The field of micro total analysis systems (μTAS) aims at developments toward miniaturized and fully integrated lab-on-a-chip systems for applications, such as drug screening, drug delivery, cellular assays, protein analysis, genomic analysis and handheld point-of-care diagnostics. Such systems offer to dramatically reduce liquid sample and reagent quantities, increase sensitivity as well as speed of analysis and facilitate portable systems via the integration of components such as pumps, valves, mixers, separation units, reactors and detectors. Precise microfluidic control for such systems has long been considered one of the most difficult technical barriers due to integration of on-chip fluidic handling components and complicated off-chip liquid control as well as fluidic interconnections. Actuation principles and materials with the advantages of low cost, easy fabrication, easy integration, high reliability, and compact size are required to promote the development of such systems. Within this thesis, liquid displacement in microfluidic applications, by means of expandable microspheres, is presented as an innovative approach addressing some of the previously mentioned issues. Furthermore, these expandable microspheres are embedded into a PDMS matrix, which composes a novel thermally responsive silicone elastomer composite actuator for liquid handling. Due to the merits of PDMS and expandable microspheres, the composite actuator's main characteristic to expand irreversibly upon generated heat makes it possible to locally alter its surface topography. The composite actuator concept, along with a novel adhesive PDMS bonding technique, is used to design and fabricate liquid handling components such as pumps and valves, which operate at work-ranges from nanoliters to microliters. The integration of several such microfluidic components promotes the development of disposable lab-on-a-chip platforms for precise sample volume control addressing, e.g. active dosing, transportation, merging and mixing of nanoliter liquid volumes. Moreover, microfluidic pumps based on the composite actuator have been incorporated with sharp and hollow microneedles to realize a microneedle-based transdermal patch which exhibits on-board liquid storage and active dispensing functionality. Such a system represents a first step toward painless, minimally invasive and transdermal administration of macromolecular drugs such as insulin or vaccines. The presented on-chip liquid handling concept does not require external actuators for pumping and valving, uses low-cost materials and wafer-level processes only, is highly integrable and potentially enables controlled and cost-effective transdermal microfluidic applications, as well as large-scale integrated fluidic networks for point-of care diagnostics, disposable biochips or lab-on-a-chip applications. This thesis discusses several design concepts for a large variety of microfluidic components, which are promoted by the use of the novel composite actuator. Results on the successful fabrication and evaluation of prototype devices are reported herein along with comprehensive process parameters on a novel full-wafer adhesive bonding technique for the fabrication of PDMS based microfluidic devices. / QC 20100817

Damages of metallic aircraft structures that occur during manufacturing, assembly and in service require local repair. Especially with current service-life extensions of ageing aircraft fleets, the importance of such repair methods is increasing. Typically, the repair of smaller damages on aluminium fuselage or wing skins is done by riveting a patch onto the flawed structure. However, the use of rivets reduces the strength of the structure and promotes fatigue. Joining the patch by adhesive bonding would not only offer more homogenous load distribution and weight savings, but even an increase of structural integrity. Metal adhesive bonding is commonly used in aeronautics, but requires elaborated surface treatments of the adherends, employing hazardous chemicals like chromates, due to the high durability demands. Furthermore, these treatments are usually tank processes that are not suitable for local repairs. Hence, there is a strong need for locally applicable surface preparation methods that allow safe and reliable adhesive bonding of primary aircraft structures. The aim of this thesis is to assess the – still emerging – method of atmospheric pressure plasma deposition of silicon (Si) containing compounds concerning its suitability as surface preparation for adhesive bonding of aluminium aerostructures. Atmospheric plasma deposition is not yet used in the aircraft industry, and the knowledge on functionality of this technology concerning bonding of aluminium parts is limited. Moreover, the durability requirements of the aircraft industry greatly exceed the standards in other industries. Hence, special attention is paid to a thorough analysis of the key characteristics of the deposited coupling films and their effectiveness in terms of adhesion promotion as well as joint durability under particularly hostile conditions. In order to do so, the altering mechanisms of the treated joints and the behaviour of the coupling films during accelerated ageing will be investigated in detail for the first time in this thesis. Furthermore, the influence of the aluminium surface pre-treatment (i.e. topography and oxide properties of the substrate) on the overall joint performance after coupling film deposition is thoroughly examined. Based on these findings, the surface preparation is optimised, and a process is developed to achieve maximal joint performance. As alternative local surface treatments prior to adhesive bonding, solution derived deposition of silane and sol-gel films have already been widely investigated and can be considered as reference, even though these techniques are rarely used in civil aeronautics. The knowledge on their effectiveness and capabilities in corrosive atmosphere is still very limited. Therefore, all analyses of degradation mechanisms are conducted for both plasma deposition and wet-chemical reference treatments to reveal the differences and communalities of the two Si-based coupling films. Physical and chemical analysis of the films, the oxides and the interfaces reveal differing, but interdependent failure mechanisms that are inhibited differently by the individual coupling films. Using the optimum deposition parameters, plasma films of only several nanometres in thickness significantly enlarge the corrosion resistance of bonded joints, reaching almost the level of anodising treatments with several micrometres thick oxides and strongly outperforming solution derived silane treatments. However, plasma film performance is found to be largely dependent on the precursor selection. With plasma deposition of 3-glycidoxypropyltrimethoxysilane, which has not been reported before, highest joint stability is achieved. Moreover, it is discovered that the properties of plasma and solution derived silane based films are complementary. It is shown that an optimised combined plasma and wet-chemical treatment process provides even superior resistance to bondline corrosion than state-of-the-art anodising techniques.

