No description available.

No description available.

This thesis paper supports the Master of Fine Arts exhibition at the Slocumb Galleries, East Tennessee State University, from March 14th through March 18th, 2011. The exhibit is composed of nine oil paintings depicting an invented story about two characters who create a soup for a cooking competition. The show A Matter of Taste chronicles an allegory concerning the evaluation of creative works. Through Gaudie and Baudie's "odd" recipe this work illustrates the ways in artists and art audiences interact and determine artistic value. The work is inspired by techniques in distortion and narrative painting. The following expands on the ideas, influences, techniques, and concepts that helped to create the exhibit.

Serpentine diffusers have become a common feature in modern aircraft as they allow for certain benefits that are impossible with a traditional linear configuration. With the benefits, however, come certain disadvantages, namely flow distortions that reduce engine efficiency and decrease engine surge stability margins. These distortions are now being researched comprehensively to determine solutions for mitigating the adverse effects associated with them. This study investigates how varying the freestream turbulence intensity of the flow entering a serpentine diffuser affects the distortion patterns that are produced by the diffuser. Experiments were performed with a model serpentine diffuser on the Annular Cascade Facility of the Air Force Research Laboratory at Wright-Patterson Air Force Base. Hot wire anemometry was used to measure inlet turbulence, while static pressure probes located axially along the upper and lower surface of the model diffuser and total pressure probes located across the aerodynamic interface plane (AIP) were used to measure the distortion patterns of the flow passing through the diffuser. Varying levels of inlet freestream turbulence, ranging from 0 to 4%, were generated using square and round bar turbulence screens in three distinct test configurations. Axial static pressure measurements indicate that increasing turbulence slightly affects flow separation development downstream of the second turn. This effect is also seen at the AIP where the total pressure recovery increases with increasing level of inlet turbulence in the region of flow separation at the upper surface. The total pressure recovery along the lower surface is also seen to be increased with higher inlet turbulence. However, total pressure recovery increase across the entire AIP is almost negligible. Overall, the inlet freestream turbulence has a minor effect on the distortion patterns caused by the serpentine diffuser when compared with proven active inlet flow control methods.

No description available.

