Over the past decade, fusion research has showed the potential of being a main candidate for energy production for future generations. Further advances in improved fusion performance are therefore vital. This thesis focuses on advanced fusion plasma scenarios and their diagnostic requirements. In particular the design of a motional Stark effect (MSE) diagnostic at the MAST spherical tokamak and the analysis of magneto-hydrodynamic mode feedback control and pulsed poloidal current drive (PPCD) at the reversed field pinch (RFP) experiment EXTRAP T2R are discussed. The MSE diagnostic is important for the determination of the plasma current profile, information that is necessary for studies in advanced confinement scenarios like reversed shear profiles or current holes. The MAST MSE system has two channels and selects the spectral components using 1Å FWHM interference filters. The diagnostic has been commissioned during the fall of 2006 and the results show the feasibility of the technique with rms-noise ~0.5° using a time resolution of 1 ms. Investigations of mirror labyrinths for the future ITER MSE diagnostic highlight the need for careful calibration considerations. Feedback control and PPCD are techniques for improved confinement. Feedback control dramatically decreases impurity influx at the end of discharges while transport in the bulk plasma is largely unaffected. During PPCD the transport is seen to decrease and it is demonstrated that PPCD and feedback control can be employed simultaneously. New and innovative techniques for fusion spectroscopy are furthermore described. This includes the use of correlations in line integrated signals to determine ion emission profiles in poloidally symmetric environments. Good agreement with other diagnostic methods is obtained. The assessment of electron temperature profiles using measured differences between Thomson scattering and vacuum ultra-violet spectroscopy is also shown. / QC 20100907

There is a growing demand for the high quality TV programs such as High Definition TV (HDTV). The CATV network is often a suitable solution to address this demand using a CATV modem delivering high data rate digital signals in a cost effective manner, thereby, utilizing a complex digital modulation scheme is inevitable. Exploiting complex modulation schemes, entails a more sophisticated modulator and distribution system with much tighter tolerances. However, there are always distortions introduced to the modulated signal in the modulator degrading signal quality.<p> In this research, the effect of distortions introduced by the RF band pass filter in the modulator will be considered which cause degradations on the quality of the output Quadrature Amplitude Modulated (QAM) signal. Since the RF filter's amplitude/group delay distortions are not symmetrical in the frequency domain, once translated into the base band they have a complex effect on the QAM signal. Using Matlab, the degradation effects of these distortions on the QAM signal such as Bit Error Rate (BER) is investigated.<p> In order to compensate for the effects of the RF filter distortions, two different methods are proposed. In the first method, a complex base band compensation filter is placed after the pulse shaping filter (SRRC). The coefficients of this complex filter are determined using an optimization algorithm developed during this research. The second approach, uses a pre-equalizer in the form of a Feed Forward FIR structure placed before the pulse shaping filter (SRRC). The coefficients of this pre-equalizer are determined using the equalization algorithm employed in a test receiver, with its tap weights generating the inverse response of the RF filter. The compensation of RF filter distortions in base band, in turn, improves the QAM signal parameters such as Modulation Error Ratio (MER). Finally, the MER of the modulated QAM signal before and after the base band compensation is compared between the two methods, showing a significant enhancement in the RF modulator performance.

There is a growing demand for the high quality TV programs such as High Definition TV (HDTV). The CATV network is often a suitable solution to address this demand using a CATV modem delivering high data rate digital signals in a cost effective manner, thereby, utilizing a complex digital modulation scheme is inevitable. Exploiting complex modulation schemes, entails a more sophisticated modulator and distribution system with much tighter tolerances. However, there are always distortions introduced to the modulated signal in the modulator degrading signal quality.<p> In this research, the effect of distortions introduced by the RF band pass filter in the modulator will be considered which cause degradations on the quality of the output Quadrature Amplitude Modulated (QAM) signal. Since the RF filter's amplitude/group delay distortions are not symmetrical in the frequency domain, once translated into the base band they have a complex effect on the QAM signal. Using Matlab, the degradation effects of these distortions on the QAM signal such as Bit Error Rate (BER) is investigated.<p> In order to compensate for the effects of the RF filter distortions, two different methods are proposed. In the first method, a complex base band compensation filter is placed after the pulse shaping filter (SRRC). The coefficients of this complex filter are determined using an optimization algorithm developed during this research. The second approach, uses a pre-equalizer in the form of a Feed Forward FIR structure placed before the pulse shaping filter (SRRC). The coefficients of this pre-equalizer are determined using the equalization algorithm employed in a test receiver, with its tap weights generating the inverse response of the RF filter. The compensation of RF filter distortions in base band, in turn, improves the QAM signal parameters such as Modulation Error Ratio (MER). Finally, the MER of the modulated QAM signal before and after the base band compensation is compared between the two methods, showing a significant enhancement in the RF modulator performance.

