The goal of this thesis is to work out an introduction to the chip packaging and decapsulation. Further can be found a description of a method leading to dacapsulate concrete chips. Final part is devoted to getting chip pictures using microscope and analysis of the pictures afterwards.

Die umfassende Beobachtbarkeit von System‐on‐Chips (SoCs) ist eine wichtige Voraussetzung für das effiziente Testen und Debuggen eingebetteter Systeme. Ausgehend von einer Analyse verschiedener Anwendungsfälle ergibt sich ein Katalog von Anforderungen an die Beobachtbarkeit von SoCs. Ein wichtiges Kriterium ist hier die Vollständigkeit der Beobachtung und umfasst die Aktivitäten der CPU (ausgeführte Instruktionen, gelesene und geschriebene Daten, Verhalten des Caches, Ausführungszeiten), des Bussystems und von Umgebungsbedingungen. Weitere Kriterien sind die Echtzeitfähigkeit und die Kontinuität der Beobachtung sowie die gleichzeitige Durchführung verschiedener Beobachtungsaufgaben. Dabei soll es zu einer möglichst geringen Beeinflussung des SoCs kommen. Weitere wichtige Aspekt sind die Kosten der Lösung, die Universalität, die Skalierbarkeit sowie die Latenz der Verfügbarkeit der Beobachtungsergebnisse. Für viele Anwendungen, besonders in sicherheitskritischen Bereichen, muss zudem nachgewiesen werden, dass das Beobachtungsverfahren kein Fehlverhalten des SoCs bewirkt bzw. ein solches maskiert. Eine besondere Herausforderung stellen Multiprozessor‐SoCs (MPSoCs) dar, da hier die Kommunikation zwischen den einzelnen CPUs im Inneren des SoC stattfindet und entsprechend schwierig für einen externen Bobachter sichtbar zu machen ist. Der Stand der Technik zur Beobachtung von SoCs wird im Wesentlichen durch zwei Verfahren dargestellt. Bei der Software‐Instrumentierung wird zum funktionalen Programmcode zusätzlicher Code hinzugefügt, welcher zur Beobachtung des Programms dient. Diese Methode ist einfach und universell anwendbar, erfüllt aber die genannten Kriterien nur sehr eingeschränkt. Nachteilig ist hier der Ressourcenverbrauch im Falle des Verbleibs der Instrumentierung im fertigen Produkt. Wird die Instrumentierung nur temporär dem Code hinzugefügt, muss sichergestellt werden, dass das Beobachtungsergebnis auch für den finalen Code anwendbar ist – was besonders bei ressourcen‐abhängigen Integrationstests nur schwierig erfüllbar ist. Eine alternative Lösung stellt eine spezielle Hardware‐Unterstützung in SoCs („embedded Trace“) dar. Hier werden im SoC Zustandsinformationen (z.B. Taskwechsel, ausgeführte Instruktionen, Datentransfers) gesammelt und mittels Trace‐Nachrichten an den Beobachter übermittelt. Dabei stellt die Bandbreite, die zur Ausgabe der Trace‐Nachrichten vom SoC verfügbar ist, ein entscheidendes Nadelöhr dar ‐ im SoC sind viel mehr den Beobachter interessierende Informationen verfügbar als nach außen transferiert werden können. Damit haben beide dem gegenwärtige Stand der Technik entsprechende Beobachtungsverfahren eine Reihe von Einschränkungen, die sich besonders bei der Vollständigkeit der Beobachtung, der Flexibilität, der Kontinuität und der Unterstützung von MPSoCs zeigen. In dieser Arbeit wird nun ein neuer Ansatz vorgestellt, welcher gegenüber dem Stand der Technik in einigen Bereichen deutliche Verbesserungen bietet. Dabei werden die Trace‐Daten nicht vom zu beobachtenden SoC direkt, sondern aus einer parallel mitlaufenden Emulation gewonnen. Die Bandbreite der für die Synchronisation der Emulation erforderlichen Daten ist in vielen Fällen deutlich geringer als bei der Ausgabe von umfassenden Trace‐Nachrichten mittels „embedded Trace“‐Lösungen. Gleichzeitig ist eine vollständige, äußerst detaillierte Beobachtung der Vorgänge innerhalb des SoC möglich. Das neue Beobachtungsverfahren wurde mittels verschiedener FPGA-basierter Implementierungen evaluiert, hier konnte auch die Anwendbarkeit für MPSoCs gezeigt werden.