A comprehensive computational and experimental analysis has been conducted to characterize the flow dynamics and periodic structures formed in the wake of complex turning vanes. The vane packs were designed by the StreamVane swirl distortion generator technology, a design system that can efficiently reproduce swirl distortion for compressor rig and full turbofan engine testing. StreamVanes consist of an array of turning vanes that commonly contain variations in turning angle along their span, a nonaxisymmetric profile about the centerline, and vane-to-vane intersections or junctions to accurately generate the desired distortion. In this study, vane packs are considered complex if they contain two out of three of these features, a combination seen in other turbomachinery components outside of StreamVane design. Similar to all stator vanes or rotor blades, StreamVane vane packs are constructed using a series of cross-sectional airfoil profiles with blunt trailing edges and finite thicknesses. This, in turn, introduces periodic vortex structures in the wake, commonly known as trailing edge vortex shedding. To fully understand how the dynamics and coherent wake formations within vortex shedding impact both the flow distortion and structural durability of StreamVanes, it is first necessary to characterize the corresponding wakes in three dimensions. The current study provides an in-depth analysis to predict and measure the trailing edge vortex development using high-fidelity computational fluid dynamics and stereoscopic time-resolved particle image velocimetry experiments. Two testcase StreamVane geometries were specifically designed with complex features to evaluate their influence on the dynamics and coherence of the respective vane wakes. Fully three-dimensional, unsteady computational fluid dynamics simulations were performed using a Reynolds-Averaged Navier-Stokes solver coupled with a standard two-equation turbulence model and a hybrid, scale-resolving turbulence model. Both models predicted large-scale wake frequencies within 1—14% of experiment, with a mean difference of less than 3.2%. These comparisons indicated that lower fidelity simulations were capable of accurately capturing such flows for complex vane packs. Additionally, structural and modal analyses were conducted using finite element models to determine the correlations between dominant structural modes and dominant wake (flow) modes. The simulations predicted that vortex shedding modes generally contained frequencies 300% larger than dominant structural modes, and therefore, vortex induced vibrations were unlikely to occur. Lastly, mode decomposition methods were applied to the experimental results to extract energy ratios and reveal dynamic content across high-order wake modes. The vortex shedding modes generated more than 80% of the total wake energy for both complex vane packs, and dynamic decomposition methods revealed unique structures within the vane junction wake. In all analyses, comparisons were made between different vane parameters, such as trailing edge thickness and turning angle, where it was found that trailing edge thickness was the dominant vortex shedding parameter. The motivation, methodology, and results of the following research is presented to better understand the wake interactions, computational predictive capabilities, and structural dynamics associated with vortex shedding from complex vane packs. Although the results directly relate to StreamVane distortion generator technology, the qualitative and quantitative comparisons between the selected methods, geometry parameters, and flow conditions can be extrapolated to modern turbomachinery components in general. Therefore, this dissertation aims to benefit distortion generator and turbomachinery designers by providing insight into the underlying physics and overall modeling techniques of the wake dynamics in highly three-dimensional, complex components. / Doctor of Philosophy / A comprehensive analysis has been completed to characterize the unsteady wake flow produced by complex turning vane systems in three dimensions. Turning vanes are a common component utilized in the field of fluid dynamics and aerospace propulsion to effectively turn and manipulate the working fluid to the desired condition. For propulsion applications, similar vanes can alleviate performance losses by improving the overall aerodynamics and mitigating flow distortions entering the compressor of a jet engine. Conversely, complex turning vanes can also be used to reproduce the distortion for engineers to evaluate jet engine components when subjected to nonuniform flow ingestion. The distinct geometry features that make these vanes complex are also present in other turbomachinery systems outside of distortion generation. In any case, the cross-sectional profiles of the turning vanes commonly contain blunt ends or trailing edges due to engineering limitations and/or restrictions. This geometric feature introduces periodic wake structures, known as vortex shedding, that can negatively effect the performance of the overall system. It is therefore a necessity to characterize both the dynamics and coherence of vortex shedding to fully understand the flow features in highly three-dimensional flows. In the presented research, this is achieved by applying computational simulations and experimental measurements to extract the corresponding wake dynamics of complex vane packs. The selected testcases where designed using the StreamVane technology, a mature system that generates tailored turning vanes to reproduce flow distortion in jet engine or fan rig ground-testing facilities. The fluid simulations captured the expected wake flow and largescale structures convecting downstream of the vane packs. A comparison between two different flow models and the experimental results revealed minimal quantitative differences in the large-scale dynamics, which gave insight into the model selection to predict such flows. Additional structural simulations were performed to estimate the forcing and response of the vane packs when subjected to the aerodynamic loading. The results showed vortex shedding was highly unlikely to cause large amplitude vibrations and structural failures. In all analyses, the primary results were correlated with common vane parameters and operating conditions to evaluate their impact on the wake dynamics. The motivation, methodology, and results of the following research is presented to better understand the wake interactions, computational predictive capabilities, and structural dynamics associated with vortex shedding from complex vane packs. Although the results directly relate to StreamVane distortion generator technology, the qualitative and quantitative comparisons between the selected methods, geometry parameters, and flow conditions can be extrapolated to modern turbomachinery components in general. Therefore, this dissertation aims to benefit distortion generator and turbomachinery designers by providing insight into the underlying physics and overall modeling techniques of the wake dynamics in highly three-dimensional, complex components.

