Cette thèse est une contribution à l'étude de composés semiconducteurs InX Al1-X N à forte teneur en Indium. Ces composés présentent des propriétés très intéressantes pour des applications dans le domaine de l'amplification des hyperfréquences. L'objectif principal de la thèse est de définir des hétéro-structures de type AlGaInN / GaN, pour transistors à Effet de Champ Piézoélectrique (HEMT), épitaxiées sur substrats de saphir, silicium, et SiC, optimisées en vue de l'amplification hyperfréquence. Dans la première partie, nous étudions la croissance épitaxiale de couches minces du composé binaire GaN, en phase vapeur, à partir de précurseurs organométalliques (MOVPE), dans des conditions optimisées pour obtenir des couches fortement résistives. La deuxième partie est consacrée à l'étude de structures HEMT AlGaN/GaN sur SiC et sur silicium. Sur SiC, nous montrons la forte influence des propriétés du substrat sur les propriétés électriques des structures HEMT. Nous avons étudié une structure nouvelle incluant une fine couche de AlN entre les couches AlGaN et GaN et évalué les performances de transistors HEMT AlGaN/GaN et AlGaN/AlN/GaN sur SiC et sur Silicium (111). La partie suivante est consacrée à la croissance de composés ternaires InAlN. Nous avons étudié l'influence de la température de croissance et du rapport V/III sur les propriétés structurales de InAlN. Les conditions optimales ont été utilisées pour la réalisation de structures HEMT InAlN/AlN/GaN. Nous démontrons l'influence considérable de la couche AlN sur les propriétés électriques de ces structures. Enfin, nous discutons les performances obtenues sur des transistors à effet de champ InAlN/AlN/GaN sur SiC / This work reports on the metal-organic vapor phase epitaxy and on the characterisation of III-N GaInAlN heterostructures for High Electron Mobility Transistors. In a first part, the heteroepitaxy of semiinsulating GaN layers on sapphire, SiC and silicon is presented as the basis for the subsequent growth of III-N HEMT structures. The influence of suitable nucleation layers on the properties of GaN is presented and discussed. A second part deals with AlGaN/GaN HEMT structures grown on SiC and on Si (111) wafers. The influence of SiC substrate properties on the electrical performances of AlGaN/GaN HEMT is presented. A novel structure, including a thin AlN interlayer between the GaN buffer layer and the AlGaN barrier layer has also been introduced. The section is completed by device results obtained on selected heterostructures. A study of the impact of selected growth parameter (i.e. growth temperature, V/III ratio) on the structural and surface properties of InAlN layers is then presented. The optimized conditions have been used for the growth InAlN/AlN/GaN HEMT structures which have been thoroughly characterized. The electrical properties of the structures were found to be strongly dependent on the growth conditions of the AlN interlayer (e.g. deposition time, V/III ratio). Finally, state of the art device results obtained with InAlN/AlN/GaN heterostructures are presented

No description available.

No description available.

