Les oxydes fortement corrélés sont largement étudiés pour l'hôte d'applications uniques, telles que la supraconductivité à haute température, la magnéto-résistance colossale, les commandes exotiques magnétiques, chargées et orbitales et les transitions isolant-métal. Les oxydes métalliques de transition qui forment la majorité des systèmes d'oxydes corrélés et des oxydes de vanadium, en particulier VO2 et V2O5, sont les deux systèmes les plus préférés parmi les chercheurs pour plusieurs applications. Dans cette thèse, la croissance et la caractérisation de VO2 et V2O5 sont discutées avec un accent particulier sur la propriété optique, en particulier les propriétés thermochromiques. Traditionnellement, le comportement SMT et l'infrarouge reflètent la zone de focalisation pour la recherche VO2 et c'est seulement jusqu'à récemment que la VO2 est traitée comme un système beaucoup plus complexe et a été étudiée comme un métamatériel naturellement désordonné très réactif près de la température de transition de phase où le matériau présente des matériaux semi-conducteurs et métalliques Coexistence de phase. Étant donné que chaque phase de VO2 a des propriétés optiques et électriques distinctes, elle contrôle l'étendue des transitions de phase par une modulation de température précise, permet d'exploiter le matériau pour de nouvelles propriétés, comme la modulation d'émissivité dans la région NIR et pour la création de motifs IR réversibles et réinscriptibles. Le V2O5 est traditionnellement considéré comme un matériau TCR élevé et considéré comme un matériau de choix pour une application allant de la catalyse, des capteurs de gaz aux batteries au lithium. Dans cette étude, nous nous concentrons sur les propriétés optiques du matériau, en particulier la nature thermochromique de la gamme visible des revêtements V2O5 synthétisés par recuit oxydatif des revêtements VOx développés par MOCVD. L'impact du dopage et de la production sélective de vacance d'oxygène sur la propriété thermochromique est discuté. / Strongly correlated oxides are studied widely for the host of unique applications, such as hightemperature superconductivity, colossal magneto resistance, exotic magnetic, charge and orbital ordering, and insulator-to-metal transitions. Transitional metal oxides which form the majority of the correlated oxide systems and oxides of Vanadium, especially VO2 and V2O5 are the two most favourite systems among researchers for several applications. In this thesis, the growth and characterization of VO2 and V2O5 are discussed along with a special focus on the optical property, especially thermochromic properties. Traditionally SMT behaviour and Infrared reflectively was the focus area for VO2 research, and its only until recently that VO2 is being treated as a much more complex system and investigated as highly responsive naturally disordered metamaterial near the phase transition temperature where the material exhibits semiconducting and metallic phase co-existence. Since each phase of VO2 has a distinct optical and electrical properties, controlling the extent of phase transitions by accurate temperature modulation, enables exploitation of the material for new properties like emissivity modulation in the NIR region and for creating IR visible reversible and rewritable patterns. V2O5 is traditionally seen as a high TCR material and regarded as material of choice for application ranging from catalysis, gas sensors to lithium batteries. In this study, however we focus on the optical properties of the material, especially the visible range thermochromic nature of V2O5 coatings synthesised by oxidative annealing of MOCVD grown VOx coatings. The impact of doping and selective oxygen vacancy generation on the thermochromic property are discussed.

Gold black porous coatings were thermally evaporated in the chamber backfilled with inert gas pressure and their optical properties were studied in near-far-IR wavelengths. The porosities of coatings were found to be extremely high around ~ 99%. Different approaches of effective medium theories such as Maxwell-Garnett, Bruggeman, Landau-Lifshitz-Looyenga and Bergman Formalism were utilized to calculate refractive index (n) and extinction coefficient (k). The aging induced changes on electrical and optical properties were studied in regular laboratory conditions using transmission electron microscopy, Fourier transform infrared spectroscopy, and fore-probe electrical measurements. A significant decrease in electrical resistance in as deposited coating was found to be consistent with changes in the granular structure with aging at room temperature. Electrical relaxation model was applied to calculate structural relaxation time in the coatings prepared with different porosities. Interestingly, with aging, absorptance of the coatings improved, which is explained using conductivity form of Bergman Formulism. Underlying aim of this work was to utilize gold blacks to improve sensitivity in un-cooled IR sensors consist of pixel arrays. To achieve this, fragile gold blacks were patterned on sub-mm length scale areas using both stenciling and conventional photolithography. Infrared spectral imaging with sub-micron spatial resolution revealed the spatial distribution of absorption across the gold black patterns produced with both the methods. Initial experiments on VOx-Au bolometers showed that, gold black improved the responsivity by 42%. This work successfully establishes promising role of gold black coatings in commercial un-cooled infrared detectors.

