Formaldehyde-based adhesives have been reported to be detrimental to health. Petrochemical-based adhesives are non-renewable, limited and costly. Therefore, the improvement of environmental-friendly adhesive from natural agricultural products has awakened noteworthy attention. A novel adhesive for wood application was successfully prepared with enhanced shear strength and water resistance. The Fourier transmform infrared spectra showed the surface functionalities of the functionalized carbon nanotubes (FCNTs) and soy protein isolate nanocomposite adhesive. The attachment of carboxylic functional group on the surface of the carbon nanotubes (CNTs) after purification contributed to the effective dispersion of the CNTs in the nanocomposite adhesive. Hence, enhanced properties of FCNTs were successfully transferred into the SPI/CNTs nanocomposite adhesive. These unique functionalities on FCNTs however, improved the mechanical properties of the adhesive. The shear strength and water resistance of SPI/FCNTs was higher than that of the SPI/CNTs. SEM images showed the homogenous dispersion of CNTs in the SPI/CNTs nanocomposite adhesive. The carbon nanotubes were distributed uniformly in the soy protein adhesive with no noticeable clusters at relatively reduced fractions of CNTs as shown in the SEM images, which resulted into better adhesion on wood surface. Mechanical (shear) mixing and ultrasonication with 30 minutes of shear mixing both showed an improved dispersion of CNTs in the soy protein matrix. However, ultrasonication method of dispersion showed higher tensile shear strength and water resistance than in mechanical (shear) mixing method. Thermogravimetric analysis of the samples also showed that the CNTs incorporated increases the thermal stability of the nanocomposite adhesive at higher loading fraction. Incorporation of CNTs into soy protein isolate adhesive improved both the shear strength and water resistance of the adhesive prepared at a relatively reduced concentration of 0.3%.The result showed that tensile shear strength of SPI/FCNTs adhesive was 0.8 MPa and 7.25MPa at dry and wet state respectively, while SPI/CNTs adhesive had 6.91 MPa and 5.48MPa at dry and wet state respectively. There was over 100% increase in shear strength both at dry and wet state compared to the pure SPI adhesive. The 19% decrease in value of the new adhesive developed compared to the minimum value of ≥10MPa of European standard for interior wood application may be attributed to the presence of metallic particles remaining after purification of CNTs. The presence of metallic particles will prevent the proper penetration of the adhesive into the wood substrate. The type of wood used in this study as well as the processing parameters could also result into lower value compared to the value of European standard. Therefore, optimization of the processing parameter as well as the conversion of carboxylic acid group on the surface of the CNTs into acyl chloride group may be employed in future investigation. However, the preparation of new nanocomposite adhesive from soy protein isolate will replace the formaldehyde and petrochemical adhesive in the market and be of useful application in the wood industry. / Civil and Chemical Engineering / M. Tech. (Chemical Engineering)

Dans le domaine pharmaceutique, la voie orale demeure la voie d’administration de prédilection, car plus simple et mieux acceptée par les patients. Cependant, ce mode d’administration pose problème pour de nombreux principes actifs (PA) présentant une faible solubilité, une faible perméabilité et/ou une instabilité dans l’environnement gastro-intestinal. Leur micro-encapsulation dans des matrices polymériques peut permettre d’y répondre, notamment si les microparticules générées résistent aux environnements rencontrés lors du tractus gastro-intestinal et jouent alors un rôle protecteur, tant pour le principe actif que pour les muqueuses rencontrées. La recherche de nouveaux excipients, issus des agro-ressources tels que les polymères naturels, est en plein essor. Les protéines végétales, grâce à leurs propriétés fonctionnelles telles qu’une bonne solubilité, une viscosité relativement basse, et des propriétés émulsifiantes et filmogènes, représentent des candidats privilégiés. De plus, la grande diversité de leurs groupements fonctionnels permet d’envisager des modifications chimiques ou enzymatiques variées. L’objectif de ce travail était d’étudier l’intérêt de la protéine de soja en tant que matériau enrobant de principes actifs pharmaceutiques destinés à la voie orale, et plus particulièrement en tant que candidat pour l’élaboration de formes gastro-résistantes. Un isolat protéique de soja (SPI) été utilisé comme matière enrobante et l’atomisation comme procédé. L’ibuprofène, anti-inflammatoire non stéroïdien, a été choisi comme molécule modèle du fait de sa faible solubilité nécessitant une amélioration de sa biodisponibilité, et de ses effets indésirables gastriques nécessitant une mise en forme entérique. Deux modifications chimiques des protéines (l’acylation et la succinylation) ont été étudiées dans le but de modifier la solubilité de la protéine de soja. Ces modifications ont été effectuées dans le respect des principes de la Chimie Verte, notamment en absence de solvant organique. Les microcapsules obtenues par atomisation ont été caractérisées en termes de taux et efficacité d'encapsulation, morphologie et distribution de tailles des particules, état physique du PA encapsulé et capacité de libération en milieu gastrique et intestinal simulé. Les résultats obtenus ont permis de valider l’intérêt des modifications chimiques de la