Group III-nitride semiconductors are well suited for the fabrication of devices including visible-ultraviolet light emitting diodes, high-temperature and high-frequency devices. The wurtzite III-nitride based heterostructures grown along polar c-direction have large internal electric fields due to discontinuities in spontaneous and piezoelectric polarizations. For optoelectronic devices, such as light-emitting diodes and laser diodes, the internal electric field is deleterious as it causes a spatial separation of electron and hole wave functions in the quantum wells, which decreases emission efficiency. Growth of GaN-based heterostructures in alternative orientations, which have reduced (semipolar) or no polarization (nonpolar) in the growth direction, has been a major area of research in the last few years. The correlation between structural, optical and transport properties of semipolar and nonpolar III-nitride would be extremely useful. The thesis focuses on the growth and characterizations of semipolar and nonpolar III-nitride heterostructures by plasma-assisted molecular beam epitaxy. Chapter 1 provides a brief introduction to the III-nitride semiconductors. The importance of semipolar and nonpolar III-nitride heterostructures over conventional polar heterostructures has been discussed. Chapter 2 deals with the descriptions of molecular beam epitaxy system and working principles of different characterization tools used in the present work. Chapter 3 addresses the molecular beam epitaxial growth of nonpolar (1 1 -2 0) and semipolar (1 1 -2 2) GaN on sapphire substrates. An in-plane orientation relationship is found to be [0 0 0 1] GaN || [-1 1 0 1] sapphire and [-1 1 0 0] GaN || [1 1 -2 0] sapphire for nonpolar GaN on r-sapphire substrates. Effect of growth temperature on structural, morphological and optical properties of nonpolar GaN has been studied. The growth temperature plays a major role in controlling crystal quality, morphology and emission properties of nonpolar a-plane GaN. The a-plane GaN shows crystalline anisotropy nature and it has reduced with increase in the growth temperature. The surface roughness was found to decrease with increase in growth temperature and film grown at 760°C shows reasonably smooth surface with roughness 3.05 nm. Room temperature photoluminescence spectra show near band emission peak at 3.434 -3.442 eV. The film grown at 800 ºC shows broad yellow luminescence peak at 2.2 eV. Low temperature photoluminescence spectra show near band emission at 3.483 eV along with defect related emissions. Raman spectra exhibit blue shift due to compressive strain in the film. An in-plane orientation relationship is found to be [1 -1 00] GaN || [1 2-1 0] sapphire and [-1 -1 2 3] GaN || [0 0 0 1] sapphire for semipolar GaN on m-plane sapphire substrates. The surface morphology of semipolar GaN film is found to be reasonably smooth with pits on the surface. Room temperature photoluminescence shows the near band emission (NBE) at 3.432 eV, which is slightly blue shifted compared to the bulk GaN. The Raman E2 (high) peak position observed at 569.1 cm1. Chapter 4 deals with the fabrication and characterizations of Au/nonpolar and Au/semipolar GaN schottky diodes. The temperature-dependent current–voltage measurements have been used to determine the current mechanisms in Schottky diodes fabricated on nonpolar a-plane GaN and semipolar GaN epilayers. The barrier height (φb) and ideally factor (η) estimated from the thermionic emission model are found to be temperature dependent in nature indicate the deviations from the thermionic emission (TE) transport mechanism. Low temperature I-V characteristics of Au/ GaN Schottky diode show temperature independent tunnelling parameter. Barrier heights calculated from XPS are found to be 0.96 eV and 1.13 eV for Au/nonpolar GaN and Au/semipolar GaN respectively. Chapter 5 demonstrates the growth of InN on r-sapphire substrates with and without GaN buffer layer. InN film and nanostructures are grown on r-sapphire without GaN buffer layer and they are highly oriented along (0002) direction. The electron microscopy study confirms the nanostructures are vertically aligned and highly oriented along the (0001) direction. The Raman studies of InN nanostructures show the SO modes along with the other possible Raman modes. The band gap of InN nanostructures is found to be 0.82 eV. InN grown with a-plane GaN buffer shows nonpolar orientated growth. Growth temperature dependent studies of nonpolar a-plane InN epilayers are carried out. The valence band offset value is calculated to be 1.31 eV for nonpolar a-plane InN/GaN heterojunctions. The heterojunctions form in the type-I straddling configuration with a conduction band offsets of 1.41 eV. Chapter 6 deals with the temperature dependent I-V characteristics of the nonpolar a-plane (1 1 -2 0) InN/GaN heterostructures. The measured values of barrier height and ideality factor from the TE model show the temperature dependent variation. The double Gaussian distribution has mean barrier height values ( ϕb ) of 1.17 and 0.69 eV with standard deviation (σs ) of 0.17 and 0.098 V, respectively. The modified Richardson plot ln (Is/T2)-q2σ2/2k2T2 ) versus q/kT in the temperature range of 350 – 500 K, yielded the Richardson constant of 19.5 A/cm2 K2 which is very close to the theoretical value of 24 A/cm2 K2 for n-type GaN. The tunneling parameters E0 found to be temperature independent at low temperature range (150 –300 K). Chapter 7 concludes with the summary of present investigations and the scope for future work.