Die vorliegende Habilitationsschrift bespricht aktuelle Ergebnisse zur Struktur und Reaktivität von Übergangsmetalloxidoberflächen. Es werden eingangs Grundlagen zur Berechnung von Eigenschaften von Oberflächen mittels Dichtefunktionaltheorie vorgestellt. Des Weiteren werden anhand von drei untersuchten Oxiden, nämlich dem Vanadium(III)-oxid, dem Cer(IV)-oxid, und dem Eisen(II,III)-oxid, der aktuelle Forschungsstand im Hinblick auf Oberflächenstruktur und Reaktivität von Phasengrenzen, wie z.B. der Phasengrenze zwischen Vanadium(V)-oxid und Cer(IV)-oxid und der Phasengrenze zwischen Wasser und Eisen(II,III)-oxid dargelegt. / The present habilitation thesis discusses results on structure and reactivity of transition metal oxide surfaces obtained using state-of-the-art density functional theory methods. First, fundamental issues of density functional theory are presented. Furthermore, the current state in research with respect to surface structure on one hand and reactivities of interfaces between different oxides like vanadium(III) and cerium(IV) oxide or water and iron(II,III) oxide on the other hand are developed.

No description available.

Em ultimas décadas, a conversão de alcanos leves em suas correspondentes olefinas tem sido objeto de intensas pesquisas, impulsionadas inclusive pelo aumento crescente da demanda do propileno como um importante produto petroquímico. A desidrogenação oxidativa (ODH) do propano representa uma via alternativa promissor para a produção de propeno, ao apresentar-se como uma reação exotérmica e não limitada termodinamicamente. Diferentes óxidos suportados ou mistos têm sido desenvolvidos com a finalidade de aumentar a atividade e seletividade em relação as olefinas. Metais alcalinos são importantes agentes promotores que proporcionam uma melhor seletividade as olefinas devido a redução da acidez e aumento da basicidade da superfície do catalisador. A proposta deste presente trabalho foi desenvolver metodologias de síntese de catalisadores de oxido de vanádio suportado em aluminas de diferentes fases cristalinas e dopados com sódio ou potássio a fim de avalia-los em testes catalíticos de desidrogenação oxidativa do propano. Para tanto, foram utilizadas as seguintes técnicas de caracterização: volumetria N2, difratometria de raios X (DRX) e redução a temperatura programada (RTP). As características acidas e/ou básicas dos suportes e catalisadores foram avaliadas pelas reações de decomposição de isopropanol. / In recent decades, the conversion of light alkanes to their corresponding olefins has been the subject of intense research, mainly driven by the increasing demand of propylene as an important petrochemical product. Oxidative dehydrogenation (ODH) propane is a promising alternative way to propylene production, which it is presented as an exothermic reaction and not limited thermodynamically. Different supported or mixed oxides have been developed in order to increase the activity and selectivity to olefins. Alkali metals are important promoters, which provide improved selectivity to olefins due to reduction of acidity and increasing basicity of the catalyst surface. The purpose of the present study was to develop synthesis methods of vanadium oxide catalysts supported on alumina of the different crystalline phases and doped with sodium or potassium in order to evaluate them in catalytic tests of propane oxidative dehydrogenation. For in such a way, the following characterization techniques were used: N2 volumetry, X-ray diffractometry (XRD) and temperature programmed reduction (TPR). The properties acid and/or basic of supports and catalysts were evaluated by the isopropanol decomposition reaction.