[ES] Los procesadores multinúcleo actuales cuentan con recursos compartidos entre los diferentes núcleos. Dos de estos recursos compartidos, la cache de último nivel y el ancho de banda de memoria principal, pueden convertirse en cuellos de botella para el rendimiento. Además, con el crecimiento del número de núcleos que implementan los diseños más recientes, la red dentro del chip también se convierte en un cuello de botella que puede afectar negativamente al rendimiento, ya que las redes tradicionales pueden encontrar limitaciones a su escalabilidad en el futuro cercano. Prácticamente la totalidad de los diseños actuales implementan jerarquías de memoria que se comunican mediante rápidas redes de interconexión. Esta organización es eficaz dado que permite reducir el número de accesos que se realizan a memoria principal y la latencia media de acceso a memoria. Las caches, la red de interconexión y la memoria principal, conjuntamente con otras técnicas conocidas como la prebúsqueda, permiten reducir las enormes latencias de acceso a memoria principal, limitando así el impacto negativo ocasionado por la diferencia de rendimiento existente entre los núcleos de cómputo y la memoria. Sin embargo, compartir los recursos mencionados es fuente de diferentes problemas y retos, siendo uno de los principales el manejo de la interferencia entre aplicaciones. Hacer un uso eficiente de la jerarquía de memoria y las caches, así como contar con una red de interconexión apropiada, es necesario para sostener el crecimiento del rendimiento en los diseños tanto actuales como futuros. Esta tesis analiza y estudia los principales problemas e inconvenientes observados en estos dos recursos: la cache de último nivel y la red dentro del chip. En primer lugar, se estudia la escalabilidad de las tradicionales redes dentro del chip con topología de malla, así como esta puede verse comprometida en próximos diseños que cuenten con mayor número de núcleos. Los resultados de este estudio muestran que, a mayor número de núcleos, el impacto negativo de la distancia entre núcleos en la latencia puede afectar seriamente al rendimiento del procesador. Como solución a este problema, en esta tesis proponemos una de red de interconexión óptica modelada en un entorno de simulación detallado, que supone una solución viable a los problemas de escalabilidad observados en los diseños tradicionales. A continuación, esta tesis dedica un esfuerzo importante a identificar y proponer soluciones a los principales problemas de diseño de las jerarquías de memoria actuales como son, por ejemplo, el sobredimensionado del espacio de cache privado, la existencia de réplicas de datos y rigidez e incapacidad de adaptación de las estructuras de cache. Aunque bien conocidos, estos problemas y sus efectos adversos en el rendimiento pueden ser evitados en procesadores de alto rendimiento gracias a la enorme capacidad de la cache de último nivel que este tipo de procesadores típicamente implementan. Sin embargo, en procesadores de bajo consumo, no existe la posibilidad de contar con tales capacidades y hacer un uso eficiente del espacio disponible es crítico para mantener el rendimiento. Como solución a estos problemas en procesadores de bajo consumo, proponemos una novedosa organización de jerarquía de dos niveles cache que utiliza una red de interconexión óptica. Los resultados obtenidos muestran que, comparado con diseños convencionales, el consumo de energía estática en la arquitectura propuesta es un 60% menor, pese a que los resultados de rendimiento presentan valores similares. Por último, hemos extendido la arquitectura propuesta para dar soporte tanto a aplicaciones paralelas como secuenciales. Los resultados obtenidos con la esta nueva arquitectura muestran un ahorro de hasta el 78 % de energía estática en la ejecución de aplicaciones paralelas. / [CA] Els processadors multinucli actuals compten amb recursos compartits entre els diferents nuclis. Dos d'aquests recursos compartits, la memòria d’últim nivell i l'ample de banda de memòria principal, poden convertir-se en colls d'ampolla per al rendiment. A mes, amb el creixement del nombre de nuclis que implementen els dissenys mes recents, la xarxa dins del xip també es converteix en un coll d'ampolla que pot afectar negativament el rendiment, ja que les xarxes tradicionals poden trobar limitacions a la seva escalabilitat en el futur proper. Pràcticament la totalitat dels dissenys actuals implementen jerarquies de memòria que es comuniquen mitjançant rapides xarxes d’interconnexió. Aquesta organització es eficaç ates que permet reduir el nombre d'accessos que es realitzen a memòria principal i la latència mitjana d’accés a memòria. Les caches, la xarxa d’interconnexió i la memòria principal, conjuntament amb altres tècniques conegudes com la prebúsqueda, permeten reduir les enormes latències d’accés a memòria principal, limitant així l'impacte negatiu ocasionat per la diferencia de rendiment existent entre els nuclis de còmput i la memòria. No obstant això, compartir els recursos esmentats és font de diversos problemes