protéine de soja pour moduler les cinétiques de libération d’actif. Les modifications chimiques sont apparues particulièrement adaptées pour l’encapsulation de principes actifs hydrophobes, et ont permis de l’obtention de cinétiques de libération d’ibuprofène ralenties à pH acide (gastrique). La dernière partie de ce travail a permis de valider cette dernière hypothèse par la réalisation de formes gastro-résistantes sur le modèle des comprimés MUPS (multiple unit pellet system). Les résultats de ce travail exploratoire démontrent que les protéines de soja, associées à un procédé de mise en forme multi-particulaire couplé à de la compression directe, peuvent constituer une alternative biosourcée, respectueuse de l’environnement (manipulation en solvant aqueux, temps de séchage et étapes de compression réduits) et sûre à l’enrobage utilisé dans les formes gastro-résistantes traditionnelles. / In the pharmaceutical field, the oral route remains the preferred route of administration because it is simpler and better accepted by patients. However, this mode of administration is problematic for many active pharmaceutical ingredients (API) with low solubility, low permeability and/or instability in the gastrointestinal environment. Their microencapsulation in polymeric matrices can make them able to respond to these factors, especially if the microparticles generated resist the environments encountered during the gastrointestinal tract and then play a protective role, both for the API and for the mucous membranes encountered. The search for new excipients, from agroresources such as natural polymers, is booming. Vegetable proteins, thanks to their functional properties such as good solubility, relatively low viscosity, and emulsifying and film-forming properties, are preferred candidates. In addition, the great diversity of their functional groups makes it possible to envisage various chemical or enzymatic modifications. The aim of this work was to study the interest of soy protein as a coating material for API intended for the oral route, and more particularly as a candidate for the development of gastro-resistant forms. A soy protein isolate (SPI) was used as a coating material and the atomization as a process. Ibuprofen, a nonsteroidal anti-inflammatory drug, was chosen as a model molecule because of its low solubility requiring an improvement in its bioavailability, and its gastric side effects requiring an enteric shaping. Two chemical modifications of proteins (acylation and succinylation) have been studied in order to modify the solubility of the soy protein. These modifications were carried out in accordance with the principles of Green Chemistry, especially in the absence of organic solvent. The microcapsules obtained by spray-drying were characterized in terms of rate and encapsulation efficiency, morphology and size distribution of the particles, physical state of the encapsulated API and capacity of release in simulated gastric and intestinal medium. The results obtained validated the interest of the chemical modifications of the soy protein to modulate the release kinetics of API. The chemical modifications appeared particularly suitable for the encapsulation of hydrophobic active ingredients, and allowed to obtain ibuprofen release kinetics decreased to acidic pH (gastric). The last part of this work allowed to validate this last hypothesis by the realization of gastro-resistant forms on the model of MUPS tablets (multiple unit pellet system). The results of this exploratory work demonstrate that soy protein, combined with a multiparticle shaping process coupled with direct compression, can be a biosourced, environmentally friendly alternative (aqueous solvent handling, drying and compression steps reduced) and confident to the coating used in traditional gastroresistant forms.

Des solutions d'isolat de protéine de lactosérum (WPI) et d'isolat de protéine de soja (SPI) ont été chauffées à différentes concentrations en protéines conduisant à la formation d'agrégats fractals polydisperses de taille moyenne variable. Lastructure des solutions a été analysée par diffusion de la lumière en fonction de la concentration en protéine. La compressibilité osmotique et la longueur de corrélation dynamique diminuent quand la concentration augmente deviennent indépendantes de la taille initiale des agrégats pour les suspensions denses. Pour une taille d'agrégat donnée, la viscosité augmente initialement exponentiellement avec la concentration croissante puis diverge. Plus lesagrégats sont grands, plus l’augmentation de la viscosité apparaît à des concentrations faibles. La dépendance avec la concentration de la viscosité des solutions d'agrégats fractals est beaucoup plus forte que celle de microgels. Le comportement de mélanges de différents types d’agrégats (fractals/fractals ; fractals/microgels et WPI/SPI) a étéétudié principalement par rhéologie.Le recouvrement de fluorescence après photoblanchiment (FRAP) a été utilisé pour étudier la diffusion de chaînes de dextran marquées par des fluorophores dans des solutions d’agrégats et des gels de WPI. Une diffusion brownienne estobservée dans des suspensions d’agrégats et des gels faibles formés juste au-delà de Cg avec un coefficient de diffusion (D) qui diminue avec l'augmentation de la concentration mais, avec une dépendance plus faible que celle de la viscosité (). A des concentrations plus élevées, des gels densément réticulés sont formés, ce qui induit une forte diminution de la mobilité des chaînes de dextran. Pour ces systèmes, la recouvrance de la fluorescence est logarithmique avec le temps,suggérant une distribution exponentielle des