This thesis describes the synthesis, characterization and photocatalytic applications of carbon nitride (C3N4) and titanium dioxide (TiO2) materials. C3N4 was prepared from the thermal decomposition of a trichloromelamine (TCM) precursor. Several different reactor designs and decomposition temperatures were used to produce chemically and thermally stable orange powders. These methods included a low temperature glass Schlenk reactor, a high mass scale stainless steel reactor, and decomposition at higher temperatures by the immersion of a Schlenk tube into a furnace. These products share many of the same structural and chemical properties when produced by these different methods compared to products from more common alternate precursors in the literature, determined by infrared spectroscopy (IR), nuclear magnetic resonance spectroscopy (NMR), powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and elemental analysis. C3N4 is capable of utilizing light for photocatalysis due to its moderate band gap (Eg), measured to be between 2.2 and 2.5 eV. This enables C3N4 to be used in the photocatalytic degradation of organic dyes and the production of hydrogen via the water-splitting reaction. C3N4 degraded methylene blue dye to less than 10% of its initial concentration in less than an hour of UV light illumination and 60% under filtered visible light in 150 minutes. It also degraded methyl orange dye to below 20% in 70 minutes under UV light and below 60% in 150 minutes under visible light. Using precious metal co-catalysts (Pt, Pd, and Ag) photo-reduced onto the surface of C3N4, hydrogen was produced from a 10% aqueous solution of triethanolamine at rates as high as 260 μmol h-1 g-1. C3N4 was also modified by mixing the precursor with different salts (NaCl, KBr, KI, KSCN, and NH4SCN) as hard templates. Many of these salts reacted with TCM by exchanging the anion with the chlorine in TCM. The products were mostly prepared using the high temperature Schlenk tube reactor, and resulted in yellow, orange, or tan-brown products with Eg values between 2.2 and 2.7 eV. Each of these products had subtle differences in the IR spectra and elemental composition. The morphology of these C3N4 products appeared to be more porous than unmodified C3N4, and the surface area for some increased by a factor of 4. These products demonstrated increased activity for photocatalytic hydrogen evolution, with the product from TCM-KI reaching a peak rate as high as 1,300 µmol h-1 g-1. C3N4 was coated onto metal oxide supports (SiO2, Al2O3, TiO2, and WO3) with the goal of utilizing enhanced surface area of the support or synergy between two different semiconductors. These products typically required higher temperature synthesis conditions in order to fully form. The compositions of the SiO2 and Al2O3 products were richer in nitrogen and hydrogen compared to unmodified C3N4. The higher temperature reactions with C3N4 and WO3 resulted in the formation of the HxWO3 phase, and an alternate approach of coating WO3 on C3N4 was used. The degradation of methyl orange showed a significant increase in adsorption of dye for the composites with SiO2 and Al2O3, which was not seen with any of the individual components. The composite between C3N4 and TiO2 showed improved activity for hydrogen evolution compared to unmodified C3N4. The surface of TiO2 was modified by the reductive photodeposition of several first row transition metals (Mn, Fe, Co, Ni, and Cu). This process resulted in the slight color change of the white powder to shades of light yellow, blue or grey. Bulk elemental analysis showed that these products contained between 0.04-0.6 at% of the added metal, which was lower than the targeted deposit amount. The Cu modified TiO2 had the largest enhancement of photocatalytic hydrogen evolution activity with a rate of 8,500 µmol h-1 g-1, a factor of 17 higher than unmodified TiO2.

