his thesis deals with preparation of transparent ceramic sheets made out of sub-µm alumina powder. Green bodies are prepared by ultraviolet (UV) curing of UV curable resin containing ceramic powder followed by debinding of organic parts at elevated temperature. High relative density of green bodies is essential for reduction of shrinkage during subsequent sintering process. Therefore high solids loading dispersions containing > 57 vol% ceramic particles are used. To reach transparent behaviour, porosity within the sheets must be reduced completely. Therefore hot isostatic pressing (HIP) is used as a final operation. Finally, light transmission and hardness measurements are presented. Possibilities of making high resolution microstructures using maskless lithography and some suggestions for use of the UV curing technique for production of complex-shaped 3D structures are briefly mentioned.

No description available.

No description available.

A non-replicating recombinant adenovirus, Ad5MCMVlacZ, which expresses the 13-galactosidase (l3-gal) reporter gene, was used to examine both constitutive and inducible repair of UVC-damaged DNA in Chinese hamster ovary (CHO) cells. Host cell reactivation (HCR) of 13-gal activity for UVC-irradiated Ad5MCMVlacZ was examined in non-irradiated and UVC-irradiated nucleotide excision repair (NER) proficient parental CHO-AA8 and m mutant CHO-UV61 cells which are deficient in the transcription-coupled repair (TCR) pathway of NER. Cells were infected with either UVC-irradiated or non-irradiated Ad5MCMVlacZ and scored for 13-gal activity 24 h later. HCR of 13-gal activity for UVC-irradiated Ad5MCMVlacZ was significantly reduced in non-irradiated CHO-.UV61 cells compared to that in non-irradiated CHO-AA8 cells suggesting that repair in the transcribed strand of the UVC-damaged reporter gene in untreated CHO-AA8 cells utilizes TCR. Prior UVC-irradiation of cells with low UV fluences resulted in a transient enhancement of HCR for expression of the UVC-damaged reporter gene in CHO-AA8 cells but not m TCR deficient CHO-UV61 cells. Pre-UVC-treatment of cells resulted also in an enhanced expression of 13 -gal for unirradiated Ad5MCMVlacZ in both CHO-AA8 and CHO-UV61 cells. However, compared to CHO-AA8 cells, the CHO-UV61 cells exhibited comparable levels of enhanced 13-gal activity following significantly lower UVC exposures to cells suggesting that persistent damage in active genes plays a direct role in enhancing 13-gal activity driven by the MCMV promoter in CHO cells. These results suggest that prior UVC treatment results in a transient enhancement in repair of UVC-damage DNA in the transcribed strand of the active reporter gene in CHO-AA8 cells through an enhancement of TCR or a mechanism that involves the TCR pathway and that the upregulation of reporter gene expression alone is not sufficient for enhanced repair of the reporter gene in CHO-UV61 cells. The HCR assay was used also to examine both constitutive and inducible repair of UVC-damaged DNA in mouse embryonic fibroblast (MEF) cells. HCR of B-gal activity for UVC-irradiated Ad5MCMVlacZ was examined in non-irradiated and UVC-irradiated NER proficient parental wild type MEF cells and in MEF cells with specific knockouts in the p53 (p53-/-), pRb (pRb-/-), and p107 (p107-/-) genes. Cells were infected with either UVC-irradiated or non-irradiated Ad5MCMVlacZ and scored for ~-gal activity 24 h later. HCR of ~-gal activity for UVC-irradiated Ad5MCMVlacZ did not show a significant difference in non-irradiated cells for any of the MEF knockouts cells compared to the parental strain suggesting that p53, pRb and p107 does not play a role in repair of the UV -damaged reporter gene in untreated MEF cells. Prior UVC-irradiation of cells with low UVC fluences resulted in an enhancement of HCR for expression of the UV C-damaged reporter gene in MEF wild type cells, low passage pRb-/-and p 1 07 -I-MEF cells but not in p53-/-MEF cells or in high passage pRb-/-and p107-/-MEF cells. These results suggest that prior UVC treatment MEF cells results in an induced repair of UVC-damaged DNA that is dependent on p53. The presence of an enhancement of HCR for the UVC-damaged reporter gene in pre-UVC treated cells in low passage, but not in high passage, pRb-/-and p 1 07-I-cells suggests that the lack of pRb or pI 07 expression per-se does not result in a deficiency in inducible DNA repair. However, these results suggest that the lack of pRb or p 1 07 expression results in alterations in MEF cells at high passage number that abrogate inducible repair of UVC-damaged DNA. UVA produces predominantly single base damage that is repaired through base excision repair (BER), whereas UVC and UVB produce predominantly cyclobutane pyrimidine dimers (CPDs) and 6-4 photoproducts (6-4PP) that are repaired through NER. The colony survival following exposure to various UV sources was examined in cells