L’assemblage des matériaux composites thermoplastiques tel que le PEEK est l’une des problématiques majeure de l’industrie aéronautique. Actuellement, différentes techniques sont développées pour assurer l’assemblage structural de ces matériaux, tels que : le soudage, le rivetage, le boulonnage et le collage. Les enjeux industriels majeurs sont principalement, à l’heure actuelle, la conception des structures simplifiées au maximum afin de réduire les coûts de production et la réduction des consommations énergétiques. A cet effet, l’industrie aéronautique fait fréquemment appel à l’assemblage par collage en raison de nombreux avantages qu’il offre (gain de poids, distribution régulière des contraintes, absence de trous) par rapport aux autres techniques existantes. Le PEEK (PolyEtherEtherKetone), est un matériau polymère semi-cristallin thermoplastique, à hautes performances. Ce matériau est souvent utilise dans l’industrie aéronautique principalement renforce par des fibres de carbone ou de verre. Cependant, du fait du niveau élevé de sa résistance chimique l’assemblage par collage du PEEK et de ses composites nécessitent des traitements de surfaces appropries et optimises. Or, afin d’obtenir un system collé à haute performance, la problématique scientifique et technique doit être concentrée sur la jonction entre les éléments à assembler. En effet, la qualité de cette jonction est de la plus haute importance car elle doit permettre un transfert optimal des contraintes thermomécaniques lorsque l’assemblage est soumis a ses conditions d'usage. Cette étude concerne donc, l’amélioration des propriétés mécaniques (monotones et cycliques) de l’assemblage par collage PEEK/PEEK. Dans cette optique, un traitement de surface simple de mise en œuvre est proposé. Ce traitement est le sablage, qui permet la modification topographique (morphologique) de surface. La compréhension des différents phénomènes d’interaction aux interfaces intervenant dans l’amélioration du comportement mécanique du joint de colle et qui s’inscrit dans la triptyque : « Rhéologie, Physico-chimie et topographie », est l’enjeu scientifique majeur dans cette thèse. Dans un premier temps, l’influence des paramètres du traitement tels que le temps de projection, la taille des particules, sur la morphologie de surface de différents matériaux à base de PEEK a été analysée, permettant ainsi d’établir la corrélation entre les paramètres morphologiques et les mécanismes de modification topographique de surface intervenant pendant le traitement de surface. L’un des facteurs clefs pour la compréhension des mécanismes d’interaction entre l’adhésif liquide et le substrat solide est la mouillabilité. L’analyse du comportement au mouillage en fonction des différents paramètres du traitement a été réalisée. La mouillabilité des surfaces traitées est fortement affectée par la rugosité de surface créée après ce traitement. La relation entre les paramètres morphologiques et la mouillabilité a été discutée. Enfin, l’influence des paramètres du traitement par sablage sur le comportement mécanique monotone et à long terme (essais de fatigue) sur la résistance du joint colle a été étudié à l’aide d’essais de cisaillement sur éprouvettes à simple recouvrement. Ceci a conduit, à la proposition de paramètres morphologiques surfaciques spécifiques pour l’optimisation du comportement mécanique du joint de colle des matériaux composites à matrice PEEK. / One of most problematic in the aeronautical industries is the structural joining of the high performance thermoplastic composites like PEEK composites. Actually, a lot of technologies are used for joining thermoplastic composites like welding, bolting, riveting, fastening and adhesive bonding. Due to the various advantages that characterize the adhesive bonding method, such an uniform stress distribution along the joint, weight‐light and cost reduction, makes this technique more desirable to join thermoplastic composites materials compared to the other joining techniques. PEEK (PolyEtherEtherKetone) is a semi‐crystalline thermoplastic material with high performance. This material is wildly used in aeronautical industries, principally, reinforced with carbon of glass fibres. However, its high chemical resistance makes the adhesive bonding of PEEK and its composites difficult and therefore an appropriate and optimised surface treatment is necessary. In the aim to obtain a bonded system with high performance, scientific and technical problematic should be focussed on the junction between adherents. Indeed, the quality of this junction