This thesis focuses mostly on investigating different potential applications of meta-transmission line (TL), particularly composite right/left handed (CRLH) TL, and analyzing some new phenomena and applications of meta-TL, mostly left-handed (LH) TL. Realization principle will also be studied.   First, the fundamental electromagnetic properties of propagation in the presence of left-handed material (LHM) are illustrated. The transmission line approach for LHM design is described together with a brief review of the transmission line theory. As a generalized model for LHM TL, CRLH TL provides very unique phase response, such as dual-band operation, bandwidth enhancement, nonlinear dispersion, and the existence of critical frequency with zero phase velocity. Based on these properties, some novel applications of the existing CRLH transmission lines are then given, including a notch filter, a diplexer, a broadband phase shifter, a broadband balun, and a dual band rat-ring coupler. In the design of notch filters and diplexers, CRLH TL shunt stub is utilized to provide high frequency selectivity due to the existence of critical frequency with zero phase velocity. The proposed wideband Wilkinson balun, which comprises of one section of conventional transmission lines and one section of CRLH-TL, is shown to have a 180°±10° bandwidth of 2.12 GHz centered at 1.5 GHz. In the analysis of the dual band rat-ring couplers, a generalized formulation of the requirements about impedances and electrical length of the branches are derived, and as an example, a compact dual-band rat-race coupler is designed utilizing the balanced CRLH TL. Furthermore, a low pass filter is also proposed and designed based on a single (epsilon) negative coplanar waveguide (CPW).Various principles to realize meta-transmission lines are investigated. The main conclusions are listed below:Ÿ         Dual composite right/left handed (D-CRLH) transmission line, which is the dual structure of conventional CRLH TL, shows opposite handedness in the high frequencies and low frequencies with CRLH TL. Meanwhile, in the practical implementation, D-CRLH TL always shows a sharp stopband. A notch filter and a dual-band balun are designed based on D-CRLH TL. Ÿ         The lattice type transmission line (LT-TL) shows the same magnitude response with the conventional right-handed (RH) TL, but a constant phase difference in the phase response over a wide frequency band. A wideband rat-race coupler is proposed as an application of the LT-TL. Ÿ         Finger-shorted interdigital capacitors (FSIDCs) are analyzed and it is shown that FSIDC alone can act as a left-handed transmission line. The value of the reactive elements (inductors and capacitors) in the equivalent circuit model is determined by the dimensions of FSIDC. The relationship between them is analyzed.Later, transmission line loaded with negative-impedance-converted inductors and capacitors is illustrated as the first non-dispersive LH transmission line. The design of a negative series impedance converter is given in detail and a wideband power divider is designed as a potential application of the newly proposed meta-transmission lines in is also given. The final part of the thesis focuses on the study of microstrip lines loaded with complementary split ring resonators (SRRs). An equivalent circuit is made for this structure. The circuit model is verified by the experimental results of cases with different periodic lengths. Thereafter, a meander line split ring resonator (MLSRR) is presented. It shows dual band property and the miniature prototypes of complementary MLSRR loaded transmission lines are fabricated. By comparing the resonance frequencies of complementary MLSRR and multiple SRR, it is shown that the complementary MLSRR is very compact. C-MLSRR is applied in rejecting unnecessary frequencies in the ultra wideband antennas. / QC 20100720

A novel photonic frequency discriminator has been developed. The discriminator utilizes a Mach Zehnder interferometer-assisted ring resonator to achieve enhanced linearity. A numerical frequency-domain two-tone test is performed to evaluate the unique design of the discriminator, particularly for suppression of the third order intermodulation distortion. The discriminator is switchable between linear-intensity and linear-field regimes by adjusting a phase delay on one arm of the Mach Zehnder interferometer. Through the simulation, the linear<intensity discriminator is shown to be advantageous. The discriminator is an optical ring resonator-Mach Zehnder interferometer synthesized passive filter. The ring resonator is made of Arsenic trisulfide (As2S3) and the bus waveguide is a Titanium<diffused Lithium niobate (LiNbO3) waveguide. This As2S3 ring-on-Ti:LiNbO3 hybrid structure offers electro-optic tunability of the device owing to a strong electro-optic effect of the substrate material. A large optical confinement factor achieved by vertical integration of the As2S3 strip waveguide on a LiNbO3 substrate enables a low loss ring resonator. The Mach Zehnder interferometer is formed by the optical path length difference of the birefringent LiNbO3 substrate instead of a physical Y-branch structure, which makes the fabrication tolerances relaxed. In order for this highly birefringent device to be characterized, each polarization mode must be measured separately. A novel algorithm which can measure the wavelength-swept Jones matrix including its phase response is devised. The efficacy of the algorithm is demonstrated by characterizing a ring resonator. Finally, the fabricated discriminator is fully characterized using the algorithm.