proficient and deficient in (NER). The UV sources were a UVC source from a germicidal lamp emitting predominantly at 254 nm. and a UVA source from a lKW Hg-Xe arc lamp using either a Band pass filter (BPF) or a 335 Cut-off-filter (335COF). NER deficient CHO-UV5 and CHO-UV61 cells were more sensitive to UVC exposure compared to NER proficient CHO-AA8 cells, consistent with the production of UVC-induced DNA damage predominantly in the form of CPDs and 6-4PPs which are repaired through the NER pathway. NER deficient xeroderma pigmentosum cells from complementation group D (XPD) were more sensitive compared to NER proficient normal human cells following exposure to the UVA-BPF source. In addition XPDdenV cells, which express the denY gene from bacteriophage T4, were more resistant than XPD cells following exposure to the UVA-BPF source. Since the denY protein is specific for excision ofCPDs these results indicate a substantial proportion of the induced DNA damage resulting from the UV A-BPF is in the form of CPDs, presumably due to a significant UVB component in the beam. In contrast, the NER deficient CHO-UV5 and CHO-UV61 cells showed a similar sensitivity compared to the NER proficient CHO-AA8 cell line following UVA-335COF exposures up to 60 KJ/m2• However, for UVA-335COF exposures greater than 60 KJ/m2 the NER deficient cells were more sensitive compared to the NER proficient CHO-AA8 cells, although the difference in sensitivity between NER deficient and NER proficient cells was less than that detected following UV A-BPF exposure. These results suggest that the UVA-335COF exposure produces predominantly DNA damage of the single base type for exposures less 60 KJ/m2. This is consistent with the calculated spectral distribution, which showed a 5.62% UVB component for the UVA-BPF, but only 0.14% UVB component for the UVA-335COF. / Thesis / Master of Science (MS)

GE Healthcare Bio-Sciences AB in Umeå produce a variety of chromatography systems. One of the main components in chromatography is the UV module, which measure the light absorption of different wavelengths in the liquid being pumped through a cell. Currently at the Umeå site two types of UV-cells are produced; lab cells and industrial cells. The current test station for the industrial UV-cells is outdated, in disrepair and no longer supported.  GE has developed a test station for the lab cells that evaluates UV and flow properties, the data is stored in GE’s own production database, Prodas. The aim of this work is to design a test station for industrial UV-cells to improve the quality of the cells. The primary goal is a test station that can measure pressure, flow and absorption. The secondary goal is to discover and if possible, implement solutions that will streamline and automate the test station. A prototype of a test station for industrial UV-cells based on that for lab cells has been developed. The solution consists of an adapter that links the light path from the monitor through the UV-cell to the detector. The test station can measure pressure, flow and absorption but can only perform absorption and leakage tests.  Automation and efficiency have been accomplished in the form of scripts used to conduct absorption and leakage tests. The test station requires further development before it can be used in the production line. / GE Healthcare Bio-Sciences AB i Umeå tillverkar ett flertal system, ett av systemen är vätskekromatografen. Vätskekromatografen är en kemisk separationsmetod som använder sig av en UV-monitor, UV-detektor och en UV-cell för att mäta absorptionen av en lösning och framta koncentrationen av det eftersökta ämnet. På anläggningen i Umeå tillverkas två typer av UV-celler; laborationceller och industriceller. För labbcellerna har GE utvecklat en teststation som testar och utvärderar UV och flödesegenskaper samt lagrar data i GE:s egen produktionsdatabas, Prodas. Den befintliga stationen för industriceller är äldre och omodern, en utveckling behövs för att upprätthålla högre kvalité. Syftet med detta projekt är att uppdatera teststationen för industriella UV-celler till samma nivå som stationen för laborationsceller. Det primära målet är att konstruera och designa en teststation för industriella UV-celler som kan mäta tryck, flöde och absorption. Det sekundära målet är att upptäcka och om möjligt verkställa lösningar som kommer effektivisera och automatisera mätningarna. En prototyp av en teststation för industriella UV-celler baserat på den för laborationceller har framtagits, och består av en adapterlösning som används för att sammanlänka ljusbanan från monitorn genom flödescellen till detektorn. Prototypen kan enbart utföra absorption och läckagemätningar. Automatisering och effektivisering har utförts i form av scripts som används för att genomföra absorptions och läckagemätning. Teststationen kräver fortsatt vidareutveckling innan den kan används i produktionslinjen.