is of utmost importance because it must allow optimum transfer of thermomechanical stresses when the assembly is subject to its terms of use. Though, at this time it is well known that thermoplastic composite materials are difficult to bond with‐out surface treatment. This study, therefore, relates to the improvement of mechanical properties (monotonic and cyclic) of the adhesive bonding system PEEK / PEEK. In this context, a surface treatment, easy to implement, is proposed. This surface treatment is sandblasting, which enables surface topographic (morphological) modifications. Understanding of various phenomena of interfaces interaction involved in the improvement of the mechanical behavior of the adhesive joint and is part of the triptych "Rheology, Physico‐chemistry and topography" is the major scientific challenge in this thesis. Initially, the influence of processing parameters such as the projection time, the particle size on surface morphology of various materials based on PEEK was analysed, thus allowing establishing the correlation between morphological parameters and modification mechanisms involved during surface treatment surface. One of the key factors for understanding the mechanisms of interaction between the liquid adhesive and the solid substrate is wettability. The analysis of the wetting behavior as a function of various parameters of the treatment was performed. The wettability of treated surfaces is strongly affected by surface roughness created after this treatment. The relationship between morphological parameters and wettability was discussed. Finally, the influence of sandblasting processing parameters on the mechanical behavior in monotoning and long‐term (fatigue tests) of the adhesive joint strength was studied, using single lap shear tests specimens. This has led to the proposal of specific surface morphological parameters for the optimization of the mechanical behavior of the adhesive joint of PEEK and its composites.

This thesis presents methods for the wafer-level integration of shape memory alloy (SMA) and electrostatic actuators to functionalize MEMS devices. The integration methods are based on heterogeneous integration, which is the integration of different materials and technologies. Background information about the actuators and the integration method is provided. SMA microactuators offer the highest work density of all MEMS actuators, however, they are not yet a standard MEMS material, partially due to the lack of proper wafer-level integration methods. This thesis presents methods for the wafer-level heterogeneous integration of bulk SMA sheets and wires with silicon microstructures. First concepts and experiments are presented for integrating SMA actuators with knife gate microvalves, which are introduced in this thesis. These microvalves feature a gate moving out-of-plane to regulate a gas flow and first measurements indicate outstanding pneumatic performance in relation to the consumed silicon footprint area. This part of the work also includes a novel technique for the footprint and thickness independent selective release of Au-Si eutectically bonded microstructures based on localized electrochemical etching. Electrostatic actuators are presented to functionalize MEMS crossbar switches, which are intended for the automated reconfiguration of copper-wire telecommunication networks and must allow to interconnect a number of input lines to a number of output lines in any combination desired. Following the concepts of heterogeneous integration, the device is divided into two parts which are fabricated separately and then assembled. One part contains an array of double-pole single-throw S-shaped actuator MEMS switches. The other part contains a signal line routing network which is interconnected by the switches after assembly of the two parts. The assembly is based on patterned adhesive wafer bonding and results in wafer-level encapsulation of the switch array. During operation, the switches in these arrays must be individually addressable. Instead of controlling each element with individual control lines, this thesis investigates a row/column addressing scheme to individually pull in or pull out single electrostatic actuators in the array with maximum operational reliability, determined by the statistical parameters of the pull-in and pull-out characteristics of the actuators. / QC20100729