Advancing the field of nanotechnology to incorporate the unique properties observed at the nanoscale into functional devices has become a major scientific thrust of the 21st century. New fabrication tools and assembly techniques are required to design and manufacture devices based on one-dimensional nanostructures. Three techniques for manipulating nanomaterials post-synthesis have been developed. Two of them involve direct contact manipulation through the utilization of a physical probe. The third uses optically generated surface acoustic waves to reproducibly control and assemble one-dimensional nanostructures into desired locations. The nature of the third technique is non-contact and limits contamination and defects from being introduced into a device by manipulation. While the effective manipulation of individual nanostructures into device components is important for building functional nanosystems, commercialization is limited by this one-device-at-a-time process. A new approach to nanostructure synthesis was also developed to site-specifically nucleate and grow nanowires between two electrodes. Integrating synthesis directly with prefabricated device architectures leads to the possible mass production of NEMS, MEMS and CMOS systems based upon one-dimensional nanomaterials. The above processes have been pursued to utilize piezoelectric ZnO nanobelts for applications in high frequency electronic filtering as well as biological and chemical sensing. The high quality, single crystal, faceted nature of these materials make them ideal candidates for studying their properties through the designs of a bulk acoustic resonator. The first ever piezoelectric bulk acoustic resonator based on bottom-up synthesized belts will be demonstrated. Initial results are promising and new designs are implemented to scale the device to sub-micron dimensions. Multiple models will be developed to assist with design and testing. Some of models presented will help verify experimental results while others will demonstrate some of the problems plaguing further investigations.

The objective of the work presented in this thesis is to implement high-Q silicon capacitive micromechanical resonators operating in the HF, VHF and UHF frequency bands. Several variations of a fully silicon-based bulk micromachining fabrication process referred to as HARPSS have been developed, characterized and optimized to overcome most of the challenges facing application of such devices as manufacturable electronic components. Several micromechanical structures for implementation of high performance capacitive silicon resonators covering various frequency ranges have been developed under this work. Design criteria and electromechanical modeling of such devices is presented. Under this work, HF and VHF resonators with quality factors in the tens of thousands and RF-compatible equivalent electrical impedances have been implemented successfully. Resonance frequencies in the GHz range with quality factors of a few thousands and lowest motional impedances reported for capacitive resonators to date have been achieved. Several resonator coupling techniques for implementation of higher order resonant systems with possibility of extension to highly selective bandpass filters have been investigated and practically demonstrated. Finally, a wafer-level vacuum sealing technique applicable to such resonators has been developed and its reliability and hermeticity is characterized.

The presented work aims to optimize the performance of piezoresistive cantilevers in cases where the output signal originates either from a static deflection of the cantilever or from the dynamic (resonance) characteristic of the beam. Based on a new stress concentration technique, which utilizes silicon beams and wires embedded in the cantilever, the force sensitivity of the cantilever is increased up to 8 fold with only about a 15% decrease in the cantilever stiffness. Moreover, the developed stress-concentrating cantilevers show almost the same resonance characteristic as conventional cantilevers. The focus of the second part of the present work is to provide guidelines for designing rectangular silicon cantilever beams to achieve maximum quality factors for the fundamental and higher flexural resonance at atmospheric pressure. The applied methodology is based on experimental data acquisition of resonance characteristics of silicon cantilevers, combined with modification of analytical damping models to match the measurement data. To this end, rectangular silicon cantilever beams with thicknesses of 5, 7, 8, 11 and 17 um and lengths and widths ranging from 70 to 1050 um and 80 to 230 um, respectively, have been fabricated and tested. To better describe the experimental data, modified models for air damping have been developed. Moreover, to better understand the damping mechanisms in a resonant cantilever system, analytical models have been developed to describe the cantilever effective mass in any flexural resonance mode. To be able to extract reliable Q-factor data for low signal-to-noise ratios, a new iterative curve fitting technique is developed and implemented. To address the challenge of frequency drift in (mass-sensitive) resonant sensors, and especially cantilever-based devices, the last part of the research deals with a novel compensation technique to cancel the unwanted environmental effects (e.g., temperature and humidity). This technique is based on exploring the resonance frequency difference of two flexural modes. Experimental data show improvements in temperature and humidity coefficients of frequency from -19.5 to 0.2 ppm/˚C and from 0.7 to -0.03 ppm/%RH, respectively. The last part of the work also aims on techniques to enhance or suppress the flexural vibration amplitude in desired overtones.

