The demand for clean and environmentally benign energy resources has been a great concern in the last two decades. To alleviate the associated environmental problems, reduction of the use of fossil fuels by developing more cost-effective renewable energy technologies becomes more and more significant. Among various types of renewable energy sources, solar energy and bioenergy take a great proportion. This dissertation focuses on the heat transfer and flow in solar energy and bioenergy systems, specifically for Thermal Energy Storage (TES) systems in Concentrated Solar Power (CSP) plants and open-channel algal culture raceways for biofuel production. The first part of this dissertation is the discussion about mathematical modeling, numerical simulation and experimental investigation of solar TES system. First of all, in order to accurately and efficiently simulate the conjugate heat transfer between Heat Transfer Fluid (HTF) and filler material in four different solid-fluid TES configurations, formulas of an effective heat transfer coefficient were theoretically developed and presented by extending the validity of Lumped Capacitance Method (LCM) to large Biot number, as well as verifications/validations to this simplified model. Secondly, to provide design guidelines for TES system in CSP plant using Phase Change Materials (PCM), a general storage tank volume sizing strategy and an energy storage startup strategy were proposed using the enthalpy-based 1D transient model. Then experimental investigations were conducted to explore a novel thermal storage material. The thermal storage performances were also compared between this novel storage material and concrete at a temperature range from 400 °C to 500 °C. It is recommended to apply this novel thermal storage material to replace concrete at high operating temperatures in sensible heat TES systems. The second part of this dissertation mainly focuses on the numerical and experimental study of an open-channel algae culture raceway for biofuel production. According to the proposed flow field design of ARID-HV algal raceway, experiments and numerical simulation have been conducted to understand the enhancement of flow mixing in the flow field of ARID-HV raceway by cutting slots on top of the dam near the dead zones. A new method was proposed to quantitatively evaluate the flow mixing by using the statistics of temporal and spatial distribution of the massless fluid particles (centered in each cell at the inlet surface) in the raceway collecting the data of path-lines of fluid particles from CFD results. It is hoped that this method can be applied to assist the algal raceway flow field design as well as other engineering applications. The third part introduces the details about the construction work of a high temperature molten salt test loop. Because of the limited operating temperature of conventional synthetic oils, in order to obtain higher energy conversion efficiency, higher operating temperature is always desirable in a CSP plant which leads to the requirement of new generation of HTF. Currently, a halide salt eutectic mixture (NaCl-KCl-ZnCl₂) as a potential HTF for future CSP applications has been proposed by a multi-institute research team, led by University of Arizona. The thermophysical properties of the halide eutectic salt have been measured. However, this new developed halide eutectic salt has not been tested in a circulating loop at a high operating temperature for the measurement of heat transfer coefficient. It is a significant effort to build such a test system due to extremely high operating temperature. As a consequence, in the third part of this dissertation, details about the design of the lab-scale test system and all the equipment items will be introduced. The investigations included in this dissertation for the heat transfer and flow in solar energy and bioenergy systems are of particular interest to the renewable energy engineering community. It is expected that the proposed methods can provide useful information for engineers and researchers.

This thesis investigates the possibility of using an unglazed flat-plate solar collector as a cooling radiator. The solar collector will be connected to the condenser of a heat pump and used as cooler during nighttime. Daytime the solar collector will be connected to the evaporator of the heat pump and used as heat source. The two widely differing fields of application make special demands on the solar collector. The task is given by the heat pump manufacturer Thermia and the main objective is to find out whether a solar collector should be used as a cooler or not. The performance of the solar collector under varying environmental conditions is investigated using COMSOL Multiphysics 3.3. Only the cooling properties are investigated here. The performance of the solar collector as a heat exchanger is estimated using the effectiveness-NTU method, and the solar collector is found to be a good heat exchanger at low wind speeds. The heat transfer coefficients of the convection and radiation are determined for varying temperature and wind speeds. The convective heat transfer coefficient is lowered by tubes above the absorber plate and for a high convective heat transfer rate the solar collector surface should be smooth. For a high radiative heat transfer rate the surface needs to have a high emissivity. The cooling rate is higher from a warm surface than from a cold and since no temperature change of the heat carrier is necessary the solar collector should be kept at a high temperature. To increase the cooling rate alterations need to be made to the solar collector that makes its heating performance deteriorate. A solar collector that can be used for cooling is not an efficient solar collector.

