Thermoelektrische Phänomene können in Nanomaterialien im Vergleich zum Volumenmaterial stark modifiziert werden. Die Bestimmung der elektrischen Leitfähigkeit, des absoluten Seebeck-Koeffizienten (S) und der Wärmeleitfähigkeit ist eine wesentliche Herausforderung für die Messtechnik in Hinblick auf Mikro- und Nanostrukturen aufgrund dessen, dass die Transporteigenschaften vom Volumenmaterial sich durch Oberflächen- und Einschränkungseffekte verändern können. Im Rahmen dieser Abschlussarbeit wird der Einfluss von Größeneffekten auf die thermoelektrischen Eigenschaften von dünnen Platinschichten untersucht und mit dem Volumenmaterial verglichen. Dafür wurde eine Messplattform als standardisierte Methode entwickelt, um S einer dünnen Schicht zu bestimmen. Strukturelle Eigenschaften wie Schichtdicke und Korngröße werden variiert. Grenz- und Oberflächenstreuung reduzieren S der dünnen Schichten im Vergleich zum Volumenmaterial. Außerdem wird eine Methode demonstriert um S von einzelnen metallischen Nanodrähten zu bestimmen. Für hochreine und einkristalline Silber-Nanodrähte wird der Einfluss von Nanostrukturierung auf die Temperaturabhängigkeit von S gezeigt. Ein Modell ermöglicht die eindeutige Zerlegung des temperaturabhängigen S von Platin und Silber in einen Thermodiffusions- und Phononen-Drag-Anteil. Des Weiteren werden die thermoelektrischen Transporteigenschaften von einzelnen auf Bismut-basierenden Kern/Hülle-Nanodrähten untersucht. Der Einfluss des Hüllenmaterials (Tellur oder Titandioxid) und der räumlichen Dimension des Nanodrahts auf die Transporteigenschaften wird diskutiert. Streuung an Oberflächen, Einkerbungen und Grenzflächen zwischen dem Kern und der Hülle reduzieren die elektrische und thermische Leitfähigkeit. Eine Druckverformung induziert durch die Hülle kann zu einer Bandöffnung bei Bismut führen, sodass S gesteigert werden kann. Das Kern/Hülle-System zeigt in eine Richtung, um die thermoelektrischen Eigenschaften von Bismut erfolgreich anzupassen. / Thermoelectric phenomena can be strongly modified in nanomaterials compared to the bulk. The determination of the electrical conductivity, the absolute Seebeck coefficient (S) and the thermal conductivity is a major challenge for metrology with respect to micro- and nanostructures because the transport properties of the bulk may change due to surface and confinement effects. Within the scope of this thesis, the influence of size effects on the thermoelectric properties of thin platinum films is investigated and compared to the bulk. For this reason, a measurement platform was developed as a standardized method to determine S of a thin film. Structural properties, like film thickness and grain size, are varied. Boundary and surface scattering reduce S of the thin films compared to the bulk. In addition, a method is demonstrated to determine S of individual metallic nanowires. For highly pure and single crystalline silver nanowires, the influence of nanopatterning on the temperature dependence of S is shown. A model allows the distinct decomposition of the temperature-dependent S of platinum and silver into a thermodiffusion and phonon drag contribution. Furthermore, the thermoelectric transport properties of individual bismuth-based core/shell nanowires are investigated. The influence of the shell material (tellurium or titanium dioxide) and spatial dimension of the nanowire on the transport properties are discussed. Scattering at surfaces, indentations and interfaces between the core and the shell reduces the electrical and the thermal conductivity. A compressive strain induced by the shell can lead to a band opening of bismuth increasing S. The core/shell system points towards a route to successfully tailor the thermoelectric properties of bismuth.

