjälp av frikyla, kylmaskiner och värmepumpar. Förutom ovannämnda produktion används ett fjärrkyllager för att leverera fjärrkyla och jämna ut lasten över dygnet, och detta laddas när behovet av fjärrkyla är lägre. Elen som används för att producera Norrenergis fjärrkyla är helt förnybar. I detta examensarbete har Norrenergis befintliga fjärrkylanät modellerats med hjälp av BoFiT optimeringsprogram och sedan har fyra framtida scenarion utvecklats, med nya, distribuerade kyllager. De scenarierna som utvecklades var tänkta att ytterligare optimera det befintliga fjärrkylanätet, för att tillgodose samma befintliga totala efterfrågan. Detta bedöms genom att integrera kyllager av olika kapacitet i befintligt fjärrkylanät - ett större 15 MW lager eller två kyllager om vadera 3 MW kapacitet. Ett 15 MW fjärrkyllager integreras i Sundbybergsverket (scenario 1) och i Frösundaverket (scenario 2). De mindre fjärrkyllagren integreras i systemet så att kylning levereras till utvalda kunder (scenario 3). I scenario 4 integreras de mindre lagren så att kylning levereras till hela nätet. Precis som med det existerande kyllagret, ska dessa nya lager i de olika scenariona laddas under natten då elpriset är lägre, därav namnet kraftkyla. De viktigaste resultaten ur detta examensarbete visade att alla utvecklade scenarion ledde till kostnadsbesparingar med hänsyn till elförbrukningen. De uppnådda kostnadsbesparingarna från de fyra scenariona var 23%, 4%, 13% respektive 14%. Bland alla scenarier, leder det första scenariot den största besparingen av produktionskostnaden och medför att integrering av kyllager vid produktionsanläggningarna resulterar i högre besparingar. Den känslighetsanalys som genomfördes innebar också att en ökning av leveranskapaciteten för frikyla leder till besparingar i produktionskostnaderna. En ökad frikylkapacitet med 30% med avseende på basscenariot resulterade i 1% kostnadsbesparing. Denna kostnadsbesparing visar också att det är bra att använda frikyla så länge möjligheten finns att öka användandet av frikyla.

Sweden has goals to reach net-zero emissions by 2045. Although electricity sector is almost fossil free, industry &amp; transport still rely on fossil fuels. Ambitious initiatives such as HYBRIT, growth of EV market &amp; expansion of wind power aim to expedite emission reduction. Decarbonization of transport, industry and large-scale wind &amp; solar PV integration in the future necessitates studying energy system of Sweden at national scale in the context of sector coupling, external transmission &amp; storage technologies. Therefore, this study aims to evaluate the impact of thermal energy storage, hydrogen storage and batteries via Power-to-heat &amp; Power-to-hydrogen strategies in the future Swedish energy system (2045) with high proportions of wind power. Two scenarios SWE_2045 &amp; NFF_2045 were formulated to represent two distinct energy systems of the future. The SWE_2045 energy system still relies on fossil fuels, but to a lower extent compared to 2019 level and has increased levels of electrification and biofuels in the transport and industrial sectors. In comparison, the fossil fuels are completely removed in NFF_2045 and the industrial sector has significant demand for electrolytic hydrogen. Both the scenarios were simulated using EnergyPLAN, a deterministic energy system model, under each storage technology. The results indicate that HPs coupled with TES has the potential to increase wind integration from 29.12% to 31.8% in SWE_2045 and 26.78% to 29.17% in NFF_2045. HP &amp; TES also reduces heat production from boilers by 67% to 72% depending on the scenario, leading to overall reduction in total fuel and annual costs by at least 2.5% and 0.5% respectively. However, for wind integration of 31.1% in SWE_2045 the annual cost increases by 5.1% with hydrogen storage compared to TES. However, hydrogen storage shows better performance in NFF_2045, wherein the wind integration increases from 26.78% to 29.3%. Furthermore, increasing hydrogen storage for a lower wind capacity (60 GW) in NFF_2045 reduces both electricity import and export while simultaneously increasing the contribution of storage in fulfilling the hydrogen demand from 1.62% to 6.2%. Compared to TES and HS, the contribution of battery storage is minimal in sector integration. For increase in wind integration of 28% to 29%, the annual cost of a system with battery storage is 1.3% to 2% higher than that of the system with TES and hydrogen storage respectively. Therefore, HPs coupled with TES can improve flexibility in both scenarios. Hydrogen storage is not a promising option if the end goal is only to store excess electricity, as shown by the results in SWE_2045. However, it demonstrates better utilization in terms of wind integration, reduction in electricity import and export when there is a considerable demand for hydrogen, as in the case of NFF_2045. / Sverige ligger i framkant när det gäller avkarbonisering och har mål att nå nettonollutsläpp till 2045. Även om elsektorn är nästan fossilfri, är industri och transport fortfarande beroende av fossila bränslen. Ambitiösa initiativ som Hydrogen Breakthrough Ironmaking Technology (HYBRIT), tillväxt av elbilsmarknaden och expansion av vindkraft syftar till att påskynda utsläppsminskningar. Dekarbonisering av transport, industri och storskalig vind- och solcellsintegrering i framtiden kräver att man studerar Sveriges energisystem i nationell skala i samband med sektorskoppling, extern transmissions- och lagringsteknik.  Därför syftar denna studie till att bestämma effekten av termisk energilagring, vätelagring och batterier via Power-to-heat &amp; Power-to-hydrogen-strategier i det framtida svenska energisystemet (2045) med höga andelar vindkraft. Två scenarier SWE_2045 &amp; NFF_2045 formulerades för att representera två distinkta framtidens energisystem. Energisystemet SWE_2045 är fortfarande beroende av fossila bränslen, men i lägre utsträckning jämfört med 2019 års nivå och har ökat nivåerna av elektrifiering och biobränslen inom transport- och industrisektorn. Som jämförelse är de fossila bränslena helt borttagna i NFF_2045-scenariot där transportsektorn endast är beroende av el och biobränslen, medan industrisektorn har en betydande efterfrågan på elektrolytiskt väte. Båda energisystemen simuleras med EnergyPLAN, en deterministisk energisystemmodell, för olika testfall under varje lagringsteknik. Resultatet av simuleringen bedömdes i termer av kritisk överskottselproduktion, potential för ytterligare vindintegration, total bränslebalans i systemet och årliga kostnader.  Resultatet indikerar att värmepumpar i kombination med termisk energilagring kan förbättra flexibiliteten i båda scenarierna genom att minska den kritiska överskottselproduktionen och bränsleförbrukningen samtidigt som vindintegrationen förbättras. Vätgaslagring är inget lovande alternativ om målet är att endast lagra överskottsel, vilket framgår av vindintegrationsnivåerna i SWE_2045. Det förbättrar dock vindintegration och tillförlitlighet avsevärt när det finns en betydande efterfrågan på vätgas i NFF_2045. Som jämförelse är batteriernas bidrag till vindintegration minimalt i båda scenarierna i samband med sektorintegration på grund av utnyttjandet av överskottsel av värmepumpar och extern överföring av restel. Valet av lagringsteknik i framtiden beror dock på dess tekniska ekonomiska utveckling och energipolitik.