Satellite District Heating and Cooling (DHC) systems offer an alternative structure to conventional, centralized DHC networks. Both use a piping network carrying steam or water to connect disparate building heating and cooling loads together, providing a platform for improving energy efficiency, reducing emissions, and incorporating alternative means of energy generation. However, satellite DHC networks incorporate thermal production units that are distributed amongst the buildings nodes, which offers greater operational flexibility and reduced capital cost savings for applications using existing building stock. This study was focused on the development of the methodology behind a comprehensive energy model that can assess the practical and financial viability of satellite DHC network scenarios. A detailed scenario application of the model demonstrated significant energy savings and investment potential. Additionally, environmental assessment methods and alternative generation technology were explored in supplementary studies of Deep Lake Water Cooling (DLWC) and building-scale Combined Heat and Power (CHP).

Satellite District Heating and Cooling (DHC) systems offer an alternative structure to conventional, centralized DHC networks. Both use a piping network carrying steam or water to connect disparate building heating and cooling loads together, providing a platform for improving energy efficiency, reducing emissions, and incorporating alternative means of energy generation. However, satellite DHC networks incorporate thermal production units that are distributed amongst the buildings nodes, which offers greater operational flexibility and reduced capital cost savings for applications using existing building stock. This study was focused on the development of the methodology behind a comprehensive energy model that can assess the practical and financial viability of satellite DHC network scenarios. A detailed scenario application of the model demonstrated significant energy savings and investment potential. Additionally, environmental assessment methods and alternative generation technology were explored in supplementary studies of Deep Lake Water Cooling (DLWC) and building-scale Combined Heat and Power (CHP).

This thesis presents and demonstrates procedures to model and optimize the collector field of a parabolic trough solar thermal power plant. The collector field of such a plant is universally organized into parallel loops of solar collectors. Heat transfer fluid returning from the energy conversion plant is heated to a moderately high temperature in the field. Typically fluid enters a collector loop around 270 °C and leaves at 380 °C. The fluid is then returned to the plant to generate steam. In the first part of this thesis, the collector field and the energy conversion system of a typical parabolic trough solar thermal power plant are modeled. The model is compared with actual performance data and is enhanced and verified as necessary. Originally, the collectors in the plants under consideration were provided with evacuated tube receivers of the highest feasible efficiency without much regard for cost effectiveness. In practice, these receivers have failed at an unexpected rate and need replacement. It is unlikely that a very expensive evacuated tube receiver is now the most cost effective for every location in a collector loop. In particular, a receiver optimized for 270 °C operation may not be optimal at 380 °C. For example, a relatively inexpensive receiver with a flat black absorber and no vacuum may be more cost effective in the lower temperature segments of a loop. In the second part of this thesis, a procedure for the optimum deployment of collectors is developed and demonstrated. The results of this research should be directly applicable to the refurbishment and upgrading of several of the largest solar energy plants in the world.

