The lateral resistance of pile foundations has typically been based on the resistance of circular pipe piles. In addition, most instrumented lateral load tests and cases history have involved circular piles. However, piles used in engineering practice may also be non-circular cross-section piles such as square and H piles. Some researchers have theorized that the lateral resistance of square piles will be higher than that of circular piles (Reese and Van Impe, 2001; Briaud et al, 1983; Smith, 1987) for various reasons, but there is not test data to support this claims. To provide basic comparative performance data, lateral load tests were performed on piles with circular, square and H sections. To facilitate comparisons, all the tests piles were approximately 12 inches in width or diameter and were made of steel. The square and circular pipe sections had comparable moments of inertia; however, the H pile was loaded about the weak axis, as is often the case of piles supporting integral abutments, and had a much lower moment of inertia. The granular fill around the pile was compacted to approximately 95% of the standard Proctor maximum density and would be typical of fill for a bridge abutment. Lateral load was applied with a free-head condition at a height of 1 ft above the ground surface. To define the load-deflection response, load was applied incrementally to produce deflection increments of about 0.25 inches up to a maximum deflection of about 3 inches. Although the square and pipe pile sections had nearly the same moment of inertia, the square pile provided lateral resistance that was 20 to 30% higher for a given deflection. The lateral resistance of the H pile was smaller than the other two pile shapes but higher than what it is expected based on the moment of inertia. Back analysis with the computer program LPILE indicates that the pile shape was influencing the lateral resistance. Increasing the effective width to account for the shape effect as suggested by Reese and Van Impe (2001) was insufficient to account for the increased resistance. To provide agreement with the measured response, p-multipliers of 1.2 and 1.35 were required for the square pile and H piles, respectively. The analyses suggest that the increased resistance for the square and H pile sections was a result of increases in both the side shear and normal stress components of resistance. Using the back-calculated p-multipliers provided very good agreement between the measured and computed load-deflection curves and the bending moment versus depth curves.

Passive force-deflection behavior for densely compacted backfills must be considered in bridge design to ensure adequate resistance to both seismic and thermally induced forces. Current codes and practices do not distinguish between skewed and non-skewed bridge abutment geometries; however, in recent years, numerical models and small-scale, plane-strain laboratory tests have suggested a significant reduction in passive force for skewed bridge abutments. Also, various case studies have suggested higher soil stresses might be experienced on the acute side of the skew angle. For these reasons, three large-scale tests were performed with abutment skew angles of 0, 15 and 30 degrees using an existing pile cap [11-ft (3.35-m) wide by 15-ft (4.57-m) long by 5.5-ft (1.68-m) high] and densely compacted sand backfill confined by MSE wingwalls. These tests showed a significant reduction in passive force (approximately 38% as a result of the 15 degree skew angle and 51% as a result of the 30° skew angle. The maximum passive force was achieved at a deflection of approximately 5% of the backwall height; however, a substantial loss in the rate of strength gain was observed at a deflection of approximately 3% of the backwall height for the 15° and 30° skew tests. Additionally, the soil stiffness appears to be largely unaffected by skew angle for small displacements. These results correlate very well with data available from numerical modeling and small-scale lab tests. Maximum vertical backfill displacement and maximum soil pressure measured normal to the skewed backwall face were located on the acute side of the skew for the 15° and 30° skew test. This observation appears to be consistent with observations made in various case studies for skewed bridge abutments. Also, the maximum outward displacement of the MSE wingwalls was located on the obtuse side of the skew. These findings suggest that changes should be made to current codes and practices to properly account for skew angle in bridge design.

