Abstract: This paper presents the results of an experimental investigation into the application of inverter-based variable speed drives to positive displacement rotary compressors. Designs and implements a DSP-microprocessor based of an inverter drive for high-efficiency compressor used in air conditioner. We control the compressor with sine PWM and V/F scheme. Permanent magnet synchronous motor has potential for energy saving in general applications on compressor drives. Permanent magnet synchronous motor drives are used for applications like compressors¡Awhere high dynamic performance is not a demand¡Asimple V/F control strategies may be sufficient to obtain the required control performance. For energy saving to find the best control strategy for an inverter drive for high efficiency compressor used in air conditioner.

The analysis of the feature and application of linear induction motors at work have been performed; mathematical models of linear motors have been studied; mathematical description of induction machine have been presented; coordinate transform have been studied; dynamic equations in moving and move-less systems of axes of linear induction motor have been presented; the analysis of the classification of induction drives control modes have been performed. Four models of the frequency-regulated electric drives with linear induction motors have been studied: when the motor is supplied from variable frequency mains supply, when the motor is supplied from frequency converter, when frequency is changed by program, when frequency is changed in close-loop by vector control system. The characteristics of those models have been compared and performed. The received results are summarized in the conclusions.

In this thesis, a new approach for single-stage power factor correction converters is proposed to increase their power ratings to be in the multiple kilowatts levels. The proposed techniques are based on the utilization of modified three-level resonant converter topologies. These topologies provide low component stresses, high frequency operation, zero voltage switching, applicability under a wide range of input and output conditions as well as added control flexibility. The proposed control algorithms are based on a combination of variable frequency and asymmetrical pulse width modulation control or variable frequency and phase shift modulation control. In either case, the variable frequency control is used to tightly regulate the output voltage, whereas, pulse width or phase shift modulation is used to regulate the dc-bus voltage as well as the input power factor. New converter topologies, their operation and steady state and dynamic analyses are presented in details. A modelling approach based on average multiple frequency methods is also proposed. This approach leads to the development of a full order state space model with the two control variables explicitly separated allowing a better controller design. The model can be used either at high level of detail expressing the non-linearities of the system or it can readily be simplified to a linear decoupled model for approximate solutions. Finally, a discrete time controller for the proposed converters, which is suitable for FPGA implementation, is presented. Analytical, simulation and experimental results are provided to verify the proposed concepts. / Thesis (Ph.D, Electrical & Computer Engineering) -- Queen's University, 2008-01-30 14:28:15.725

No description available.

The main function of the power grid is to transfer electric energy from generating facilities to consumers. To have a reliable and economical supply of electricity, large amounts of electric energy often have to be transferred over long distances. The transmission system has a limited capacity to transfer electric power, called the transfer capacity. Severe system failures may follow if the transfer capacity is reached during operation. Due to uncertainties, such as the random failure of system components, the transfer capacity for the near future is not readily determinable. Also, due to market principles, and reaction times and ramp rates of production facilities, power flow control is not fully flexible. Therefore, a transfer limit, which is below the transfer capacity, is decided and preventative actions are taken when the transfer reaches this limit. In this thesis an approach to deciding an optimal strategy for power flow control through activation of regulating bids on the regulating power market is outlined. This approach leads to an optimal definition of transfer limits as the boundary between the domain where no bid should be activated and the domains where bids should be activated. The approach is based on weighing the expected cost from system failures against the production cost. This leads to a stochastic impulse control problem for a Markov process in continuous time. The proposed method is a novel approach to decide transfer limits in power system operation. The method is tested in a case study on the IEEE 39 bus system, that shows promising results. In addition to deciding optimal transfer limits, it is also investigated how the transfer capacity can be enhanced by controlling components in the power system to increase stability. / QC 20111010