A Mechanically Stabilized Earth (MSE) wall is a vertical grade separation that uses earth reinforcement extending laterally from the wall to take advantage of earth pressure to reduce the required design strength of the wall. MSE wall systems are often prefabricated to reduce construction time, thus improving constructability when compared with conventionally cast-in-place reinforced wall systems. However, there is a lack of knowledge for predicting the service-life of MSE retaining wall systems when recycled backfill materials such as Recycled Asphalt Pavement (RAP) and Crushed Concrete (CC) are used instead of Conventional Fill Material (CFM). The specific knowledge missing is how these recycled materials, when used as backfill in MSE wall systems, affects the corrosion rate of the reinforcing strips. This work addresses this knowledge gap by providing recommendations for MSE wall systems backfilled with CC or RAP, and provides a guide to predict the service-life based on corrosion rate test data obtained from embedding steel and galvanized-steel earth reinforcing strips embedded in MSE wall systems backfilled with CC, RAP, and CFM. Experimental data from samples emulating MSE wall systems with steel and galvanized-steel reinforcing strips embedded in CC and RAP were compared to samples with strips embedded in CFM. The results of the testing provide data and methodologies that may, depending on the environmental exposure conditions, justify the use of RAP and CC for the construction of MSE walls. If these backfill materials are obtained from the construction site, this could provide a significant cost savings during construction.

In the first part, the topic of average channel capacity for Orthogonal Frequency Division Multiplexing (OFDM) under Rayleigh, Rician, Nakagami-m, Hoyt, Weibull and Lognormal fading is addressed. With the assumption that channel state information is known, we deal with a lower bound for the capacity and find closed computable forms for Rician fading without diversity and with Maximum Ratio Combining diversity at the receiver. Approximate expressions are also provided for the capacity lower bound in the case of high Signal to Noise Ratio. This thesis presents two simplified Maximum A Posteriori (MAP) channel estimators to be used in OFDM systems under frequency selective slowly varying Rayleigh fading. Both estimators use parametric models, where the first model assumes exponential frequency domain correlation while the second model is based on the assumption of exponential power delay profile. Expressions for the mean square error of estimations are derived and the relation between the correlation of subchannel taps and error variance is investigated. Dependencies of the proposed estimators&rsquo / performances on the model parameter and noise variance estimation errors are analyzed. We also provide approximations on the estimators&rsquo / algorithms in order to make the estimators practical. Finally, we investigate SER performance of the simplified MAP estimator based on exponential power delay profile assumption used for OFDM systems with QPSK modulation. The results indicate that the proposed estimator performance is always better than that of the ML estimator, and as the subchannel correlation increases the performance comes closer to that of perfectly estimated channel case.

Effort to estimate unknown time-varying channels as a part of high-speed mobile communication systems is of interest especially for next-generation wireless systems. The high computational complexity of the optimal Wiener estimator usually makes its use impractical in fast time-varying channels. As a powerful candidate, the adaptive least mean squares (LMS) algorithm offers a computationally efficient solution with its simple first-order weight-vector update equation. However, the performance of the LMS algorithm deteriorates in time-varying channels as a result of the eigenvalue disparity, i.e., spread, of the input correlation matrix in such chan nels. In this work, we incorporate the L MS algorithm into the well-known bidirectional processing idea to produce an extension called the bidirectional LMS. This algorithm is shown to be robust to the adverse effects of time-varying channels such as large eigenvalue spread. The associated tracking performance is observed to be very close to that of the optimal Wiener filter in many cases and the bidirectional LMS algorithm is therefore referred to as near-optimal. The computational complexity is observed to increase by the bidirectional employment of the LMS algorithm, but nevertheless is significantly lower than that of the optimal Wiener filter. The tracking behavior of the bidirectional LMS algorithm is also analyzed and eventually a steady-state step-size dependent mean square error (MSE) expression is derived for single antenna flat-fading channels with various correlation properties. The aforementioned analysis is then generalized to include single-antenna frequency-selective channels where the so-called ind ependence assumption is no more applicable due to the channel memory at hand, and then to multi-antenna flat-fading channels. The optimal selection of the step-size values is also presented using the results of the MSE analysis. The numerical evaluations show a very good match between the theoretical and the experimental results under various scenarios. The tracking analysis of the bidirectional LMS algorithm is believed to be novel in the sense that although there are several works in the literature on the bidirectional estimation, none of them provides a theoretical analysis on the underlying estimators. An iterative channel estimation scheme is also presented as a more realistic application for each of the estimation algorithms and the channel models under consideration. As a result, the bidirectional LMS algorithm is observed to be very successful for this real-life application with its increased but still practical level of complexity, the near-optimal tracking performa nce and robustness to the imperfect initialization.

