Technologies laser pour l’élaboration de matériaux carbonés pour microsystèmes analytiques environnementaux. Pas de résumé en français fourni / Amorphous carbon nitride (a-CzN) material has attractor much attention in research and development. Recently, it has become a more promising electrode material than conventional carbon based electrodes in electrochemical and biosensor applications. Nitrogen containing amorphous carbon (a-C:N) thin films have been synthesized by femtosecond pulsed laser deposition (fs-PLD) coupled with plasma assistance through Direct Current (DC) bias power supply. During the deposition process, various nitrogen pressures (0 to 50 Pa) and DC bias (0 to -350 V) were used in order to explore a wide range of nitrogen content into the film. The structure and chemical composition of the films have been studied by using Multi-wavelength (MW) Roman spectroscopy, electron energy-loss spectroscopy (EELS), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy (HRTBM). The surface morphology has been studied by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Increasing the nitrogen pressure or adding a DC bias induced an increase of the N content, up to 28 at.%. Nitrogen content increase induces a higher sp2 character of the film. However DC bias has been found to increase the film structmal disorder, which was detrimental to the electrochemical properties. Indeed the electrochemical measurern-ts, investigated by cyclic voltammetry (CV), demonstrated that the a-CzNfilms show better electron transfer kinetics, reversibility and excellent reproducibility than the pure a-C films. Electrochemical grafting from diazoniurn salts was successfully achieved on this film, with a surface coverage of covalently bonded molecules close to the dense packed monolayer of ferrocene

Le but de ce travail de thèse est de réaliser des vannes de spin « naturelles » constituées d’un matériau unique. Le matériau en question doit contenir une alternance de feuillets magnétiques et non magnétiques et présenter différents états magnétiques. Ce système modèle ne présenterait alors ni d’inter diffusion ni de rugosité aux interfaces magnétiques/non-magnétiques et pourrait constituer un système modèle pour les études des phénomènes de transport dépendant de spin. Le CoV2O6 est un oxyde polymorphe de basse dimensionnalité. Les deux phases (α et γ) présentent chacune plusieurs plateaux d’aimantation induits par un champ magnétique. Le premier objectif est de comprendre la structure cristalline et magnétique de ce composé, ce qui a été réalisé par des mesures d’aimantation, de diffraction des rayons X et de neutrons sur des poudres et monocristaux. Les résultats de la phase α sont appuyés par des calculs ab initio. Le second objectif est de déposer ce matériau en couche mince afin d’analyser ses propriétés de transport. Des films épitaxiés de γ CoV2O6 ont été obtenus sur TiO2(100) et TiO2/Pt(111) par ablation laser. Le dépôt sur l’électrode de Pt montre la présence de six variants entrainant l’observation de plateaux d’aimantation supplémentaires. / The purpose of this work is to synthesize “natural” spin valves within one unique material. The material needs a crystalline structure formed by stacking magnetic and non-magnetic sheets as well as different magnetic states. Such model system could be used for the study of spin dependent transport properties as no-roughness or diffusion at the magnetic/non-magnetic interfaces is allowed. The polymorph low-dimensional oxide CoV2O6 is such a material. Both phases (α and γ) exhibit field induced magnetization plateaus. This study’s first aim is to understand crystalline and magnetic structures. Investigations were performed on powders and single crystals using magnetization measurements as well as X-ray and neutron diffraction measurements. The magnetic properties of α CoV2O6 were supported by ab initio calculations. The second aim is to grow CoV2O6 thin films in order to analyze further the transport properties. Epitaxial γ CoV2O6 thin films were obtained by pulsed laser ablation on both TiO2(100) and TiO2/Pt(111) substrates. Films grown on Pt electrode exhibit six variants which allows observing additional magnetization plateaus.