Bridge abutments are designed to withstand lateral pressures from thermal expansion and seismic forces. Current design curves have been seen to dangerously over- and under-estimate the peak passive resistance and corresponding deflection of abutment backfills. Similar studies on passive pressure have shown that passive resistance changes with different types of constructed backfills. The effects of changing the length to width ratio, or including MSE wingwalls determine passive force-deflection relationships. The purpose of this study is to determine the effects of the wall heights and of the MSE support on passive pressure and backfill failure, and to compare the field results with various predictive methods. To compare the effects of backfill geometries, three large-scale tests with dense compact sand were performed with abutment backfill heights of 3 ft (0.91 m), 5.5 ft (1.68 m), and 5.5 ft (1.68 m) confined with MSE wingwalls. Using an existing pile cap 11 ft (3.35 m) wide and 5.5 ft (1.68 m) high, width to height ratios for the abutment backfills were 3.7 for the 3ft test, and 2.0 for the 5.5ft and MSE tests. The failure surface for the unconfined backfills exhibited a 3D geometry with failure surfaces extending beyond the edge of the cap, increasing the "effective width", and producing a failure "bulb". In contrast, the constraint provided by the MSE wingwalls produced a more 2D failure geometry. The "effective width" of the failure surface increased as the width to height ratio decreased. In terms of total passive force, the unconfined 5.5ft wall provided about 6% more resistance than the 5.5ft MSE wall. However, in terms of passive force/width the MSE wall provided about 70% more resistance than the unconfined wall, which is more consistent with a plane strain, or 2D, failure geometry. In comparison with predicted forces, the MSE curve never seemed to fit, while the 3ft and 5.5ft curves were better represented with different methods. Even with optimizing between both the unconfined curves, the predicted Log Spiral peak passive forces were most accurate, within 12% of the measured peak resistances. The components of passive force between the unconfined tests suggest the passive force is influenced more by frictional resistance and less by the cohesion as the height of the backwall increases.

A key challenge for maximizing the world’s food supply is crop yield prediction. In this study, three machine models are used to predict the fresh weight (yield) of lettuce plants that are grown inside indoor farms hydroponically using the vertical farming infrastructure, namely, support vector regressor (SVR), random forest regressor (RFR), and deep neural network (DNN).The climate data, nutrient data, and plant growth data are passed as input to train the models to understand the growth pattern based on the available features. The study of evaluation metrics majorly covers Mean Squared Error (MSE), Root Mean Squared Error (RMSE), Mean Absolute Error (MAE), R-squared, and Adjusted R-squared values.The results of the project have shown that the Random Forest with all the features is the best model having the best results with the least cross-validated MAE score and good cross-validated Adjusted R-squared value considering that the error of the prediction is minimal. This is followed by the DNN model with minor differences in the resulting values. The Support Vector Regressor (SVR) model gave a very poor performance with a huge error value that cannot be afforded in this scenario. In this study, we have also compared various evaluating metrics mentioned above and considered the cross-validated MAE and cross-validated Adjusted R-squared metrics. According to our study, MAE had the lowest error value, which is less sensitive to the outliers and adjusted R-squared value helps to understand the variance of the target variable with the predictor variable and adjust the metric to prevent the issues of overfitting.

No description available.

Tidigare studier visar på att blodtrycket hos gravida sjunker under andra trimestern och sedanökar i ett senare skede av graviditeten. Högt blodtryck hos gravida kan medföra hälsorisker, vilket gör mätningar av blodtryck relevanta. Dock uppstår det osäkerhet då olika personer inom vården hanterar blodtrycksmätningarna på olika sätt. Delar av vårdpersonalen avrundarmätvärden och andra gör det inte, vilket kan leda till svårigheter att tolkablodtrycksutvecklingen. I uppsatsen behandlas ett dataset innehållandes blodtrycksvärden hos gravida genom att skatta nio olika linjära regressionsmodeller med blandade effekter. Därefter genomförs en simuleringsstudie med syfte att undersöka hur mätproblem orsakat av avrundningar påverkar parameterskattningar och modellval i en linjär blandad modell. Slutsatsen är att blodtrycksavrundningarna inte påverkar typ 1-felet men påverkar styrkan. Dock innebär inte detta något problem vid fortsatt analys av blodtrycksvärdena i det verkliga datasetet.

