Thesis (Ph. D.)--West Virginia University, 2003. / Title from document title page. Document formatted into pages; contains xi, 125 p. : ill. (some col.) Includes abstract. Includes bibliographical references (p. 121-125).

Thesis (M. S.)--Electrical and Computer Engineering, Georgia Institute of Technology, 2009. / Committee Chair: William. Alan Doolittle; Committee Member: Jeffrey Nause; Committee Member: Linda S. Milor; Committee Member: Shyh-Chiang Shen; Committee Member: Stephen E. Ralph.

This dissertation shows the properties of lithium niobate and lithium tantalate as a promising substrate for III-nitrides, addresses several problems of integrating compound semiconductor materials on LN and LT. It also suggests some solutions of the addressed problems, including furnace anneals at high temperature. While this furnace anneal improved surface smoothness and III-nitride film adhesion, it also caused the repolarization on the congruent LN (48.39 mole % of Li2O) samples. However, the repolarization was not developed in the stoichiometric LN (49.9 mole % of Li2O) samples during the identical thermal treatment. Also, the structural quality of GaN epitaxial layers showed slight improvement when grown on LT substrates over LN substrates. Conventional epitaxial growth technologies were adapted and modified to implement a successful AlGaN/GaN heterostructure on LN (LT). The heterostructure were analyzed to verify the electrical and material properties using several characterization techniques. Finally, it demonstrates AlGaN/GaN-based HEMT devices on ferroelectric materials that will allow the future development of the multifunctional electrical and optical applications.

Práce se zabývá fyzikálními vlastnostmi pyroelektrických senzorů a jejich praktickým využitím. Součástí práce je návrh a realizace měřící aparatury, jež bude využita k měření fyzikálních vlastností senzorů. Pro měření signálů pyroelektrického senzoru bude navržen nízkošumový zesilovač. Součástí práce je také návrh a realizace algoritmu pro lokalizaci infračerveného zdroje záření (plamene) v prostoru, na základě vyhodnoceného analogového signálu.

In this thesis, the results pertaining to various investigations carried out on Triglycine sulphate (TGS) single crystals, polyvinylidene fluoride (PVDF) films, lithium tantalate (LT)/PVDF nanocomposites and LT thin films are presented with emphasis on the characteristics that are crucial for their use in pyroelectric sensors. TGS single crystals (size 68 x 45 x 42 mm3), which have high pyroelectric coefficients, were grown by slow cooling method using newly designed platform technique based crystal growth work stations. The problem of slow growth rate along c-direction was overcome by placing (010) oriented seeds on the platform. The grown TGS crystals were used for the fabrication of the laser energy meter and temperature sensor. One drawback of TGS is its low Curie temperature (490C). As a consequence when the operating temperature approaches the Curie temperature, the crystals start depolarizing owing to the movement of domains. As a result the linearity of the devices gets affected and restricts the use of TGS. Therefore pyroelectric materials possessing higher Curie temperatures and larger pyroelectric coefficients than that of TGS are desirable. LT in single crystalline form having Curie temperature of ≈6000C has already been in use for pyroelectric device applications. However, growing stoichiometric LT single crystal is very difficult. On the other hand PVDF polymer films (Tc≈1800C) have low pyrolectric coefficients and difficult to pole electrically. Therefore efforts were made to prepare LT/PVDF nanocrystal composites to increase the pyroelectric coefficient of PVDF and to reduce the poling field. Nanoparticles of LT were prepared using sol-gel route. Spherical nanoparticles of size 20-40nm were prepared from sol by adding oleic acid to it. These nanoparticles were characterized using XRD, TEM, DSC and Raman spectroscopy. PVDF films with large percentage of β-phase (ferroelectric phase) were fabricated from solutions prepared using dimethylsulphoxide (DMSO) solvent. PVDF films (30µm thick), embedded with 20-40nm sized nanocrystallites of LT were fabricated to utilize them for pyroelectric sensor applications. The ferroelectric and pyrolectric properties of nano composite films were studied for sensor applications point of view. As a replacement for the single crystals of LT in pyroelectric sensors, investigations were carried out on oriented LT thin films. The studies on LT thin films yielded promising results which could be exploited for pyroelectric sensor applications.