Ce travail de thèse est une contribution à l'étude des propriétés de spin dans les semiconducteurs par spectroscopie de photoluminescence et par photoconductivité en vue d’applications possibles dans le domaine de l’électronique du spin.Nous avons analysé les propriétés de spin des électrons de conduction dans les matériaux semiconducteurs nitrures dilués, massif et puits quantiques (GaAsN, GaAsN/GaAs). Nous avons étudié le mécanisme de recombinaison dépendante du spin des électrons de conduction sur les centres paramagnétiques induits par l’introduction d’azote dans GaAs. Nous avons mis en évidence l’effet de « filtrage » de spin des électrons de conduction que ce mécanisme peut induire ; en particulier, nous avons mené des études détaillées en fonction de la concentration d’azote, de la puissance excitatrice, d’un champ magnétique externe et, pour les hétérostructures, de l’épaisseur des puits quantiques. L’origine chimique des centres paramagnétiques a été, de plus, identifiée par des études de résonance paramagnétique détectée optiquement (ODMR).Nous avons également complété ces études purement optiques sur la recombinaison dépendante du spin, par des expériences de photoconductivité en vue d’applications possibles liées à l’électronique du spin. Nous avons montré que la photoconductivité des matériaux nitrures dilués peut être contrôlée par la polarisation de la lumière incidente. Un détecteur électrique de la polarisation de la lumière à base de GaAsN a été ainsi fabriqué et testé.Ces résultats ont été également interprétés et simulés grâce à un système d’équations dynamiques pouvant rendre compte à la fois des résultats de photoluminescence et de transport / This thesis work is a contribution to the investigation of the spin properties of semiconductors by photoluminescence and photoconductivity spectroscopy with the aim of future applications in the spintronic field. We have studied the conduction band electron spin properties of dilute nitride semiconductors in epilayers and quantum wells (GaAsN, GaAsN/GaAs). In particular, we have investigated the spin dependent recombination of conduction band electrons on deep paramagnetic centers induced by the introduction of nitrogen into GaAs. We have also evidenced the “spin filtering” effect made possible by this spin dependent recombination mechanism. More precisely, we have carried out a systematic study of the spin filtering effect as a function of the nitrogen concentration, excitation power, external magnetic field and, for the hetero-structures, as well as a function of the quantum well thickness. The chemical origin of the deep paramagnetic centers has been also determined by optically detected magnetic resonance (ODMR). We have completed these all-optical studies on the spin dependent recombination by photoconductivity experiments in order to demonstrate a “proof of concept” system for spintronic applications. We have shown that the photoconductivity in dilute nitride semiconductors can be controlled by the polarization of the incident light: an electrical detector of the light polarization has therefore been built. These results have been as well modeled thanks to a rate equation system able to reproduced both the photoluminescence and photoconductivity experimental results

The present work has been focused on the growth of Group III-nitride epitaxial layers and nanostructures on Si (111) substrates by plasma-assisted molecular beam epitaxy. Silicon is regarded as a promising substrate for III-nitrides, since it is available in large quantity, at low cost and compatible to microelectronics device processing. However, three-dimensional island growth is unavoidable for the direct growth of GaN on Si (111) because of the extreme lattice and thermal expansion coefficient mismatch. To overcome these difficulties, by introducing β-Si3N4 buffer layer, the yellow luminescence free GaN can be grow on Si (111) substrate. The overall research work carried out in the present study comprises of five main parts. In the first part, high quality, crack free and smooth surface of GaN and InN epilayers were grown on Si(111) substrate using the substrate nitridation process. Crystalline quality and surface roughness of the GaN and InN layers are extremely sensitive to nitridation conditions such as nitridation temperature and time. Raman and PL studies indicate that the GaN film obtained by the nitridation sequences has less tensile stress and optically good. The optical band gaps of InN are obtained between ~0.73 to 0.78 eV and the blueshift of absorption edge can be induced by background electron concentration. The