Submitted by Rosivalda Pereira (mrs.pereira@ufma.br) on 2017-06-06T20:07:41Z No. of bitstreams: 1 RaffaelPinto.pdf: 7905766 bytes, checksum: 7f7997961e840698d9d936cdea00b602 (MD5) / Made available in DSpace on 2017-06-06T20:07:41Z (GMT). No. of bitstreams: 1 RaffaelPinto.pdf: 7905766 bytes, checksum: 7f7997961e840698d9d936cdea00b602 (MD5) Previous issue date: 2008-05-21 / Fundação de Amparo à Pesquisa e ao Desenvolvimento Científico e Tecnológico do Maranhão (FAPEMA) / In this work have been investigated the dielectric and vibrational properties of the ORMOSIL membranes based on PDMS and TEOS doped with MDS using the Di erential Scanning Calorimetry (DSC), impedance, Raman and infrareds spectroscopy technics. Such membranes are hybrid organic-inorganic materials with potential application in PEMFC (Proton Exchange Membrane Fuel Cell) and were doped with concentrations 0%(Pure Membrane), 5%, 10%, 20% e 30% of MDS. The thermal measurements were performed in the range from room temperature and 550 oC. The results showed that, after the MDS inclusion, the membranes absorb water. Besides, then thermal stability of the membranes decreased with the MDS inclusion. The dielectrics measurements were performed in temperature range of 313K-373K. The results showed that room temperature conductivity increases linearly with the frequency, until 353K, suggesting a hopping conduction and leaving this linear behavior above 353K. Besides, it was observed that conductivity doesn't increases linearly with MDS concentration, but increases until maximal value for 20% MDS concentration and decreases again for 30% MDS concentration de ning a synergetic e ect, which probably is associate with con gurational arrange of microcristallites MDS. Another feature of that membranes is a relaxation process visible in the electrical module graphics which appear just in doped membranes, being however, due to the MDS. The vibrational properties of hybrids membranes were obtained through Raman scattering and infrared. The results con rmed the presence of Si¡O¡Si, Si¡C, Si¡OH, C2H5, Si¡CH3, CH3, CH2, C¡H, S=O and S¡O groups. Where the S=O and S¡O groups are presents just in MDS compound. Consequently, their respective peaks appear only in the doped membrane spectra. / Neste trabalho foram investigadas as propriedades térmicas, dielétricas e vibracionais das membranas de ORMOSIL baseadas em PDMS e TEOS dopadas com MDS através das técnicas de calorimetria diferencial de varredura, espectroscopias de impedância, Raman e infravermelho. Essas membranas são materiais híbridos orgânico-inorgânico com grande potencialidade de aplicação em células combustíveis do tipo PEM (Proton Exchange Membrane) e foram dopadas nas concentrações de 0%(Pura), 5%, 10%, 20% e 30% de MDS. As medidas térmicas foram realizadas entre a temperatura ambiente e 500 oC e mostraram que as membranas passam a absorver água quando o MDS é inserido. Mostraram também que as membranas têm sua estabilidade térmica reduzida quando o MDS é inserido. As medidas dielétricas foram realizadas no intervalo de temperatura entre 40 e 100oC. Os resultados mostraram que a condutividade à temperatura ambiente aumenta de maneira praticamente linear com a freqüência, mantendo-se assim até 80±C sugerindo uma condução por hopping e deixando de ter esse comportamento linear para temperaturas acima de 80±C. Observou-se também que a condutividade não aumenta linearmente com a concentração de MDS, mas atinge um valor máximo para a membrana com 20% de MDS e diminui novamente para a membrana com 30% de MDS caracterizando assim um efeito sinergético, que provavelmente está associado ao arranjo configuracional dos microcristalitos do MDS. Uma outra característica interessante dessas membranas, é um processo de relaxação visível nos grá cos do módulo elétrico o qual consta apenas nas membranas dopadas, sendo portanto, característico do MDS. As propriedades vibracionais desses materiais híbridos foram determinadas através de medidas do espalhamento Raman. Os resultados da espectroscopia Raman e infravermelho confirmaram a presença dos grupos Si¡O¡Si, Si¡C, Si¡OH, C2H5, Si¡CH3, CH3, CH2, C¡H, S=O e S¡O. Onde estes dois últimos estão presentes somente no MDS e, por essa razão, seus respectivos picos só se apresentaram no espectro das membranas dopadas.