i reptes, sent un dels principals la gestió de la interferència entre aplicacions. Fer un us eficient de la jerarquia de memòria i les caches, així com comptar amb una xarxa d’interconnexió apropiada, es necessari per sostenir el creixement del rendiment en els dissenys tant actuals com futurs. Aquesta tesi analitza i estudia els principals problemes i inconvenients observats en aquests dos recursos: la memòria cache d’últim nivell i la xarxa dins del xip. En primer lloc, s'estudia l'escalabilitat de les xarxes tradicionals dins del xip amb topologia de malla, així com aquesta es pot veure compromesa en propers dissenys que compten amb major nombre de nuclis. Els resultats d'aquest estudi mostren que, a major nombre de nuclis, l'impacte negatiu de la distància entre nuclis en la latència pot afectar seriosament al rendiment del processador. Com a solució' a aquest problema, en aquesta tesi proposem una xarxa d’interconnexió' òptica modelada en un entorn de simulació detallat, que suposa una solució viable als problemes d'escalabilitat observats en els dissenys tradicionals. A continuació, aquesta tesi dedica un esforç important a identificar i proposar solucions als principals problemes de disseny de les jerarquies de memòria actuals com son, per exemple, el sobredimensionat de l'espai de memòria cache privat, l’existència de repliques de dades i la rigidesa i incapacitat d’adaptació' de les estructures de memòria cache. Encara que ben coneguts, aquests problemes i els seus efectes adversos en el rendiment poden ser evitats en processadors d'alt rendiment gracies a l'enorme capacitat de la memòria cache d’últim nivell que aquest tipus de processadors típicament implementen. No obstant això, en processadors de baix consum, no hi ha la possibilitat de comptar amb aquestes capacitats, i fer un us eficient de l'espai disponible es torna crític per mantenir el rendiment. Com a solució a aquests problemes en processadors de baix consum, proposem una nova organització de jerarquia de dos nivells de memòria cache que utilitza una xarxa d’interconnexió òptica. Els resultats obtinguts mostren que, comparat amb dissenys convencionals, el consum d'energia estàtica en l'arquitectura proposada és un 60% menor, malgrat que els resultats de rendiment presenten valors similars. Per últim, hem estes l'arquitectura proposada per donar suport tant a aplicacions paral·leles com seqüencials. Els resultats obtinguts amb aquesta nova arquitectura mostren un estalvi de fins al 78 % d'energia estàtica en l’execució d'aplicacions paral·leles. / [EN] Current multicores face the challenge of sharing resources among the different processor cores. Two main shared resources act as major performance bottlenecks in current designs: the off-chip main memory bandwidth and the last level cache. Additionally, as the core count grows, the network on-chip is also becoming a potential performance bottleneck, since traditional designs may find scalability issues in the near future. Memory hierarchies communicated through fast interconnects are implemented in almost every current design as they reduce the number of off-chip accesses and the overall latency, respectively. Main memory, caches, and interconnection resources, together with other widely-used techniques like prefetching, help alleviate the huge memory access latencies and limit the impact of the core-memory speed gap. However, sharing these resources brings several concerns, being one of the most challenging the management of the inter-application interference. Since almost every running application needs to access to main memory, all of them are exposed to interference from other co-runners in their way to the memory controller. For this reason, making an efficient use of the available cache space, together with achieving fast and scalable interconnects, is critical to sustain the performance in current and future designs. This dissertation analyzes and addresses the most important shortcomings of two major shared resources: the Last Level Cache (LLC) and the Network on Chip (NoC). First, we study the scalability of both electrical and optical NoCs for future multicoresand many-cores. To perform this study, we model optical interconnects in a cycle-accurate multicore simulation framework. A proper model is required; otherwise, important performance deviations may be observed otherwise in the evaluation results. The study reveals that, as the core count grows, the effect of distance on the end-to-end latency can negatively impact on the processor performance. In contrast, the study also shows that silicon nanophotonics are a viable solution to solve the mentioned latency problems. This dissertation is also motivated by important design concerns related to current memory hierarchies, like the oversizing of private cache space, data replication overheads, and lack of flexibility regarding sharing of cache structures. These issues, which can be overcome in high performance processors by virtue of huge LLCs, can compromise performance in low power processors. To address these issues we propose a more