Universiẗat, Diss., 2002--Mainz.

Dielectric resonator antenna (DRA) technologies are applicable to a wide variety of mobile wireless communication systems. The principal energy loss mechanism for this type of antenna is the dielectric loss, and then using modern ceramic materials, this may be very low. These antennas are typically of small size, with a high radiation efficiency, often above 95%; they deliver wide bandwidths, and possess a high power handling capability. The principal objectives of this thesis are to investigate and design DRA for low profile personal and nomadic communications applications for a wide variety of spectrum requirements: including DCS, PCS, UMTS, WLAN, UWB applications. X-band and part of Ku band applications are also considered. General and specific techniques for bandwidth expansion, diversity performance and balanced operation have been investigated through detailed simulation models, and physical prototyping. The first major design to be realized is a new broadband DRA operating from 1.15GHz to 6GHz, which has the potential to cover most of the existing mobile service bands. This antenna design employs a printed crescent shaped monopole, and a defected cylindrical DRA. The broad impedance bandwidth of this antenna is achieved by loading the crescent shaped radiator of the monopole with a ceramic material with a permittivity of 81. The antenna volume is 57.0  37.5  5.8 mm3, which in conjunction with the general performance parameters makes this antenna a potential candidate for mobile handset applications. The next class of antenna to be discussed is a novel offset slot-fed broadband DRA assembly. The optimised structure consists of two asymmetrically located cylindrical DRA, with a rectangular slot feed mechanism. Initially, designed for the frequency range from 9GHz to 12GHz, it was found that further spectral improvements were possible, leading to coverage from 8.5GHz to 17GHz. Finally, a new low cost dual-segmented S-slot coupled dielectric resonator antenna design is proposed for wideband applications in the X-band region, covering 7.66GHz to 11.2GHz bandwidth. The effective antenna volume is 30.0 x 25.0 x 0.8 mm3. The DR segments may be located on the same side, or on opposite sides, of the substrate. The end of these configurations results in an improved diversity performance.

Title: Magnetic nanostructures for recording and optical sensors Author: Eva Lišková Department: Institute of Physics, Charles University Supervisor: Prof. Ing. Štefan Višňovský, DrSc. Abstract: Magneto-optical (MO) spectra of multilayered structures with enhanced MO effect were studied using the polar and longitudinal Kerr spectroscopy with oblique angle of light incidence in the photon energy range 1.2 eV to 5 eV. The samples with Fabry- Perot cavity like architecture, were modeled using Yeh matrix formalism. Two sets of samples, with composition FeF2/Fe/FeF2 and AlN/Fe/AlN, were prepared by molecular beam epitaxy and sputtering. The relations were studied between the position of the enhanced peak in the MO spectra and the structure. Second part of this work was devoted to the Pt/Co/Pt structures and the influence of the ion implantation on MO spectra and structural composition. The studied multilayer structures present interest for MO sensor and memory applications. Keywords: Magneto-optical Kerr effect, Magneto-optical sensor, Fabry-Perot resonator, Ion implantation