Depuis leurs découvertes dans les années 60 par Dewar, les composés BN-hétérocycliques ont subi un développement croissant, s’accentuant pendant la dernière décennie. Ce travail de thèse mené en collaboration avec le Pr S-Y LIU de Boston Collège (États-Unis) et le Pr L. WEBER de l’Université de Bielefeld (Allemagne), a permis la synthèse, ainsi que la caractérisation par spectroscopie photoélectronique à rayonnement UV de nouveaux systèmes. Dans une première partie représentée par les chapitres II, III et IV, nous abordons l’étude de la structure électronique des composés suivants : 1,2-dihydro-1,2-azaborine (1), N-Me-1,2-BN-toluene (2), N-Me-1,3-BN-toluene (3), 1,2-dihydro-1-aza-2-boranaphtalene (4), 1,2-dihydro-1-aza-2-boranthracene (5), 1,2-dihydro-1-aza-2-boranthracene (6), 1,2-dihydro-1-aza-2-boraphenanthrene (7), 1,3,2-benzodiazaborole (8), 1,9,8-benzodiazaborole (9), N-tert-butyl[1,3,2]diazaborolo[1,5-a]-pyridine (10), 1,3,2-trihydro[1,3,2]diazaborolo[1,5-a]-pyridine (11). Afin de compléter les propriétés physico-chimiques de ces nouveaux systèmes et d’aider à l’interprétation des spectres photoélectroniques, l’utilisation de calculs quantiques tels que la théorie de la fonctionnelle de la densité (DFT), la théorie fonctionnelle de la densité en fonction du temps (TD-DFT), la fonction de Green (OVGF), la méthode du troisième ordre partiel (P3), ou encore l’interaction de configuration (SAC-CI) ont été utilisées. Dans le Chapitre V, nous présentons une étude comparative entre les énergies ionisations théoriques et expérimentales. / Since the Dewar’s discovering in 60 years, the BN-heterocycles has experienced an important development during the last decade. This thesis presents our work on the synthesis and on the electronic structure characterization by Ultra-Violet photoelectron spectroscopy (UV-PES), followed in collaboration with the Pr SY LIU from the Boston College (USA) and the Pr L. WEBER from the University of Bielefeld (Germany). The first part corresponding to the chapter II, III and IV, describe the electronic structure analysis of: 1,2-dihydro-1,2-azaborine (1), N-Me-1,2-BN-toluene (2), N-Me-1,3-BN-toluene (3), 1,2-dihydro-1-aza-2-boranaphtalene (4), 1,2-dihydro-1-aza-2-boranthracene (5), 1,2-dihydro-1-aza-2-boranthracene (6), 1,2-dihydro-1-aza-2-boraphenanthrene (7), 1,3,2-benzodiazaborole (8), 1,9,8-benzodiazaborole (9), N-tert-butyl[1,3,2]diazaborolo[1,5-a]-pyridine (10), 1,3,2-trihydro[1,3,2]diazaborolo[1,5-a]-pyridine (11). In order to provide more information on the physical chemistry properties and to interpret the photoelectron spectra, the quantum chemical calculations of ionization energies have been followed using the Density Functional Theory (DFT), the Time-Dependent Density Functional Theory (TD-DFT), the Outer Valence Green’s Function (OVGF), the Partial third order (P3), the Symmetry Adapted Cluster-Configuration Interaction (SAC-CI). Moreover, the comparative analysis of theoretical and the experimental ionization energies are presented.