As a contribution to advancing turbofan engine ground test technology in support of propulsion system integration in modern conceptual aircraft, a novel inlet distortion generator (ScreenVaneTM) was invented. The device simultaneously reproduces combined inlet total pressure and swirl distortion elements in a tailored profile intended to match a defined turbofan engine inlet distortion profile. The device design methodology was intended to be sufficiently generic to be utilized in support of any arbitrary inlet distortion profile yet adequately specific to generate high-fidelity inlet distortion profile simulation. For the current investigation, a specific inlet distortion profile was defined using computational analysis of a conceptual boundary layer ingesting S-duct turbofan engine inlet. The resulting inlet distortion profile, consisting of both total pressure and swirl distortion elements, was used as the objective profile to be matched by the ScreenVane in a turbofan engine ground test facility. A ScreenVane combined inlet total pressure and swirl distortion generator was designed, computationally analyzed, and experimentally validated. The design process involved specifying a total pressure loss screen pattern and organizing a unique arrangement of swirl inducing turning vanes. Computational results indicated that the ScreenVane manufactured distortion profile matched the predicted S-duct turbofan engine inlet manufactured distortion profile with excellent agreement in pattern shape, extent, and intensity. Computational full-field total pressure recovery and swirl angle profiles matched within approximately 1% and 2.5° (RMSD), respectively. Experimental turbofan engine ground test results indicated that the ScreenVane manufactured distortion profile matched the predicted S-duct turbofan engine inlet manufactured distortion profile with excellent agreement in pattern shape, extent, and intensity. Experimental full-field total pressure recovery and swirl angle profiles matched within approximately 1.25% and 3.0° (RMSD), respectively. Following the successful reproduction of the S-duct turbofan engine inlet manufactured distortion profile, a turbofan engine response evaluation was conducted using the validated ScreenVane inlet distortion generator. Flow measurements collected at discrete planes immediately upstream and downstream of the fan rotor isolated the component for performance analysis. Based on the results of this particular engine and distortion investigation, the adiabatic fan efficiency was negligibly altered while operating with distorted inflow conditions when compared to nominal inflow conditions. Fuel flow measurements indicated that turbofan engine inlet air mass flow specific fuel consumption increased by approximately 5% in the presence of distortion. While a single, specific turbofan engine inlet distortion profile was studied in this investigation, the ScreenVane methodology, design practices, analysis approaches, manufacturing techniques, and experimental procedures are applicable to any arbitrary, realistic combined inlet total pressure and swirl distortion. / Doctor of Philosophy / As a contribution to advancing turbofan engine ground test technology in support of propulsion system integration in modern conceptual aircraft, a novel inlet distortion generator (ScreenVaneTM) was invented. The device simultaneously reproduces combined inlet total pressure and swirl distortion elements in a tailored profile intended to match a defined turbofan engine inlet distortion profile. The device design methodology was intended to be sufficiently generic to be utilized in support of any arbitrary inlet distortion profile yet adequately specific to generate high-fidelity inlet distortion profile simulation. For the current investigation, a specific inlet distortion profile was defined using computational analysis of a conceptual boundary layer ingesting S-duct turbofan engine inlet. The resulting inlet distortion profile, consisting of both total pressure and swirl distortion elements, was used as the objective profile to be matched by the ScreenVane in a turbofan engine ground test facility. A ScreenVane combined inlet total pressure and swirl distortion generator was designed, computationally analyzed, and experimentally validated. The design process involved specifying a total pressure loss screen pattern and organizing a unique arrangement of swirl inducing turning vanes. Computational and experimental results indicated that the ScreenVane manufactured distortion profile matched the predicted S-duct turbofan engine inlet manufactured distortion profile with excellent agreement in pattern shape, extent, and intensity. Following the successful reproduction of the S-duct turbofan engine inlet manufactured distortion profile, a turbofan engine response evaluation was conducted using the validated ScreenVane inlet distortion generator. Flow measurements collected at discrete planes immediately upstream and downstream of the fan rotor isolated the component for performance analysis. Based on the results of this particular engine and distortion investigation, the adiabatic fan efficiency was negligibly altered while operating with distorted inflow conditions when compared to nominal inflow conditions. Fuel flow measurements indicated that turbofan engine inlet air mass flow specific fuel consumption increased in the presence of distortion. While a single, specific turbofan engine inlet distortion profile was studied in this investigation, the ScreenVane methodology, design practices, analysis approaches, manufacturing techniques, and experimental procedures are applicable to any arbitrary, realistic combined inlet total pressure and swirl distortion.

The use of serpentine boundary layer ingesting (BLI) diffusers offers a significant benefit to the performance of Blended Wing Body aircraft. However, the inherent diffuser geometry combined with a thick ingested boundary layer creates strong secondary flows that lead to severe flow distortion at the engine face, increasing the possibility of engine surge. This study investigated the use of enabling active flow control methods to reduce engine-face distortion. An ejector-pump based system of fluidic actuators was used to directly manage the diffuser secondary flows. This system was modeled computationally using a boundary condition jet modeling method, and tested in an ejector-driven wind tunnel facility. This facility is capable of simulating the high-altitude, high subsonic Mach number conditions representative of BWB cruise conditions, specifically a cruise Mach number of 0.85 at an altitude of 39,000 ft. The tunnel test section used for this experiment was designed, built, and tested as a validation tool for the computational methods. This process resulted in the creation of a system capable of efficiently investigating and testing the fundamental mechanisms of flow control in BLI serpentine diffusers at a minimum of time and expense. Results of the computational and wind tunnel analysis confirmed the large potential benefit of adopting fluidic actuators to control flow distortion in serpentine BLI inlets. Computational analysis showed a maximum 71% reduction in flow distortion at the engine face through the use of the Pyramid 1 ejector scheme, and a 68% reduction using the Circumferential ejector scheme. However, the flow control systems were also found to have a significant impact on flow swirl. The Pyramid 1 ejector scheme was found to increase AIP flow swirl by 64%, while the Circumferential ejector scheme reduced flow swirl by 30%. Computational analyses showed that this difference was the result of jet interaction. By keeping the jet flows separate and distinct, the diffuser secondary flows could be more efficiently managed. For this reason, the most practically effective flow control scheme was the Circumferential ejector scheme. Experimental results showed that the computational analysis slightly over-predicted flow distortion. However, the trends are accurately predicted despite slight variances in freestream Mach number between runs and a slightly lower tested altitude. / Master of Science