The current energy and environmental scenario in the world demands acute attention on sustainable repurposing of waste CO2 to high value hydrocarbons that not only addresses the CO2 mitigation problem, but also provides pathways for a closed loop synthetic carbon cycle. Difference in the scales of global CO2 emissions (about 40 Gtpa, 2017) and the carbon capture and sequestration (CCS) facilities (estimated cumulative 40 Mtpa, 2018) provokes active research on this topic. Solar thermochemical (STC) and visible light photocatalysis are two of the most promising routes that have garnered attention for this purpose. While STC has the advantages of high CO2 conversion rates, it operates at high temperatures (more than 1000 °C) limiting its industrial implementation. Photocatalysis, on the contrary, is plagued by the poor quantum efficiency and conversion rates, although its exhibits the benefits of low temperature operation. Thus, any significant progress towards low temperature STC and visible light photocatalytic CO2 reduction is a giant leap towards a greener and sustainable energy solution. This dissertation is an effort towards improving both the STC and photocatalytic CO2 reduction. Reverse water gas shift - chemical looping (RWGS-CL) is a modified STC approach that has the potential for low temperature CO2 conversion. RWGS-CL process uses mixed metal oxides like perovskite oxides (ABO3) for the conversion to CO, a potential feedstock for subsequent hydrocarbon production. Generation of oxygen vacancy defects on these perovskite oxides is a key step of RWGS-CL and thus, oxygen vacancy formation energy has been found to be a key descriptor for this process. Using density functional theory based calculations, this intrinsic material property has been used towards rational design of better catalysts. Highest rate of CO2 conversion at the low temperatures of 450 °C was demonstrated by earth abundant perovskite oxide via RWGS-CL. This low temperature and stable CO2 conversion process enables thermal integration with subsequent Fischer Tropsch processes for the hydrogenation of CO to hydrocarbons. Parallel to the developments on materials discovery, another crucial parameter that deserves attention is the surface termination effects of the perovskite oxides. Hence, the site specificity of the bulk and surface oxygen vacancies have been probed in detail towards elucidating the CO2 conversion performance over these materials. In the view of recent progress on the growth of selective crystal facets and terminations, this study opens new avenues for enhanced CO2 conversion performance not only through bulk composition variation, but also via exposing desired crystal facets. Type-II semiconductor heterojunctions (staggered type) are promising candidates for efficient photocatalytic reactions, not only because of their capabilities of electronic density of states tuning, but also their ability to segregate the excited electrons and holes into different materials thereby restricting exciton recombination. Metal oxynitride heterojunctions have recently demonstrated promising activity on visible light water splitting. Elucidating the structure-function relationships for these materials can pave the way towards designing better CO2 conversion photocatalysts. This dissertation focuses on unravelling the roles of material composition, anion vacancy defects and lattice strain towards modulating the electronic density of states of lateral and vertical heterojunctions of (ZnO)X(AlN)1-X and (ZnO)X(GaN)1-X. The heterojunctions consist of periodic potential wells that allows for restricting interlayer charge transport. Increased ZnO concentration was explicitly shown to decrease the band gap due to N 2p and Zn-3d repulsion. Biaxial and vertical compressive strain effected increased band gap while tensile strain reduced the same. Oxygen vacancies was found to have different effect on the electronic state of the materials. When present in charged state (+2), it promotes mid gap state formation, while in neutral state it revealed increased electronic densities near the valence band and conduction band edges. These fundamental site specific material property tuning insights are essential for designing better photocatalysts for future.