L’objectif de ce travail de thèse a été de développer l’ingénierie des polymères liquides ioniques(PILs) de type imidazolium ainsi qu’une nouvelle famille de copolymères à blocs apparentés.Des PILs type imidazolium ont été utilisés en tant que polymères réactifs pour la catalyse organique etla modification chimique par post-polymérisation. Divers composés (homopolymères, copolymèresstatistiques de type styrénique, polymères réticulés) stables à l'air, portant divers contre-anions (bromures,hydrogénocarbonates, carboxylates), ont été spécialement conçus via des stratégies de synthèserelativement simples. La génération de carbènes N-hétérocycliques supportés sur polymères (poly(NHC)s)a permis de comparer les performances catalytiques de tous ces précurseurs à travers des réactions deréférence de la catalyse organique. Spécifiquement, les copolymères statistiques type styrénique peuventégalement être fonctionnalisés de manière stoechiométrique par post-polymérisation avec différentssubstrats électrophiles (e.g. CS2, isothiocyanate, métaux de transition).Une nouvelle famille de copolymère à blocs contenant un bloc poly(acétate de vinyle) et un bloc detype poly(bromure de N-vinyl-3-alkylimidazolium), a été synthétisé par CMRP. La capacité de cescomposés à s'auto-assembler en diverses mésostructures en masse comme en solution a ensuite étédémontrée. Des mesures de conductivité ionique ont montré l’influence de la préparation des échantillonset des conditions de mesures sur les valeurs obtenues. Le comportement en solution par la réactivité ioniquedu bloc PIL et la modification chimique du bloc hydrophobe poly(acétate de vinyle) en hydrophilepoly(alcool vinylique) ont permis la formation de différentes nanostructures micellaires.Mots clés : Polymères liquides ioniques, Copolymères à blocs, Imidazolium, catalyse organique,Modification post-polymérisation, Auto-assemblage, Conductivité ionique, nanoparticules d’or. / The aim of this PhD work is to expand the scope of engineered imidazolium-based poly(ionicliquid)s (PILs) and their related PIL-block copolymers (PIL BCPs).The use of the imidazolium-based PILs as true reactive polymers for organocatalysis and post-chemicalmodification is first described. Miscellaneous air-stable PIL derivatives featuring various counter-anions(e.g. bromides, hydrogen carbonates, carboxylates), including homopolymers, statistical copolymers ofstyrenic-type and crosslinked copolymer networks have been specifically designed by relatively simplesynthetic strategies. The generation of related polymer-supported N-heterocyclic carbenes, poly(NHC)s,enables comparing the catalytic performances in selected organocatalyzed reactions. Specific polystyrenebasedcoPILs can be also stoichiometrically derivatized by post-chemical modification using variouselectrophilic substrates (e.g. CS2, isothiocyanate, transition metals).A novel family of imidazolium-based PIL BCPs, namely poly(vinyl acetate)-b-poly(N-vinyl-3-alkylimidazolium bromide)s synthesized by CMRP, is then described. The ability of these compounds toself-assemble into various types of mesostructures in bulk or in solution has been demonstrated. Ionicconductivity measurements evidenced the influence of sample preparation and measurement conditions.The behavior in solution evidenced via the ionic responsiveness of the PIL block but also by post-chemicalmodification of the hydrophobic poly(vinyl acetate) block into hydrophilic poly(vinyl alcohol) theformation of various micelle-like nanostructures.Keywords: Poly(ionic liquid)s, Block copolymers, Imidazolium, Organocatalysis, Post-polymerizationmodification, Self-assembly, Ionic conductivity, Gold nanoparticles / El objetivo de esta tesis fue el desarrollo de polímeros de ingeniería iónicoslíquidos (pils) y tipo imidazolio una nueva familia de copolímeros de bloques relacionados.Lager tipo imidazolio fueron utilizados como reactivos para la catálisis orgánica ymodificación química de polímeros después de la polimerización. Varios compuestos(homopolímeros, copolímeros aleatorios de tipo estireno, polímeros reticulados) estable en elaire, contra de la realización diversos aniones (bromuros, bicarbonatos, carboxilatos), hansido especialmente diseñadas utilizando