Ce travail s’intéresse à évaluer l’efficacité de procédés d’oxydation avancée pour l’élimination de pesticides dans l’eau, plus particulièrement l’acide 2,4-dichlorophénoxyacétique (2,4-D), un herbicide largement répandu, qui a été récemment classé comme cancérogène possible pour l’homme. Ces procédés utilisent différents types de rayonnement – UV/visible, ultrasons, rayons gamma –, seuls ou en combinaison avec des oxydants et/ou catalyseurs (ozone, peroxyde d’hydrogène, réactif de Fenton). L'influence du pH, de la dose d'oxydant, du type et de la concentration du catalyseur, du spectre d'irradiation lumineuse, de la dose de rayons gamma et de la fréquence ultrasonore est également analysée, de façon à déterminer par plans d’expériences les plages de fonctionnement optimales pour la conversion et la minéralisation du polluant. Parmi les procédés individuels, seules l’ozonation et l’oxydation Fenton homogène d’une part, la photolyse et l’irradiation gamma d’autre part permettent d’éliminer plus de 25% du carbone organique total en 1 heure. La sonolyse (à haute fréquence) apparaît comme le traitement moins performant, avec une dégradation du 2,4-D inférieure à 15% sur la même durée. Par ailleurs, des effets synergiques marqués sont mis en évidence en associant les différents types de rayonnement avec H2O2 ou le réactif de Fenton. Dans le dernier cas, le polluant est décomposé en moins de 10 minutes, tandis que le rendement de minéralisation est plus que doublé par rapport aux procédés séparés. Il en est de même pour le procédé couplé UV/O3 par rapport à l’ozonation et la photolyse seules. Ramenés à leur consommation énergétique, les traitements les plus efficaces sont, respectivement en termes de conversion et de minéralisation, l’oxydation radio-Fenton et l’oxydation photo-Fenton utilisant une lampe UV à basse pression de mercure. Par ailleurs, contrairement à la photolyse, ce dernier procédé est également activé par une lampe à arc Xenon, dont le spectre d’émission est proche de celui de la lumière du soleil. Sur la base de ces résultats, un photo-réacteur solaire à recirculation est mis en oeuvre pour traiter par oxydation photo-Fenton homogène des solutions de 2,4-D, préparées dans l’eau du robinet ou une eau résiduaire en entrée de station d’épuration. Dans les deux cas, la conversion du pesticide dépasse 95% en 1 heure et sa minéralisation 75% en 5 heures. Par ailleurs, l’eau ainsi traitée respecte tous les paramètres de qualité établis par la norme cubaine de rejet des eaux usées, en incluant une étape successive de neutralisation avec Ca(OH)2 et de filtration. Enfin, plusieurs parmi les meilleurs procédés sont évalués pour éliminer deux autres pesticides organochlorés, particulièrement toxiques et persistants dans l’environnement : le chlordécone et le bêta-hexachlorocyclohexane. Des résultats encourageants sont obtenus, avec une dégradation pratiquement totale des polluants en cinq heures, ce qui démontre l’intérêt des méthodes étudiées pour cette problématique. / This work investigates the efficacy of advanced oxidation processes for the remediation of pesticidesin water, more particularly 2,4-dichlorophenoxyacetic acid (2,4-D), a widely used herbicide that hasrecently been classified as a possible carcinogen to humans. These methods use different types ofradiation - UV / visible, ultrasound, gamma rays - alone or in combination with oxidants and / orcatalysts (ozone, hydrogen peroxide, Fenton’s reagent). The influence of pH, oxidant dose, catalysttype and concentration, light irradiation spectrum, gamma radiation dose and ultrasound frequencyis also analyzed, in order to determine by experimental design the optimal operating ranges for theconversion and mineralization of the pollutant. Of individual processes, only ozonation andhomogeneous Fenton oxidation on the one hand, photolysis and gamma irradiation on the otherhand, achieve the abatement of more than 25% of total organic carbon in one hour. (High frequency)sonolysis appears as the less efficient treatment, resulting in less than 15% of 2,4-D being degradedover the same duration.In addition, marked synergistic effects are demonstrated by combining the different types of radiationwith H2O2 or Fenton’s reagent. In the latter case, the pollutant is decomposed in less than 10 minutes,while the mineralization yield more than doubles compared to the