efficient cache hierarchy organization that leverages optical interconnects. The proposed architecture is conceived as an optically interconnected two-level cache hierarchy composed of multiple cache modules that can be dynamically turned on and off independently. Experimental results show that, compared to conventional designs, static energy consumption is improved by up to 60% while achieving similar performance results. Finally, we extend the proposal to support both sequential and parallel applications. This extension is required since the proposal adapts to the dynamic cache space needs of the running applications, and multithreaded applications's behaviors widely differ from those of single threaded programs. In addition, coherence management is also addressed, which is challenging since each cache module can be assigned to any core at a given time in the proposed approach. For parallel applications, the evaluation shows that the proposal achieves up to 78% static energy savings. In summary, this thesis tackles major challenges originated by the sharing of on-chip caches and communication resources in current multicores, and proposes new cache hierarchy organizations leveraging optical interconnects to address them. The proposed organizations reduce both static and dynamic energy consumption compared to conventional approaches while achieving similar performance; which results in better energy efficiency. / Puche Lara, J. (2021). Novel Cache Hierarchies with Photonic Interconnects for Chip Multiprocessors [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/165254 / TESIS

The work presented in this thesis aims at validating an original multicriteria performances estimation tool, NESSIE, dedicated to the prediction of performances to accelerate the design of electronic embedded systems. <p><p>This tool has been developed in a previous thesis to cope with the limitations of existing design tools and offers a new solution to face the growing complexity of the current applications and electronic platforms and the multiple constraints they are subjected to. <p><p>More precisely, the goal of the tool is to propose a flexible framework targeting embedded systems in a generic way and enable a fast exploration of the design space based on the estimation of user-defined criteria and a joint hierarchical representation of the application and the platform.<p><p>In this context, the purpose of the thesis is to put the original framework NESSIE to the test to analyze if it is indeed useful and able to solve current design problems. Hence, the dissertation presents :<p><p>- A study of the State-of-the-Art related to the existing design tools. I propose a classification of these tools and compare them based on typical criteria. This substantial survey completes the State-of-the-Art done in the previous work. This study shows that the NESSIE framework offers solutions to the limitations of these tools.<p>- The framework of our original mapping tool and its calculation engine. Through this presentation, I highlight the main ingredients of the tool and explain the implemented methodology.<p>- Two external case studies that have been chosen to validate NESSIE and that are the core of the thesis. These case studies propose two different design problems (a reconfigurable processor, ADRES, applied to a matrix multiplication kernel and a 3D stacking MPSoC problem applied to a video decoder) and show the ability of our tool to target different applications and platforms. <p><p>The validation is performed based on the comparison of a multi-criteria estimation of the performances for a significant amount of solutions, between NESSIE and the external design flow. In particular, I discuss the prediction capability of NESSIE and the accuracy of the estimation. <p><p>-The study is completed, for each case study, by a quantification of the modeling time and the design time in both flows, in order to analyze the gain achieved by our tool used upstream from the classical tool chain compared to the existing design flow alone. <p><p><p>The results showed that NESSIE is able to predict with a high degree of accuracy the solutions that are the best candidates for the design in the lower design flows. Moreover, in both case studies, modeled respectively at a low and higher abstraction level, I obtained a significant gain in the design time. <p><p>However, I also identified limitations that impact the modeling time and could prevent an efficient use of the tool for more complex problems. <p><p>To cope with these issues, I end up by proposing several improvements of the framework and give perspectives to further develop the tool. / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished

The work presented in this thesis targets the analysis and implementation of multi-criteria performance prediction methods for System-on-Chips (SoC).<p>These new SoC architectures offer the opportunity to integrate complete heterogeneous systems into a single chip and can be used to design battery powered handhelds, security critical systems, consumer electronics devices, etc. However, this variety in terms of application usually comes with a lot of different performance objectives like power consumption, yield, design cost, production cost, silicon area and many others. These performance requirements are often very difficult to meet together so that SoC design usually relies on making the right design choices and finding the best performance compromises.<p>In parallel with this architectural paradigm shift, new Very Deep Submicron (VDSM) silicon processes have more and more impact on the performances and deeply modify the way a VLSI system is designed even at the first stages of a design flow.<p>In such a context where many new technological and system related variables enter the game, early exploration of the impact of design choices becomes crucial to estimate the performance of the system to design and reduce its time-to-market.<p>In this context, this thesis presents: <p>- A study of state-of-the-art tools and methods used to estimate the performances of VLSI systems and an original classification based on several features and concepts that they use. Based on this comparison, we highlight their weaknesses and lacks to identify new opportunities in performance prediction.<p>- The definition of new concepts to enable the automatic exploration of large design spaces based on flexible performance criteria and degrees of freedom representing design choices.<p>- The implementation of a couple of two new tools of our own:<p>- Nessie, a tool enabling hierarchical representation of an application along with its platform and automatically performs the mapping and the estimation of their performance.<p>-Yeti, a C++ library enabling the defintion and value estimation of closed-formed expressions and table-based relations. It provides the user with input and model sensitivity analysis capability, simulation scripting, run-time building and automatic plotting of the results. Additionally, Yeti can work in standalone mode to provide the user with an independent framework for model estimation and analysis.<p><p>To demonstrate the use and interest of these tools, we provide in this thesis several case studies whose results are discussed and compared with the literature.<p>Using Yeti, we successfully reproduced the results of a model estimating multi-core computation power and extended them thanks to the representation flexibility of our tool.<p>We also built several models from the ground up to help the dimensioning of interconnect links and clock frequency optimization.<p>Thanks to Nessie, we were able to reproduce the NoC power consumption results of an H.264/AVC decoding application running on a multicore platform. These results were then extended to the case of a 3D die stacked architecture and the performance benefits are then discussed.<p>We end up by highlighting the advantages of our technique and discuss future opportunities for performance prediction tools to explore. / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished

Lab-on-a-chip systems for point-of-care testing demonstrate a promising development towards more accurate diagnostic tests that are of extreme importance for the future global health. This work presents an agglutination assay performed in micrometer sized well using Janus PS/Ag/AgCl micromotors to enhance the interactions between goat anti-human IgM functionalized particles and Human IgM. The fabricated microwell chips are a suitable platform to analyze the interaction between different particles and to perform the agglutination assays. The interaction between active Janus particles and passive and functionalized particles is studied, as well as the influence of ions on the motion of the Janus particles. Agglutination assays are performed with and without the presence of Janus particles, and in different PBS concentrations. Once illuminated with blue light, passive SiO2 particles were effectively excluded from Janus particles, while SiO2 NH2 particles revealed attraction. In contrast, functionalized SiO2 NH2 Ab particles suspended in PBS did not show any interaction. It was found that the optimal working conditions for antibodies and Janus particles differed and, as a result, the Janus particles did not reveal a desirable interaction between the functionalized particles and IgM. Further experiments should be performed to find the proper conditions in which the antibodies and the Janus particles maintain their activities. It is believed that an effective interaction between the functionalized and Janus particles could be achieved by modifying the parameters that affect their interaction such as the zeta potential and the medium in which the assay is being performed. This preliminary work provides the first steps towards the development of a fully integrated lab on a chip system for point of care testing.:Abstract ........................................................................................................................ iii Acknowledgments.......................................................................................................... v Table of Contents .......................................................................................................... vi List of Tables ............................................................................................................. viii List of Figures ............................................................................................................... ix Abbreviations ................................................................................................................. x 1. Introduction ............................................................................................................ 