Sonder la matière en utilisant des nanoparticules luminescentes nécessite une compréhension de chaque processus pouvant modifier leurs propriétés optiques. Cette thèse se focalise sur l'influence de l'environnement diélectrique sur la luminescence de deux types de nanoobjets : (i) des boites quantiques colloïdales (QDs), et (ii) des nanobâtonnets d'or. L'objectif est d'évaluer les potentialités de ces nanostructures comme sondes locales de l'environnement diélectrique.L'évolution de la dynamique de relaxation de QDs dans différents environnements diélectriques est interprétée en terme d'indice de réfraction effectif local. Cette étude montre qu'une analyse détaillée de la sensibilité des QDs à l'environnement permet de les utiliser comme nanosondes biologiques d'indice de réfraction. Nous présentons également une nouvelle méthode pour l'encapsulation de QDs en matrice diélectrique solide, à travers le dépôt par laser pulsé. Les émetteurs peuvent être protégés par des films minces et subir des perturbations non-destructives et réversibles de leur environnement proche, à l'échelle de la particule unique, tout en analysant la dynamique de fluorescence. Finalement, la sensibilité de la résonance plasmon de nanobâtonnets d'or à l'approche d'une interface diélectrique est également sondée, puis comparée a celle des boites quantiques / Probing systems using luminescent nanoparticles requires the understanding of all the processes that influence the luminescence properties. This thesis focuses on the influence of the dielectric environment on the luminescence of two types of nanoparticles : (i) colloidal quantum dots (QDs), and (ii) gold nanorods. The aim of this work is to evaluate the potential of these nanostructures to act as local probes of the dielectric environment. The evolution of the relaxation dynamics of QDs in various dielectric media is interpreted in terms of local effective refractive index. This work shows that a detailed analysis of the sensitivity of the QDs to the environment allows their use as biological nanoprobes of refractive index. We furthermore present a new method for the encapsulation of QDs in a solid dielectric matrix, using pulsed laser deposition. The emitters can be incorporated in thin films and their local environment can be modified in a reversible and non-destructive way, while the emission dynamics is investigated at the single emitter level. Finally, the sensitivity of the surface plasmon resonance of gold nanorods to an approching dielectric interface is also studied, and compared to the one found for QDs

Ce travail constitue une contribution à l’étude de la synergie entre le vieillissement accéléré et l’évolution de la robustesse aux évènements singuliers pour les technologies MOS avancées. Ce manuscrit expose le travail fait autour de la Caractérisations des mécanismes de dégradation NBTI, HCI, TDDB et Electromigration sur les structures de tests conçues dans le véhicule de test NANOSPACE en technologie CMOS LP 65 nm. Il décrit aussi l’évaluation de la robustesse face aux évènements singuliers après un vieillissement de type NBTI sur les chaines de portes logiques (inverseurs, NOR, bascules D). Cette dernière partie nous a permis de démontrer que le vieillissement de type NBTI améliore la robustesse face aux SET dans ce cas d’étude. / This work is a contribution to the study of the synergy between accelerated aging and the evolution of robustness to single event effects for advanced MOS technologies.This manuscript describes the work done around the characterization of degradation mechanisms NBTI, HCI, TDDB and Electromigration on test structures designed in the NANOSPACE test vehicle on CMOS 65 nm Low Power technology. It also describes the evaluation of the robustness to Single Events Effects after NBTI aging on chains of logic gates (inverters, NOR, D flip-flops). This last part allows to show that the NBTI aging improves the robustness to SET in this case of study.