Die Filtration unter aggressiven Einsatzbedingungen, z.B. Einsatz in korrosiven Medien, Abgasfiltration, stellt besondere Anforderungen an das Filtermaterial. Sogenanntes "Liquid Phase Sintered Silicon Carbide" (LPS-SiC) erfüllt die Anforderungen sehr gut. Deshalb bestand das Ziel der Arbeit besteht darin, erstmals aus LPS-SiC asymmetrische keramische Membranen (grobporöses Substrat mit dünner, feinporiger Membran) herzustellen. Als Additivsystem fanden Yttriumoxid und Aluminiumoxid Verwendung. Es wurde Siliciumcarbid der Körnung F1200 auf Substrat der Körnung F500 abgeschieden. Dem Herstellungsverfahren kommt für die Qualität der Membran eine große Bedeutung zu. Daher wurden in dieser Arbeit folgende Beschichtungsmethoden untersucht, um die optimale Methode zu identifizieren: Tauchbeschichtung, elektrophoretische Abscheidung, Druckfiltration und Einsatz von Transfertapes (Transfertapes: Mischung aus Polyacrylatkleber und Pulver). Im Mittelpunkt stand dabei die Druckfiltration. Hierfür wurde eine neue Apparatur konzipiert und aufgebaut. Für die schlickerbasierten Methoden wurde ein wässriges System entwickelt, bei dem auf den Einsatz von organischen Hilfsstoffen verzichtet werden konnte. Die elektrostatische Stabilisierung konnte durch gezieltes Anlösen von Yttriumoxid, Ausfällen von feinskaligem Yttriumhydroxid und Belegung des Siliciumcarbids mit dem Yttriumhydroxid erreicht werden. Die Elektrophorese führte zu keinen befriedigenden Ergebnissen aufgrund des undefinierten spezifischen Widerstandes des Substrats (siehe Dissertation Jan Ihle, Bergakademie Freiberg 2004). Die Druckfiltration erwies sich als das geeignetste Verfahren. Mit ihr konnten ohne Einschränkungen hochwertige Membranen erzeugt werden. Druck und Zeit sind bei gegebenen Feststoffgehalt frei wählbar. Der Druck wurde zwischen 2*10E4 und 1*10E5 Pa variiert. Höherer Druck führte zu feineren Porengrößen (mittlere und maximale Porengröße). Mit der Druckfiltration konnten Membranen ohne makroskopische Defekte erzeugt werden. Sie führte im Vergleich aller Verfahren zu der geringsten Rauhtiefe der Membranen. Die Tauchbeschichtung ließ sich in diesem System nur über den Feststoffgehalt steuern. Membranen aus der Tauchbeschichtung wiesen makroskopische Fehler (große oberflächliche Poren) auf. Die Methode führte hinsichtlich Porengrößen und Rauhtiefe zu den schlechtesten Werten. Die Transfertape-Methode als neuartiger Ansatz erwies sich für das LPS-SiC System als noch nicht ausgereift. Das direkte Bekleben der Substrate war möglich. Hinsichtlich der Membrandicke sind aber Grenzen bei ca. 50 µm gesetzt. Darüber hinaus reißen die Membranen. Es wurden Schwankungen in der Entbinder- und Sinterschwindung verzeichnet. Weiterhin werden große Hohlräume im Substrat nicht von den Transfertapes abgeformt. Beide Effekte erhöhen die Spannungen beim Sintern, so dass bei geringeren Schichtdicken Risse entstehen. / Silicon Carbide (SiC) fulfills many requirements, e.g. a high robustness in terms of corrosion, which makes it a suitable Material for ceramic membranes. The aim of this work was to produce ceramic membranes out of porous liquid phase sintered Silicon Carbide (LPS-SiC). As additives Alumina and Yttria were used. The SiC based on commercial abrasive powders F1200 (Membrane) and F500 (Substrate). Different techniques of membrane formation were applied in order to find the optimum processing procedure: Dip Coating, Electrophoretic Deposition (EPD), Pressure Filtration and the usage of so called Transfer Tapes, a blend of Polyacrylate and ceramic powders). For the slip based methods a water based system was developed without the need of organic additives. A pure electrostatic stabilization was facilitated by solving Yttria with Hydrochloride Acid and precipitation, resulting in the coverage of the SiC particles with finely dispersed Yttria. The EPD was not successful due to a undefined specific resistance of the substrate. The pressure filtration turned out to be the best, most versatile method, leading to defect free membranes with the lowest measured surface roughness. The pressure ranged between 2*10E4 and 1*10E5 Pa. Higher pressure lead to finer pores. The Dip Coating was controlled only by the solids content. Membranes by Dip Coating showed macroscopic defects. As a new concept for ceramic membrane fabrication the Transfer Tapes needed further investigation. The direct gluing on the substrate was possible. The thickness of the membrane was limited to 50 microns in order to keep free of cracks. The Transfer Tapes exhibited pronounced fluctuations in the debinding and sintering shrinkage, leading to increased tension during sintering. Furthermore cavities, (e.g. big pores) were bridged. Both effects lead to increased tension during sintering.