Em ultimas décadas, a conversão de alcanos leves em suas correspondentes olefinas tem sido objeto de intensas pesquisas, impulsionadas inclusive pelo aumento crescente da demanda do propileno como um importante produto petroquímico. A desidrogenação oxidativa (ODH) do propano representa uma via alternativa promissor para a produção de propeno, ao apresentar-se como uma reação exotérmica e não limitada termodinamicamente. Diferentes óxidos suportados ou mistos têm sido desenvolvidos com a finalidade de aumentar a atividade e seletividade em relação as olefinas. Metais alcalinos são importantes agentes promotores que proporcionam uma melhor seletividade as olefinas devido a redução da acidez e aumento da basicidade da superfície do catalisador. A proposta deste presente trabalho foi desenvolver metodologias de síntese de catalisadores de oxido de vanádio suportado em aluminas de diferentes fases cristalinas e dopados com sódio ou potássio a fim de avalia-los em testes catalíticos de desidrogenação oxidativa do propano. Para tanto, foram utilizadas as seguintes técnicas de caracterização: volumetria N2, difratometria de raios X (DRX) e redução a temperatura programada (RTP). As características acidas e/ou básicas dos suportes e catalisadores foram avaliadas pelas reações de decomposição de isopropanol. / In recent decades, the conversion of light alkanes to their corresponding olefins has been the subject of intense research, mainly driven by the increasing demand of propylene as an important petrochemical product. Oxidative dehydrogenation (ODH) propane is a promising alternative way to propylene production, which it is presented as an exothermic reaction and not limited thermodynamically. Different supported or mixed oxides have been developed in order to increase the activity and selectivity to olefins. Alkali metals are important promoters, which provide improved selectivity to olefins due to reduction of acidity and increasing basicity of the catalyst surface. The purpose of the present study was to develop synthesis methods of vanadium oxide catalysts supported on alumina of the different crystalline phases and doped with sodium or potassium in order to evaluate them in catalytic tests of propane oxidative dehydrogenation. For in such a way, the following characterization techniques were used: N2 volumetry, X-ray diffractometry (XRD) and temperature programmed reduction (TPR). The properties acid and/or basic of supports and catalysts were evaluated by the isopropanol decomposition reaction.

This thesis reports both the optimizations of the vanadium oxide (VOx) thin film as an active infrared detector material by the magnetron sputtering deposition method and its use during fabrication of proper resistors for the microbolometers. Vanadium oxide is a preferred material for microbolometers, as it provides high TCR value, low noise, and reasonable resistance, and a number of high-tech companies have used this material to obtain state-of-the-art microbolometer arrays. This material is first used in microbolometers by Honeywell, who provides its recipe with license agreements, and there is not much information in the literature for its deposition recipe. This is the first study at METU for development of vanadium oxide thin film for microbolometers. The VOx material deposition studies started by identifying the deposition parameters of the magnetron sputtering system in order to obtain proper VOx resistors for the readout electronics. The obtained recipe includes high temperature deposition conditions of VOx, however, this causes a diffusion problem on the electrodes, preventing to obtain a good contact to VOx. Also, high oxygen level in the depositions makes a contamination on the electrodes. A number of studies were done to determine a proper electrode material which is proper with the deposition conditions of the VOx. Characterization of the vanadium oxide samples is done by XRD and XPS measurements to see the relation between the phases and resistivity of the vanadium oxide. It is known that V2O5 phase provides a high TCR and resistivity value, and the XRD results show that this phase is dominant in the highly-oxygen doped or annealed resistors. The TCR and noise measurements are done using resistors implemented with the developed VOx film, after the etching processes of the both VOx and the electrodes are optimized. The contamination on the electrodes is prevented by the help of a newly designed process. The TCR measurement results show that annealing of the resistors affect the TCR values, i.e., increasing the annealing duration increases the TCR values of the resistors. Two different resistors with different deposition conditions are annealed to see the effect of annealing, where TCR results of the resistors are -0.74%/K and -0.8 %/K before annealing. The TCR values of these resistors increase to -1.6 %/K and -4.35 %K, respectively, after annealing in same conditions, showing that both the deposition conditions and annealing change the TCR significantly. Although good TCR values are obtained, the noise values of the VOx resistors are much higher than the expected values, which suggest a further study to determine the cause of this noise.

This thesis reports the development of Vanadium Tungsten Oxide (VWO) film as an active detector material for uncooled infrared detectors by using the reactive DC magnetron co-sputtering method. VWO is a doped form of the Vanadium Oxide (VOx) which is known as a prominent material for uncooled infrared detectors with its high TCR, low resistivity, and low noise properties. VOx is a widely preferred material for commercialized uncooled infrared detectors along with its drawbacks. Fabrication is fairly difficult due to its unstable material properties and the need for low process temperatures for a monolithic, CMOS compatible surface micromachining process. Hence, a new material with high performance and easier fabrication is needed. This thesis is the first study at METU on the development of high-performance VWO as an active detector material for uncooled infrared detectors. Deposition studies of VWO primarily started by measuring the effects of deposition parameters upon the magnetron sputtering system. Because the high effectiveness of the tungsten doping has been obtained for the doping level below 10% according to literary information, maximum vanadium (V) deposition rate together with minimum tungsten (W) deposition rate has been initially aimed. TCR of the VWO films has been measured between -2.48 %/K and -3.31 %/K, and the variation of noise corner frequency from 0.6 kHz to 8 kHz has been observed. In addition to these results of VWO, a favorable VOx recipe which has the highest performance done at METU in terms of resistance, TCR, noise and uniformity has also attained during the studies. Structural characterization of VWO is achieved using XPS, XRD, and AFM characterization techniques. Other than the sputtering parameters, post-annealing process and oxygen plasma exposure was examined as well. A general observation of the post-annealing is that it decreases not merely the TCR but also the noise of the deposited film. A short-period oxygen plasma exposure has a constructive effect on the noise behavior. Fabricated vanadium tungsten oxide with sandwich type resistor structure shows very close but better bolometric properties when compared with the yttrium barium copper oxide (YBCO), which is another material being studied in scope of other theses at METU. XPS, XRD and AFM characterization methods have been used for the structural characterization of vanadium-tungsten-oxide.