Die vorliegende Arbeit ist eine umfassende Studie über das Wachstum mittels Molekularstrahlepitaxie (MBE) und die gemessenen Seebeck Koeffizienten und Lochtransport Eigenschaften von p‑Typ Oxiden, eine Materialklasse welche die optische Transparenz und die einstellbare Leitfähigkeit verbindet. Insbesondere, Nickeloxid (NiO) und Zinnmonoxid (SnO) wurden mittels plasmaunterstützter MBE unter Einsatz von einer Metall‑Effusionszelle und einem Sauerstoffplasma gewachsen. Für das NiO Wachstum wurden vor allem die Wachstumsgrenzen bei hohen Temperaturen festgelegt, welche von der Substratstabilität im Falle von Magnesiumoxid und Galliumnitrid abhängen. Es wird die Möglichkeit der Qualitätsbewertung mittels Ramanspektroskopie für Natriumchlorid-Strukturen gezeigt. Untersuchung der NiO Dotierung durch Oberflächen-Akzeptoren und der damit verbundenen Oberflächen‑Loch‑Anreicherungsschicht offenbart eine neue Dotierungsmöglichkeit für p‑leitende Oxide im Allgemeinen. Die metastabile Phase des SnO wird mittels PAMBE unter Verwendung bekannter Wachstumskinetik von Zinndioxid und verschiedener in‑situ Methoden stabilisiert, die anwendungsrelevante thermische Stabilität wird untersucht. Anschließende ex‑situ Charakterisierungen durch XRD und Ramanspektroskopie identifizieren das kleine Wachstumsfenster für das epitaktische Wachstum von SnO. Elektrische Messungen bestätigen die p‑Typ Ladungsträger mit vielversprechenden Löcherbeweglichkeiten welche auch für Hall Messungen zugänglich sind. Temperaturabhängige Hall Messungen zeigen einen bandähnlichen Transport welcher auf eine hohe Qualität der gewachsenen Schichten hindeutet. Die Funktionalität der gewachsenen Schichten wird durch verschiedene Anwendungen nachgewiesen. Zum Beispiel werden pn‑Heteroübergänge wurden durch das heteroepitaktische Wachstum der SnO Schichten auf einem Galliumoxid-Substrat erlangt. Die ersten bisher berichteten SnO-basierten pn‑Übergänge mit einem Idealitätsfaktor unter zwei wurden erreicht. / This thesis presents a comprehensive study on the growth by molecular beam epitaxy (MBE) and the measured Seebeck coefficients and hole transport properties of p‑type oxides, a material class which combines transparency and tunable conductivity. Specifically, Nickel oxide (NiO) and tin monoxide (SnO) were grown by plasma‑assisted MBE using a metal effusion cell and an oxygen plasma. For NiO growth, the focus lies on high temperature growth limits which were determined by the substrate stability of magnesium oxide and gallium nitride. Quality evaluation by Raman spectroscopy for rock‑salt crystal structures is demonstrated. Investigations of NiO doping by surface acceptors and the related surface hole accumulation layer reveal a new doping possibility for p‑type oxides in general. The meta‑stable SnO is stabilized by PAMBE utilizing known growth kinetics of tin dioxide and various in‑situ methods, its application-relevant thermal stability is investigated. Following ex‑situ characterizations by XRD and Raman spectroscopy identify secondary phases and a small growth window for the epitaxial growth of SnO. Electrical measurements confirm the p‑type carriers with promising hole mobilities accessible to Hall measurements. Temperature dependent Hall measurements show band‑like transport indicating a high quality of the grown layers. The functionality of the grown layers is proven by various applications. For example, pn‑heterojunctions were achieved by heteroepitaxial growth of the SnO layers on gallium oxide substrates. The first reported SnO based pn‑junction with an ideality factor below two is accomplished.

Increasing interest in an effciency enhancement of existing energy sources led to an extended research in the field of thermoelectrics. Especially skutterudites with their high power factor (electric conductivity times Seebeck coefficient squared) are suitable thermoelectric materials. However, a further improvement of their thermoelectric properties is necessary. The relatively high thermal conductivity can be decreased by introducing loosely bound guest ions, whereas atom substitution or nanostructuring (as thin films) could yield an increased power factor. The present work proves the feasibility to deposit single phase skutterudite thin films by MBE technique. In this regard CoSby and FeSby film series were deposited with three different methods: i) codeposition at elevated temperatures, ii) codeposition at room temperature followed by post-annealing, and iii) modulated elemental reactant method. The structural and thermoelectric properties of these films were investigated by taking the thermal stability of the film and the substrate properties into account. Compared to the stoichiometric Sb content of skutterudites of 75 at.%, a small excess of Sb is necessary for achieving single phase skutterudite films. It was found, that the deposited single phase CoSb3 films reveal bipolar conduction (and therefore a low Seebeck coefficient), whereas FeSb3 films show p-type conduction and very promising power factors at room temperature. The need of substrates with a low thermal conductivity and a suitable thermal expansion coefficient is also demonstrated. A high thermal conductivity influences the measurements of the Seebeck coefficient and the obtained values will be underestimated by thermal shortening of the film by the substrate. If the thermal expansion coefficient of film and substrate differ strongly from each other, crack formation at the film surface was observed. Furthermore, the realization of controlled doping by substitution as well as the incorporation of guest ions was successfully shown. Hence, this work is a good starting point for designing skutterudite based thin film structures. Two successful examples for such structures are given: i) a thickness series, where a strong decrease of the resistivity was observed for films with a thickness lower than 10nm, and ii) a FexCo1-xSb3 gradient film, for which the gradient was maintained even at an annealing temperature of 400°C.