Les matériaux ferroélectriques sont caractérisés par l'existence d'une polarisation électrique spontanée, dont l'orientation peut être inversée par l'application d'un champ électrique adéquat. Permettant de coder l'information sous la forme d'un domaine ferroélectrique, i.e. une région du matériau avec une certaine orientation de la polarisation, les ferroélectriques ouvrent la voie au stockage de masse de très haute densité (>10 Tbit/in ²). Dans ce contexte, nous avons employé la Piezoresponse Force Microscopy (PFM), un mode particulier de Microscope à Force Atomique (AFM), permettant la manipulation et la détection des domaines ferroélectriques à l'échelle du nanomètre. Avec pour objectif d'étudier les mécanismes de formation des domaines par l'intermédiaire d'une pointe AFM, nos travaux ont mis en valeur la cinétique de croissance des domaines dans des films minces monocristallins de LiTaO3, avec une approche complémentaire de celle thermodynamique, dépendante du champ électrique et soulignant le rôle de l'humidité dans une possible conduction de surface. En parallèle, les films de LiTaO3 ont permis d'appréhender davantage la nature électro-mécanique de la réponse PFM, pour notamment relier l'amplitude du signal mesuré à la géométrie du domaine sous pointe. PFM et domaines ferroélectriques se sont en effet révélés tour à tour, objet d'étude et outil de caractérisation. / Ferroelectric materials are characterized by their spontaneous polarization, whose direction can be reversed by the application of a suitable electric field. Using domains, i.e. regions of uniform polarization orientation, as information bits, ferroelectrics opens the pathway towards ultrahigh storage densities (>10 Tbit/in²). In this respect, Piezoresponse Force Microscopy (PFM), a technique derived from Atomic Force Microscopy (AFM), was used to manipulate and detect ferroelectric domains on the nanometer scale. Our study was focused on the domains formation mechanism in the local electric field of a nanosized tip. Within an approach complementary to the thermodynamic one, we underlined the kinetics of domains growth in single-crystal LiTaO3 thin films, and the role of humidity in a possible surface conduction. In parallel, the LiTaO3 thin films were used to better understand the PFM response, in particular the relation between the measured signal and the geometry of the domain below the tip. This way, PFM and ferroelectrics domains alternately appeared as object of study and characterization tool.

Ferroic materials play an increasingly important role in novel (nano-)electronic applications. Recently, research on domain walls (DWs) received a big boost by the discovery of DW conductivity in bismuth ferrite (BiFeO3 ) and lead zirconate titanate (Pb(Zrx Ti1−x )O3) ferroic thin films. These achievements open a realistic and unique perspective to reproducibly engineer conductive paths and nanocontacts of sub-nanometer dimensions into wide-bandgap materials. The possibility to control and induce conductive DWs in insulating templates is a key step towards future innovative nanoelectronic devices [1]. This work focuses on the investigation of the charge transport along conductive DWs in ferroelectric single crystals. In the first part, the photo-induced electronic DC and AC charge transport along such DWs in lithium niobate (LNO) single crystals is examined. The DC conductivity of the bulk and DWs is investigated locally using piezoresponse force microscopy (PFM) and conductive AFM (c-AFM). It is shown that super-bandgap illumination (λ ≤ 310 nm) in combination with (partially) charged 180° DWs increases the DC conductivity of the DWs up to three orders of magnitude compared to the bulk. The DW conductivity is proportional to the charge of the DW given by its inclination angle α with respect to the polar axis. The latter can be increased by doping the crystal with magnesium (0 to 7 mol %) or reduced by sample annealing. The AC conductivity is investigated locally utilizing nanoimpedance microscopy (NIM) and macroscopic impedance measurements. Again, super-bandgap illumination increases the AC conductivity of the DWs. Frequency-dependent measurements are performed to determine an equivalent circuit describing the domains and DWs in a model system. The mixed conduction model for hopping transport in LNO is used to analyze the frequency-dependent complex permittivity. Both, the AC and DC results are then used to establish a model describing the transport along the conductive DW through the insulating domain matrix material. In the last part, the knowledge obtained for LNO is applied to study DWs in lithium tantalate (LTO), barium titanate (BTO) and barium calcium titanate (BCT) single crystals. Under super-bandgap illumination, conductive DWs are found in LTO and BCT as well, whereas a domain-specific conductivity is observed in BTO.

Ferroic materials play an increasingly important role in novel (nano-)electronic applications. Recently, research on domain walls (DWs) received a big boost by the discovery of DW conductivity in bismuth ferrite (BiFeO3 ) and lead zirconate titanate (Pb(Zrx Ti1−x )O3) ferroic thin films. These achievements open a realistic and unique perspective to reproducibly engineer conductive paths and nanocontacts of sub-nanometer dimensions into wide-bandgap materials. The possibility to control and induce conductive DWs in insulating templates is a key step towards future innovative nanoelectronic devices [1]. This work focuses on the investigation of the charge transport along conductive DWs in ferroelectric single crystals. In the first part, the photo-induced electronic DC and AC charge transport along such DWs in lithium niobate (LNO) single crystals is examined. The DC conductivity of the bulk and DWs is investigated locally using piezoresponse force microscopy (PFM) and conductive AFM (c-AFM). It is shown that super-bandgap illumination (λ ≤ 310 nm) in combination with (partially) charged 180° DWs increases the DC conductivity of the DWs up to three orders of magnitude compared to the bulk. The DW conductivity is proportional to the charge of the DW given by its inclination angle α with respect to the polar axis. The latter can be increased by doping the crystal with magnesium (0 to 7 mol %) or reduced by sample annealing. The AC conductivity is investigated locally utilizing nanoimpedance microscopy (NIM) and macroscopic impedance measurements. Again, super-bandgap illumination increases the AC conductivity of the DWs. Frequency-dependent measurements are performed to determine an equivalent circuit describing the domains and DWs in a model system. The mixed conduction model for hopping transport in LNO is used to analyze the frequency-dependent complex permittivity. Both, the AC and DC results are then used to establish a model describing the transport along the conductive DW through the insulating domain matrix material. In the last part, the knowledge obtained for LNO is applied to study DWs in lithium tantalate (LTO), barium titanate (BTO) and barium calcium titanate (BCT) single crystals. Under super-bandgap illumination, conductive DWs are found in LTO and BCT as well, whereas a domain-specific conductivity is observed in BTO.