estrategias de síntesis relativamente simple. Se utilizóla generación de carbenos N-heterocíclicos soportado sobre polímeros (poli (NHC) s) paracomparar el rendimiento catalítico de estos precursores de referencia a través de reacciones decatálisis orgánica. Específicamente, los copolímeros de tipo estireno también se puedenfuncionalizar sustratos por polimerización posterior estequiométricamente con diferenteselectrófilos (por ejemplo, metales CS2, isotiocianato, de transición).Una nueva familia de copolímero de bloque que contiene un poli (acetato de vinilo) y unbloque de poli (bromuro de N-vinil-3-alquilimidazolio) se sintetizó en CMRP. La capacidadde estos compuestos a auto-ensamblan en varias mesoestructuras como entonces se demostrósolución en masa. Mediciones de conductividad iónica han demostrado la influencia de lascondiciones de preparación y medición de la muestra en los valores obtenidos. Elcomportamiento en solución por el bloque PIL reactividad de iones, y la modificaciónquímica del bloque hidrófobo de poli (acetato de vinilo) hidrófilo poli (alcohol vinílico)permitió la formación de nanoestructuras diferentes micelares.Palabras clave: polímeros líquidos iónicos, copolímeros de bloque, imidazolio, catálisisorgánica, Cambiar post-polimerización, auto-ensamblaje, conductividad iónica, lasnanopartículas de oro.

Fast ionic conductors, i.e. materials in which charge transport mainly occurs through the motion of ions, are an important class of materials with immense scope for industrial applications. There are different classes of fast ionic conductors e.g. polymer electrolytes, glasses, oxide ion conductors etc. and they find applications such as solid electrolytes in batteries, in fuel cells and in electro active sensors. There are mixed conducting materials as well which have both ions and electrons as conducting species that are used as electrode materials. Specifically, polymer electrolytes 1−3 have been in use in lithium polymer batteries, which have much more advantages compared to other secondary batteries. Polymer electrolyte membranes have been in use in direct methanol fuel cells (DMFC). The membranes act as proton conductors and allow the protons produced from the fuel (methanol) to pass through. Oxide ion conductors are used in high temperature solid oxide fuel cells (SOFC) and they conduct via oxygen ion vacancies. Fuel cells are rapidly replacing the internal combustion engines, because they are more energy efficient and environment friendly. The present thesis is concerned with the preparation, characterization and conductivity studies on the following fast ionic conductors: (MPEG)xLiClO4, (MPEG)xLiCF3SO3 where (MPEG) is methoxy poly(ethylene glycol), the hydrotalcite [Mg0.66Al0.33(OH)2][(CO3)0.17.mH2O] and the nanocomposite SPE, (PEG)46 LiClO4 with dispersed nanoparticles of hydrotalcite. We also present our investigations of spin probe electron spin resonance (SPESR) as a possible technique to determine the glass transition temperature (Tg) of polymer electrolytes where the conventional technique of Tg determination, namely, differential scanning calorimetry, (DSC), is not useful due to the high crystallinity of the polymers. In the following we summarize the main contents of the thesis. In Chapter 1 we provide a brief introduction to the phenomenon of fast ionic conduction. A description of the different experimental techniques used as well as the relevant theories is also given in this chapter. In most solid polymer electrolytes (SPE), the usability is limited by the low value of the ionic conductivity. A number of different routes to enhance the electrical, thermal and mechanical properties of these materials is presently under investigation. One such route to enhance the ionic conductivity in polymer electrolytes is by irradiating the polymer electrolyte with gamma rays, electron beam, ion beams etc. In Chapter 2, we describe our work on the effect of electron beam (e-beam) irradiation on the solid polymer electrolytes (MPEG)xLiClO4 and (MPEG)xLiCF3SO3. The polymer used is methoxy poly(ethylene glycol) or poly(ethylene glycol) methyl ether with a molecular weight 2000. Salts used are LiClO4 and LiCF3SO3. ’x’ in the subscript is a measure of