Der derzeitige technische Fortschritt stützt sich maßgeblich auf die Nutzung von elektrischem Strom. Der Anteil der Stromerzeugung aus Sonnenlicht hat mittlerweile in Deutschland den der Wasserkraft überschritten, der 1990 noch der größte regenerative Energielieferant war. Die Technologie der Photovoltaik (PV) wandelt die hochenergetische Strahlung der Sonne in elektrischen Strom um und nutzt dabei häufig Glasplatten als tragende Struktur. Der Hauptanspruch dieser Arbeit liegt in der Entwicklung und Untersuchung eines Befestigungssystems mit einer höher- oder hochmoduligen Klebverbindung zum gläsernen PV-Modul sowie einer möglichst universell einsetzbaren Fügeverbindung zur Unterkonstrukion. Die systematische Enwicklung der Fügeverbindung zum PV-Modul basiert auf dem Ansatz eines flexiblen, stützenden \\hbox{Ringes} für das Fügeelement (Halter), um die durch eine mechanische Belastung der Module induzierten Zugspannungen im Glas über der Fügeelementkante zu reduzieren. Eine neuartige, kombinierte Klammer-Keil-Verbindung sichert die Befestigung auf einer von ihr unabhängigen Unterkonstruktion sowohl quer als auch längs zur Schienenrichtung. Experimentelle Arbeiten charakterisieren die eingesetzte Klebverbindung unter verschiedenen Beanspruchungsszenarien, um sowohl konstruktions- als auch klebstoffbedingte Möglichkeiten und Grenzen der Fügeverbindung für die vorliegende Anwendung zu identifizieren. Die Untersuchungen weisen zudem geeignete Vorbehandlungsmaßnahmen der Aluminiumoberflächen aus. Sowohl numerische Simulationen als auch die neuartig eingesetzte Nahbereichsphotogrammetrie bestätigen in Bauteiluntersuchungen die vorteilige Wirkung des flexiblen, höhermodulig geklebten Ringes. Die vorliegende Arbeit setzt sich hierbei auch kritisch mit unterschiedlichen Einflüssen auf die Ergebnisse auseinander, die einerseits durch verschiedene Prüfstände hervorgerufen werden können und andererseits auch den verwendeten Methoden zugrunde liegen. / Today much of technical advances are due to the usage of electricity. The contribution of solar power to the production of electricity in Germany currently surpasses water powered electricity which was in 1990 the almost exclusive renewable energy source. The technology of photovoltaic systems based on high-powered sun radiation, often utilizes glass plates as a supporting structure. This dissertation primarily focuses on the research and development of a mounting system with a higher or high modulus adhesively bonded joint to the PV-module as well as an all-purpose connection to the substructure. The systematical development process of the connection to the PV-module is based on the approach of a flexible supporting ring-shaped mounting element. This reduces the tension within the glass surface at the edge of the mounting element when mechanically loading the PV-module. A novel connection using a clamp-wedge combination ensures the ability to mount the PV-module horizontally or vertically to the rail substructure. Through the development process, the bonded joint is exposed to various scenarios where the construction as well as the adhesive possibilities and limitations under each scenario are analyzed. Research outcomes yield recommendations for appropriate pre-treatment of the aluminum surfaces. Numerical simulations as well as the novel use of the near-field photogrammetry method confirmed beneficial action of the flexible ring-shaped mounting element within assembly testing of large glass specimens. This dissertation discusses how different variables can have a considerable effect on results when introduced through the testing device and through monitoring methods.