coefficients de diffusion. La diffusion des chaînes de dextran a également été étudiée en fonction de la concentration en protéines pour les suspensions de trois types d'agrégats de WPI (petits et grands fractals et microgels). / Polydisperse fractal aggregates of varying average sizes were formed when solutions of whey protein isolate and soy protein isolate were heated at different protein concentrations and at neutral pH. The structure of these fractals aggregates solutions was analyzed by light scattering as a function of protein concentration. In dense suspension, the osmotic compressibility and the correlation length decreases with increasing concentration and become independent of the initial aggregate size. In this concentration regime, the aggregates are strongly interpenetrated and can be visualized as a set of "blobs". For a fixed aggregate size, the viscosity initially increases exponentially with increasing concentration and then diverges at the gel point. Larger fractal aggregates show a more important increase of the viscosity with increasing concentration than smaller aggregates, because they are less dense. The increase of the viscosity was much stronger for large fractal aggregates than for homogeneous microgels (microgels were formed by heating the WPI solution in present of CaCl2) of the same size.Dynamic light scattering, rheology and FRAP measurements were performed to investigate mixtures of different type of aggregates of WPI (fractals/fractals, fractals/microgels) and fractals of mixtures of WPI and SPI. Flow measurements were used to characterise the rheological properties of the aggregate suspension whereas Fluorescence recovery after Photobleaching (FRAP) was used to determine the self diffusion of fluorophore-labelled dextrans chains in mixtures over a wide range of concentrations. The results were compared to the concentration dependence of zero shear viscosity, gel stiffness, osmotic compressibility and correlation length. Brownian diffusion of the dextran chains was observed in aggregate suspensions and weak gels formed just above the gel point with a diffusion coefficient that decreased with increasing concentration, but the dependence was weaker than that of the viscosity. At higher concentrations, densely crosslinked gels were formed, which induced a sharp decrease in the mobility of the dextran chains. For these systems, the recovery of fluorescence was logarithmic over time, suggesting an exponential distribution of diffusion coefficients.

Formaldehyde-based adhesives have been reported to be detrimental to health. Petrochemical-based adhesives are non-renewable, limited and costly. Therefore, the improvement of environmental-friendly adhesive from natural agricultural products has awakened noteworthy attention. A novel adhesive for wood application was successfully prepared with enhanced shear strength and water resistance. The Fourier transmform infrared spectra showed the surface functionalities of the functionalized carbon nanotubes (FCNTs) and soy protein isolate nanocomposite adhesive. The attachment of carboxylic functional group on the surface of the carbon nanotubes (CNTs) after purification contributed to the effective dispersion of the CNTs in the nanocomposite adhesive. Hence, enhanced properties of FCNTs were successfully transferred into the SPI/CNTs nanocomposite adhesive. These unique functionalities on FCNTs however, improved the mechanical properties of the adhesive. The shear strength and water resistance of SPI/FCNTs was higher than that of the SPI/CNTs. SEM images showed the homogenous dispersion of CNTs in the SPI/CNTs nanocomposite adhesive. The carbon nanotubes were distributed uniformly in the soy protein adhesive with no noticeable clusters at relatively reduced fractions of CNTs as shown in the SEM images, which resulted into better adhesion on wood surface. Mechanical (shear) mixing and ultrasonication with 30 minutes of shear mixing both showed an improved dispersion of CNTs in the soy protein matrix. However, ultrasonication method of dispersion showed higher tensile shear strength and water resistance than in mechanical (shear) mixing method. Thermogravimetric analysis of the samples also showed that the CNTs incorporated increases the thermal stability of the nanocomposite adhesive at higher loading fraction. Incorporation of CNTs into soy protein isolate adhesive improved both the shear strength and water resistance of the adhesive prepared at a relatively reduced concentration of 0.3%.The result showed that tensile shear strength of SPI/FCNTs adhesive was 0.8 MPa and 7.25MPa at dry and wet state respectively, while SPI/CNTs adhesive had 6.91 MPa and 5.48MPa at dry and wet state respectively. There was over 100% increase in shear strength both at dry and wet state compared to the pure SPI adhesive. The 19% decrease in value of the new adhesive developed compared to the minimum value of ≥10MPa of European standard for interior wood application may be attributed to the presence of metallic particles remaining after purification of CNTs. The presence of metallic particles will prevent the proper penetration of the adhesive into the wood substrate. The type of wood used in this study as well as the processing parameters could also result into lower value compared to the value of European standard. Therefore, optimization of the processing parameter as well as the conversion of carboxylic acid group on the surface of the CNTs into acyl chloride group may be employed in future investigation. However, the preparation of new nanocomposite adhesive from soy protein isolate will replace the formaldehyde and petrochemical adhesive in the market and be of useful application in the wood industry. / Civil and Chemical Engineering / M. Tech. (Chemical Engineering)