Η ηλιακή ενέργεια μπορεί να συμβάλει στην αντιμετώπιση του ενεργειακού προβλήματος, με την ευρεία αξιοποίηση των φωτοβολταϊκών και των θερμικών ηλιακών συλλεκτών. Τα φωτοβολταϊκά συστήματα που συνδυάζονται με θερμικές μονάδες κυκλοφορίας νερού ή αέρα, για την απολαβή της θερμότητας από αυτά και την ικανοποιητική διατήρηση της απόδοσής των, αποτελούν τα υβριδικά φωτοβολταϊκά/θερμικά συστήματα (φβ/θ). Τα συστήματα αυτά παράγουν ηλεκτρική και θερμική ενέργεια ταυτόχρονα, αυξάνοντας την ολική παραγόμενη ενέργεια. Με τη χρήση ορισμένων διατάξεων βελτίωσης της απολαβής της θερμότητας από τα φωτοβολταϊκά και της αύξησης της αποδιδόμενης ενέργειας των φωτοβολταϊκών και των θερμικών ηλιακών συλλεκτών, είναι δυνατή η βελτίωση της αποδοτικότητας των συσκευών αυτών, για μια πιο αποτελεσματική εφαρμογή τους στα κτήρια. Η διπλωματική εργασία που ακολουθεί περιλαμβάνει τη μελέτη φωτοβολταϊκών, υβριδικών φωτοβολταϊκών και θερμικών ηλιακών συσκευών. Πραγματοποιήθηκε μελέτη υβριδικού φωτοβολταϊκού/θερμικού συστήματος αέρα με διάφορες βελτιώσεις της αποδοτικής λειτουργίας του και με την προσθήκη μεταλλικών φύλλων ή σωλήνων ροής νερού στον αεραγωγό. Ακόμη, μελετήθηκε επίπεδος ηλιακός θερμικός συλλέκτης με προσθήκη διάφορων τύπων ανακλαστήρων (λευκή επιφάνεια, γαλβανιζέ μεταλλικό φύλλο και καθρέφτης). Πραγματοποιήθηκαν επίσης πειράματα με σωλήνα κενού, ο οποίος συνδυάστηκε με ανακλαστήρες για την αύξηση της προσλαμβανόμενης ηλιακής ακτινοβολίας και βελτίωση της αποδιδόμενης θερμότητας. Με βάση τα αποτελέσματα παρατίθενται συμπεράσματα και προτάσεις σχετικά με τις σύνθετες διατάξεις που αναφέρθηκαν. / Solar energy systems can contribute to energy demand by the proper synergy of photovoltaics and solar thermal collectors. The PV modules which are combined with thermal units and circulating water or air to extract the heat from them, constitute the hybrid photovoltaic/thermal systems (PV/T). These systems provide electrical and thermal energy simultaneously, increasing the total energy output. Adapting some effective heat extraction elements to PV modules and applying devices to have solar radiation increase by the absorbing surfaces of PV and of thermal collectors, an improvement of operation and performance of these systems can be achieved regarding their application to buildings. The thesis that follows includes a study of photovoltaics, hybrid photovoltaic/ thermal systems and solar thermal collectors. More specifically, a study of an air heating hybrid photovoltaic/thermal system was performed, improving suitably the heat extraction by inserting corrugated metallic sheets or water pipes, inside the air channel that is attached to rear surface of PV modules. In addition, a solar thermal collector was studied, by applying several types of reflectors (white plate reflector, galvanized iron plate reflector and specular reflector). Furthermore, a vacuum tube type collector was tested, combined also with reflectors to increase input solar radiation and increase thermal performance. Finally, conclusions and suggestions for a further study, on the above mentioned solar energy systems is included, based on the reported experimental results.

[pt] Um sistema térmico de armazenamento da energia com pasta de cristais de gelo foi desenvolvido para aplicações de condicionamento de ar e resfriamento de processos. O sistema usa um evaporador orbital de haste, um trocador de calor vertical do tipo tubo e carcaça com intensificação mecânica de transferência de calor. A pasta de gelo é produzida continuamente sem acumulação no evaporador e é compatível com unidades condensadoras convencionais, tanques de armazenamento e bombas. Soluções aquosas diluídas ou soluções inorgânicas de salmoura promovem a formação de cristais de gelo, e o gelo líquido resultante pode ser bombeado ou por gravidade alimentar um tanque de armazenamento. O circuito hidráulico de refrigeração (carga térmica) pode ser desacoplado da produção do gelo utilizando-se o tanque de armazenamento. O armazenamento de gelo líquido fornece temperaturas consistentemente baixas à medida que se derrete o gelo, que por sua forma pode ser derretido também muito rapidamente. Com suas altas temperaturas características de evaporação e elevados fluxos do calor, os sistemas de geração de gelo líquido apresentam potencial para reduzir significativamente os custos de capital inicial e operação, quando comparados com tecnologias de sistemas estáticos de gelo ou ice harvesting. / [en] New ice crystal slurry thermal energy storage (TES) system has been developed for both HVAC and process cooling applications. The system uses an orbital rod evaporator (ORE), a vertical shell-and-tube heat exchanger with mechanical heat transfer augmentation, as a dynamic ice maker to generate liquid ice. Ice forms continuously without accumulation in the ORE and is compatible with conventional condensing units, storage tanks, and pumps. Dilute glycol or inorganic brine solutions promote formation of ice crystals, and the resulting liquid ice may be pumped or gravity fed to a storage tank. The cooling load circuit can be hydraulically decoupled from ice production at the storage tank. Stored liquid ice provides consistently low solution supply temperatures over significant portions of the ice melt period and may be melted very rapidly. With its characteristic high evaporator temperatures and high heat fluxes, ORE TES systems have the potential for significantly lower capital and operating costs than static ice or ice harvesting technologies.