Dans ce travail de thèse nous nous sommes intéressés principalement à la récupération de l'énergie mécanique et plus particulièrement l'énergie vibratoire. Cette technologie repose sur l'utilisation des transducteurs résonants, ces dispositifs permettent d'amplifier l'amplitude de vibration et donc de stocker d'avantage d'énergie mécanique dans le convertisseur à la résonance. La quantité de l'énergie en sortie du convertisseur chute lorsque la fréquence de vibration n'est plus égale à la fréquence de résonance, il est donc nécessaire d'assurer un asservissement de la fréquence de résonance de la structure de récupération d'énergie vibratoire sur la fréquence de vibration, si possible sur tout le spectre fréquentiel que couvre la source de vibration. L'objectif de la thèse est de proposer des solutions, à basse consommation, permettant d'assurer un ajustement dynamique en temps réel de la fréquence de résonance en fonction de la fréquence de vibration. Les travaux de cette thèse s'articulent autour de trois solutions : 1) Ajustement de la fréquence de résonance par application d'un champ électrique dans un matériau piézoélectrique 2) Ajustement de la fréquence de résonance par adaptation de la charge électrique d'un matériau piézoélectrique 3) Amplification du mouvement vibratoire par technique de rebond Une modélisation et optimisation à la fois de la plage de fréquence de fonctionnement et de la conversion mécano-électrique ont été réalisées. Trois structures ont été développées et testées et permettent de valider chacune des trois approches. Enfin, une électronique très basse consommation a été mise au point pour asservir en temps réel la fréquence de résonance sur la fréquence de la source de vibration et optimiser le taux d'énergie électrique extraite du système (pour maintenir un facteur de qualité de la structure optimum). / The work of this thesis is focused on the mechanical energy harvesting. This technology is generally based on the use of resonant transducers. Such systems work efficiently when their resonant frequency is equal to the vibration one. Otherwise, the output power from the harvester drops dramatically. Hence, it's necessary to ensure a continuous control of the resonant frequency of the harvester in order to avoid a possible shift between the resonant frequency and the vibration one, and doing this over the frequency spectrum covered by the vibration source. The main goal of this thesis is to develop new efficient solutions able to control in real time and tune the resonant frequency, these solutions should be low power consumption. During this thesis, three solutions have been developed: 1) adjustement of the resonant frequency by applying an electric field on the piezoelectric material; 2) adjustement of the resonant by adapting the electrical load; 3) the amplification of the structure relative displacement using a rebound technique. Modelling and optimization of both the frequency adjustment techniques and the mechanical-to-electrical conversion were performed. Three structures have been developed, tested and used to validate the three approaches. Finally, a very low power consumption electronic has been developed for a real time control of the resonant frequency, by regarding the vibration frequency, and also to optimize the extracted electrical energy from the harvester by maintaining an optimum quality factor.

Un réseau insulaire est un système fragile et sensible aux variations de charge ou de production notamment d'origine renouvelable et intermittent. Ce problème devient crucial avec l'augmentation dans ces réseaux de production éolien ou PV en remplacement des sources actuelles (diesel, etc.). Cela impacte directement la stabilité du réseau, notamment la fréquence. Les moyens de stockage pourraient dès lors participer au réglage primaire de la fréquence, en limitant des variations après une perturbation. L'objectif de cette thèse consiste ainsi à étudier la participation du stockage pour maintenir la stabilité en fréquence dans un réseau insulaire en augmentant le taux de pénétration d'énergie renouvelable. Un algorithme de dimensionnement et différentes stratégies de contrôle du système de stockage ont ainsi été développés en fonction de variations réellement observées sur un parc PV. Notre étude est séparée en 2 parties. La première partie concerne la modélisation de l'intermittence de la production PV. La puissance PV a ainsi été caractérisée en fonction de son impact sur la variation de la fréquence, afin de définir toute situation critique. Ensuite, la technologie et les critères de dimensionnement du dispositif de stockage et la stratégie de pilotage et de contrôle-commande pour surveiller et contrôler le système de stockage ont été proposés et validées à partir de simulations. Ces stratégies ont été élaborées soit à partir de critères qualitatifs définie dans le domaine temporel, soit à partir d'une stratégie de filtrage fréquentiel des différentes sources. Par ailleurs, pour garantir des critères de robustesse vis-à-vis des incertitudes paramétriques notamment sur la mesure des variations PV, une commande robuste (utilisant un contrôleur H infinie) a été conçu et validé. Les différentes stratégies proposées peuvent plus ou moins réduire la variation de la fréquence suite à perturbation et permettre de réduire significativement la participation de la source principale d'énergie au réglage de la fréquence. Par ailleurs, les résultats ont permis de faire un lien entre le taux de pénétration des énergies renouvelables photovoltaïques dans un micro réseau et la tenue en fréquence dans ce réseau. / Frequency of isolated microgrids is highly sensitive to active power variation of loads and productions because of the inertia equivalent of this grid is small (limited number of thermal generators). Furthermore, the increasing of renewable energy in this grid causes frequency more risky to be instable because of its intermittency of power. In this thesis, energy storage is the selected solution to maintain the frequency stability of isolated microgrids with high penetration rate of renewable energy. It will participate to the primary frequency control which is the first control that takes action to limit the frequency deviation after disturbance. Therefore, the objective of this thesis is to design the appropriate size and strategy of energy storage in isolated microgrids with high penetration rate of photovoltaic. Proposed strategies will link to power variation of PV. Therefore, the different situations of photovoltaic power variations and their impacts on the system frequency had been firstly characterized and studied in order to specify the critical situation of frequency variation. Then, different strategies for energy storage and their sizes were defined from these two studies. The strategy limit dPpv diagram and filter strategy were proposed to define the participated power of energy storage in primary frequency control from the measured power variation of PV. Furthermore, controller H infinity which is robust control was also proposed. Finally, energy storage control system was validated by RTLAB (real time simulation) which enable us to simulate the hardware. The results show that energy storage by proposed strategies is able to stabilize frequency of the power system by limiting the frequency deviation to be within an acceptable range after occurrence of any disturbance. The proposed strategies can increase larger participated power of the energy storage with less frequently than the classic droop control.