Submitted by JÚLIO HEBER SILVA (julioheber@yahoo.com.br) on 2016-11-23T16:13:22Z No. of bitstreams: 2 Dissertação - Mirtza Fúlvia Maggioli - 2014.pdf: 10959485 bytes, checksum: 5397bb78460f4fbc15b15f9f9dd335a5 (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) / Approved for entry into archive by Jaqueline Silva (jtas29@gmail.com) on 2016-11-30T15:44:44Z (GMT) No. of bitstreams: 2 Dissertação - Mirtza Fúlvia Maggioli - 2014.pdf: 10959485 bytes, checksum: 5397bb78460f4fbc15b15f9f9dd335a5 (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) / Made available in DSpace on 2016-11-30T15:44:44Z (GMT). No. of bitstreams: 2 Dissertação - Mirtza Fúlvia Maggioli - 2014.pdf: 10959485 bytes, checksum: 5397bb78460f4fbc15b15f9f9dd335a5 (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) Previous issue date: 2014-05-09 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - CAPES / This work shows the green coffee oil coacervation processes, as core material, in two different systems: whey protein / gum arabic and soy protein / gum arabic, as biopolymer wall. The biopolymers concentration were fixed in 4% (weight / weight) of the emulsion, and the proportion between then was respectively 2:1 and 1,4:1. Different emulsions were made, each one with a different green coffee oil concentration (0%, 10%, 17.5% and 25%) compared with wall materials. From these emulsions with adjusted pH, the system presented phase separation (coacervation). The following system characteristics were studied: maximum interation pHs, emulsions rheological behavior, emulsions sizes, physico-chemical characterization of the phases (coacervate and supernadant), process mass balance, coacervate rheology, microparticles morphology after lyophilization, the powder density, the powder stability and the microencapsulation process efficiency. The results confirmed that there is an optimum range of particle formation, depending on pH. The emulsions presented typical Newtonian fluid behavior and the viscosity increased with incresing the oil concentration. That behavior does not depend on wall materials. It was also observed that wet coacervates were better fitted to Power Law, presenting pseudoplastic behavior. Concentrate soy protein / gum arabic showed thixotropy. The emulsion gout showed an surface average diameter between 2,24 µm e 14,42µm. The microparticles exhibited slightly spherical, rough surface and pores, probably influenced by drying process. The process efficiency showed no dependence on the oil concentration at studied systems. The adsorption isotherms (at 30°C) of the obtained powders were best fitted to the GAB model and the e moisture content of monolayer (xm) for this model were between 2.5% to 5.1% for CPSL and GA microparticles and between 5.1% and 6.1% for IPS and GA / Neste trabalho foram estudados os processos de coacervação complexa de óleo de café verde, como material de recheio, em dois tipos de sistemas: concentrado proteico de soro de leite (CPSL)/ goma arábica (GA) e isolado proteico de soja (IPS) / goma arábica (GA), como biopolímeros de parede. Estes sistemas foram preparados com concentração de biopolímeros fixa em 4% (massa / massa) da emulsão e a proporção entre eles foi respectivamente 2:1 e 1,4:1. Emulsões com diferentes concentrações de óleo de café verde (0%; 10%; 17,5% e 25%), em relação aos materiais de parede, foram preparadas. A partir destas emulsões com os pHs ajustados, o sistema apresentou separação de fases (coacervação). Foram avaliados os pHs de máxima interação entre os pares de biopolímeros estudados, o comportamento reológico das emulsões, o tamanho de gota das emulsões produzidas, a caracterização fisicoquímica das fases (sobrenadante e coacervado), o balanço de massa do processo, a reologia do coacervado, a morfologia das micropartículas após liofilização, a densidade dos pós obtidos, a estabilidade do pó e a eficiência do processo de microencapsulação. Os resultados obtidos confirmaram que existe uma faixa ótima de formação de partículas dependente do pH. As emulsões apresentaram comportamento típico de fluidos newtoniano e a viscosidade aumentou com a concentração de óleo independente dos materiais de parede estudados. Já os coacervados úmidos ajustaram-se melhor à Lei da Potência apresentando comportamento pseudoplástico. Os coacervados de isolado proteico de soja / goma arábica apresentaram tixotropia. As emulsões apresentaram gotas com diâmetro superficial médio entre 2,24 µm e 14,42µm. As micropartículas apresentaram forma levemente esférica, superficie rugosa e com poros provavelmente influenciada pelo processo de secagem. A eficiência do processo não mostrou dependência com a concentração de óleo nos sistemas estudados. As isotermas de adsorção (a 30°C) dos pós obtidos ajustaram-se melhor ao modelo GAB e os teores de umidade da monocamanda (xm) para este modelo ficaram entre 2, 5 % e 5,1% para as micropartículas de CPSL e GA e entre 5,1% e 6,1% para as micropartículas de IPS e GA