higher electron concentration brings in the larger blueshift, due to a possible Burstein–Moss effect. InN epilayers were also grown on GaN/Si(111) substrate by varying the growth parameters such as indium flux, substrate temperature and RF power. In the second part, InGaN/Si, GaN/Si3N4/n-Si and InN/Si3N4/n-Si heterostructures were fabricated and temperature dependent electrical transport behaviors were studied. Current density-voltage plots (J-V-T) of InGaN/Si heterostructure revealed that the ideality factor and Schottky barrier height are temperature dependent and the incorrect values of the Richardson’s constant produced, suggests an inhomogeneous barrier at the heterostructure interface. The higher value of the ideality factor compared to the ideal value and its temperature dependence suggest that the current transport is primarily dominated by thermionic field emission rather than thermionic emission. The valence band offset of GaN/β-Si3N4/Si and InGaN/Si heterojunctions were determined by X-ray photoemission spectroscopy. InN QDs on Si(111) substrate by droplet epitaxy and S-K growth method were grown in the third part. Single-crystalline structure of InN QDs (droplet epitaxy) was verified by TEM and the chemical bonding configurations of InN QDs were examined by XPS. The interdigitated electrode pattern was created and (I-V) characteristics of InN QDs were studied in a metal–semiconductor–metal configuration in the temperature range of 80–300 K. The I-V characteristics of lateral grown InN QDs were explained by using the trap model. A systematic manipulation of the morphology, optical emission and structural properties of InN/Si (111) QDs (S-K method) is demonstrated by changing the growth kinetics parameters such as flux rate and growth time. The growth kinetics of the QDs has been studied through the scaling method and observed that the distribution of dot sizes, for samples grown under varying conditions, has followed the scaling function. In the fourth part, InN nanorods (NRs) were grown on Si(111) and current transport properties of NRs/Si heterojunctions were studied. The rapid rise and decay of infrared on/off characteristics of InN NRs/Si heterojunction indicate that the device is highly sensitive to the IR light. Self-aligned GaN nanodots were grown on semi-insulating Si(111) substrate. The interdigitated electrode pattern was created on nanodots using photolithography and dark as well as UV photocurrent were studied. Surface band gaps of InN QDs were estimated from scanning tunneling spectroscopy (STS) I-V curves in the last part. It is found that band gap is strongly dependent on the size of InN QDs. The observed size-dependent STS band gap energy blueshifts as the QD’s diameter or height was reduced.

Through the history of mankind, novel materials have played a key role in techno- logical progress. As we approach the limits of scaling it becomes difficult to squeeze out any more extensions to Moore’s law by just reducing device feature sizes. It is important to look for an alternate semiconductor to silicon in order to continue making the progress predicted by Moore’s law. Among the various semiconductor options being explored world-wide, the III-nitride semiconductor material system has certain unique characteristics that make it one of the leading contenders. We explore the III-nitride semiconductor material system for the unique advantages that it offers over the other alternatives available to us. This thesis studies the device applications of epitaxial III-nitride films and nanos- tructures grown using plasma assisted molecular beam epitaxy (PAMBE) The material characterisation of the PAMBE grown epitaxial III-nitrides was car- ried out using techniques like high resolution X-ray diffraction (HR-XRD), field emis- sion scanning electron microscopy (FESEM), room temperature photoluminescence (PL) and transmission electron microscopy (TEM). The epitaxial III-nitrides were then further processed to fabricate devices like Schottky diodes, photodetectors and surface acoustic wave (SAW) devices. The electrical charcterisation of the fabricated devices was carried out using techniques like Hall measurement, IV and CV measure- ments on a DC probe station and S-parameter measurements on a vector network analyser connected to an RF probe station. We begin our work on Schottky diodes by explaining the motivation for adding an interfacial layer in a metal-semiconductor Schottky contact and how high-k di- electrics like HfO2 have been relatively unexplored in this application. We report the work carried out on the Pt/n-GaN metal-semiconductor (MS) Schottky