The atmosphere we live in contains various kinds of chemical species, natural and artificial, some of which are vital to our life, while many others are more or less harmful. The vital gases like oxygen, humidity have to be kept at adequate levels in the living atmosphere, whereas the hazardous and toxic gases like hydrocarbons, H2, volatile organic compounds, CO2, CO, NOx, SO2, NH3, O3 etc should be controlled to be under the designated levels. The measurement technology necessary for monitoring these gases has emerged, particularly as organic fuels and other chemicals have become essential in domestic and industrial life. In addition to other applications, environmental pollution monitoring and control has become a fundamental need in the recent years. Therefore, there has been an extensive effort to develop high-performance chemical sensors of small size, rugged construction, light weight, true portability, and with better sensing characteristics such as high sensitivity, fast response and recovery times, low drift, and high degree of specificity. Among the various types of gas sensors studied, solid state gas sensors based on semiconducting metal oxides are well established, due to their advantages over the other types, and hence cover a wide range of applications. However, the widespread application of these sensors has been hindered by limited sensitivity and selectivity. Various strategies have been employed in order to improved the performance parameters of these sensors. This thesis work has two major investigations, which form two parts of the thesis. The first part of this thesis describes the efforts to improve the sensing behaviour of one of the extensively studied metal oxide gas sensors, namely, ZnO, through a novel, ultrasonic-nebulised spray pyrolyis synthesis method, employing an aqueous combustion mixture (NSPACM). The second part of the thesis deals with the ideal of gas detection by optical means through the reversible phase transformation between V2O5 and V6O13 deposited by metalorganic chemical vapor deposition(MOCVD). The introductory chapter I deals with basics of chemical sensors and the characteristic sensing parameters. Different types of gas sensors based on the phenomena employed for sensing are discussed, with an emphasis on semiconducting metal oxide gas sensors. The importance of material selection for solid state gas sensors, depending on the purpose, location, and conditions of operation are discussed, supporting the assertion that semiconducting metal oxides are better suited to fulfill all the requirements of modern gas sensors. Some of the effective methods to improve performance parameters including the influence of grain size, microstructure, and surface doping are described., followed by the motivation of the present thesis. The part I of the thesis is based on the resistive semiconducting metal oxide, where the system investigated was ZnO. Part one comprises Chapters 2, 3 and 4. In Chapter 2, a brief introduction to the material properties of ZnO, followed by various synthesis techniques are discussed. An overview of spray pyrolysis and combustion synthesis is followed by the details of the method employed in the present study, namely NSPACM, which is based on the above two methods, for the formation of ZnO films. A detailed description of the film deposition system built in house is presented, followed by the deposition procedure and the parameters used. Thermal study of the combustion mixture and non-combustion precursor shows the importance of the fuel, along with oxidizer, in forming the film. The films formed using combustion mixture are found to be polycrystalline, whereas films formed without combustion were found to have preferred crystallographic orientation even on an amorphous substrate, which is explained on the basis of minimization of surface energy. The observed unique microstructure with fine crystallite size and porous morphology is attributed to the combustion method employed, which is interesting from the point of view of gas sensing. Chapter 3 concerns the gas sensing study of these ZnO films. The design of the home made gas sensing system is explained in detail. The study of electrode characteristics is followed by the important steps in gas sensing measurements. ZnO gas sensors were mainly studied for their selectivity between aliphatic and aromatic hydrocarbons. The results show two regions of temperature where the sensitivity peaks for aliphatic hydrocarbons, whereas aromatic hydrocarbons show a single sensitive region. This observation can pave the way for imparting selectivity. Possible reasons for the observed behavior are mentioned. Chapter 4 describes the chemical and physical modifications done to ZnO thin films by doping with catalysts, and through the use of x-y translational stage for large-area deposition.. Homogenous distribution of catalysts achieved by the NSPACM synthesis procedure, determined by the x-ray elemental mapping, is discussed. The addition of catalysts improved the sensing both because of catalytic effects and by promoting preferred crystallographic orientation, with Ni addition showing the better effects. The use of the x-y stage in producing the films with high orientation, which improved the gas sensing behavior, is explained. Part II of the thesis comprises Chapters 5,6 and 7, and describes a detailed study of V2O5 and V6O13 thin films deposited by MOCVD for optical sensing of chemical species. In Chapter 5, a brief introduction to chemical vapor deposition is given, followed by the importance of the characteristics of CVD precursors – in particular, the importance of their thermal behavior in film formation. This is followed by the importance of vapor pressure and partial pressure studies in the MOCVD of oxides of a multivalent metal such as vanadium. Various techniques of measuring vapor pressure are listed, followed by the details of the method used in the present study employing rising temperature thermogravimetry, based on the Langmuir equation. Thermogravimetric analysis performed, both at atmospheric as well as at low pressure, using commercial and home made apparatus, respectively is discussed. A detailed description of the home made setup is also presented. Chapter 6 describes the application of the vapor pressure and partial pressure studies to the deposition of films using MOCVD. Here, a detailed description of the vanadium oxide phase diagram and the stability of various phases is presented, which points the importance of precise parameter control during the deposition to obtain pure phases. The details of the CVD setup, followed by the procedure and parameters of deposition, are presented. The films deposited at various deposition temperatures, analyzed using XRD and SEM, are discussed. The effect of temperature on the growth is explained. The effect of vapor pressure is studied by varying the precursor vaporizer temperature, with a growth temperature maintained invariant. The influence of the amount of precursor on film growth, with a particular crystalline orientation and phase content, is explained followed by the description of the deposition of pure phases of V2O5 and V6O13 through the optimization of CVD parameters. Chapter 7 deals with the optical study of the films deposited by the above method. Here, the importance of two phases of vanadium oxide, V2O5 and V6O13, to the proposed gas sensing action, is presented. Their structural similarity in terms of polyhedral arrangement in the ab plane can be the basis of a reversible phase change. The difference in the optical transmittance in two phases forms the basis for the optical method for chemical sensing. The details of the laser-based optical sensing setup, its, design and the detection method, are explained. Studies on hydrocarbon sensing with vanadium, pentoxide films are also presented. The novelty in using reversible chemical transformation of a material system for detection of reducing and oxidizing gases in the ambient gases is discussed. Chapter 8 provides a summary of the present thesis, together with the main conclusions. The work reported in this thesis has been carried out by the candidate as part of the Ph.d training programme. She hopes that this would constitute a worthwhile contribution towards the understanding and subsequent application of ZnO and oxides of vanadium(V2O5 and V6O13) as novel gas sensors which will be useful for environmental protection, as well as for safety in industrial an domestic sectors.