En Nouvelle-Calédonie il y a une forte volonté politique pour diversifier l'aquaculture qui repose encore aujourd'hui sur la crevetticulture. Dans ce contexte le crabe de palétuvier est considéré comme une espèce à fort potentiel. Un des principaux verrous au développement de la carcinoculture en Nouvelle-Calédonie est la disponibilité d'un aliment granulé commercial. Ainsi le principal objectif de cette thèse est d'améliorer notre connaissance des besoins nutritionnels du crabe de palétuvier afin d'être en mesure de formuler un aliment équilibré pour son élevage. Cependant avant d'aborder les études nutritionnelles nous avons vérifié le nombre d'espèces de crabes de palétuvier présentes en Nouvelle-Calédonie.Nos résultats d'études morphologiques et génétiques de 63 individus provenant de 9 sites des côtes Ouest et Nord-Est de la Nouvelle-Calédonie ont confirmé l'existence d'une unique espèce commercialisée: Scylla serrata. C'est donc sur cette espèce que nous avons travaillé en nutrition avec deux séries expérimentales ayant pour objectifs: i) d'évaluer le concentré protéique de soja (CPS) en comparaison avec la farine de poisson comme principale source en protéines et ii) de déterminer le taux optimum d'incorporation du CPS pour la mue et la croissance tissulaire des animaux. Nous avons ainsi observé deux phases de croissance tissulaire au cours d'un cycle de mue (CM): une phase rapide (CTR) qui démarre après la mue et dure jusqu'au début de l'intermue (elle représente 30% du CM) suivi d'une phase de croissance lente (CTL) sur toute la durée de l'intermue et jusqu'à la mue suivante (elle représente 70% du CM). L'accumulation des protéines et des lipides au cours du CM a suivi le même profil de croissance tissulaire contrairement aux cendres qui ont augmenté de façon rapide durant 5 jours suivant l'ecdysis pour atteindre un plateau jusqu'à la prochaine mue. Les deux phases de croissance étaient corrélées avec une prise de l'aliment par les animaux maximale pendant les deux premières semaines suivant la mue. Elle a diminué de moitié sur les 5 semaines suivantes et s'est maintenue ensuite à un niveau de base jusqu'à la prochaine mue. L'énergie ingérée était allouée principalement à la croissance et à l'entretient respectivement durant les périodes CTR et CTL. Durant la phase de croissance lente, 28% de l'énergie ingérée étaient mise en réserve en prévision de la prochaine mue. Le remplacement de la farine de poisson par la CPS n'a pas modifié la croissance tissulaire,l'efficience de l'aliment et le bilan énergétique des animaux quelque soit la phase de croissance considérée. Le taux d'incorporation dans l'aliment de 42% de CPS a permis la meilleure croissance (fréquence de mue et croissance tissulaire, efficience de l'aliment et la rétention de l'énergie des protéines et des lipides. L'hypothèse d'une toxicité de l'ammonium issu de la dégradation des protéines en excès ou des facteurs antinutritionnels du soja est avancée pour expliquer les effets négatifs observés avec les aliments renfermant des taux d'incorporation élevés en CPS. En conclusion, nos travaux apportent des informations originales sur la croissance tissulaire et les dépenses énergétiques durant un cycle de mue et la capacité du crabe juvénile d'utiliser le CPS comme principale source de protéines. Sur ces bases nous somme en mesure de préconiser des contraintes nutritionnelles permettant de formuler un aliment équilibré sans farine de poissons pour l'élevage du crabe de palétuvier S.serrata. / In New Caledonia, there is the strong political will to diversify aquaculture which is mainly based on shrimp farming. In this context, mud crabs have been considered as a potential species for aquaculture development. One of the main constraints to develop crab farming is the availability of formulated feed. Thus, the main purpose of this thesis is to get information on the crab nutritional requirements in order to formulate a balanced diet. However, we had to clarify first how many species of mud crab were present in New-Caledonia. The result of our morphological and genetic investigations carried out on 63 specimens from 9 areas of the west and northeast coast of New-Caledonia confirmed that only one species, Scylla serrata, is commercialized in this country. Consequently, S. serrata was used in our nutritional study based on two experiments to: i) evaluate the soy protein concentrate (SPC) compared with the fishmeal as the main protein source and ii) determine the optimum level of SPC in the diet for molting and tissue growth. We observed two tissue growth phases within one molt cycle (MC): a fast tissue growth (FTG) occurred after ecdysis until early intermolt stage (30% of MC) which is followed by a slow tissue growth (STG) period from intermolt to ecdysis (70% of MC). Protein and lipid deposition followed the same trend than tissue growth while ash level increased quickly during five days after molt and then remained stable until the next molt. The two growth phases were correlated with the voluntary feed intakes (VFI) which was maximum during 2 weeks after ecdysis and then decreased by 50% over the five following weeks to reach a baseline until the next molt. Intake energy was allocated mainly for growth during FTG period and for maintenance during STG period. During STG, 28% of the ingested energy was accumulated for the next ecdysis. Replacement of fishmeal by SPC as main protein source did not affect tissue growth, efficiency of feed utilization and energy budget of crabs whatever the tissue growth period considered. The dietary SPC inclusion of 42% in the diet promoted growth (molt frequency and tissue growth), feed efficiency and retention of energy, protein and lipid. Hypothesis related to ammonia toxicity from catabolism of proteins in excess or anti-nutritional factors from soybean could explain the negative effects of higher inclusion of SPC in the diet for juvenile crabs. In conclusion, our work brings novel information on tissue growth, energy budget during a molt cycle and the ability of juvenile crab to use SPC as a main source of protein. On this basis we suggest to formulate nutritionally balanced diet without fishmeal to farm juvenile mud crabs S. serrata.