and the Pt/HfO2/n-GaN metal-insulator-semiconductor (MIS) Schottky diode. We report an improvement in the diode parameters like barrier height (0.52 eV to 0.63 eV), ideality factor (2.1 to 1.3) and rectification ratio (35.9 to 98.9 @2V bias) after the introduction of 5 nm of HfO2 as the interfacial layer. Temperature dependent I-V measurements were done to gain a further understanding of the interface. We observe that the barrier height and ideality factor exhibit a temperature dependence. This was attributed to inhomogeneities at the interface and by assuming a Gaussian distribution of barrier heights. UV and IR photodetectors using III-nitrides are then studied. Our work on UV photodetectors describes the growth of epitaxial GaN films. Au nanoparticles were fabricated on these films using thermal evaporation and annealing. Al nanostruc- tures were fabricated using nanosphere lithography. Plasmonic enhancement using these metallic nanostructures was explored by fabricating metal-semiconductor-metal (MSM) photodetectors. We observed plasmonic enhancement of photocurrent in both cases. To obtain greater improvement, we etched down on the GaN film using reac tive ion etching (RIE). This resulted in further increase in photocurrent along with a reduction in dark current which was attributed to creation of new trap states. IR photodetectors studied in this thesis are InN quantum dots whose density can be controlled by varying the indium flux during growth. We observe that increase in InN quantum dot density results in increase in photocurrent and decrease in dark current in the fabricated IR photodetectors. We then explore the advantages that InGaN offers as a material that supports surface acoustic waves and fabricate InGaN based surface acoustic wave devices. We describe the growth of epitaxial In0.23 Ga0.77 N films on GaN template using molecular beam epitaxy. Material characterisation was carried out using HR-XRD, FESEM, PL and TEM. The composition was determined from HR-XRD and PL measurements and both results matched each other. This was followed by the fabrication of interdigited electrodes with finger spacing of 10 µm. S-parameter results showed a transmission peak at 104 MHz with an insertion loss of 19 dB. To the best of our knowledge, this is the first demonstration of an InGaN based SAW device. In summary, this thesis demonstrates the practical advantages of epitaxially grown film and nanostructured III-nitride materials such as GaN, InN and InGaN using plasma assisted molecular beam epitaxy for Schottky diodes, UV and IR photodetec- tors and surface acoustic wave devices.

The present work focuses on the growth and characterizations of GaN and InN layers and nanostructures on p-Si(100) and p-Si(111) substrates by plasma-assisted molecular beam epitaxy and the studies of GaN/p-Si and InN/p-Si heterojunctions properties. The thesis is divided in to seven different chapters. Chapter 1 gives a brief introduction on III-nitride materials, growth systems, substrates, possible device applications and technical background. Chapter 2 deals with experimental techniques including the details of PAMBE system used in the present work and characterization tools for III-nitride epitaxial layers as well as nanostructures. Chapter 3 involves the growth of GaN films on p-Si(100) and p-Si(111) substrates. Phase pure wurtzite GaN films are grown on Si (100) substrates by introducing a silicon nitride layer followed by low temperature GaN growth as buffer layers. GaN films grown directly on Si (100) are found to be phase mixtured, containing both cubic and hexagonal modifications. The x-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy studies reveal that the significant enhancement in the structural and optical properties of GaN films grown with silicon nitride buffer layer grown at 800 oC, when compared to the samples grown in the absence of silicon nitride buffer layer and with silicon nitride buffer layer grown at 600 oC. Core-level photoelectron spectroscopy of SixNy layers reveals the sources for superior qualities of GaN epilayers grown with the high temperature substrate nitridation process. The discussion has been carried out on the typical inverted rectification behavior exhibited by n-GaN/p-Si heterojunctions. Considerable modulation in the transport mechanism is observed with the nitridation conditions. The heterojunction fabricated with the sample of substrate nitridation at high temperature exhibites superior rectifying nature with reduced trap concentrations. Lowest ideality factors (~1.5) are observed in the heterojunctions grown with high temperature