Der derzeitige technische Fortschritt stützt sich maßgeblich auf die Nutzung von elektrischem Strom. Der Anteil der Stromerzeugung aus Sonnenlicht hat mittlerweile in Deutschland den der Wasserkraft überschritten, der 1990 noch der größte regenerative Energielieferant war. Die Technologie der Photovoltaik (PV) wandelt die hochenergetische Strahlung der Sonne in elektrischen Strom um und nutzt dabei häufig Glasplatten als tragende Struktur. Der Hauptanspruch dieser Arbeit liegt in der Entwicklung und Untersuchung eines Befestigungssystems mit einer höher- oder hochmoduligen Klebverbindung zum gläsernen PV-Modul sowie einer möglichst universell einsetzbaren Fügeverbindung zur Unterkonstrukion. Die systematische Enwicklung der Fügeverbindung zum PV-Modul basiert auf dem Ansatz eines flexiblen, stützenden \\hbox{Ringes} für das Fügeelement (Halter), um die durch eine mechanische Belastung der Module induzierten Zugspannungen im Glas über der Fügeelementkante zu reduzieren. Eine neuartige, kombinierte Klammer-Keil-Verbindung sichert die Befestigung auf einer von ihr unabhängigen Unterkonstruktion sowohl quer als auch längs zur Schienenrichtung. Experimentelle Arbeiten charakterisieren die eingesetzte Klebverbindung unter verschiedenen Beanspruchungsszenarien, um sowohl konstruktions- als auch klebstoffbedingte Möglichkeiten und Grenzen der Fügeverbindung für die vorliegende Anwendung zu identifizieren. Die Untersuchungen weisen zudem geeignete Vorbehandlungsmaßnahmen der Aluminiumoberflächen aus. Sowohl numerische Simulationen als auch die neuartig eingesetzte Nahbereichsphotogrammetrie bestätigen in Bauteiluntersuchungen die vorteilige Wirkung des flexiblen, höhermodulig geklebten Ringes. Die vorliegende Arbeit setzt sich hierbei auch kritisch mit unterschiedlichen Einflüssen auf die Ergebnisse auseinander, die einerseits durch verschiedene Prüfstände hervorgerufen werden können und andererseits auch den verwendeten Methoden zugrunde liegen. / Today much of technical advances are due to the usage of electricity. The contribution of solar power to the production of electricity in Germany currently surpasses water powered electricity which was in 1990 the almost exclusive renewable energy source. The technology of photovoltaic systems based on high-powered sun radiation, often utilizes glass plates as a supporting structure. This dissertation primarily focuses on the research and development of a mounting system with a higher or high modulus adhesively bonded joint to the PV-module as well as an all-purpose connection to the substructure. The systematical development process of the connection to the PV-module is based on the approach of a flexible supporting ring-shaped mounting element. This reduces the tension within the glass surface at the edge of the mounting element when mechanically loading the PV-module. A novel connection using a clamp-wedge combination ensures the ability to mount the PV-module horizontally or vertically to the rail substructure. Through the development process, the bonded joint is exposed to various scenarios where the construction as well as the adhesive possibilities and limitations under each scenario are analyzed. Research outcomes yield recommendations for appropriate pre-treatment of the aluminum surfaces. Numerical simulations as well as the novel use of the near-field photogrammetry method confirmed beneficial action of the flexible ring-shaped mounting element within assembly testing of large glass specimens. This dissertation discusses how different variables can have a considerable effect on results when introduced through the testing device and through monitoring methods.

Die Filtration unter aggressiven Einsatzbedingungen, z.B. Einsatz in korrosiven Medien, Abgasfiltration, stellt besondere Anforderungen an das Filtermaterial. Sogenanntes "Liquid Phase Sintered Silicon Carbide" (LPS-SiC) erfüllt die Anforderungen sehr gut. Deshalb bestand das Ziel der Arbeit besteht darin, erstmals aus LPS-SiC asymmetrische keramische Membranen (grobporöses Substrat mit dünner, feinporiger Membran) herzustellen. Als Additivsystem fanden Yttriumoxid und Aluminiumoxid Verwendung. Es wurde Siliciumcarbid der Körnung F1200 auf Substrat der Körnung F500 abgeschieden. Dem Herstellungsverfahren kommt für die Qualität der Membran eine große Bedeutung zu. Daher wurden in dieser Arbeit folgende Beschichtungsmethoden untersucht, um die optimale Methode zu identifizieren: Tauchbeschichtung, elektrophoretische Abscheidung, Druckfiltration und Einsatz von Transfertapes (Transfertapes: Mischung aus Polyacrylatkleber und Pulver). Im Mittelpunkt stand dabei die Druckfiltration. Hierfür wurde eine neue Apparatur konzipiert und aufgebaut. Für die schlickerbasierten Methoden wurde ein wässriges System entwickelt, bei dem auf den Einsatz von organischen Hilfsstoffen verzichtet werden konnte. Die elektrostatische Stabilisierung konnte durch gezieltes Anlösen von Yttriumoxid, Ausfällen von feinskaligem Yttriumhydroxid und Belegung des Siliciumcarbids mit dem Yttriumhydroxid erreicht werden. Die Elektrophorese führte zu keinen befriedigenden Ergebnissen aufgrund des undefinierten spezifischen Widerstandes des Substrats (siehe Dissertation Jan Ihle, Bergakademie Freiberg 2004). Die Druckfiltration erwies sich als das geeignetste Verfahren. Mit ihr konnten ohne Einschränkungen hochwertige Membranen erzeugt werden. Druck und Zeit sind bei gegebenen Feststoffgehalt frei wählbar. Der