Soy flour (SF), a by-product of the soybean oil extraction processing, was investigated for its application in soy-polypropylene composites for interior automotive applications. The emphasis of this work was the understanding of this new type of filler material and the contribution of its major constituents to its thermal stability and impact properties. For this reason, reference materials were selected to represent the protein (soy protein isolate (SPI)) and carbohydrate (soy hulls (SH)) constituents of the soy flour. Additional materials were also investigated: the residue obtained after the protein removal from the soy flour which was called insoluble soy (IS), and the remaining liquid solution after acid precipitation of the proteins, containing mostly sugars and minerals, which was called soluble sugar extract (SSE). Two treatments, potassium permanganate and autoclave, were analyzed for their potential to modify the properties of the soy composite materials. An acid treatment with sulfuric acid conducted on soy flour was also considered. The soy materials were studied by thermogravimetric analysis (TGA) under isothermal (in air) and dynamic (in nitrogen) conditions. SPI had the highest thermal stability and SSE the lowest thermal stability for the early stage of the heating process. Those two materials had the highest amount of residual mass at the end of the dynamic TGA in nitrogen. The two treatments showed minimal effect on the isothermal thermal stability of the soy materials at 200 ??C. A minor improvement was observed for the autoclave treated soy materials. Fourier transformed infrared (FTIR) spectroscopy indicated that the chemical surface composition differed according to type of the soy materials but no difference could be observed for the treatments within one type of soy material. Contact angle analysis and surface energy estimation indicated differences of the surface hydrophobicity of the soy materials according to type of material and treatment. The initial water contact angle ranged from 57 ?? for SF to 85 ?? for SH. The rate of water absorption increased dramatically after the autoclave treatment for IS and SPI. Both materials showed the highest increase in the polar surface energy fraction. In general, the major change of the surface energy was associated with change of the polar fraction. After KMnO4 treatment, the polar surface energy of SF, IS and SPI decreased while SH showed a slight increase after KMnO4 treatment. A relationship between protein content and polar surface energy was observed and seen to be more pronounced when high protein containing soy materials were treated with KMnO4 and autoclave. Based on the polar surface energy results, the most suitable soy materials for polypropylene compounding are SPI (KMnO4), SH, and IS (KMnO4) because their polar surface energy are the lowest which should make them more compatible with non-polar polymers such as polypropylene. The soy materials were compounded as 30 wt-% material loading with an injection moulding grade polypropylene blend for different combinations of soy material treatment and coupling agents. Notched Izod impact and flexural strength as well as flexural modulus estimates indicated that the mechanical properties of the autoclaved SF decreased when compared to untreated soy flour while the potassium permanganate treated SF improved in impact and flexural properties. Combinations of the two treatments and two selected (maleic anhydride grafted polypropylene) coupling agents showed improved impact and flexural properties for the autoclaved soy flour but decreased properties for the potassium permanganate treated soy flour. Scanning electron microscopy of the fractured section, obtained after impact testing of the composite material, revealed different crack propagation mechanisms for the treated SF. Autoclaved SF had a poor interface with large gaps between the material and the polypropylene matrix. After the addition of a maleic anhydride coupling agent to the autoclaved SF and polypropylene formulation, the SF was fully embedded in the polymer matrix. Potassium permanganate treated SF showed partial bonding between the material and the polymer matrix but some of the material showed poor bonding to the matrix. The acid treated SF showed cracks through the dispersed phase and completely broken components that did not bind to the polypropylene matrix. In conclusion, the two most promising soy materials in terms of impact and flexural properties improvement of soy polypropylene composites were potassium permanganate treated SF and the autoclaved SF combined with maleic anhydride coupling agent formulation.

Tesis por compendio / [EN] Persimmon (Diospyros kaki L.) 