Rational harmonic mode-locking (RHML) fiber lasers generating picoseconds pulsewidth at high-repetition-rate have emerged as a key component for the high-bit-rate optical time-division multiplexing (OTDM) communication system. In this research, we have discovered higher order RHML semiconductor optical amplifier fiber laser (SOAFL) has the degradation on mode-locking capacity, and an output pulse-train with un-equalized peak amplitudes. Therefore, the main focus of the dissertation is focused on the pulse quality analysis and improvement of RHML-SOAFL via optical pulse injection. First, we observed the degradation on mode-locked mechanism of the dark-optical-comb injection mode-locked semiconductor optical amplifier fiber laser (SOAFL) at RHML order increases to >8. Such a less pronounced RHML mechanism at higher orders is mainly attributed to the weak mode-locking strength at high RHML orders as compared to continuous-wave (CW) lasing mechanism, which has been quantified by reduction of spectral linewidth and pulse-shortening force, and the ratio of DC/pulse amplitude enhancement for discriminating 1st to 20th-order RHML capability. To overcome the un-equalized RHML peak intensity, optical injection induced gain modulation of a SOA are demonstrated to equalize the peak intensity of 5-GHz and 40-GHz RHML-SOAFL by using 1-GHz inverse-optical-pulse and a reshaped 10-GHz gain-switching FPLD pulse injection, respectively. The optical injection mode-locking models are constructed to simulate the compensation of uneven amplitudes between adjacent RHML pulse peaks before and after pulse-amplitude equalization. The optimized RHML pulse exhibits a signal-to-noise suppression ratio of 45-dB, and the clock amplitude jitter below the threshold limitation of 10%. On the other hand, to avoid the mode-locked degradation on RHML, a 2nd-order fractional Talbot effect induced frequency-doubling of 10-GHz optical pulse-train is demonstrated to backward inject a SOAFL for 40-GHz RHML. In comparison with the SOAFL pulse-train repeated at 40-GHz generated by the 4th-order purely RHML process, the optimized 2nd-order fractional Talbot effect in combination with the 2nd-order RHML mechanism significantly enhances the modulation-depth of RHML, thus improving the on/off extinction ratio of the 40-GHz SOAFL pulse-train. Such a new scheme also provides a more stable 40-GHz RHML pulse-train from the SOAFL with its timing jitter reduce. Finally, we established a SHG-FROG to distinguish linear and nonlinear chirp of 10-GHz soliton HML-SOAFL, and further extracted intra-cavity linear dispersion via simulation of Schrodinger equation. After the procedure, the linear chirp almost dominates chirp characteristics for optical pulse injection HML-SOAFL system.