the salt concentration; it is the ratio of the number of ether oxygens in the polymer chain to that of the Li+ ion. ’x’ values chosen are 100, 46, 30 and 16. Nearly one order of magnitude increase in the conductivity is observed for samples (MPEG)100LiClO4 and (MPEG)16LiCF3SO3 on irradiation. It was found that the increase in the net ionic conductivity is a function of both the irradiation dose and the salt concentration. The enhanced ionic conductivity remains constant for ∼ 100 hrs, which signifies a possible near permanent change in the polymer electrolyte system due to irradiation. The samples were also characterized using DSC and Fourier transform infrared spectroscopy (FTIR). DSC results could be correlated with conductivity findings, giving low Tg values for samples having high conductivity. It was also found that there is a small increase in the crystalline fraction of the samples on irradiation, which agrees with earlier reports on samples irradiated with low dosage. FTIR results are suggestive of decreased cross linking as the reason for increased ionic conductivity. However, this aspect needs a further confirmatory look before the findings can be termed conclusive. In Chapter 3, we describe the studies we have carried out on Li -doped hydrotalcite. We report the details of preparation and characterization of hydrotalcite as well as NMR and ionic conductivity measurements on both doped (with Li+ ions) and undoped hydrotalcite. Hydrotalcite was prepared by co-precipitation method and the composition of hydrotalcite was chosen as [Mg0.66Al0.33(OH)2][(CO3)0.17.mH2O]. Samples were prepared with salt (LiClO4) concentration 5 %, 10 %, 15 %, 20 % and 25 %. It was found that the highest ionic conductivity occurs for the sample with 20 % doping. 7Li NMR plots for all the samples clearly show an overlap of a Gaussian and a Lorentzian lineshape. The Gaussian line is because of the presence of a less mobile fraction of the 7Li+ ions and the Lorentzian line is because of the presence of a more mobile fraction of 7Li+ ions. The highest ionic conductivity was found for the salt concentration 20 % and from the room temperature 7Li NMR studies we found that for this particular concentration, the mobile fraction of the 7Li ion is also maximum. Without the salt doping, the conductivity of the sample was too small to be measured. Temperature variation of both 1H and 7Li NMR was also done, to compare the ionic conductivities from NMR. Another method to obtain enhanced properties in polymer electrolytes is by forming ’nanocomposite’ polymer electrolytes. Nanocomposites are formed by dispersing nanoparticles of certain materials in the polymer electrolyte matrix. Till now, nanoparticles used are mostly oxides of metals, e.g. Al2O3, TiO2, MgO, SiO2 etc and clays like montmorillonite, liponite, hydrotalcite etc. Chapter 4 describes the preparation and characterization of the nanocomposite polymer electrolyte (PEG)46LiClO4 formed with hydrotalcite nanoparticles. The polymer used is PEG, poly(ethylene glycol) of molecular weight 2000, and salt used is LiClO4. The salt concentration is selected so as to give the highest ionic conductivity for the solid polymer electrolyte. Hydrotalcite belongs to a class of materials called LDH, layered double hydroxides. The composition selected is [Mg0.66Al0.33(OH)2][(CO3)0.17 .mH2O], since this is the most stable composition. These materials are easy to prepare in the nano size and are being used in a number of applications. These are characterized by the presence of layers of positively charged double hydroxides separated by layers of anions and water molecules. The water molecules give stability to the structure. Nanoparticles of hydrotalcite were prepared in the laboratory itself. XRD data of hydrotalcite confirm the crystal structure. TEM data show the particle size to be ∼ 50 nm. The polymer electrolyte (PEG)46LiClO4 was doped with these nanoparticles and the doping levels are 1.8 %, 2.1 %, 2.7 %, 3.6 % and 4.5 % by weight. Impedance spectroscopy was used to find the ionic conductivity. We have found that the sample with a doping of 3.6 % by weight gives the highest ionic conductivity and the increase in ionic conductivity is nearly one order of magnitude. DSC was used for thermal characterization of these nanocomposites. The glass transition temperatures, Tg , found from DSC measurements corroborates the ionic conductivity data, giving the lowest Tg for the sample with highest conductivity. Temperature variation of the ionic conductivity shows Arrhenius behavior. 