Druck wurde zwischen 2*10E4 und 1*10E5 Pa variiert. Höherer Druck führte zu feineren Porengrößen (mittlere und maximale Porengröße). Mit der Druckfiltration konnten Membranen ohne makroskopische Defekte erzeugt werden. Sie führte im Vergleich aller Verfahren zu der geringsten Rauhtiefe der Membranen. Die Tauchbeschichtung ließ sich in diesem System nur über den Feststoffgehalt steuern. Membranen aus der Tauchbeschichtung wiesen makroskopische Fehler (große oberflächliche Poren) auf. Die Methode führte hinsichtlich Porengrößen und Rauhtiefe zu den schlechtesten Werten. Die Transfertape-Methode als neuartiger Ansatz erwies sich für das LPS-SiC System als noch nicht ausgereift. Das direkte Bekleben der Substrate war möglich. Hinsichtlich der Membrandicke sind aber Grenzen bei ca. 50 µm gesetzt. Darüber hinaus reißen die Membranen. Es wurden Schwankungen in der Entbinder- und Sinterschwindung verzeichnet. Weiterhin werden große Hohlräume im Substrat nicht von den Transfertapes abgeformt. Beide Effekte erhöhen die Spannungen beim Sintern, so dass bei geringeren Schichtdicken Risse entstehen. / Silicon Carbide (SiC) fulfills many requirements, e.g. a high robustness in terms of corrosion, which makes it a suitable Material for ceramic membranes. The aim of this work was to produce ceramic membranes out of porous liquid phase sintered Silicon Carbide (LPS-SiC). As additives Alumina and Yttria were used. The SiC based on commercial abrasive powders F1200 (Membrane) and F500 (Substrate). Different techniques of membrane formation were applied in order to find the optimum processing procedure: Dip Coating, Electrophoretic Deposition (EPD), Pressure Filtration and the usage of so called Transfer Tapes, a blend of Polyacrylate and ceramic powders). For the slip based methods a water based system was developed without the need of organic additives. A pure electrostatic stabilization was facilitated by solving Yttria with Hydrochloride Acid and precipitation, resulting in the coverage of the SiC particles with finely dispersed Yttria. The EPD was not successful due to a undefined specific resistance of the substrate. The pressure filtration turned out to be the best, most versatile method, leading to defect free membranes with the lowest measured surface roughness. The pressure ranged between 2*10E4 and 1*10E5 Pa. Higher pressure lead to finer pores. The Dip Coating was controlled only by the solids content. Membranes by Dip Coating showed macroscopic defects. As a new concept for ceramic membrane fabrication the Transfer Tapes needed further investigation. The direct gluing on the substrate was possible. The thickness of the membrane was limited to 50 microns in order to keep free of cracks. The Transfer Tapes exhibited pronounced fluctuations in the debinding and sintering shrinkage, leading to increased tension during sintering. Furthermore cavities, (e.g. big pores) were bridged. Both effects lead to increased tension during sintering.

Adhesive bonding which has been in use for long as a traditional joining method has gained ground in the last couple of decades due to the introduction of advanced composite materials into the aerospace industry. Bonded structures have advantages such as high corrosion and fatigue resistance, ability to join dissimilar materials, reduced stress concentration, uniform stress distribution, good damping characteristics etc. They also have certain limitations like environmental degradation, existence of defects like pores, voids and disbonds, difficulty in maintenance and repair etc. A serious drawback in the use of adhesively bonded structures has been that there are no established comprehensive non-destructive testing (NDT) techniques for their evaluation. Further, a reliable evaluation of the effect of the existing defects on strength and durability of adhesive joints is yet to be achieved. This has been a challenge for the research and development community over several decades and hence, been the motivation behind this piece of research work. Under the scope of the work carried out in the thesis, some of the primary factors such as the existence of defects, degradation of the adhesive, stress and strain distribution in the bonded region etc., have been considered to study the bond integrity in composite to composite lap shear joints. The problem becomes complex if all the parameters affecting the adhesive joint are varied simultaneously. Taking this into consideration, one of the key parameters affecting the bond quality, viz., the adhesive layer degradation was chosen to study its effect on the bonded joint. The epoxy layer was added with different, definite amount of Poly vinyl alcohol (PVA) to arrive at sets of bonded joint specimens with varied adhesive layer properties. A thorough review of different non destructive testing methods applied to this particular problem showed that ultrasonic wave based techniques could be the right choice. To start with, preliminary experimental investigations were carried on unidirectional glass fiber reinforced plastic (GFRP-epoxy) lap joints. The adhesive joints were subjected to non destructive evaluation (NDE) using ultrasonic through transmission and pulse echo techniques as also low energy digital X-ray techniques. The results obtained showed a variation in reflected and transmitted ultrasonic pulse amplitude with bond quality. Digital X-Ray radiography technique showed a variation in the intensity of