A promising and novel solar concentrator design has been thoroughly investigated and optimised. A prototype concentrator based on this novel geometry was validated using ray tracing techniques. This ray tracing demonstrated the comparative performance of this novel concentrator in regards to equivalent parabolic dishes. The effect of mirror surface normal errors on performance was established using Monte-Carlo based ray tracing code, which agreed well with the optical performance of this prototype which was determined experimentally. A need for low-cost solar cookers to replace bio-mass worldwide was identified, and the concentrator design was then developed as a low-cost solar oven. Despite existing in some number, no current design is able to achieve high performance at low-cost. An industrial partner, Dytecna, was initially involved in the process of this development of the system as a solar cooker. In support of a field trial for the solar cooker developed with Dytecna, a detailed thermal model of the oven was developed. A low-cost lightmeter was constructed and calibrated in order to measure the direct normal irradiance during the field trial in Italy. Laboratory work provided baseline results for the heating of various thermal masses in the oven. The Italian field trials provided a wealth of feedback into the design of the system and many valuable results. The solar cooker was able to bring 0.75L of water to the boil in 33 minutes with an average heat throughput of 203W. Important benchmark results and practical experience of several competing receiver materials was obtained; further lab testing provided more accurate measurements of the receivers' performances. The experiences of the Italian field trial were fed back into the design of a subsequent prototype, intended for a much larger field trial in Tanzania. Improvements in the hotplate, receiver material, and the oven were all incorporated into the design. Additionally, the structure of the solar cooker was redesigned to incorporate a low-cost wooden construction. Supporting work was conducted for the month long trial in which 8 solar cookers would be distributed to families in Tanzania. The field trial in Tanzania provided a wealth of user feedback into the design. At the same time the new solar cooker exceeded previously established performances in Italy. The new design was able to provide an average of 246W of heat to 1kg of water, which was brought to boiling point in 25 minutes. This represents a heating efficiency of 66% compared to the incident solar flux on the hotplate. In response to findings during the Tanzanian trials, further laboratory work was conducted into establishing the reflectivities of low-cost candidate mirror materials. Throughout all phases of the project the design of the solar cooker was refined and improved with the goal of a solar cooker design that could reach price-point, performance, and usability standards which would ensure market success.

Ce travail traite la modélisation et l'optimisation des centrales solaires thermodynamiques à concentration produisant de l'électricité pour l'électrification des zones rurales isolées et mal raccordées au réseau électrique. D’abord, un modèle optique et thermique détaillé des concentrateurs solaires cylindro-paraboliques est présenté permettant l'identification de capteurs existants et la création de corrélations qui peuvent être injectées dans un modèle plus global. Dans un second temps, un modèle original d'un stock de chaleur stratifié de type « lit de roche » est développé. Le nouveau modèle proposé permet de déterminer analytiquement le profil de température dans le stock à n'importe quel instant dans le cas d'une température d'entrée régulée. Ensuite, deux alternatives de bloc moteur sont modélisées : le moteur Stirling et le Cycle Organique de Rankine (ORC acronyme anglais pour Organic Rankine Cycle). Concernant le moteur Stirling, une revue critique des modèles existants a été effectuée. Certains de ces modèles ont été implémentés et complétés par des modèles originaux des pertes par fuite de matière et par effet navette. Le cycle organique de Rankine, lui, est modélisé par un modèle orientée vers l'optimisation. Enfin, une optimisation mono et multicritère d’une centrale solaire est effectuée. La configuration étudiée est équipée d’un stock de chaleur et d’une chaudière d’appoint. Elle est optimisée selon trois critères : le coût moyen actualisé de l'électricité (LCOE acronyme anglais pour Levelized Cost Of Electricity), le rendement énergétique de la centrale et la quantité de CO2 émise par Kilowatt heure d'électricité produite / This work deals with the modelling and the optimization of thermodynamic solar power plants intended to supply electricity to isolated locations. Firstly, a state of the art of solar collectors is achieved and a model for parabolic trough collectors is proposed. This model is used for actual collectors identification. It is used also to propose correlations to be introduced in the whole system model. In a second time, a state of the art of energy storage technologies is conducted and an original model of a packed bed storage tank is proposed. This model gives an explicit solution of the temperature inside the tank without using a time step based numerical resolution. Two alternatives for the power block are given: Stirling engines and Organic Rankine Cycles. For Stirling engines, a critical review of existing models is performed. Some losses occurring in Stirling engines are not well documented in the literature as leakage losses at the power piston and displacer gap losses. Therefore, original models are proposed to estimate these losses. When compared to former models in the literature, the new model of the displacer gap losses demonstrates clearly that it is very important to use decoupled models with caution. Concerning the ORC, an optimization-oriented model is proposed. Finally, a mono and multi-objective optimization of a solar power plant is performed. The optimized system is composed of a solar field, a packed bed heat storage, a power block and an auxiliary fired heater. Objective functions used in this study are: the Levelized Cost of Electricity (LCOE), the energetic efficiency of the power plant and CO2 emission per kilowatt hour of electricity