7Li NMR was done on the pristine SPE (PEG)46LiClO4 and the nanocomposite of (PEG)46LiClO4 with 3.6 % filler. The ionic conductivity was also estimated from the temperature variation of 7Li NMR line widths. Studies on the DSC endotherms of the nanocomposites give the fractional crystallinity of the samples. From these studies it can be concluded that the variation in ionic conductivity can be attributed to the change in fractional crystallinity; the nanocomposite polymer electrolyte having highest ionic conductivity, i.e. the NCPE with filler concentration of 3.6 % also has the lowest fractional crystallinity. Additionally, a possible increase in the segmental motion inferred from a reduction in the glass transition temperature coupled with a lowering of the activation energy may also contribute to the increased ionic conductivity in the nanocomposite polymer electrolyte. Glass transition temperature Tg has a very important role in studying the dynamics of polymer electrolytes. In Chapter 5, we explore the possibility of using spin probe electron spin resonance (SPESR) as a tool to study the glass transition temperature of polymer electrolytes. When the temperature of the polymer is increased across the glass transition, the viscosity of the sample decreases. This corresponds to a transition from a slow tumbling regime with τc = 10−6 s to a fast tumbling regime with τc = 10−9 s where τc is the correlation time for the probe dynamics. Spin probe ESR can be used to probe this transition in polymers. We have used 4-hydroxy tempo (TEMPOL) as the spin probe which is dispersed in the nanocomposite polymer electrolyte based on (PEG)46LiClO4 and hydrotalcite. Below and across the glass transition, this nitroxide probe exhibits a powder pattern showing both Zeeman (g) and hyperfine (hf) interaction anisotropy. When the frequency of the dynamics increases such that the jump frequency f is of the same order of magnitude as the anisotropy of the hf interaction, i.e., ∼ 108 Hz, the anisotropy of the interactions averages out and a spectrum of reduced splitting and increased symmetry in the line shape is observed. This splitting corresponds to the nonvanishing isotropic value of the hyperfine tensor and is observed at a temperature higher than but correlated with Tg. The crossover from the anisotropic to isotropic spectrum is reflected in a sharp reduction in the separation between the two outermost components of the ESR spectrum, which corresponds to twice the value of the z-principal component of the nitrogen hyperfine tensor, 2Azz, from ∼75 G to ∼ 35 G. In our study, we have varied the concentration of the nano-fillers. The Tg for all the samples were estimated from the measurement of T50G and the known correlation between 4 T50G and Tg, where T50G is the temperature at which the extrema separation (2Azz) of the ESR spectra becomes 50 Gauss. The values obtained from this method are compared with the values found from DSC done on the same samples. Within experimental error, these two techniques give reasonably close values. Tg’s were also estimated by a cross over in the correlation time (τc) vs temperature plot. The τc values were calculated using a spectral simulation program. We conclude that spin probe ESR can be an alternative to the DSC technique for polymers with high fraction of crystallinity, for which DSC often does not give any glass transition signature. In Appendix I, ionic conductivity studies on quenched and gamma irradiated polymer electrolytes (PEG)46LiClO4 and (MPEG)16LiClO4 is done. It is observed that, (i) the samples quenched to 77 K after melting show enhancement of ionic conductivity by a factor of 3 & 4; (ii) on irradiation, the ionic conductivity decreases for a dose of 5 kGy and subsequently, keeps on increasing for higher doses of 10 kGy and 15 kGy. In Appendix II, the BASIC language program (eq-res.bas) used for impedance data analysis is given.