transmitted x-rays due to variation in the density of adhesive. Standard mechanical tests revealed that the addition of PVA decreased the bond strength. A plot of coefficient of reflection from the first interface and the bond strength showed a linear correlation between them. After obtaining a cursory feel and understanding of the parameters involved with the preliminary experiments on GFRP adhesive joints which yielded interesting and encouraging results, further work was carried on specimens made out of autoclave cured carbon fiber reinforced plastic (CFRP)-epoxy bonded joints. Normal incidence ultrasound showed a similar trend. Analyses of the Acoustic Emission (AE) signals generated indicate early AE activity for degraded joints compared to healthy joints. Literary evidences suggest that the ultrasonic shear waves are more sensitive to interfacial degradation. An attempt was made to use oblique incidence ultrasonic interrogation using shear waves. The amplitude of reflected shear waves from the interface increased with an increase in degradation. Further, a signal analysis approach in the frequency domain revealed a shift in the frequency minimum towards lower range in degraded samples. This phenomenon was verified using analytical models. An inversion algorithm was used to determine the interfacial transverse stiffness which decreased significantly due to increase in degradation. Conventional ultrasonic evaluation methods are rendered ineffective when a direct access to the test region is not possible; a different approach with guided wave techniques can be explored in this scenario. Investigations on CFRP-epoxy adhesive joints using Lamb waves showed a decrease in the amplitude of ‘So’ mode in degraded samples. Theoretical dispersion curves exhibited a similar trend. Frequency domain studies on the received modes using Gabor wavelet transform showed a negative shift in frequency with increased degradation. It was also observed that the maximum transmission loss for the most degraded sample with 40 percent PVA occurred in the range of 650 – 800 kHz. Non linear ultrasonic (NLU) evaluation revealed that the nonlinearity parameter (β) increased with increased degradation. Kissing bonds are most commonly occurring type of defects in adhesive joints and are very difficult to characterize. A recent non-contact imaging technique called digital image correlation (DIC) was tried to evaluate composite adhesive joints with varied percentage of inserted kissing bond defects. The results obtained indicate that DIC can detect the kissing bonds even at 50 percent of the failure load. In addition, to different experimental approaches to evaluate the bonded joint discussed above, the effect of degradation on the stresses in the bond line region was studied using analytical and numerical approach. A linear adhesive beam model based on Euler beam theory and a nonlinear adhesive beam model based on Timoshenko beam theory were used to determine the adhesive peel and shear stress in the joint. Digital image correlation technique was used to experimentally obtain the bond line strains and corresponding stresses were computed assuming a plane strain condition. It was found that the experimental stresses followed a similar trend to that predicted by the two analytical models. A maximum peel stress failure criterion was used to predict failure loads. A failure mechanism was proposed based on the observations made during the experimental work. It was further shown that the critical strain energy release rate for crack initiation in a healthy joint is much higher compared to a degraded joint. The analytical models become cumbersome if a larger number of factors have to be taken into account. Numerical methods like finite element analysis are found to be promising in overcoming these hurdles. Numerical investigation using 3D finite element analysis was carried out on CFRP-epoxy adhesive joints. The adherend – adhesive interface was modeled using connector elements whose stiffness properties as well as the bulk adhesive properties for joints with different amounts of PVA were determined using ultrasonic inspection method. The peel and shear stress variation along the adhesive bond line showed a similar trend as observed with the experimental stress distribution (DIC) but with a lesser magnitude. A parametric study using finite element based Monte-Carlo simulation was carried out to assess the effect of variation in various joint parameters like adhesive modulus, bondline thickness, adherend geometrical and material properties on peel and shear stress in the joint. It was found that the adhesive modulus and bond line thickness had a significant influence on the magnitude of stresses developed in the bond line. Thus, to summarize, an attempt has been made to study the bond line integrity of a composite epoxy adhesive lap joint using experimental, analytical and numerical approaches. Advanced NDE tools like oblique incidence ultrasound, non linear ultrasound, Lamb wave inspection and digital image correlation have been used to extract parameters which can be used to evaluate composite bonded joints. The results obtained and reported in the thesis have been encouraging and indicate that in specific cases where the bond line thickness and other relevant parameters if can be maintained or presumed reasonably non variant, it is possible to effectively evaluate the integrity of a composite bonded joint.