在講求品質創新與顧客導向之時代中，隨著顧客的需求和期望，創造產品之一元品質和魅力品質，是促使企業不斷地精益求精之動力，同時也使企業更具競爭力，進而使企業能永續經營。 本研究以CK電腦公司之工業用筆記型電腦HDD為研究對象。公司提出因RT686型號工業用筆記型電腦無法通過軍規振動測試，公司正準備開發新型號。本研究將對舊型號之電腦HDD內部緩衝材做設計，待找到防振效果最佳之緩衝材設計後，將其應用至新機型電腦，使其能通過軍規振動測試。 透過實驗設計方法規劃和執行三階段之HDD振動實驗，並收集實驗數據，再分別利用MSE法、變異數分析結合迴歸分析法、回應圖和回應表分析法、類別資料分析法和倒傳遞類神經網路方法分析，以決定最佳緩衝材設計。在進行確認實驗後，找到不會因為外部環境之振動，使HDD之運轉速度發生暫停和轉慢情形之最佳緩衝材設計，防振效果良好，而且此緩衝材設計只使用一種材質，更是節省公司材料生產上之成本。

We address the problem of image denoising for additive white Gaussian noise (AWGN), Poisson noise, and Chi-squared noise scenarios. Thermal noise in electronic circuitry in camera hardware can be modeled as AWGN. Poisson noise is used to model the randomness associated with photon counting during image acquisition. Chi-squared noise statistics are appropriate in imaging modalities such as Magnetic Resonance Imaging (MRI). AWGN is additive, while Poisson noise is neither additive nor multiplicative. Although Chi-squared noise is derived from AWGN statistics, it is non-additive. Mean-square error (MSE) is the most widely used metric to quantify denoising performance. In parametric denoising approaches, the optimal parameters of the denoising function are chosen by employing a minimum mean-square-error (MMSE) criterion. However, the dependence of MSE on the noise-free signal makes MSE computation infeasible in practical scenarios. We circumvent the problem by adopting an MSE estimation approach. The ground-truth-independent estimates of MSE are Stein’s unbiased risk estimate (SURE), Poisson unbiased risk estimate (PURE) and Chi-square unbiased risk estimate (CURE) for AWGN, Poison and Chi-square noise models, respectively. The denoising function is optimized to achieve maximum noise suppression by minimizing the MSE estimates. We have chosen the bilateral filter as the denoising function. Bilateral filter is a nonlinear edge-preserving smoother. The performance of the bilateral filter is governed by the choice of its parameters, which can be optimized to minimize the MSE or its estimate. However, in practical scenarios, MSE cannot be computed due to inaccessibility of the noise-free image. We derive SURE, PURE, and CURE in the context of bilateral filtering and compute the parameters of the bilateral filter that yield the minimum cost (SURE/PURE/CURE). On processing the noisy input with bilateral filter whose optimal parameters are chosen by minimizing MSE estimates (SURE/PURE/CURE), we obtain the estimate closest to the ground truth. We denote the bilateral filter with optimal parameters as SURE-optimal bilateral filter (SOBF), PURE-optimal bilateral filter (POBF) and CURE-optimal bilateral filter (COBF) for AWGN, Poisson and Chi-Squared noise scenarios, respectively. In addition to the globally optimal bilateral filters (SOBF and POBF), we propose spatially adaptive bilateral filter variants, namely, SURE-optimal patch-based bilateral filter (SPBF) and PURE-optimal patch-based bilateral filter (PPBF). SPBF and PPBF yield significant improvements in performance and preserve edges better when compared with their globally-optimal counterparts, SOBF and POBF, respectively. We also propose the SURE-optimal multiresolution bilateral filter (SMBF) where we couple SOBF with wavelet thresholding. For Poisson noise suppression, we propose PURE-optimal multiresolution bilateral filter (PMBF), which is the Poisson counterpart of SMBF. We com-pare the performance of SMBF and PMBF with the state-of-the-art denoising algorithms for AWGN and Poisson noise, respectively. The proposed multiresolution-based bilateral filtering techniques yield denoising performance that is competent with that of the state-of-the-art techniques.

The JPEG codec is currently the most widely used image format. This work deals with the design and implementation of an alternative JPEG codec using proximal algorithms in combination with the fixation of points from the original image to suppression of artifacts created in common JPEG coding. To solve the problem, the prox_TV and then the Douglas-Rachford algorithm were used, for which special functions using l_1-norm for image reconstruction were derived. The results of the proposed solution are very good because they can effectively suppress the artefacts created and the result corresponds to the image with a higher set qualitative factor. The proposed method achieves very good results for both simple images and photos, but in the case of large images (1024 × 1024 px) and larger, a large amount of computing time is required, so the method is more suitable for smaller images.

No description available.