State of the art conductivity equipment has been used to measure deuterium isotope effects on the molar conductivity of strong electrolytes in the temperature range of 298 K to 598 K as a means of exploring solvation effects under hydrothermal conditions. Individual ionic contributions were determined by extrapolation of published transference number data to elevated temperature. The temperature dependence of the Walden product ratio indicates that there is little difference in the transport of ions between light and heavy water . Excess conductivity observed in hydrogen and deuterium compounds arising from proton hopping in hydrogen-bonded networks has been determined in the temperature range of 318 K to 598 K for the first time

No description available.

The thesis entitled “Towards the Design of Functional Materials: Evaluation based on Crystal Structure, Photocatalysis and Conductivity Measurements” consist of six chapters. A short introductory note outlines the basis of designing functional materials, different synthetic procedures, characterization techniques and properties such as photocatalysis and ionic conductivity. Chapter 1 describes the effect of Ti doping on photocatalytic activity in orthorhombic perovskite type LnVO3. All the compounds were synthesized by solid state method. Rietveld refinement with high resolution PXRD reveals that the substituent Ti occupies V site rather than Ln Site. Ti substituted compound showed higher photocatalytic activity than the unsubstituted compound and is comparable with that of commercial catalyst. These classes of compounds showed specific degradation towards chlorinated compounds. Chapter 2 discusses the solution combustion synthesis of γ(L)-Bi2MoO6 and its photocatalytic activity under solar radiation. The particle sizes were in the range 300–500 nm with a band gap of 2.51 eV. The degradation of wide variety of cationic and anionic dyes was investigated under solar radiation. Despite the low surface area (<1 m2/g), γ(L)-Bi2MoO6 showed higher photocatalytic activity under solar radiation due to its electronic and morphological properties. Chapter 3 presents a series of visible light photocatalyst M2Ce2O7, synthesized via solution combustion method and characterized by powder X-ray diffraction, solid-state UV-Visible diffuse reflectance spectra, SEM and TEM. The structure of Bi2Ce2O7 has been determined using laboratory as well as synchrotron PXRD. It crystallizes in a disordered F-type structure. The particle sizes are in the range 5–6 nm, band gaps lie within the range 1.7 to 3.2 eV. Bi2Ce2O7 shows high photocatalytic activity, comparable to the commercial Degussa P-25 TiO2 under solar radiation. Chapter 4 examines the effect of Bismuth substitution on crystal chemistry, photocatalysis and conductivity in Sr3V2O8, a variant of palmierite class. These compounds were synthesized by ceramic method and powder X-ray data reveals the limit of the Bi substitution in Sr3-xBi2x/3V2O8 is x=0.4. Single crystal study followed by careful difference Fourier analysis shows that Bi occupies a unique 18h position which is different than Sr1 and Sr2 position. The experimental band gap for Sr3V2O8 was calculated to be 3.45 eV and upon substitution band gap of the material decreases and reaches a value 3.15 eV for the composition x=0.4. Compound