'Rojo Brillante' is an astringent variety characterised by good growing conditions, excellent colour, size, sensory characteristics and good nutritional properties. In the last decade, its production has grown substantially in Spain given the application of high levels of CO2 to remove astringency while firmness is preserved. This technology has also increased its potential as a fresh-cut commodity. However, physical damage during processing result in degradation of the colour and firmness of the product and a higher susceptibility to microbial spoilage that significantly reduces the fruit's shelf life. The objective of the present thesis was to develop optimum procedures for processing and marketing 'Rojo Brillante' persimmon into a fresh-cut product with the maximum shelf life and best physicochemical, nutritional, sensory and microbiological quality. Firstly, the objective was to evaluate the effect of the maturity stage (MS) at harvest, storage time at 15 ºC before processing, and the application of different antioxidant treatments on enzymatic browning, sensory and nutritional quality of fresh-cut 'Rojo Brillante' persimmon during storage at 5 ºC. Concentrations of 10 g L-1 ascorbic acid (AA) or 10 g L-1 citric acid (CA) controlled tissue browning and maintained the visual quality of fresh-cut persimmon above the limit of marketability for 6-8 storage days at 5 ºC, depending on the MS. However, these acidic solutions reduced fruit firmness as compared to control samples. Further studies showed that the combination of these antioxidants with 10 g L-1 CaCl2 maintained firmness of the persimmon slices within the same range as the control samples. In another work, the application of 1-methylcyclopropene (1-MCP) allowed to process fruits after 45 days of storage at 1 ºC with commercial firmness and the antioxidant solution (10 g L-1 CA + 10 g L-1 CaCl2) extended the limit of marketability up to 9 days of storage at 5 ºC. Different controlled atmosphere conditions in combination with AA or CA dips were also evaluated as a first step to select optimum O2 and CO2 concentrations for modified atmosphere packaging (MAP) of fresh-cut 'Rojo Brillante' persimmons. Overall, the combination of antioxidant dips and a controlled atmosphere composed of 5 kPa O2 (balance N2) was proved to be the most effective combination to control enzymatic browning. This atmosphere maintained the visual quality of persimmon slices within the limit of marketability during 7- 9 days at 5 ºC. On the contrary, high CO2 concentrations (10 or 20 kPa) induced darkening in some tissue areas, associated with a flesh disorder known as 'internal flesh browning'. Later studies confirmed the beneficial effect of an active MAP in 5 kPa O2 compared to passive MAP to improve the visual quality of fresh-cut 'Rojo Brillante' persimmon, showing a synergic effect with the antioxidant dip (10 g L-1 CA + 10 g L-1 CaCl2). Antioxidant edible coatings were prepared from whey protein isolate (WPI), soy protein isolate (SPI), hydroxylpropyl methylcellulose (HPMC) and apple pectin as the polymeric matrix. All edible coatings were amended with the antioxidant combination selected (10 g L-1 CA + 10 g L-1 CaCl2). All the edible coatings tested proved effective to control enzymatic browning of persimmon slices. However, the samples treated with the HPMC- and pectin- based coatings were scored with a better visual quality that the rest of the treatments. In general, free radical scavenging activity and total carotenoid content increased in late-season persimmons; whereas, processing (cutting and storage at 5 ºC), antioxidant dips, controlled atmosphere storage or edible coatings had no clear effect on nutritional quality (vitamin C, free radical scavenging activity, total phenolic content, and carotenoids) of fresh-cut persimmons. / [ES] El caqui persimmon (Diospyros kaki L.) 'Rojo Brillante' es un cultivar astringente que presenta unas propiedades organolépticas y nutricionales excelentes. En la última década, su cultivo en el área mediterránea de España se ha incrementado de manera exponencial con el desarrollo de la tecnología que permite eliminar la astringencia, manteniendo la firmeza del mismo. Esta nueva forma de presentación, aporta numerosas ventajas, entre la que se incluye la posibilidad de ser comercializado como fruta fresca cortada. Sin embargo, el éxito comercial del producto está limitado por el pardeamiento enzimático, la pérdida de firmeza y al crecimiento microbiano. En este contexto, el objetivo de la Tesis ha sido el desarrollo de caqui 'Rojo Brillante' fresco cortado mediante un enfoque que integra el estudio de las características del producto en el momento del procesado y de distintas tecnologías que mantengan la calidad físico-química, sensorial, nutricional y microbiológica del producto durante un periodo que permita su comercialización. En primer lugar, se evaluó el efecto del estado de madurez (MS) en el momento de recolección, el tiempo de almacenamiento a 15 ºC antes del procesado y la aplicación de diferentes antioxidantes en el pardeamiento enzimático y la calidad sensorial y nutricional del caqui 'Rojo Brillante' cortado y almacenado a 5 ºC. La aplicación de 10 g L-1 de ácido ascórbico (AA) ó 10 g L-1 ácido cítrico (CA) controló el pardeamiento enzimático y mantuvo la calidad visual del caqui por encima del límite de comercialización entre 6 y 8 días de almacenamiento a 5 ºC, dependiendo del MS. Sin embrago, la aplicación de estos antioxidantes redujo de manera significativa la firmeza del fruto respecto al control. La combinación de estos antioxidantes con 10 g L-1 de CaCl2 permitió mantener la firmeza en el mismo rango que las muestras control. En un trabajo posterior, la aplicación de 1-metilciclopropeno (1-MCP) permitió procesar caqui almacenado 45 días a 1 ºC con una buena firmeza comercial y el tratamiento antioxidante (10 g L-1 CA + 10 g L-1 CaCl2) consiguió alcanzar un límite de comercialización del producto de 9 días a 5 ºC. La evaluación de distintas atmósferas controladas en combinación con tratamientos antioxidantes (AA o CA), como paso previo al envasado en atmósfera modificada (MAP) del caqui, mostró como más efectiva en el control del pardeamiento enzimático la atmósfera compuesta por 5 kPa O2 (balance N2). Esta atmósfera mantuvo la calidad