Growing demand and shortages of potable water sources due to industrialization have become a great concern worldwide. Various approaches and solutions have been adopted to provide cleaner and quality water. In a preliminary study, a method of treating wastewater was investigated in which algae were used to remove nutrients (nitrogen and phosphorous) from wastewater and then the algae were harvested for use as a biofuel. The results from this investigation are included in the Appendix B. Employing traditional oxidants, such as hydrogen peroxide, chlorine, and ozone, for treatment of recalcitrant organic compounds have achieved less promising results. However, photocatalysis, an advanced oxidation process (AOP), which is a low-cost and high-efficiency technique, has been widely recognized as a promising approach for water purification and elimination of organic constituents in wastewater. Photocatalysis is the increase in the rate of a chemical reaction by employing a catalyst in the presence of photons. Generally, for a high performance photocatalyst, light of appropriate wavelength is used to activate a catalyst in close contact with contaminants, thereby modifying the rate of the reaction. The presence of these contaminants could pose potential health and environmental concerns, especially in a controlled environment such as on a space station or during long-term manned missions. Thus, the development of energy efficient and "green" technologies to reduce or eliminate organic constituents in wastewater has important potential applications. This research investigated the supported semiconductor photocatalysts (TiO2 and ZnO), particularly ZnO nanorods and nanowires, their synthesis methods, properties and corresponding effectiveness in photocatalysis. The effect of transition metal co-catalysts on the photocatalytic properties of TiO2 was investigated. Although TiO2 is the most extensively studied photocatalyst for water decontamination, ZnO, as presented in this work, could be a substitute because of its lower cost, relative energy bandgap and higher visible light photoactivity. Both photocatalysts were doped and screened for the decomposition of model contaminates, rhodamine B (RhB), phenol and methyl orange, under ultraviolet and/or visible light irradiation. In the photodegradation of RhB, TiO2/Ru 1% showed a superior photocatalytic activity relative to P25-TiO2 under broad-band irradiation, while doped ZnO-Ag resulted in better photodegradation of methyl orange, compared to P25-TiO2, under visible light irradiation. The morphology and estimated chemical composition of photocatalysts were determined by energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM). Brunhauer, Emmett and Teller (BET) analysis was utilized to measure mass-specific surface area(s). A X-ray diffraction (XRD) study was carried out to confirm the identity of photocatalyst phase(s) present. The cause of low photocatalytic activity under an inert atmosphere, the simple effective fabrication technique of doped ZnO nanowires over TiO2 and properties of the photocatalyst are also discussed.

Natural organic matter (NOM) occurs ubiquitously in drinking water supplies and is problematic since it serves as a precursor to disinfection by-products (DBPs) formation. Stricter DBP regulations will drive utilities to consider advanced treatment processes for DBP control through NOM removal. Herein, the transformation of NOM in homogeneous (UVA/H2O2 and UVA/Fe/H2O2) and heterogeneous (UVA/TiO2) Advanced Oxidation Processes (AOPs) were studied. Organic matter from three different sources was investigated in this work, specifically a commercial humic acid, and two Australian surface water sources. The transformation of the organic matter as a result of oxidation was investigated through multiple analytical techniques, such as UV-Vis spectroscopy, DOC analysis, high performance size exclusion chromatography (HPSEC), resin fractionation, liquid chromatography with organic carbon detection (LC-OCD) and disinfection byproducts formation potential. The multi-analysis approach is required due to the complex and heterogeneous nature of NOM. Each analytical technique provides complementary information on different properties of NOM, leading to a comprehensive understanding on how AOPs transform the chemical and physical properties of NOM. Both homogeneous and heterogeneous AOPs were found to be effective for NOM removal. However, complete mineralisation was not achieved, even under prolonged irradiation. Large aromatic and hydrophobic organics were degraded into lower molecular weight hydrophilic compounds, which had weak UV absorbance at 254 nm. In the UVA/TiO2 treatment, multi-wavelength HPSEC analysis demonstrated the formation of low molecular weight compounds with strong absorbance at wavelength lower than 230 nm. These residual organic compounds, though recalcitrant, had a low reactivity to chlorine to form THMs, and were identified to be low molecular weight acids and neutral compounds from LC-OCD analysis. Finally, the current work reports the novel synthesis of magnetic photocatalyst for NOM oxidation from low cost precursors to solve the separation problem of nano-sized particles. Magnetite particles were coated with a layer of protective silica from sodium silicate precursor. Photoactive titanium dioxide was then deposited onto the silica coated particles using titanium tetrachloride precursor. The as-prepared magnetic photocatalyst exhibited excellent stability and durability. Although the photoactivity of the magnetic photocatalyst is lower than commercial TiO2 photocatalyst, it can be easily recovered by magnetic field.