exhibits photocatalytic activity specifically towards anionic dyes. However, Bi Substitution leads to lower photocatalytic activity. Chapter 5 describes synthesis, structure, phase transition and ionic conductivity in scheelite type Li0.5Ce0.5MoO4. The compound was synthesized by ceramic method and single crystal study reveals that it crystallizes in the space group I41/a and exhibits conductivity of ~10-3 Ohm-1cm-1 at elevated temperature( 700 °C). It undergoes a first order phase transition around 510 °C. The nature of this transition has been evaluated by laboratory and synchrotron PXRD, DSC, dielectric spectroscopy and variable temperature Raman spectroscopy. The phase transition is shown to be characterized by an iso-structural phase transition which is first example in literature for temperature induced Cowley’s “Type Zero” phase transition. Chapter 6 discusses a new methodology for generating functional materials for fast ion conductors. Several varients of hydrated sodium cadmium bisulfate, Na2Cd2(SO4)3⋅3H2O, Na2Cd(SO4)2⋅2H2O and Na2Cd(SO4)2⋅4H2O have been synthesized and their thermal properties followed by phase transitions have been invesigated. Na2Cd2(SO4)3⋅3H2O (space group P3c). Na2Cd2(SO4)3⋅3H2O loses water completely when heated to 250 °C and transforms to a dehydrated phase (I⎯43d ) whose structure has been established using abinitio powder diffration techniques. Na2Cd(SO4)2⋅2H2O (P21/c) transforms to α−Na2Cd(SO4)2 (space group C2/c) on heating to 150 °C which is a known high ionic conductor. However, when α−Na2Cd(SO4)2 is heated to 570 °C followed by sudden quenching in liquid nitrogen, β−Na2Cd(SO4)2 (P21/c) is formed. β−Na2Cd(SO4)2 takes up water from the atmosphere and gets converted completely to the Kröhnkite type mineral. Further, β−Na2Cd(SO4)2 has a conductivity behavior comparable to α form up to 280 °C, the temperature required for the transformation of β to α form.

This master‘s thesis concerns gel polymer electrolytes formed on a methyl methacrylate base with selected types of nanoparticles. In the thesis are also analyzed the methods for measuring electrochemical properties. The practical portion deals with sample preparations of gel polymer electrolytes with different contents of alkaline salt in a solvent, creating gels with different nanoparticle content and comparing gel polymer electrolytes polymerized with heat and UV radiation. The thesis deals with the evaluation of these samples from the viewpoint of electrical conductivity and potential windows as well as thermal analysis of selected samples.

This graduate thesis is focused on measuring the electrical conductivity of the gel polymeric electrolytes, their preparation and deals with the changes of the performance ratio of the individual substances in gel electrolyte The theoretical part deals with electrochemistry, gel electrolytes, the conductivity of electrolytes, gel electrolytes preparation, methods used to evaluate the measured results and on the properties of the ionic liquids. In the practical part is summarized the process of preparing gel electrolytes, the chemicals to prepare the gels with ionic liquids. The results are evaluated by using impedance technique and linear voltammetry, there are calculated the values of the electrical conductivity of the electrolyte and potential windows.