This research had an objective of exploring the role of MSEs in LED through analysis of wood-work MSE value chain. The basic research questions underscore what the domestic wood-work value chain looks like; what major weaknesses and challenges confront the operation of MSEs; what major areas of upgrading and inter-firm relations are evident in the sector; and what MSE value chains contribute to LED. The research exercise was based on review of related literature and a field survey, involving MSE operators drawn from the study area (Addis Ababa). Mixed method of analysis (quantitative and qualitative) was employed to deal with the data collected through questionnaires and interviews. Porter’s model of VC (1985) and UNIDO’s description of wood-work VC (2005) were used to provide conceptual framework. The wood-work sub-sector in Ethiopia has a domestic value chain since main inputs are from local sources, designs are by local producers, and products are for domestic markets. Domestic actors govern the allocation of resources and the distribution of benefits. Public enterprises control plantations hence primary inputs. Wholesalers in turn control inputs, which finally reach MSEs through retailers. Design, production and marketing decisions are made by MSE operators. Middlemen are minor as most of the products reach consumers directly. The value-chain’s downstream is thus described by a short distribution-channel. Horizontal, non-market, linkages characterize inter-firm relations; whereas, arm’s length market linkages dominate the supplier-MSE-buyer relations. In the absence of “lead firms”, wood-work MSE value chains fail to qualify for the mainstream “buyer-driven” model. Without buyer-dominated quasi-hierarchical relationship, MSEs exercise “incremental upgrading” through learning-by-doing. Measures taken to upgrade the production process are considerably inclined to the physical (hardware) aspects of the firm. The MSE value-chain is restrained by internal and external problems. The current state of design marks underdeveloped links in the chain and delays entry into competitive markets. Despite the drawbacks, MSEs enable localities mobilize fragmented resources and create employment. MSEs contribute to LED through the value chain, right from input-sourcing to production and marketing. Inter-firm relations and upgrading efforts uphold the contributions. / Development Studies / Ph. D. (Development Studies)

Η παρούσα μεταπτυχιακή διατριβή εντάσσεται ερευνητικά στην περιοχή της Στατιστικής Θεωρίας Αποφάσεων και ειδικότερα στην εκτίμηση των παραμέτρων στο μοντέλο της διπαραμετρικής εκθετικής κατανομής με παράμετρο θέσης μ και παράμετρο κλίμακος σ. Θεωρούμε το πρόβλημα εκτίμησης των παραμέτρων κλίμακας μ και θέσης σ, όταν μ≤c, όπου c είναι μία γνωστή σταθερά. Αποδεικνύουμε ότι σε σχέση με το κριτήριο του Μέσου Τετραγωνικού Σφάλματος (ΜΤΣ), οι βέλτιστοι αναλλοίωτοι εκτιμητές των μ και σ, είναι μη αποδεκτοί όταν μ≤c, και προτείνουμε βελτιωμένους. Επίσης συγκρίνουμε του εκτιμητές αυτούς σε σχέση με το κριτήριο του Pitman. Επιπλέον, προτείνουμε εκτιμητές που είναι καλύτεροι από τους βέλτιστους αναλλοίωτους εκτιμητές, όταν μ≤c, ως προς την συνάρτηση ζημίας LINEX. Τέλος, η θεωρία που αναπτύσσεται εφαρμόζεται σε δύο ανεξάρτητα δείγματα προερχόμενα από εκθετική κατανομή. / The present master thesis deals with the estimation of the location parameter μ and the scale parameter σ of the two-parameter exponential distribution. We consider the problem of estimation of locasion parameter μ and the scale parameter σ, when it is known apriori that μ≤c, where c is a known constant. We establish that with respect to the mean square error (mse) criterion the best affine estimators of μ and σ in the absence of information μ≤c are inadmissible and we propose estimators which are better than these estimators. Also, we compare these estimators with respect to the Pitman Nearness criterion. We propose estimators which are better than the standard estimators in the unrestricted case with respect to the suitable choise of LINEX loss. Finally, the theory developed is applied to the problem of estimating the location and scale parameters of two exponential distributions when the location parameters are ordered.

This research had an objective of exploring the role of MSEs in LED through analysis of wood-work MSE value chain. The basic research questions underscore what the domestic wood-work value chain looks like; what major weaknesses and challenges confront the operation of MSEs; what major areas of upgrading and inter-firm relations are evident in the sector; and what MSE value chains contribute to LED. The research exercise was based on review of related literature and a field survey, involving MSE operators drawn from the study area (Addis Ababa). Mixed method of analysis (quantitative and qualitative) was employed to deal with the data collected through questionnaires and interviews. Porter’s model of VC (1985) and UNIDO’s description of wood-work VC (2005) were used to provide conceptual framework. The wood-work sub-sector in Ethiopia has a domestic value chain since main inputs are from local sources, designs are by local producers, and products are for domestic markets. Domestic actors govern the allocation of resources and the distribution of benefits. Public enterprises control plantations hence primary inputs. Wholesalers in turn control inputs, which finally reach MSEs through retailers. Design, production and marketing decisions are made by MSE operators. Middlemen are minor as most of the products reach consumers directly. The value-chain’s downstream is thus described by a short distribution-channel. Horizontal, non-market, linkages characterize inter-firm relations; whereas, arm’s length market linkages dominate the supplier-MSE-buyer relations. In the absence of “lead firms”, wood-work MSE value chains fail to qualify for the mainstream “buyer-driven” model. Without buyer-dominated quasi-hierarchical relationship, MSEs exercise “incremental upgrading” through learning-by-doing. Measures taken to upgrade the production process are considerably inclined to the physical (hardware) aspects of the firm. The MSE value-chain is restrained by internal and external problems. The current state of design marks underdeveloped links in the chain and delays entry into competitive markets. Despite the drawbacks, MSEs enable localities mobilize fragmented resources and create employment. MSEs contribute to LED through the value chain, right from input-sourcing to production and marketing. Inter-firm relations and upgrading efforts uphold the contributions. / Development Studies / Ph. D. (Development Studies)