Initialement poussées par le marché résidentiel, les évolutions du réseau d’accès optique sont aujourd’hui également stimulées par l’expansion du réseau mobile. Comme le montre le premier chapitre de ce document, l’introduction d’un multiplexage en longueur d’onde dense constitue l’une des solutions privilégiées pour permettre la montée en débit dans les réseaux d’accès optique. Dans cette thèse, l’impact de l’introduction du multiplexage en longueur d’onde dense est étudié sous trois axes :• Une prochaine étape de l’évolution des technologies pour les réseaux d’accès passerait par une hybridation entre d’une part, un multiplexage temporel (hérité des précédentes générations), et d’autre part, un multiplexage en longueur d’onde dense. Cette technologie, appelée NGPON2-TWDM, permet aujourd’hui d’envisager des débits de 40Gb/s à 80Gb/s grâce à 4 ou 8 canaux. Les difficultés liées à la stabilité de la longueur d’onde lors de l’émission de données en mode paquet dans le sens montant du lien, ainsi que les solutions associées, sont étudiées dans le second chapitre.• L’importance du marché que représente le réseau d’accès optique (aussi bien pour les clients résidentiels que pour les réseaux mobiles), induit la nécessité pour les différentes générations de technologies de coexister au sein d’une même infrastructure. Du fait des fortes puissances optiques en jeu et des plages spectrales allouées à chaque technologie, cette coexistence peut induire des interactions entre technologies par émission Raman stimulée, dont le principe et les impacts sont décrits dans le troisième chapitre.• Enfin, la quatrième partie de ce document est dédiée à l’étude des limites et potentialités de la technologie self-seeded pour le multiplexage en longueur d’onde dense en bande O, capable de stabiliser automatiquement et passivement la longueur d’onde d’émission de chacun des émetteurs du système. / Initially led by the residential market, today’s optical access network evolutions are stimulated by mobile network expansion. As shown in the first chapter of this document, dense wavelength division multiplexing is one of the favorite solutions in order to increase optical access networks throughput. In this thesis, we propose a study of dense wavelength division multiplexing introduction according to three main topics :• Service providers and equipment suppliers have decided that the next step in residential market evolution will consist in a hybridization between, on one hand, a legacy time division multiplexing, and on the other hand, a dense wavelength division multiplexing. Named NG-PON2, this technology allows today 40Gb/s to 80Gb/s thanks to 4 to 8 channel pairs. Wavelength stability of the upstream emitter under burst mode operation, and related solutions, are studied in the second chapter.• Market importance (for both residential market and mobile networks) requires the different technologies generations to coexist on the same infrastructure. Due to the high optical power and the wavelength spans allocated to each technology, this coexistence can lead to technologies interactions by stimulated Raman scattering, as described in the third chapter.• Finally, the fourth part of this document describes the limits and potentialities of the self-seeded emitter technology for O-band dense wavelength division multiplexing, able to automatically and passively self-stabilize the wavelength of each emitter.

No description available.

No description available.

We clear up two issues regarding the eigenvalue problem for the Manakov system; these problems relate directly to the existence of the soliton [sic] effect in fiber optic cables. The first issue is a bound on the eigenvalues of the Manakov system: if the parameter ξ is an eigenvalue, then it must lie in a certain region in the complex plane. The second issue has to do with a chirped Manakov system. We show that if a system is chirped too much, the soliton effect disappears. While this has been known for some time experimentally, there has not yet been a theoretical result along these lines for the Manakov system. / Ph. D.

This thesis is concerned with various methods for the control and investigation of pulse dynamics in a Photonic Crystal Fibre (PCF) and of the radiation driven by a short pulse. In particular the focus is on pulses in the anomalous dispersion region which would form solitons in the absence of higher order effects. Several different types of radiation can be driven by such pulses if they are perturbed by higher order dispersive and non-linear effects - for example Resonant Radiation (RR) and Negative Resonant Radiation (NRR) two dispersive waves which gain energy at the expense of the pulse. The feature of NRR which is of particular importance is that it is the first observed example of a coupling between positive and negative frequencies in optics. This has only been possible due to recent advances in fields such as PCFs, lasers and analogue systems. As with many scientific discoveries, NRR was found by bringing together ideas and techniques from these different fields. Both the pulse and the driven radiation are investigated using a number of different pulse and PCF parameters. These include power, chirp, polarisation and PCF dispersion. These are used to vary the wavelengths at which the driven radiation occurs as well as its generation efficiency. Furthermore the power and chirp are used to vary where in the PCF the driven radiation is generated by controlling where the driving pulse compresses and spectrally expands. This property is used to investigate different stages in the evolution of the pulse and driven radiation as well as to optimise the generation efficiency of the driven radiation.

Radars have been under steady development to track, identify, image, and classify targets. Modern radar systems, with the help of embedded systems, have additional comprehensive signal processing capabilities. They can extract useful information from very noisy data, e.g. interference from the environment and unwanted echoes which is collectively known as clutter in radar terms. Concerning the healthcare industry, radar applications for detection of vital signs, i.e. breathing and heart rate, have been extensively developed during the last few decades. Modern radar systems are expected to be a large part of non-intrusive monitoring in the coming smart home industry, where vital signs need to be monitored in the currently aging population. The research presented here is to break new ground in the radar-based healthcare technology, enabling detection of cold-induced shivering to such level that the micro-shivering can be clearly identified. To simplify the radar software optimization, a commercially available radar kit with demo application and a muscle model system using a vibration generator is used. The model is quantified through precise measurements. A simulated human body vital sign plus shivering is applied. By optimizing the radar software, the shivering amplitude and frequency are measured.