Les batteries lithium-ion sont présentement d’excellentes candidates pour le stockage électrochimique d’énergie du futur. Cela dit, les batteries lithium-métal pourraient présenter des propriétés électrochimiques encore plus avantageuses. Cependant, ces types de batteries présentent encore des inconvénients, notamment au niveau de leur sécurité. Un des responsables majeurs de ceux-ci est l’électrolyte liquide organique. Parmi les différentes voies exploitables pour améliorer la sécurité de ces technologies, les électrolytes solides polymères (SPE) sont largement étudiés. Classiquement, ces systèmes sont mis en forme en présence de solvants qui sont ensuite évaporés. Aussi, lorsque le processus d’évaporation de solvants est terminé, les échantillons sont habituellement réexposés à l’air ambient. Or, d’une part, malgré le séchage important d’un échantillon, il se peut qu’il reste du solvant de mise en forme résiduelle. D’autre part, l’eau atmosphérique peut s’infiltrer au sein de celui-ci. Cependant, ce ne sont pas des facteurs qui sont considérés dans la recherche présente dans le domaine. Bien que l’influence des solvants résiduels est parfois mentionnée, elle n’est jamais quantifiée de façon convenable, et cela reste un facteur mal compris et souvent omis. Dans cette étude, des échantillons de différents types de SPE ont été préparés selon des conditions standards, leur teneur en solvants résiduels a été contrôlée et analysée par différentes méthodes développées au cours de cette recherche. Pour la quantification de l’eau, un analyseur d’humidité spécifique a été utilisé, et il a été montré que l’eau résiduelle permet d’augmenter les conductivités ioniques des échantillons. Pour la quantification des solvants résiduels organiques, une méthode analytique employant la chromatographie gazeuse couplée à la spectrométrie de masse a été développée. Il a été observé que comme avec l’eau, les solvants résiduels augmentent la conductivité ionique des échantillons étudiés. Cette étude doit montrer aux chercheurs dans le domaine que le contrôle des solvants résiduels est un facteur primordial dans le développement des SPEs, et que c’est un paramètre qui doit être systématiquement évalué. / Lithium-ion batteries are today’s candidates for future long-term electrochemical storage of renewable energies. That said, lithium-metal batteries could offer even more appealing electrochemical properties. However, both types of batteries still suffer from certain technical difficulties such as safety. One of the culprits for their reduced safety is the use of an organic liquid electrolyte. Indeed, the latter is flammable and poses a risk, as numerous battery fire accidents have shown throughout the past years. Luckily, scientific research has been able to propose safer alternatives to liquid electrolytes applicable to lithium batteries by replacing the former by solid state electrolytes. Amongst these systems, solid polymer electrolytes (SPE) can be considered as a promising possibility to eliminating the safety issues. Conventionally, SPEs are prepared in a solvent that is evaporated at the end of the manufacturing. Additionally, atmospheric humidity can infiltrate these materials and alter their properties. However, residual solvent content is seldom mentioned, and even when it is, the specific experimental parameters are lacking which makes it a misunderstood and regularly omitted factor in battery performance evaluation. In this study, residual solvents are quantified in different SPE systems that are prepared according to standard and non-standard procedures. To do so, certain samples have had their solvent content artificially modified in order to control and analyse it. Firstly, water content is assessed using a specific moisture analyser. Secondly, an analytical method employing gas chromatography coupled to mass spectrometry has been developed to determine the residual SPE processing solvent. It has been concluded that, similarly to water, residual solvents also contribute to enhancing ionic conductivities of SPEs. Hopefully, this study will shed light on the importance of controlling residual solvent content in SPEs, and the necessity of systematically assessing that parameter.

Dans le cadre de ces travaux, l’objectif fixé était de développer des polymères aromatiques possédant des propriétés de conduction protonique. Pour y parvenir des motifs de type acide sulfonique ont été introduits le long des chaînes macromoléculaires. La méthodologie de synthèse de ces polymères qui a été choisie, consistait à polymériser des précurseurs contenant dans leur structure un motif perfluoroalkyle sulfoné. Quatre précurseurs originaux ont ainsi été initialement synthétisés. Différents polymères aromatiques ont été préparés à partir de ces précurseurs en faisant varier le taux de séquences perfluoroalkyles sulfonées. Ces polymères ont ensuite été mis en oeuvre sous la forme de membranes denses selon un procédé de coulée évaporation. A partir de ces membranes, des études de gonflement à l’eau et de conductivité ionique ont été réalisées. / As part of this work, the objective was to develop aromatic polymers with proton conduction properties. To achieve this, the sulfonic acid motifs were introduced along the macromolecular chains. The methodology of synthesis of these polymers was to polymerise the precursor containing in their structure a perfluoroalkyl sulfone moieties. Four novel precursors have been initially synthesized. Different aromatic polymers were prepared from these precursors by varying the rate of perfluoroalkyl sulfonated sequences. These polymers were then used in the form of dense membranes obtained by a casting process of evaporation. From these membranes, swelling studies in water and ionic conductivity were carried out.