separate processes. It is the samefor UV/O3 coupled process with respect to ozonation and photolysis alone. When accounting for theirenergy consumption, the most effective treatments are, respectively in terms of conversion andmineralization, radio-Fenton oxidation and photo-Fenton oxidation using a low-pressure mercuryvaporUV lamp. Moreover, unlike photolysis, the latter method is also activated by a Xenon arc lamp,whose emission spectrum is close to that of sunlight. Bases on these results, a solar photoreactoroperating in closed loop is used to treat 2,4-D solutions, prepared with tap water or inlet stream ofwastewater treatment plant, by homogeneous photo-Fenton oxidation. In both cases, the conversionof the pesticide exceeds 95% in 1 hour and its mineralization 75% in 5 hours. Moreover, the treatedwater complies with all the quality parameters established by the Cuban norm for wastewaterdischarge, when including a subsequent step of neutralization with Ca(OH)2 and filtration.Finally, several of the best processes are evaluated to eliminate two other organochlorine pesticides,particularly toxic and persistent in the environment: chlordecone and beta-hexachlorocyclohexane.Encouraging results are obtained, with an almost complete degradation of the pollutants in fivehours, which demonstrates the value of the investigated methods for this issue. / En este trabajo se estudió la factibilidad de diferentes procesos avanzados de oxidación para laeliminación de plaguicidas en aguas, específicamente el ácido 2,4-diclorofenoxiacético (2,4-D), unode los herbicidas más utilizados a nivel mundial y que recientemente ha sido clasificado comocancerígeno para el hombre. Estos procesos utilizan diferentes tipos de irradiación – UV/Visible,ultrasonido, radiación gamma – solos o en combinación con oxidantes y/o catalizadores (ozono,peróxido de hidrógeno, reactivo de Fenton). Con el objetivo de determinar las condiciones óptimaspara la degradación y mineralización del contaminante, se analizó la influencia del pH, la dosis deoxidante, el tipo y la concentración del catalizador, el espectro de irradiación luminosa, la dosis deirradiación gamma y la frecuencia y potencia ultrasónicas. Entre los procesos individuales,solamente la oxidación Fenton homogénea, la ozonización, la fotólisis y la radiación gamma lograroneliminar más de un 25% del carbono orgánico total en una hora. La sonólisis (a alta frecuencia)resultó el proceso menos eficiente, con una degradación del 2,4-D inferior al 15% en el mismotiempo.Al asociar los diferentes tipos de irradiación con el H2O2 o el reactivo de Fenton, se observaronefectos sinérgicos importantes. Para este último, el contaminante se degradó totalmente en menosde 10 minutos, mientras que la mineralización fue superior al doble de la obtenida para los procesospor separado. Lo mismo ocurrió para el proceso combinado UV/O3, respecto a los procesos defotólisis y ozonización solos. Teniendo en cuenta el consumo energético asociado a la degradacióny mineralización respectivamente, los tratamientos más eficientes fueron el radio-Fenton y el foto-Fenton utilizando una lámpara de baja presión de mercurio. Por otra parte, al contrario de la fotólisis,este último proceso se activó con una lámpara de arco de Xenon, la cual posee un espectro deemisión cercano a la luz solar. Teniendo en cuenta estos resultados, se realizó un grupo deexperimentos a escala de banco utilizando un foto-reactor solar, donde se trataron por oxidaciónfoto-Fenton homogénea disoluciones de 2,4-D preparadas con agua técnica y agua residualobtenida a la entrada de una planta de tratamiento de aguas. En los dos casos, la degradación delpesticida supera el 95% en 1 hora y su mineralización en 75% en 5 horas. Además, al incluir unaetapa de neutralización con Ca(OH)2, el agua residual tratada logra cumplir las normas de calidadestablecidas por la norma cubana de vertimiento de aguas residuales.Finalmente, algunos de los procesos con mejores resultados se evaluaron para la eliminación otrosdos pesticidas organoclorados de mayor toxicidad y persistencia en el medio ambiente: laclordecona y el beta hexaclorociclohexano. Al aplicar las técnicas de tratamiento a estoscompuestos se lograron buenos resultados, cercanos a la degradación total de ambos plaguicidasen cinco horas, lo que demuestra el interés de los métodos estudiados en esta tesis.