Made available in DSpace on 2016-04-25T18:40:14Z (GMT). No. of bitstreams: 1 Valdir Donizete Segato.pdf: 1566486 bytes, checksum: 0466b46a2ebe3438da9eeeeefc33df35 (MD5) Previous issue date: 2015-12-18 / This study aims to reflect on the main difficulties encountered in the adoption of International Accounting Standards by Micro and Small Entities (MSEs) in Brazil, whose annual gross income is up to R$ 3,600,000.00, based on Technical Interpretation General, established in Resolution n. 1418/12 (ITG 1000), the Federal Accounting Council (CFC). Methodologically, the research is categorized as the objectives in exploratory and descriptive and on the procedures in literature and documents. For the literature review was conducted bibliographic research and in electronic media, content analysis of documents relating to accounting standards, raising opinions through questionnaires and interviews, and a description of the data, based on the elaboration of a materiality matrix, which pondered priorities established by key stakeholders, who are the users of accounting information in relation to the issues involved. The research is justified because of the economic and social importance of this segment which contributes to boost supply chains of large corporations and represents - the Brazilian Service of Support for research Micro and Small Entities (SEBRAE) - 99% of the total of 6.4 millions of existing businesses in Brazil, accounting for 52% (16.1 million) of formal jobs in the private sector. The results showed that the main difficulties for the adoption of this International Accounting Standards by MSEs are not related to the conceptual part of these standards, but the difficulties of structural and operational, as prices services charged (fees) incompatible with the responsibility and technical risk of the work, the absence of management and internal control system, the standard practice of tax evasion, among others, added to some of fact interest that the entrepreneur owner of MSEs demonstrates in relation to accounting as a management tool / Este estudo tem por objetivo refletir sobre as principais dificuldades encontradas na adoção do padrão contábil internacional pelas Microempresas e Empresas de Pequeno Porte (MPEs) no Brasil, cuja receita bruta anual é de até R$ 3.600.000,00, com base na Interpretação Técnica Geral, instituída na Resolução nº. 1.418/12 (ITG1000), do Conselho Federal de Contabilidade (CFC). Metodologicamente, a pesquisa se classifica quanto aos objetivos em exploratória e descritiva e quanto aos procedimentos em bibliográfica e documental. Foram realizados levantamentos bibliográficos e em meio eletrônico, análise de conteúdo dos documentos referentes às normas contábeis, levantamento de opiniões por meio de questionários e entrevistas, bem como a descrição dos dados, com base na elaboração de uma matriz de materialidade, que ponderou as prioridades estabelecidas pelos principais stakeholders, que são os usuários das informações contábeis, em relação aos temas envolvidos. A pesquisa se justifica em razão da importância econômica e social deste segmento que contribui para dinamizar as cadeias produtivas das grandes corporações e representa  pela pesquisa do Serviço Brasileiro de Apoio às Micro e Pequenas Empresas (SEBRAE)  99% do total de 6,4 milhões de empresas existentes no Brasil, respondendo por 52% (16,1 milhões) dos empregos com carteira assinada no setor privado. Os resultados obtidos permitem concluir que as principais dificuldades, para a adoção deste padrão contábil internacional pelas MPEs, não estão relacionadas com a parte conceitual destas normas, e sim às dificuldades de ordem estrutural e operacional, como os preços dos serviços cobrados (honorários) incompatíveis com a responsabilidade e risco técnico do trabalho, a inexistência de sistema de gestão e controle interno, a prática recorrente de sonegação de impostos, entre outros, somado ao fato do pouco interesse que o empresário, proprietário das MPEs demonstra em relação à Contabilidade como instrumento de gestão