Les lasers à électrons libres (LELs) à simple passage représentent actuellement la possibilité la plus prometteuse pour fournir des impulsions lumineuses de haute énergie (µJ à mJ) à des échelles de durée femtoseconde (1 fs = 10⁻¹⁵s) et des longueurs d'ondes ultra-courtes (résolution nanométrique i.e., jusqu'aux domaines de l'extrême-ultraviolet et des rayons X). Les LELs émettant dans l'extrême-ultraviolet sont une technologie encore jeune, si bien que de nombreuses questions restent ouvertes. Celles posées au sein de ce manuscrit concernent la configuration dite injectée, dans laquelle le processus est initié par une source externe cohérente (le "seed"). Nous nous concentrons particulièrement dans cette thèse sur les caractéristiques transverses et longitudinales de la lumière, sa cohérence, les propriétés de la phase temporelle et les liens directs entre le seed et l'émission LEL. La technique de génération dans un gaz noble d'harmoniques d'ordres élevés d'un laser femtoseconde (GHE) se montre à la fois complémentaire et en compétition avec les LELs. En compétition car les impulsions produites ont des qualités similaires à celles obtenues avec un LEL ; complémentaire car le rayonnement GHE peut être utilisé comme seed ou en combinaison avec la lumière LEL, par exemple pour effectuer des expériences mettant en jeu de multiples faisceaux. Bien que la GHE fournisse des impulsions moins puissantes, l'implémentation d'une telle source requiert un effort significativement moins important. Le taux de conversion harmonique, l'accordabilité et la qualité spatiale du faisceau généré, et la manière dont ces paramètres dépendent du laser générateur sont les problématiques traitées au sein de ce manuscrit. La volonté de la communauté scientifique d'effectuer des expériences novatrices demande des études profondes et l'optimisation des sources de GHE et des LELs. En particulier, sur la source LEL injectée FERMI@Elettra de Trieste, l'induction d'une dérive de fréquence dans le rayonnement a conduit à des résultats marquants. Entre autres, une méthode de génération d'impulsions scindées avec différentes longueurs d'ondes a été analysée et développée. Une telle possibilité ouvre la voie à l'utilisation des LELs injectés en tant que source autonome pour des installations de type pompe-sonde à deux couleurs. Plus généralement, l'étude des phénomènes mis en jeu dans les processus de GHE et du LEL ainsi que la caractérisation des propriétés de leur lumière sont des sujets intrinsèquement excitants, ayant des connexions directes avec de nombreux aspects fondamentaux de la physique.

Les marges continentales, passives ou actives, sont la principale voie de transfert sédimentaire entre le plateau continental et le bassin océanique profond et les plaines abyssales. Les pentes continentales sont le siège de processus d'érosion/dépôt sous le contrôle de transfert de flux particulaires continentaux chenalisés par des structures érosives, telles que les canyons sous‐marins, puis redistribues à l'ensemble de la marge. Les canyons érodent fortement les pentes continentales et contribuent à l'évolution de leur morphologie au cours du temps. On retrouve cependant des canyons sous‐marins qui ne sont pas en relation avec la présence d'un réseau fluviatile. De ce fait, la formation et l'évolution des canyons sous‐marins sont encore peu comprises. Ce travail de thèse s'intéresse aux processus de formation et d'évolution de six canyons sous-marins sur la Marge Ouest du Bassin Ligure et à dix systèmes de canyons sur la Marge Calabro-Ionienne. Le but de cette étude est de contraindre les principales caractéristiques morphométriques (longueur, largeur, profondeur, inclinaison, sinuosité), morphologique (éléments architecturaux, configuration) des canyons, de caractériser leur évolution amont‐aval et d'analyser leur structure interne, afin de mieux comprendre l'origine des canyons sous‐marins, leurs mécanismes de construction et leur évolution au cours du temps en relation avec le contexte géologique régional et leurs potentiels bassins versants subaérien. Pour cela, une approche basée sur une analyse morpho-bathymétrique et géophysiques a été mise en œuvre à partir de relevés bathymétriques complets des marges, de profils de sismiques, de Chirp et de SAR.