substrate nitridation which is attributed to the recombination tunneling at the space charge region transport mechanism at lower voltages and at higher voltages space charge limited current conduction is the dominating transport mechanism. Whereas, thermally generated carrier tunneling and recombination tunneling are the dominating transport mechanisms in the heterojunctions grown without substrate nitridation and low temperature substrate nitridation, respectively. A brief comparison of the structural, optical and heterojunction properties of GaN grown on Si(100) and Si(111) has been carried out. Chapter 4 involves the growth and characterizations of InN nanostructures and thinfilms on p-Si(100) and p-Si(111) substrates. InN QDs are grown on Si(100) at different densities. The PL characteristics of InN QDs are studied. A deterioration process of InN QDs, caused by the oxygen incorporation into the InN lattice and formation of In2O3/InN composite structures was established from the results of TEM, XPS and PL studies. The results confirm the partial oxidation of the outer shell of the InN QDs, while the inner core of the QDs remains unoxidized. InN nanorods are grown on p-Si(100), structural characterizations are carried out by SEM, and TEM. InN nanodots are grown on p-Si(100), structural characterizations are performed. InN films were grown on Si(100) and Si(111) substrates and structural characterizations are carried out. Chapter 5 deals with the the heterojunction properties of InN/p-Si(100) and InN/p-Si(111).The transport behavior of the InN NDs/p-Si(100) diodes is studied at various bias voltages and temperatures. The temperature dependent ZB BH and ideality factors of the forward I-V data are observed, while it is governed through the modified Richardson’s plot. The difference in FB BH and C-V BH and the deviation of ideality factor from unity indicate the presence of inhomogeneities at the interface. The band offsets derived from C-V measurements are found to be Δ EC=1.8 eV and Δ EV =1.3 eV, which are in close agreement with Anderson’s model. The band offsets of InN/p-Si heterojunctions are estimated using XPS data. A type-III band alignment with a valence band offset of Δ EV =1.39 eV and conduction band offset of ΔEC=1.81 eV is identified. The charge neutrality level model provides a reasonable description of the band alignment of the InN/p-Si interface. The interface dipole deduced by comparison with the electron affinity model is 0.06 eV. The transport studies of InN NR/p-Si(100) heterojunctions have been carried out by conductive atomic force microscopy (CAFM) as well as conventional large area contacts. Discussion of the electrical properties has been carried out based on local current-voltage (I-V) curves, as well as on the 2D conductance maps. The comparative studies on transport properties of diodes fabricated with InN NRs and NDs grown on p-Si(100) substrates and InN thin films grown on p-Si(111) substrates have also been carried out. Chapter 6 deals with the growth and characterizations of InN/GaN heterostructures on p-Si(100) and p-Si(111) substarets and also on the InN/GaN/p-Si heterojunction properties. The X-ray diffraction (XRD), scanning electron microscopy (SEM) studies reveal a considerable variation in crystalline quality of InN with grown parameters. Deterioration in the rectifying nature is observed in the case of InN/GaN/p-Si(100) heterojunction substrate when compared to InN/GaN/p-Si (111) due to the defect mediated tunneling effect, caused by the high defect concentration in the GaN and InN films grown on Si(100) and also due to the trap centers exist in the interfaces. Reduction in ideality factor is also observed in the case of n-InN/n-GaN/p–Si(111) when compared to n-InN/n-GaN/p–Si(100) heterojunction. The sum of the ideality factors of individual diodes is consistent with experimentally observed high ideality factors of n-InN/n-GaN/p–Si double heterojunctions due to double rectifying heterojunctions and metal semiconductor junctions. Variation of effective barrier heights and ideality factors with temperature are confirmed, which indicate the inhomogeneity in barrier height, might be due to various types of defects present at the GaN/Si and InN/GaN interfaces. The dependence of forward currents on both the voltage and temperatures are explained by multi step tunneling model and the activation energis were estimated to be 25meV and 100meV for n-InN/n-GaN/p–Si(100) and n-InN/n-GaN/p–Si(111) heterojunctions, respectively. Chapter 7 gives the summary of the present study and also discusses about future research directions in this area.