A three-dimensional CFD program was used to predict the flow field that would enter a downstream fan or compressor rotor under the influence of an upstream thermal distortion. Two distortion generation techniques were implemented in the model; (1) a thermal source and (2) a heated flow injection method. Results from the investigation indicate that both total pressure and velocity boundary conditions at the compressor face are made non-uniform by the upstream thermal distortion, while static pressure remains nearly constant. Total pressure at the compressor face was found to vary on the order of 10%, while velocity varies from 50-65%. Therefore, in modeling such flows, neither of these latter two boundary conditions can be assumed constant under these conditions. The computational model results for the two distortion generation techniques were compared to one another and evaluations of the physical practicality of the thermal distortion generation methods are presented. Both thermal distortion methods create total temperature distortion magnitudes at the compressor face that may affect rotor blade vibration. Both analyses show that holding static pressure constant is an appropriate boundary condition for flow modeling at the compressor inlet. The analyses indicate that in addition to the introduction of a thermal distortion, there is a potential to generate distortion in total pressure, Mach number, and velocity. Depending on the method of thermally distorting the inlet flow, the flow entering the compressor face may be significantly non-uniform. The compressor face boundary condition results are compared to the assumptions of a previous analysis (Kenyon et al., 2004) in which a 25 R total temperature distortion was applied to a computational fluid dynamics (CFD) model of a fan geometry to obtain unsteady blade pressure loading. Results from the present CFD analyses predict similar total temperature distortion magnitudes corresponding to the total temperature variation used in the Kenyon analyses. However, the results indicate that the total pressure and circumferential velocity boundary conditions assumed uniform in the Kenyon analyses could vary by the order of 2% in total pressure and approximately 8% in velocity distortion. This supports the previously stated finding that assuming a uniform total pressure profile at the compressor inlet may be an appropriate approximation with the presence of a weak thermal distortion, while assuming a constant circumferential velocity boundary condition is likely not sufficiently accurate for any thermal distortion. In this work, the referenced Kenyon investigation and others related to the investigation of distortion-induced aeromechanical effects in this compressor rotor have assumed no aerodynamic coupling between the duct flow and the rotor. A full computational model incorporating the interaction between the duct flow and the fan rotor would serve to alleviate the need for assuming boundary conditions at the compressor inlet. / Master of Science

An experimental and analytical investigation was conducted to gain insight and ultimately predict the dynamic flow response of a fan rotor with inlet flow distortion. Rotor exit total pressure circumferential profiles were accurately predicted using frequency response functions derived from experimental rotor response data. Using these predicted profiles, an initial attempt was made at predicting the dynamic (distorted) stage characteristics of the test machine with promising results. The first step of this research was an experimental investigation to gather unsteady rotor response data. The steady three-dimensional inlet flow of an isolated rotor subjected to inlet distortion was obtained using a five-hole pneumatic prism probe. Exit flow dynamic wake data were obtained using a piggyback steady/unsteady total pressure probe in non-nulling mode. Inlet and exit data were collected for eighteen different combinations of distortion level, operating point, and measurement span. Frequency response functions were generated and then averaged for each operating regime, span, and distortion intensity, assuming the data to be stationary and ergodic. These 'generalized' FRF's were used to predict the rotor exit total pressure profile. These pressure profiles were then used in an initial attempt to predict the dynamic stage (distorted) characteristics of the test machine. Best predictions resulted when an FRF was used for individual operating regimes, defined with respect to rotor blade mean aerodynamic loading. / Master of Science