<p>One of the outstanding goals of neuroscience is to understand how neural circuits are assembled to produce context appropriate behavior. In an ever changing environment, it is critical for animals to be able to flexibly respond to different stimuli to optimize their behavioral responses accordingly. Oviposition, or the process of choosing where to lay eggs, is an important behavior for egg-laying animals, yet the neural mechanisms of this behavior are still not completely understood. Here, we use the genetically tractable organism, Drosophila melanogaster, to investigate how the brain decides which substrates are best for egg deposition. We show that flies prefer to lay eggs away from UV light and that induction egg-laying correlates with increased movement away from UV. Both egg-laying and movement aversion of UV are mediated through R7 photoreceptors, but only movement aversion is mediated through Dm8 amacrine neurons. We then identify octopaminergic neurons as being potential modulators of egg-laying output. Collectively, this work reveals new insights into the neural mechanisms that govern Drosophila egg-laying behavior.</p> / Dissertation

Syfte - Studien syftar till att undersöka om det har skett en förändring angående solning i solarier från 2006/2007 fram till 2015/2016 hos individer i Sverige mellan 18-24 år. Samt att studera om det har någon betydelse till vilket kön, utbildningsnivå och hudtyp man tillhör i förhållandet till hur mycket Minimal Erythemal Dose (MED) man utsätter sig för under 2016. Metod – Metoden som användes var en kvantitativ mätmetod där en webbenkät användes som verktyg. Enkäten skickades ut på en social plattform. Resultat - 193 personer svarade varav 127 passade in i målgruppen, 99 var kvinnor och 28 var män. 76 personer hade läst på universitet eller en högskola, 50 personer angav gymnasie som högsta utbildningsnivå och en person hade grund-/folk-/realskola eller liknande som svar. Vad det gäller hudtyp så var det 96 personer med hudtyp I, 27personer med hudtyp II, 3 personer med hudtyp III och en person med hudtyp IV. Det visade sig att det inte har skett en statistisk signifikant förändring mellan en studie som gjordes åren 2006/2007 och den här studien från 2015/2016 angående solning i solarium (χ2 (5) = 3.902, p &lt; .05). Dock visade det sig att det finns en skillnad mellan könen i deras UV-exponering (p=0,033). Utbildningsnivåer (p= 0,896) och hudtyper (p= 0,117) skiljer sig inte signifikant från varandra. Det fanns heller inget signifikant samband mellan utbildningsnivå och MED (p=0,897) eller mellan hudtyp och MED (p=0,079). Medianvärdet av den totala UV-exponeringen är 61,18 MED där den undre kvartilen ligger på 29,37 MED och den övre kvartilen ligger på 105,54 MED. UV-exponering i solarium har ett medianvärde av 0,0 MED där den undre kvartilen ligger på 0,0 MED och den övre kvartilen ligger på 5,0 MED. Slutsats - Sveriges arbete för att motverka solarium kan utvecklas då det har visat sig att det inte har skett en förändring på 10 år. Framtida studier skulle kunna rikta sig mot varför det inte har förändrats och hur man ska utforma interventioner som människor faktiskt kan ta till sig.

Delafossite CuFeO2 is an intrinsic p-type semiconductor with a band gap around 1.5 eV. Further, it is composed of relatively abundant, nontoxic elements, and therefor have potential to be an attractive material for solar energy harvesting.This work examines three routes to synthesise this material. The first includes a sol-gel deposition and then relies on solid state reaction above 650 degrees Celsius in inert gas atmosphere. In this work, no delafossite is obtained with this method.The second method is a hydrothermal route to make particles under hydrostatic pressure in an autoclave. Delafossite is obtained mixed with other phases.The third route includes aqueous precipitation similar to the second route, but a temperature of 70 degrees Celsius and ambient pressure is sufficient to produce a pure delafossite particle phase. It provides a robust and simple way to make delafossite CuFeO2 particles.The resulting particles are deposited and compressed on glass into thin films.The films have a band gap slightly below 1.5 eV and show some photoactivity in electrochemical measurements.