Many transition metal oxides exhibit a Metal-Insulator Transition (MIT). This is an interesting phenomenon where the material undergoes a structural phase transition, and the electronic charge is redistributed in the crystal lattice. The crystallographic, optical, electrical, and magnetic properties are drastically changed when a material undergoes a MIT. Vanadium oxides are thermochromic materials, which means that the optical properties change with temperature, closely connected to the MIT. Vanadium sesquioxide (V2O3) experiences a MIT at the transition temperature (Tt) 160-170 K. Below the transition temperature, it is a monoclinic ferromagnetic insulator, and above the transition temperature it becomes a paramagnetic rhombohedral corundum-type metal. In the insulating phase, infrared (IR) light is transmitted, whereas in the metallic phase, IR light is reflected. The aim of this Master thesis is to improve the methodology to produce V2O3 thin films, characterize them, and study how different parameters affect the structural and optical properties of the film. V2O3 thin films were synthesized by sol-gel and deposited by spin-coating on sapphire substrates. Thereafter, the resulting films underwent an annealing process in a reducing atmosphere to achieve crystalline V2O3. The obtained crystal phase was examined by X-ray diffraction. The surface structure and morphology were studied with an optical microscope and scanning electron microscope. The optical transmittance in the IR region was examined by Fourier transform infrared spectroscopy. At last, a laser test was performed on one of the samples. In conclusion, a majority of the thin films consisted of polycrystalline V2O3. The MIT was studied with the optical hysteresis loop, which showed great difference among the different samples studied. The thin film that exhibited best optical properties showed a maximum transmission of 66 % below the Tt, and a minimum transmission of 6 % above the Tt. In comparison to this one, the other samples exhibited lower transmission and a decrease in Tt. This difference was attributed to the different morphologies and crystal orientations of the samples.