Pour la fabrication des transistors hyperfréquences de puissance à base de nitrures, l’alliage InAlN est considéré comme une meilleure barrière qu’AlGaN grâce à l’accord de maille pour une composition en indium voisine de 18 %. Ainsi le gaz d'électrons à deux dimensions (2DEG) est-il généré seulement par la polarisation spontanée dans une hétérointerface InAlN/GaN sans contrainte résiduelle pour une fabrication de transistors aux performances optimales. Cependant, durant sa croissance sur GaN, sa qualité cristalline se dégrade avec l’épaisseur et il se forme des défauts V au niveau de l’interface. Afin de déterminer les sources de ce comportement, nous avons mené une étude théorique par dynamique moléculaire et techniques ab initio pour analyser la stabilité et les propriétés des alliages des composés nitrures en nous focalisant particulièrement sur InAlN. L’analyse des diagrammes de phase a permis de montrer que cet alliage présente une large gamme d’instabilité en composition d’indium et un comportement différent d’InGaN sous compression avec une instabilité amplifiée sous forte pression. En déterminant la stabilité énergétique de la lacune d’azote en interaction avec l’indium, nous avons montré que ce défaut ponctuel autour duquel des atomes d’indium tendent à retrouver une longueur de liaison voisine de celle dans InN pouvait être un catalyseur pour la formation de clusters dans cet alliage. Ces clusters d’InN introduisent des niveaux donneurs profonds dans la bande interdite. En ce qui concerne les dislocations traversantes, nos résultats montrent qu’elles auront aussi tendance à capturer des atomes d’indium dans leur cœur pour minimiser leur énergie. Ainsi nous avons pu apporter les bases théoriques qui montrent que la lacune d’azote participe à la dégradation spontanée des couches d’InAlN et que les dislocations traversantes sont amenées à y participer en attirant les atomes d’indium et donc en renforçant la séparation de phase en leur voisinage. / For the fabrication of nitride-based power microwave transistors, the InAlN alloy is considered to be a better barrier than AlGaN thanks to the lattice match with GaN for an indium composition around 18%. Thus the two-dimensional electron gas (2DEG) is generated only by the spontaneous polarization at the AlInN/GaN heterointerface for a production of highest performance transistors. However, during its growth on GaN, its crystalline quality deteriorates with the thickness and V-defects are formed at the layer surface. To determine the sources of this behavior, we carried out a theoretical study by molecular dynamics and ab initio techniques to analyze the stability and the properties of alloys of nitride compounds, focusing particularly on InAlN. The analysis of the phase diagrams showed that this alloy has a wide zone of instability versus the indium composition and a different behavior with InGaN with amplified instability under high compressive strain. By determining the energetic stability of the nitrogen vacancy could be catalyst for forming clusters in this alloy. These InN clusters introduce deep donor levels inside the band gap. With regard to treading dislocations, our results show that they will also tend to capture indium atoms in their cores in order to minimize their energy. Thus, we have been able to provide a theoretical basis that show that the nitrogen vacancy participates in the spontaneous degradation of the AlInN layers and that the threading dislocations participate by attracting the indium atoms and thus reinforcing the separation of phase in their vicinity.

Group III-nitride semiconductors have received much research attention and witnessed a significant development due to their ample applications in solid-state lighting and high-power/high-frequency electronics. Numerous growth methods were explored to achieve device quality epitaxial III-nitride semiconductors. Among the growth methods for III-nitride semiconductors, molecular beam epitaxy provides advantages such as formation of abrupt interfaces and in-situ monitoring of growth. The present research work focuses on the growth and characterizations of III-nitride based epitaxial films, nanostructures and heterostructures on c-sapphire substrate using plasma-assisted molecular beam epitaxy system. The correlation between structural, optical and electrical properties of III-nitride semiconductors would be extremely useful. The interfaces of the metal/semiconductor and semiconductor heterostructures are very important in the performance of semiconductor devices. In this regard, the electrical transport studies of metal/semiconductor and semiconductor heterostructures have been carried out. Besides, studies involved with the defect induced room temperature ferromagnetism of GaN films and InN nano-structures have also been carried out. The thesis is organized in eight different chapters and a brief overview of each chapter is given below. Chapter 1 provides a brief introduction on physical properties of group III-nitride semiconductors. It also describes the importance of III-nitride heterostructures in the operation of optoelectronic devices. In addition, it also includes the current strategy of the emergence of room temperature