visual del caqui cortado dentro del límite de comercialización durante 7-9 días a 5 ºC. Por el contrario, la aplicación de altas concentraciones de CO2 (10 ó 20 kPa) dio lugar a un pardeamiento en ciertas zonas de la pulpa que se conoce como 'internal flesh browning'. Estudios posteriores confirmaron el efecto beneficioso del envasado de caqui cortado y tratado con solución antioxidante (CA-CaCl2) en una MAP activa de 5 kPa O2 en la calidad visual del fruto frente a la aplicación de una MAP pasiva. El desarrollo de recubrimientos comestibles con capacidad antioxidante se realizó mediante la incorporación de antioxidantes (10 g L-1 CA + 10 g L-1 CaCl2) a formulaciones a base de proteína de suero lácteo (WPI), proteína de soja (SPI), hidroxipropilmetilcelulosa (HPMC) y pectina. Todos los recubrimientos fueron efectivos controlando el pardeamiento enzimático del caqui cortado, siendo las muestras recubiertas con HPMC y pectina las mejor evaluadas visualmente. En general, el procesado, la aplicación de antioxidantes, el envasado en atmósferas controladas y los distintos recubrimientos comestibles estudiados, si bien no mostraron un efecto claro en los parámetros de calidad nutricional evaluados, no tuvieron un efecto negativo en los mismos. Por otra parte, los frutos cosechados a final de campaña tuvieron mayor actividad antioxidante y contenido en carotenoides. / [CA] El caqui persimmon (Diospyros kaki L.) 'Rojo Brillante' és un cultiu astringent que presenta unes propietats organolèptiques i nutricionals excel¿lents. En la última dècada, el seu cultiu en l'àrea mediterrània d'Espanya s'ha incrementat de manera exponencial amb el desenvolupament de la tecnologia que permet eliminar l'astringència, mantenint la fermesa del mateix. Esta nova forma de presentació, aporta un gran nombre d'avantatges, entre els quals s'inclou la possibilitat de comercialitzar-lo com fruita fresca processada. No obstant, l'èxit comercial del producte està limitat per pardetjament enzimàtic, la pèrdua de fermesa i el creixement microbià. L'objectiu de la Tesis ha estat en el desenvolupament de caqui 'Rojo Brillante' tallat en fresc mitjançant un enfocament que integra l'estudi de les característiques del producte en el moment del processat i de diferents tecnologies en el manteniment de la qualitat físico-química, sensorial, nutricional i microbiològica del producte durant un període que permeta la seua comercialització. En primer lloc, es va avaluar l'efecte de l'estat de maduresa (MS) en el moment de recol¿lecció, el temps d'emmagatzemament a 15ºC abans del processat i l'aplicació de diferents tractaments antioxidants en el pardetjament enzimàtic i la qualitat sensorial i nutricional del caqui 'Rojo Brillante' tallat i emmagatzemat a 5 ºC. L'aplicació de 10 g L-1 d'àcid ascòrbic (AA) o 10 g L-1 d'àcid cítric (CA) va controlar el pardetjament enzimàtic i va mantenir la qualitat visual del caqui per damunt del límit de comercialització entre 6-8 dies d'emmagatzemament a 5 ºC, depenent del MS. No obstant, l'aplicació d'antioxidants va reduir de manera significativa la fermesa del fruit comparat amb el control. La combinació d'aquestos antioxidants amb 10 g L-1 de CaCl2 va permetre mantenir la fermesa en el mateix rang que les mostres control. En un treball posterior, l'aplicació de 1-metilciclopropeno (1-MCP) va permetre processar caqui emmagatzemat 45 dies a 1 ºC amb una bona fermesa comercial i a més, el tractament antioxidant (10 g L-1 CA + 10 g L-1 CaCl2) va aconseguir un límit de comercialització del producte tallat de 9 dies a 5 ºC. L'avaluació de diferents atmosferes controlades en combinació amb tractaments antioxidants (AA o CA), com a pas previ a l'envasament en atmosfera modificada (MAP) del caqui 'Rojo Brillante, va mostrar com a més efectiva en el control del pardetjament enzimàtic l'atmosfera composta per 5 kPa O2 (balanç N2). Aquesta atmosfera va mantenir la qualitat visual del caqui tallat dins del límit de comercialització durant 7-9 dies a 5 ºC. Per contra, l'aplicació d'altes concentracions de CO2 (10 ó 20 kPa) va donar lloc a un pardetjament en certes zones de la polpa, el qual és conegut com 'internal flesh browning'. Estudis posteriors van confirmar l'efecte beneficiós de l'envasament de caqui tallat i tractat amb solució antioxidant (CA-CaCl2) en una MAP activa de 5 kPa O2 millorant la qualitat visual de la fruita front a l'aplicació de una MAP passiva. El desenvolupament de recobriments comestibles amb capacitat antioxidant es va realitzar mitjançant la incorporació d'antioxidants (CA-CaCl2) en formulacions a base de proteïna de sèrum làctic (WPI), proteïna de soia (SPI), hidroxipropilmetilcel-lulosa (HPMC) i pectina. Tots els recobriments van ser efectius controlant el pardetjament enzimàtic del caqui tallat. No obstant, les mostres recobertes amb HPMC i pectina van ser millor avaluades visualment que la resta de tractaments. En general, el processat, l'aplicació d'antioxidants, l'envasament en atmosferes controlades i els distints recobriments comestibles estudiats, si bé no van mostrar un efecte clar en els paràmetres de la qualitat nutricional avaluats, no van tindre un efecte negatiu en els mateixos. Per altra banda, els fruits recol¿lectats a final de temporada van tenir major activitat antioxidant i contingut en / Sanchís Soler, E. (2016). Effect of processing on the physicochemical, sensory, nutritional and microbiological quality of fresh-cut 'Rojo Brillante' persimmon [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/62588 / Compendio