Les MEMS et NEMS résonants sont d'excellents candidats pour la réalisation de systèmes de détection de gaz haute résolution et faible couts ayant des applications dans les domaines de la sécurité, la défense, l'environnement et la santé. Cependant, la question du choix des techniques de transduction est toujours largement débattue. La transduction piézoélectrique pourrait être avantageusement exploitée mais elle est encore peu connue à l'échelle nanométrique. L'objectif de cette thèse est donc de progresser vers la réalisation de capteur de gaz à haute résolution à l'aide résonateurs à base de micro / nano poutres piézoélectriques en couvrant la chaîne de prototypage complète depuis les techniques de dépôt des matériaux jusqu'à l'expérience de preuve de principe de mesure de gaz. Pour cela, notre première contribution concerne la modélisation analytique des performances et l'optimisation, design et système, d'un capteur de gaz à base de poutres résonantes piézoélectriques. En particulier, nous démontrons que la diminution de l'épaisseur du film piézoélectrique actif sous la barre des 100 nm permet d'atteindre les meilleures performances. La deuxième contribution concerne la fabrication, la caractérisation et la démonstration des performances capteur de poutres résonantes de 80 μm de long exploitant un film piézoélectrique en AlN de 50 nm d'épais. Ainsi nous avons démontré expérimentalement la stabilité fréquentielle exceptionnelle de ces dispositifs atteignant des déviations standard de l'ordre de 〖10〗^(-8), au niveau de l’état de l'art. Ainsi, ils permettent la détection de vapeurs Di -Methyl -méthyl- phosphonates, un simulateur de gaz sarin, avec des concentrations aussi faibles que 10 ppb. Bien que le niveau d'intégration de notre système de détection ne soit pas suffisant, ces résultats prouvent le fort potentiel de ces résonateurs cantilever piézoélectriques pour un développement industriel futur. / Resonant MEMS and NEMS are excellent candidate for the realization of low cost and high resolution gas sensing systems that have several applications in security, defense, and environment and health care domains. However, the question of the transduction technique used to couple micro or nano scale signals to the macro scale is still a key issue. Piezoelectric transduction can be advantageously exploited but has been rarely studied at the nano-scale. The objective of this PhD is thus to progress toward the realization of high-resolution gas sensor using piezoelectric micro/nano cantilevers resonators and cover the whole prototyping chain from device fabrication to proof of principle experiment. Our first contribution in this research relates the analytical modeling of the sensing performance and the system and design optimization. In particular we demonstrate that decreasing the piezoelectric active film thickness below 100 nm is particularly beneficial. The second contribution relates the fabrication, characterization and demonstration of the high sensing performances of 80 μm long cantilevers embedding a 50 nm thick piezoelectric AlN film for transduction. These devices exhibit state of the art performances in terms of resonance frequency deviation down to the 〖10〗^(-8) range. They allow thus the detection of Di-Methyl-Methyl-Phosphonate vapors, a sarin gas simulant, with concentration as low as 10 ppb. Although the level of integration of our sensing system is not sufficient for real life application, these results prove the high potential of these piezoelectric cantilever resonators for future industrial development.

The objectives of this work are to review, investigate and model the microwave planar filters of the modern wireless communication system. The recent main stream of microwave filters are classified and discussed separately. Various microwave filters with detailed applications are investigated in terms of their geometrical structures and operational performances. A comprehensive theoretical study of microwave filters is presented. The main types of microwave filters including the basic low-pass filters such as Butterworth and Chebyshev filters are fully analysed and described in detail. The transformation from low-pass prototype filters to high-pass filters, band-pass filters and band-stop filters are illustrated and introduced. Research work on stepped impedance resonator (SIR) and asymmetric stepped impedance resonator (ASIR) structure is presented. The characteristics of λg/4, λg/2 and λg (λg is the guided wavelength of the fundamental frequency in the free space) type SIR resonators, and the characteristic of asymmetric SIR resonator are categorized and investigated. Based on the content mentioned above, novel multi-standard high performance asymmetric stepped impedance resonator single-wideband and dual-wideband filters with wide stopbands are proposed. The methodologies to realize wide passband and wide stop-band filters are detailed. In addition, multi-standard high performance triplewideband, quadruple-wideband and quint-wideband filters are suggested and studied. The measurement results for all prototype filters agree well with the theoretical predictions and simulated results from Ansoft HFSS software. The featured broad bandwidths over single/multiple applicable frequency bands and the high performances of the proposed filters make them very promising for applications in future multistandard wireless communication.