Les matériaux multiferroïques et/ou magnétoélectriques sont riches en promesses de nouvelles applications, comme par exemple des mémoires quatre états à densité accrue ou des mémoires magnétoélectriques à faible consommation d’énergie. Ces promesses restent cependant pour l’instant lettres mortes en raison du très faible nombre de matériaux présentant ces propriétés à température ambiante, et des forts courants de fuite qu’ils présentent en couches minces. Cette thèse porte sur un matériau prometteur en termes d’applications, car magnétoélectrique et ferrimagnétique à température ambiante, le ferrite de gallium de composition Ga0.6Fe1.4O3 (GFO).Nous avons démontré la possibilité de réduire les courants de fuite et moduler à volonté le type de conduction n ou p dans les couches minces de cet oxyde transparent, semi-conducteur, et magnétique, par dopage par des ions Ni2+. Une optimisation de la croissance de GFO par pulvérisation cathodique a par ailleurs montré qu’il était possible de le déposer sous champ électrique, ce qui ouvre d’intéressantes perspectives pour l’optimisation de la polarisation électrique des couches minces. / The multiferroic and/or magnetoelectric materials are full of promises in terms of new applications, such as for example higher density four state memories or lower power consuming magnetoelectric memories. These promises are however actually put off because too few materials present these properties at room temperature and because their thin films present too high leakage currents. This thesis focusses on a room temperature magnetoelectric and ferrimagnetic material promising in terms of applications, the gallium ferrite Ga0.6Fe1.4O3 (GFO).We have demonstrated the possibility to strongly reduce the leakage currents and perfectly tune from n to p the conduction type in transparent, semi-conducting, and magnetic thin films of GFO through Ni2+ doping. The optimization of the growth of GFO thin films by sputtering has moreover shown the possibility of deposition under an electric field, which opens ways to control of the electric polarization of the films.

L'objectif de ce travail était l'élaboration par ablation laser pulsé (PLD) et la caractérisation de couches minces d'oxydes dans le système K-Nb-O, et plus précisément d'une phase de structure bronze de tungstène quadratique (TTB) sous forme de nanorods, potentiellement intéressante dans le contexte de la recherche de nouveaux piézoélectriques sans plomb. Malgré une forte compétition de croissance entre les différentes phases, l'étude approfondie des conditions de dépôt a montré la possibilité d'obtenir les phases KNb3O8, K4Nb6O17, K6Nb10,88O30 (TTB) et KNbO3, en films minces après une phase d’optimisation essentielle. Nous avons déterminé l'influence des conditions de dépôt sur la formation et la nanostructuration de ces composés en couches minces. En particulier, il a été démontré que la température et la composition de la cible PLD avaient une forte influence sur la croissance de la phase de structure TTB. Une étude plus approfondie de ces phases a révélé que toutes avaient une morphologie spécifique liée à leur structure anisotrope, que nous avons pu contrôler par la croissance épitaxiale sur les substrats SrTiO3 orienté (100) et (110). L'existence d'une activité piézoélectrique dans des couches minces de la phase TTB, mise en évidence par PFM, lui confère un intérêt certain. Cette phase TTB a également été obtenue dans le système Na-K-Nb-O, très connu pour ses propriétés piézoélectriques et ferroélectriques, ouvrant la voie sur de nouvelles recherches. / The purpose of this work was the elaboration by pulsed laser deposition (PLD) and the characterization of thin films of oxides in the K-Nb-O system, and more precisely that of a tetragonal tungsten bronze phase (TTB) as nanorods, of potential interest as a new lead free piezoelectric. In spite of a strong growth competition between the different phases, the detailed study of the deposition conditions showed that it is possible to obtain KNb3O8, K4Nb6O17, K6Nb10,88O30 (TTB ) and KNbO3 in thin films form after an important optimization step. We have determined the influence of these deposition conditions on the formation and the nanostructuration of these compounds as thin films. In particular, it was shown that the temperature and the PLD target’s composition has a strong influence on the growth of the TTB structure. A further study of these phases revealed that all have a specific morphology related to their anisotropic structure, that we have controlled by the epitaxial growth on the (100) and (110) SrTiO3 substrates. The existence of a piezoelectric activity in the TTB thin films, evidenced by PFM, gives a great interest to this phase. This TTB phase was also obtained in the Na-K-Nb-O system, well known for its piezoelectric and ferroelectric properties, opening the way to new research.