Nitrogen-doped TiO2 nanotubes with enhanced visible light photocatalytic activity have been synthesized using commercial titania P25 as raw material by a facile P25/urea co-hydrothermal method. Morphological and microstructual characteristics were conducted by transmission electron microscopy, powder X-ray diffraction, and nitrogen adsorption/desorption isotherms; chemical identifications were performed using X-ray photoelectron spectroscopy, and the interstitial nitrogen linkage to the TiO2 nanotubes is identified. The photocatalytic activity of all nitrogen-doped TiO2 nanotubes synthesized by different urea content, evaluated by the decomposition of rhodamine B dye solution under visible light using UV¡VVis absorption spectroscopy, is found to exhibit higher degradation rate than that of P25. Factors affecting the photocatalytic activity of RB were analyzed and a possible mechanism of photodegradation was also proposed. The high photocatalytic activity was attributed to the process of two different mechanisms, one was the direct degradation of the chromophoric system and the other was successive deethylation of the four ethyl groups.

This study investigated the effects of temperature and humidity on the photocatalytic oxidation of volatile organic compound (VOCs) over titanium dioxide. Benzene, methyl tert-butyl ether (MTBE), perchloroethylene (PCE), and toluene were selected to investigate the influences of temperature and humidity on photocatalytic conversion. Among these four VOCs, benzene and MTBE were selected for the investigation of reaction pathways and kinetics. This work employed a self-designed annular packed-bed photocatalytic reactor to determine the conversion and reaction rates during photocatalytic degradation of VOCs. Degussa P-25 TiO2 was used as the photocatalyst and a 15 W near-UV lamp (350 nm) served as the light source. Benzene conversions increased with temperature below 160 ºC, but decreased above 160 ºC. Moreover, the conversions of MTBE increased with temperature from 30 to 120 ºC, and the thermocatalytic reaction began above 120 ºC. The conversions of PCE decreased as the temperature increased from 120 to 200 ºC. Toluene conversions almost remained constant at 100~200 ºC. Based on the gas-solid catalytic reaction theory, raising the reaction temperature could promote the chemical reaction rate and reduce reactant adsorption on TiO2 surfaces. The overall reaction rate increased with temperature, indicating that the reduction of reactant adsorption did not affect the overall reaction, and thus the chemical reaction was the rate-limiting step. As the chemical reaction rate gradually increased and the reactant adsorption decreased with temperature, the rate-limiting step could shift from the chemical reaction to the reactant adsorption, while the overall reaction rate decreased with temperature. Additionally, the competitive adsorption between VOCs and water for the active sites on TiO2 resulted in VOCs influent concentration and humidity promoting or inhibiting the reaction rate. The mineralization of benzene and the selectivity of CO and CO2 were not obviously affected under various temperatures, humidities, and influent benzene concentrations. The benzene mineralization ratios ranged from 0.85 to 1.0, to which CO and CO2 contributed approximately 5~20% and 80~95%, respectively. Temperature and humidity variation did not influence the photocatalytic reaction pathway of benzene. Acetone (AC) and tert-butyl alcohol (TBA) were two major organic products for the photocatalysis of MTBE. The addition of water transferred the reaction pathway from producing AC to TBA, while the temperature increase transferred the reaction pathway from producing TBA to AC. A modified bimolecule Langmuir-Hinshelwood kinetic model was developed to simulate the temperature and humidity related promotion and inhibition of the photocatalysis of benzene and MTBE. The competitive adsorption of VOCs and water on the active sites resulted in VOCs influent concentration and humidity promoting or inhibiting the reaction. The reaction rate constant increased with temperature while the adsorption equilibrium constants decreased, confirming that increasing reaction temperature enhanced the chemical reaction, but reduced the adsorption of VOCs and water. Furthermore, the correlation developed here was also used for determining the apparent activation energy of photocatalytic oxidation of VOCs and the adsorption enthalpies of benzene, MTBE, water vapor, and oxygen.