Increasing interest in an effciency enhancement of existing energy sources led to an extended research in the field of thermoelectrics. Especially skutterudites with their high power factor (electric conductivity times Seebeck coefficient squared) are suitable thermoelectric materials. However, a further improvement of their thermoelectric properties is necessary. The relatively high thermal conductivity can be decreased by introducing loosely bound guest ions, whereas atom substitution or nanostructuring (as thin films) could yield an increased power factor. The present work proves the feasibility to deposit single phase skutterudite thin films by MBE technique. In this regard CoSby and FeSby film series were deposited with three different methods: i) codeposition at elevated temperatures, ii) codeposition at room temperature followed by post-annealing, and iii) modulated elemental reactant method. The structural and thermoelectric properties of these films were investigated by taking the thermal stability of the film and the substrate properties into account. Compared to the stoichiometric Sb content of skutterudites of 75 at.%, a small excess of Sb is necessary for achieving single phase skutterudite films. It was found, that the deposited single phase CoSb3 films reveal bipolar conduction (and therefore a low Seebeck coefficient), whereas FeSb3 films show p-type conduction and very promising power factors at room temperature. The need of substrates with a low thermal conductivity and a suitable thermal expansion coefficient is also demonstrated. A high thermal conductivity influences the measurements of the Seebeck coefficient and the obtained values will be underestimated by thermal shortening of the film by the substrate. If the thermal expansion coefficient of film and substrate differ strongly from each other, crack formation at the film surface was observed. Furthermore, the realization of controlled doping by substitution as well as the incorporation of guest ions was successfully shown. Hence, this work is a good starting point for designing skutterudite based thin film structures. Two successful examples for such structures are given: i) a thickness series, where a strong decrease of the resistivity was observed for films with a thickness lower than 10nm, and ii) a FexCo1-xSb3 gradient film, for which the gradient was maintained even at an annealing temperature of 400°C.:Contents 1 Introduction 2 Nanostructured thermoelectric materials 2.1 Thermoelectric materials and ZT 2.2 Recent developments in improving ZT in thin films 3 Thermoelectric transport theory 3.1 Electronic transport coefficients 3.2 Lattice thermal conductivity 4 Skutterudites as promising thermoelectric material 4.1 CoSb3 4.1.1 Structural properties of skutterudites 4.1.2 Band structure of CoSb3 and density of states 4.1.3 Thermoelectric properties of CoSb3 4.1.4 Synthesis of CoSb3 thin films 4.2 FeSb3 4.2.1 Structural and thermoelectric properties of FeSb3 thin films 4.2.2 Synthesis of FeSb3 thin films 5 Experimental methods 5.1 Basic methods for structural characterization 5.2 Electric characterization: Resistivity and Hall measurements using van der Pauw geometry 5.3 Thermoelectric characterization (Seebeck coefficient) 5.4 Thermal characterization methods 6 Deposition of skutterudite thin films 6.1 Deposition chamber and deposition parameters 6.2 Deposition methods 6.3 Composition control of skutterudite films 7 Control of structural properties by the used deposition method 7.1 Structural properties of CoSb3 thin films 7.1.1 Crystallization characteristics of CoSb3 films 7.1.2 Comparison of films deposited with different deposition methods 7.1.3 Influence of different deposition parameters on the film properties 7.2 Structural properties of FeSb3 thin films 7.2.1 Crystallization behaviour 7.2.2 Structural properties of post-annealed Fe-Sb films prepared by codeposition 7.2.3 Influence of the heating rate on the film properties 8 CoSb3 and FeSb3 composition series 8.1 CoSby composition series 8.1.1 Films deposited at elevated temperatures 8.1.2 Annealed films 8.2 FeSby composition series 9 Influence of various substrates on the film properties 9.1 Substrate influence on the film morphology 9.2 Substrate influence on thermoelectric properties and measurements 10 FexCo1-xSb3 - controlled doping by substitution of Co with Fe 10.1 Properties of codeposited FexCo1-xSb3 films 10.2 Properties of FexCo1-xSb3 films deposited via MERM 11 Filled CoSb3 thin films 12 Examples for nanostructured thin film approaches 12.1 CoSb3 thickness series 12.2 FexCo1-xSb3 gradient films 13 Summary and Outlook