Time-resolved Faraday rotation (TRFR) is a pulsed laser pump/probe optical measurement used to characterize electron spin dynamics in semiconductor materials. A Mach-Zehnder type interferometer with orthogonally polarized arms is presented as a device for TRFR measurement that is superior to optical bridge detection, the traditional measuring technique, since Faraday rotation can be passively optically amplified via interference. Operation of the interferometer is analyzed under ideal conditions. Corrections to the ideal case stemming from imperfectly aligned optics, finite polarization extinction ratios, and an imperfect recombination optic are analyzed using a matrix transformation approach. The design of the interferometer is presented and chronicled. A description of the single-beam active control system utilized to stabilize the interferometer by continuous corrections to the optical path length of one arm with a piezoelectric actuator is given. Optical amplification by increasing the power in either arm of the interferometer is demonstrated and TRFR measurements taken with the interferometer at ambient temperatures are compared with measurements taken with the optical bridge. We find the interferometer to offer a detection limit on the order of 50 mrad at room temperature, which is five times more sensitive than the optical bridge. Isolation and stabilization of the interferometer were also successful in reducing signal noise to a level comparable with the optical bridge. Our results demonstrate that the interferometer is a better detection device for Faraday rotation under ambient conditions. In the immediate future, improvements to the control system should be made and experiments should be performed with high-quality samples at cryogenic temperatures to confirm that the interferometer performs as favorably under those conditions.

No description available.

The temperature and/or entropy of electrically polarisable materials can be altered by changing electric field E. Research into this electrocaloric (EC) effect has focussed on increasing the size of the EC effects, with the long-term aim of building a cooler with an EC material at its heart. Materials and experimental methods are briefly reviewed. A ‘resetting’ indirect route to isothermal entropy change ∆S for hysteretic first-order transitions is described. An indirect route to adiabatic temperature change ∆T, without the need for field-resolved heat capacity data, is also described. Three temperature controllers were built: a cryogenic probe for 77-420 K with ∼5 mK resolution, a high-temperature stage with vacuum enclosure for 295-700 K with ∼15 mK resolution, and a low-temperature stage for 120-400 K with electrical access via micropositioners. Automation enables dense datasets to be compiled. Single crystals of inorganic salts (NH4)2SO4 , KNO3 and NaNO2 were obtained. Applying 380 kV cm−1 across (NH4)2SO4 , it was found that |∆S| ∼ 20 J K−1 kg−1 and |∆T | ∼ 4 K, using the indirect method near the Curie temperature TC = 223 K. Without the ‘resetting’ indirect method, |∆S| ∼ 45 J K−1 kg−1 would have been spuriously found. Preliminary indirect measurements on KNO3 and NaNO2 give |∆S| ∼ 75 J K−1 kg−1 for ∆E ∼ 31 kV cm−1 near TC = 400 K and |∆S| ∼ 14 J K−1 kg−1 for ∆E ∼ 15 kV cm−1 near TC = 435 K, respectively. A cation-ordered PbSc0.5Ta0.5O3 ceramic showing a nominally first-order transition at 295 K was obtained. The Clausius-Clapeyron phase diagram is revealed via indirect measurements where |∆S| ∼ 3.25 J K−1 kg−1 and |∆T | ∼ 2 K, and direct measurements where |∆T | ∼ 2 K. Clamped samples show broadening of the field-induced transition. Epitaxial, ∼64 nm-thick SrTiO3 films were grown by pulsed laser deposition on NdGaO3 (001) substrates with a La0.67Sr0.33MnO3 bottom electrode. The indirect method gives |∆S| ∼ 8 J K−1 kg−1 and |∆T | ∼ 3.5 K near 180 K with |∆E| = 780 kV cm−1. Finite element modelling (FEM) was used to optimise the geometry of multilayered capacitors (MLCs) for EC cooling. Intrinsic cooling powers of 25.9 kW kg−1 are predicted for an optimised MLC based on PVDF-TrFE with Ag electrodes.

No description available.