ferromagnetism in III-nitride semiconductors. Chapter 2 deals with the basic working principles of molecular beam epitaxy system and different characterization tools employed in the present work. Chapter 3 describes the growth of GaN films on c-sapphire by plasma-assisted molecular beam epitaxy. The effects of N/Ga flux ratio on structural, morphological and optical properties have been studied. The flux ratio plays a major role in controlling crystal quality, morphology and emission properties of GaN films. The dislocation density is found to increase with increase in N/Ga flux ratio. The surface morphologies of the films as seen by scanning electron microscopy show pits on the surface and found that the pit density on the surface increases with flux ratio. The room temperature photoluminescence study reveals the shift in band-edge emission towards the lower energy with increase in N/Ga flux ratio. This is believed to arise from the reduction in compressive stress in the GaN films as it is evidenced by room temperature Raman study. The transport studies on the Pt/GaN Schottky diodes showed a significant increase in leakage current with an increase in N/Ga ratio and is found to be caused by the increase in dislocation density in the GaN films. Chapter 4 deals with the fabrication and characterization of Au/GaN Schottky diodes. The temperature dependent current–voltage measurements have been used to determine the current transport mechanism in Schottky diodes. The barrier height (φb) and the ideality factor (η) are estimated from the thermionic emission model and are found to be temperature dependent in nature, indicating the existence of barrier height inhomogeneities at the Au/GaN interface. The conventional Richardson plot of ln(Is/T2) versus 1/kT gives Richardson constant value of 3.23×10-5 Acm-2 K-2, which is much lower than the known value of 26.4 Acm-2 K-2 for GaN. Such discrepancy of Richardson constant value was attributed to the existence of barrier height inhomogeneities at the Au/GaN interface. The modified Richardson plot of ln(Is/T2)-q2σs2/2k2T2 versus q/kT, by assuming a Gaussian distribution of barrier heights at the Au/GaN interface, provides the Schottky barrier height of 1.47 eV and Richardson constant value of 38.8 Acm-2 K-2 which is very close to the theatrical value of Richardson constant. The temperature dependence of barrier height is interpreted on the basis of existence of the Gaussian distribution of the barrier heights due to the barrier height inhomogeneities at the Au/GaN interface. Chapter 5 addresses on the influence of GaN underlayer thickness on structural, electrical and optical properties of InN thin films grown using plasma-assisted molecular beam epitaxy. The high resolution X-ray diffraction study reveals superior crystalline quality for the InN film grown on thicker GaN film. The electronic and optical properties seem to be greatly influenced by the structural quality of the films, as can be evidenced from Hall measurement and optical absorption spectroscopy. Also, we present the studies involving the dependence of structural, electrical and optical properties of InN films, grown on thicker GaN films, on growth temperature. The optical absorption edge of InN film is found to be strongly dependent on carrier concentration. Kane’s k.p model is used to describe the dependence of optical absorption edge on carrier concentration by considering the non-parabolic dispersion relation for carrier in the conduction band. Chapter 6 deals with the analysis of the temperature dependent current transport mechanisms in InN/GaN heterostructure based Schottky junctions. The barrier height (φb) and the ideality factor (η) of the InN/GaN Schottky junctions are found to be temperature dependent. The temperature dependence of the barrier height indicates that the Schottky barrier height is inhomogeneous in nature at the heterostructure interface. The higher value of the ideality factor and its temperature dependence suggest that the current transport is primarily dominated by thermionic field emission (TFE) other than thermionic emission (TE). The room temperature barrier height and the ideality factor obtained by TFE model are 1.43 eV and 1.21, respectively. Chapter 7 focuses on the defect induced room temperature ferromagnetism in Ga deficient GaN epitaxial films and InN nano-structures grown on c-sapphire substrate by using plasma-assisted molecular beam epitaxy. The observed yellow emission peak in room temperature photoluminescence spectra and the peak positioning at 300 cm-1 in Raman spectra confirms the existence of Ga vacancies in GaN films. The ferromagnetism in Ga deficient GaN films is believed to originate from the polarization of the unpaired 2p electrons of nitrogen surrounding the Ga vacancy. The InN nano-structures of different size are grown on sapphire substrate, the structural and magnetic properties are studied. The room temperature magnetization measurement of InN nano-structures exhibits the ferromagnetic behavior. The saturation magnetization is found to be strongly dependent on the size of the nano-structures. Finally, Chapter 8 gives the summary of the present work and the scope for future work in this area of research.