Distributed power generation through renewable sources of energy has the potential of meeting the challenge of providing electricity access to the off-grid population, estimated to be around 1.2 billion residing across the globe with 300 million in India, in a sustainable way. Technological solutions developed around these energy challenges often involve thermal systems that convert heat available from sources like solar, biomass, geothermal or unused industrial processes into electricity. Conventional steam based thermodynamic cycle at distributed scale (< 1 MWe) suffers from low efficiency driving scientific research to develop new, scalable, efficient and economically viable power cycles. This PhD work conducts one such study which provides a database of thermal power blocks optimized for the lowest initial investment cost to developers of distributed power plants. The work is divided in two steps; a) feasibility study of various thermodynamic cycles for distributed power generation covering different operating temperature regimes and b) perform their detailed thermo-economic modelling for the heat sources mentioned above. Thermodynamic cycles are classified into three temperature domains namely, low (< 450 K), medium (< 600 K) and high (< 1000 K) T cycles. Any fluid whose triple point temperature is below the typical ambient temperatures is a potential working fluid in the power cycle. Most of the organic and the inorganic fluids satisfy this criterion and can be perceived as potential power cycle fluids. The general notion is that organic fluids are more suited for low or medium temperature cycles whereas inorganic fluids for high temperature ones. Organic fluids can further be classified into hydrofluorocarbon and hydrocarbon. While the former has high global warming potential (GWP), the latter is flammable in nature. Their mixture in certain compositions is found to obviate both the demerits and perform equally well on thermodynamic scales for low T cycles. On the similar lines, mixture of HCs and inorganic fluids, such as propane+CO2 and isopentane+CO2 are found to be more appropriate for medium T applications if the issues like pinch temperature in the regenerator arising due to temperature glide are taken care of. In the high temperature domain, high efficiency Brayton cycle (supercritical CO2) and transcritical condensing cycles are studied with the latter being 2 % more efficient than the former. However, application of the condensing cycle is limited to low temperature ambient locations owing to low critical temperature of CO2 (304 K). In the same cycle configuration, mixture of CO2 and propane (52 and 48%) with a critical temperature of ~ 320 K is observed to retain the thermodynamic performance with the increased heat rejection temperature matched to the tropical ambient conditions. However, these cycles are plagued by the high operating pressures (~300 bar) calling for high temperature steel making the power block uneconomical. In this regard, the advanced CO2 cycles are developed wherein the optimum operating pressures are limited to 150 bar with an increased cycle efficiency of 6 % over the S-CO2 cycle. Feasibility study carried out on these cycles in the Indian context indicates the low and medium T cycles to be better suited for distributed power generation over the high T cycles. In the second part of work, a comprehensive study is performed to optimize the low and the medium T cycles on a thermo-economic basis for the minimum specific investment cost ($/We). Such a study involves development of component level models which are then integrated to form the system of interest, thus, following a bottom-up approach. A major emphasis is given on the development of scroll expander and low cost pebble bed thermal energy storage system that are the reported in the literature as the areas with high uncertainties while connecting them to the system. Subsequently, the key design parameters influencing the specific cost of power from an air-cooled ORC are identified and used to formulate a 7-dimensional space to search for the minimum costs for applications with a) geothermal/waste or biogas heat sources and b) solar ORCs. Corresponding maps of operating parameters are generated to facilitate distributed power engineers in the design of economic systems within constraints such as available heat source temperatures, maximum expander inlet pressures imposed, etc. Further, the effect of power scaling on these specific costs is evaluated for ORC capacities between 5 and 500 kWe.