Submitted by Marco Antonio Oliveira da Silva (maosilva@ipen.br) on 2017-11-09T11:26:50Z No. of bitstreams: 0 / Made available in DSpace on 2017-11-09T11:26:50Z (GMT). No. of bitstreams: 0 / Os lasers Raman permitem a exploração de novos comprimentos de onda, não comumente acessíveis, graças ao Espalhamento Raman Estimulado. Unidos a processos de conversão não linear, abrem-se campos para emissão de comprimentos de onda na região do visível no espectro eletromagnético. Com uma mesma configuração, diversas combinações de cristais possibilitam a geração de múltiplas frequências, transformando esse tipo de laser em um dispositivo compacto e barato quando comparado com outras tecnologias existentes. Este trabalho apresenta a busca da conversão intracavidade em frequências de lasers Raman, em uma configuração linear. Com dois comprimentos de onda de bombeamento de energia (797 nm e 872 nm), diodos semicondutores foram utilizados para acessar dois picos de absorção do cristal Nd:YLF. O bombeamento em 797 nm levou a emissão fundamental em 908 nm. E através do cristal KGW, com linhas de emissão Stokes, um novo comprimento de onda foi alcançado, em 990 nm. Com o cristal dobrador, BiBO, soma de frequência e segundo harmônico foram gerados, permitindo as emissões em uma região espectral azul bastante larga (450 500 nm). Com o bombeamento em 872 nm, uma emissão de três níveis no cristal Nd:YLF não foi possível, conseguindo apenas a emissão em 1064 nm, linha comum para cristais de neodímio. Uma outra cavidade foi estudada, porém com bombeamento em 880 nm e cristal de Nd:YVO4, conhecido por ser self-Raman. Com uma configuração linear semelhante à anteriormente citada, somente sua linha de emissão fundamental em 914 nm foi obtida, não sendo possível com as condições trabalhadas a emissão Stokes, que permitisse dar continuidade ao estudo. / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energéticas e Nucleares - IPEN-CNEN/SP