1 1.1 In vitro diagnostic tests ........................................................................................ 1 1.1.1 Point-of-care tests ......................................................................................... 2 1.2 Agglutination assay .............................................................................................. 2 1.3 Lab-on-a-chip ....................................................................................................... 5 1.4 Self-propelled particles ........................................................................................ 6 1.4.1 Light-driven Ag/AgCl micromotors ............................................................. 6 1.5 Aim ...................................................................................................................... 9 2. Materials and Methods ......................................................................................... 11 2.1 Microwell fabrication .................................................................................... 11 2.2 Microswimmers fabrication .......................................................................... 12 2.3 Functionalization of particles ........................................................................ 12 2.4.1 Scanning electron microscope ............................................................... 14 2.4.2 UV-vis spectroscopy .............................................................................. 14 2.4.3 Zeta potential ......................................................................................... 14 2.4.4 Optical microscopy ................................................................................ 15 2.5 Motion Experiments ...................................................................................... 15 2.6 Agglutination assay ....................................................................................... 16 2.7 Effect of PBS ................................................................................................. 16 2.7.1 Janus particles ........................................................................................ 16 2.7.2 Agglutination assay ................................................................................ 17 2.7.3 Exclusion of functionalized particles ..................................................... 17 3. Results and Discussion ........................................................................................ 18 3.1 Microwell chip with integrated Janus particles ................................................. 18 3.2 Characterization of particles .............................................................................. 19 3.2.1 UV-vis spectroscopy ................................................................................... 19 3.2.2 Zeta potential .............................................................................................. 21 3.2.3 Agglutination assay in PEG-covered glass slides ....................................... 22 3.3 Motion experiments ........................................................................................... 23 3.3.1 Exclusion time ............................................................................................ 23 3.3.2 On/off light cycles....................................................................................... 26 3.4 Agglutination assay ............................................................................................ 28 3.4.1 Assay performed in wells............................................................................ 28 3.4.2 Assay performed in wells with Janus particles ........................................... 29 3.5 Effect of PBS concentration............................................................................... 30 3.5.1 Janus particles ............................................................................................. 30 3.5.2 Agglutination assay ..................................................................................... 32 3.5.3 Exclusion of functionalized particles .......................................................... 33 4. Conclusions .......................................................................................................... 35 References .................................................................................................................... 37 Declaration of Research Integrity and Good Scientific Practice ................................. 42