Since their discovery in 1978 by Hill et al. and the development of the transverse holographic technique for their fabrication by Meltz et al. in 1989, fiber Bragg gratings (FBG) have become an important device for applications in optical communications, optical signal processing and fiber-optical sensors. A superstructured fiber Bragg grating (SFBG), also called a sampled fiber Bragg grating, is a special FBG that consists of a several small FBGs placed in close proximity to one another. SFBGs have attracted much attention in recent years with the discovery of techniques allowing the creation of equivalent chirp or equivalent phase shifts. The biggest advantage of an SFBG with equivalent chirp or equivalent phase shifts is the possibility to design and fabricate gratings with greatly varying phase and amplitude responses by adjusting the spatial profile of the superstructure. The realization of SFBGs with equivalent chirp or equivalent phase shifts requires only sub-millimeter precision. This is a relief from the sub-micron precision required by traditional approaches. In this thesis, the mathematical modeling of FBGs and SFBGs is reviewed. The use of SFBGs for various applications in photonic microwave signal processing is considered. Four main topics are presented in this thesis. The first topic is the use of SFBG as a photonic true-time delay (TTD) beamformer for phased array antennas (PAAs). The second topic addresses non-linearities in the group delay response of an SFBG with equivalent chirp in its sampling period. An SFBG with an equivalent chirp using only a linear chirp coefficient may yield a group delay response that deviates from the linear response required by a TTD beamformer. In the thesis, a technique to improve the linearity of the group delay response is proposed and an adaptive algorithm to find the optimal linear and non-linear chirp coefficients to produce the best linear group delay response is described. Since no closed-form solution exists to represent the amplitude and phase responses of an SFBG, we rely on a Fourier transform analogy under a weak grating approximation as a starting point in the design of an SFBG. Simulations are then used to refine the response of the SFBG. The algorithm proposed provides an optimal set of chirp coefficients that minimizes the error in the group delay response. Four gratings are fabricated using the optimized chirp coefficients and their application in a TTD PAA system is discussed. The third topic discusses the use of an SFBG with equivalent phase shifts in its sampling period as a means to realize optical single sideband (SSB) modulation. SSB modulation eliminates the power penalty caused by chromatic dispersion experienced by an optical signal traveling through a long length of optical fiber. By introducing two π phase shifts through equivalent sampling to the SFBG, two ultra-narrow transmission bands are created in the grating stop band of the +/- 1st spectral orders. In the proposed system, a double-sideband plus carrier (DSB+C) modulated optical signal is sent to the input of an optical SSB filter based on the equivalent phase-shift SFBG in order to select the optical carrier and a single sideband, effectively blocking one sideband from propagating. Finally, the fourth topic focuses on the implementation of a photonic microwave bandpass filter based on an SFBG with equivalent chirp. Photonic microwave filters are used to process microwave signals in the optical domain. By using a technique called phase-modulation to intensity-modulation (PM-IM) conversion, a two-tap delay line filter is created with one negative tap. A single SFBG with a chirp in its sampling period is used as a means to achieve the PM-IM conversion for the two taps. Two phase modulated optical carriers are used to generate the two taps, each entering a different port of the SFBG and thus experiencing an opposite dispersion value. The two optical signals are then recombined before being sent to a photodetector (PD) where the filtered microwave signal is recovered.