The growing demand for wireless communication systems is driving the integration of radio frequency (RF) front-ends on the same chip with multi-band functionality and higher spectral efficiency. Microelectromechanical systems (MEMS) have an overarching applicability to RF communications and are critical components in facilitating this integration process. Among a variety of RF MEMS devices, piezoelectric MEMS resonators have sparked significant research and commercial interest for use in oscillators, filters, and duplexers. Compared to their bulky quartz crystal and surface acoustic wave (SAW) counterparts, MEMS resonators exhibit impressive advantages of compact size, lower production cost, lower power consumption, and higher level of integration with CMOS fabrication processes. One of the promising piezoelectric MEMS resonator technologies is the aluminum nitride (AlN) contour mode resonator (CMR). On one hand, AlN is chemically stable and offers superior acoustic properties such as large stiffness and low loss. Furthermore, CMRs offer low motional resistance over a broad range of frequencies (few MHZ to GHz), which are lithographically-definable on the same silicon substrates. To date, RF MEMS resonators (include CMRs) have been extensively studied; however, one aspect that was not thoroughly investigated is how to modulate/tune their equivalent parameters to enhance their performance in oscillators and duplexers. The goal of this thesis is to investigate various modulation methods to improve the thermal stability of the resonator, its “effective” quality factor when used in an oscillator, and build completely novel non-reciprocal components. Broadly defined, modulation refers to the exertion of a modifying or controlling influence on something, herein specifically, the resonator admittance. In this thesis, three categories of modulation methods are investigated: thermal modulation, force modulation, and external electronic modulation. Firstly, the AlN CMR’s center frequency can be tunned by the applied thermal power to the resonator body. The resonator temperature is kept constant (for example, 90 °C) via a temperature sensor and feedback control such that the center frequency is stable over the whole operation temperature range of interest (e.g. –35 to 85 °C). The maximum power consumption to sustain the maximum temperature difference (120 ºC in this thesis) between resonator and ambient is reduced to a value as low as 353 μW – the lowest ever reported for any MEMS device. These results were attained while simultaneously maintaining a high quality factor (up to 4450 at 220 MHz device). The feedback control was implemented by either analog circuits or via a microprocessor. The analog feedback control, which innovatively utilized a dummy resistor to compensate for temperature gradients, resulted in a total power consumption of 3.8 mW and a frequency stability of 100 ppm over 120 ºC. As for the digital compensation, artificial neural network algorithm was employed to facilitate faster calibration of look-up tables for multiple frequencies. This method attained a frequency stability of 14 ppm over 120 ºC. The second modulation method explored in this thesis is based on the use of an effective external force to enhance the 3-dB quality factor of AlN CMRs and improve the phase noise performance of resonator-based oscillators. The force modulation method was embodied in a two-port device, where one of the two ports is used as a one-port resonator and the other is driven by an external signal to effectively apply an external force to the first port. Through this technique, the quality factor of the resonator was boosted by 140 times (up to 150,000) and the phase noise of the corresponding oscillator realized using the resonator was reduced by 10 dBc/Hz. Lastly, a novel magnetic-free electrical circulator topology that facilitates the development of in-band full duplexers (IBFD) for simultaneous transmit and receive (STAR) is proposed and modeled. Fundamentally, a linear time-invariant (LTI) filter network parametrically modulated via a switching matrix is used to break the reciprocity of the filter. The developed model accurately predicts the circulator behavior and shows very good agreement with the experimental results for a 21.4 MHz circulators built with MiniCircuit filter and switch components. Furthermore, a high frequency (1.1 GHz) circulator was synthesized based on AlN MEMS bandpass filters and CMOS RF switches, hence showing a compact approach that can be used in handheld devices. The modulation frequency and duty cycle are optimized so that the circulator can provide up to 15 dB of isolation over the filter bandwidth while good power transfer between the other two ports is maintained. The demonstrated device is expected to intrinsically offer low noise and high linearity. The combination of the first two modulation methods facilitates the implementation of monolithic, temperature-stable, ultra-low noise, multi-frequency oscillator banks. The third modulation technique that was investigated sets the path for the development of CMOS-compatible in-band full duplexers for simultaneous transmit and receive and thus facilitates the efficient utilization of the electromagnetic spectrum. With the aid of all these three modulation approaches, the author believes that a fully integrated, multi-frequency, spectrum-efficient transceiver is enabled for next-generation wireless communications.

Many AC grids suffer from decreased frequency stability due to less system inertia. This has increased the risk of large-scale blackouts. This thesis and its papers address the frequency stability problem from a hydropower perspective. Grid frequency stability assessments often require accurate system inertia estimates. One approach is to estimate the inertia of all individual power plants and sum up the results. We implemented three inertia estimation methods on a Kaplan unit and compared their results. The generator contributed with 92-96% of the unit inertia, which verified the results from previous studies. However, the three methods estimated slightly different values for the unit inertia, which raises the question of when to use which method. Hydropower often deliver frequency control, yet we found no studies which validate Kaplan turbine models for large grid frequency disturbances on strong grids. Therefore, we performed frequency control tests on a Kaplan unit, implemented three hydropower models, and compared the simulation results to the measurement data. The models overestimated the change in output power and energy delivered within the first few seconds after a large change in frequency. Thus, it is important to have sufficient stability margin when using these types of hydropower models to assess the grid frequency stability. The Nordic transmission system operators are updating their frequency control requirements. We used measurement data and simulation models to assess whether improved runner blade angle control could help a Kaplan unit fulfill the coming requirements. The results showed that improved runner control does not improve the performance sufficiently for requirements fulfillment. The requirements are based on an assumption on minimum system inertia and became easier to fulfill if they were implemented with more system inertia. Thus, more inertia could allow more participants to deliver frequency control in the Nordic grid.