Cette thèse aborde le problème de la synchronisation globale de grand système sur puce (SoC). Il est centré sur l'étude d'une technique de remplacement de la distribution d'horloge classique et d'une communication asynchrone. Il permet la mise en œuvre de circuit synchrone très fiable. Mon projet de thèse vise à étudier et mettre en œuvre un vaste réseau (10x10) de boucle à verrouillage de phase tous numérique (ADPLL), contenant 100 nœuds générant une horloge pour chaque circuit numérique local. Le prototype a été réalisé sur les horloges de génération de silicium dans la gamme de 903-1161 MHz. Elle met en évidence une erreur de phase maximale de moins de 40 ps entre deux horloges dans toutes les zones voisines. Un autre résultat important est l'analyse de l'erreur de phase entre les deux oscillateurs non-voisins dans la distance. En étudiant un prototype FPGA du réseau, on a obtenu que l'erreur de phase maximale à l'état d'équilibre entre un signal d'horloge et le signal de référence est inférieur à trois étapes des étapes de quantification PFD. Afin de valider les performances de la synchronisation dans ASIC, nous avons conçu un circuit d'une erreur de mesure sur la puce d'horloge. Ce circuit a un taux faible de la lecture hors puce (quelques MHz), et une résolution élevée (+ -2,5 ps). Reconfiguration constitue une autre caractéristique intéressante. Nous avons exploré cette fonction et a proposé une nouvelle topologie avec des configurations différentes pour les nœuds sur la frontière et dans le noyau du réseau. Cette topologie présente un avantage en interdisant la propagation des erreurs de phase et de réflexion. / This thesis addresses the problem of global synchronization of large system on chip (SoC). It focuses on the study of an alternative clock generation technique to conventional clock distribution and asynchronous communication. It allows implementation of highly reliable synchronous circuit. My PhD project aims to study and implement a large network (10x10) of all digital phase-locked loop (ADPLL), containing 100 nodes generating a clock for each local digital circuitry. The prototype was implemented on silicon generating clocks in the range 903-1161 MHz. It highlights a maximum phase error of less than 40 ps between two clocks in any neighboring zones. Another important result is the analysis of phase error between two non-neighboring oscillators in distance. By studying an FPGA prototype of the network, we obtained that maximum phase error at steady state between any clock signal and the reference signal is less than three steps of the PFD quantification steps. In order to validate the performance of synchronization in ASIC, we designed an on-chip clocking error measurement circuit. This circuit has a low rate for the off-chip readout (several MHz), and a high resolution (+-2.5 ps). Reconfigurability is another attractive feature. We have explored this feature and proposed a novel topology with different configurations for nodes on the border and in the kernel of the network. This topology has an advantage in prohibiting phase error propagation and reflection.

No description available.

No description available.

Poor chip breaking is a normal problem in the field of machining in many manufacturing plants. The researches on chip control has started from the early 1900s, it has developed for more than one hundred years and researchers are still working on it to establish a ‘total’ chip control system. The purpose of this project is chip breaking improvement for reducing downtime and further increasing OEE, because of the problems long chips that cause during a soft turning process. This thesis provides basic theories and existing methods for chip breaking which are helpful to understand chip breaking and to generate solutions for chip breaking optimization. During the project, five concepts are generated and two concepts are tested which are presented in this report. The concept ‘multiple tool paths’, which was verified by tests, could successfully reduce the length of metal chips and improving the performance of chip breaking. / Dålig spånbrytning är ett vanligt problem vid maskinbearbetning i många tillverkningsanläggningar. Forskningen om spånbrytning inleddes under tidigt 1900-tal, den har alltså utvecklats i mer än hundra år och forskare arbetar fortfarande med att skapa ett "totalt" spånbrytningssystem. Syftet med det här projektet är att förbättra spånbrytningen för att minska ledtiden och ytterligare öka OEE vid mjukvarvning på grund av de problem som långa chips orsakar. Denna avhandling behandlar grundläggande teorier och befintliga metoder för spånbrytning som är användbara för att förstå spånbrytning och därmed kunna föreslå lösningar för att optimera spånbrytningen. Under projektet skapades fem koncept, varav två provades. Konceptet "flera verktygsbanor" verifierades genom prov. Det visas att det konceptet med framgång kunde minska längden på metallchip och förbättra spånbrytningens prestanda.