The room temperature photocatalytic oxidation of carbon monoxide in excess air was examined over silica/titania and 0.1%palladium/silica/titania catalysts under UV irradiation. The experiments were conducted in batch re-circulated reactor with the initial 1000 ppm carbon monoxide in air and 0.5 g catalyst charge and the conversion of carbon monoxide to carbon dioxide was followed by FT-IR spectro-photometer. The change in gas composition in dark and under 36 Watts of UV irradiation exposed to a catalyst area of 12.4 centimeter square indicated both adsorption of carbon monoxide and conversion of carbon monoxide to carbon dioxide over the catalyst samples. The effect of catalyst composition (silica/titania) ratio and the presence of palladium oxide were investigated. The catalyst samples were synthesized by sol-gel technique and all samples were hydrothermally treated before calcination in air. The catalyst samples were characterized by XRD and nitrogen adsorption techniques. XRD results indicated that titania is comprised of pure anatase phase and palladium oxide preferantially dispersed over titania. BET surface area of the samples were observed to increase with silica loading and the BJH results showed isotherms of Type V v with H2 hysteresis loops. The highest carbon monoxide adsorption rate constant was achieved with pure silica with the highest surface area. Photocatalytic activity measurements indicated that carbon monoxide in excess air can be successfully oxidized at room temperature over the titania photocatalyts. Higher physisorption was observed over higher silica containing samples and higher oxidation activity was observed with increasing titania/silica ratio. The optimum titania/silica ratio was determined by the titania content and surface area of catalyst. The activity tests were also indicated that the addition of palladium oxide phase synergistically increased the adsorption and oxidation activity of the catalysts.

When nanoparticles are small in size compared to the wavelength of incident light, a localized surface plasmon resonance occurs. For certain noble metals, such as gold and silver, this frequency occurs in the visible or near IR range, and therefore it can be utilized for many important applications. Only silver and gold nanoparticles were utilized in this thesis work, and they were used in application for three separate files: environment, catalysis, and energy.

Kyoto University (京都大学) / 0048 / 新制・課程博士 / 博士(工学) / 甲第19000号 / 工博第4042号 / 新制||工||1622 / 31951 / 京都大学大学院工学研究科分子工学専攻 / (主査)教授 田中 庸裕, 教授 今堀 博, 教授 阿部 竜 / 学位規則第4条第1項該当

This dissertation presents novel applications of ligand-capped II-VI semiconductor nanocrystals (i.e. CdSe and CdTe).Hybrid polymer-nanocrystal thin films were prepared using a bottom-up electrochemical crosslinking method, where thiophene-functionalized CdSe NCs were wired to electron-rich 3,4-dioxy-substituded thiophene polymers. Both nanocomposite and effective monolayer (EML) films were achieved by controlling monomer feed ratios during the crosslinking steps. These hybrid thin films showed enhanced photoelectrochemical current efficiencies with a variety of solution acceptor molecules compared to polymer control films, which was due to sensitization by the CdSe NCs. The electronic structure of the polymer played a critical role in the potential (doping) dependent hole capture efficiency from photoexcited CdSe NCs. Furthermore, photocurrent efficiencies were correlated with nanocrystal size, which was a direct product of frontier orbital energy shifting due to quantum confinement effects.All-inorganic CdTe-CdSe nanocrystal solar cells were fabricated by a facile layer-by-layer procedure. A low-temperature sintering strategy was utilized to electronically couple the nanocrystal thin films, which maintained the individual electronic properties of the nanocrystals. The electrical characteristics of these solar cells displayed predictable trends in open circuit voltage with varying CdSe NC diameter.Novel CdSe NC diffraction gratings were prepared by a facile microcontact molding procedure. These transmission gratings showed exceptionally high diffraction efficiencies that were dependent on optimum grating morphologies and the refractive index contrast provided by the nanocrystals, which was size-dependent. These films also showed promise as coupling gratings for internal reflection elements.