LOW power operation for wireless radio receivers has been gaining importance lately on account of the recent spurt of growth in the usage of ubiquitous embedded mobile devices. These devices are becoming relevant in all domains of human influence. In most cases battery life for these devices continue to be an us-age bottleneck as energy storage techniques have not kept pace with the growing demand of such mobile computing devices. Many applications of these radios have limitations on recharge cycle, i.e. the radio needs to last out of a battery for long duration. This will specially be true for sensor network applications and for im-plantable medical devices. The search for low power wireless receivers has become quite advanced with a plethora of techniques, ranging from circuit to architecture to system level approaches being formulated as part of standard design procedures. However the next level of optimization towards “Smart” receiver systems has been gaining credence and may prove to be the next challenge in receiver design and de-velopment. We aim to proceed further on this journey by proposing Power Scalable Wireless Receivers (PSRX) which have the capability to respond to instantaneous performance requirements to lower power even further. Traditionally low power receivers were designed for worst-case input conditions, namely low signal and high interference, leading to large dynamic range of operation which directly im-pacts the power consumption. We propose to take into account the variation in performance required out of the receiver, under varying Signal and Interference conditions, to trade-off power. We have analyzed, designed and implemented a Power Scalable Receiver tar-geted towards low data-rate receivers which can work for Zigbee or Bluetooth Low Energy (BLE) type standards. Each block of such a receiver system was evaluated for performance-power trade-offs leading to identification of tuning/control knobs at the circuit architecture level of the receiver blocks. Then we developed an usage algorithm for finding power optimal operational settings for the tuning knobs, while guaranteeing receiver reception performance in terms of Bit-Error-Rate (BER). We have proposed and demonstrated a novel signal measurement system to gen-erate digitized estimates of signal and interference strength in the received signal, called Received Signal Quality Indicator (RSQI). We achieve a RSQI average energy consumption of 8.1nJ with a peak energy consumption of 9.4nJ which is quite low compared to the packet reception energy consumption for low power receivers, and will be substantially lower than the energy savings which will be achieved from a power scalable receiver employing a RSQI. The full PSRX system was fabricated in UMC 130nm RF-CMOS process to test out our concepts and to formally quantify the power savings achieved by following the design methodology. The test chip occupied an area of 2.7mm2 with a peak power consumption of 5.5mW for the receiver chain and 18mW for the complete PSRX. We were able to meet the receiver performance requirements for Zigbee standard and achieved about 5X power savings for the range of input condition variations.

Thesis submitted in fulfillment of the requirements for the degree Master of Technology:Electrical Engineering in the Faculty ofEngineering at the Cape Peninsula University of Technology Supervisor:Prof MTE KAHN Bellville December 2013 / The work presented in this thesis consists of the simulation of a cooling plant for a future mobile satellite ground station in order to minimize the effects of the thermal noise and to maintain comfort temperatures onboard the same station. Thermal problems encountered in mobile satellite ground stations are a source of poor quality signals and also of the premature destruction of the front end microwave amplifiers. In addition, they cause extreme discomfort to the mission operators aboard the mobile station especially in hot seasons. The main concerns of effective satellite system are the quality of the received signal and the lifespan of the front end low noise amplifier (LNA). Although the quality of the signal is affected by different sources of noise observed at various stages of a telecommunication system, thermal noise resulting from thermal agitation of electrons generated within the LNA is the predominant type. This thermal noise is the one that affects the sensitivity of the LNA and can lead to its destruction. Research indicated that this thermal noise can be minimized by using a suitable cooling system. A moveable truck was proposed as the equipment vehicle for a mobile ground station. In the process of the cooling system development, a detailed quantitative study on the effects of thermal noise on the LNA was conducted. To cool the LNA and the truck, a 2 kW solar electric vapor compression system was found the best for its compliance to the IEA standards: clean, human and environment friendly. The principal difficulty in the development of the cooling system was to design a photovoltaic topology that would ensure the solar panels were always exposed to the sun, regardless the situation of the truck. Simulation result suggested that a 3.3 kW three sided pyramid photovoltaic topology would be the most effective to supply the power to the cooling system. A battery system rated 48 V, 41.6 Ah was suggested to be charged by the PV system and then supply the power to the vapor compression system. The project was a success as the objective of this project has been met and the research questions were answered.

A 5 GHz continuous unlicensed bandwidth is available at millimeter-wave (mm-wave) frequencies around 60 GHz and offers the prospect for multi gigabit wireless applications. The inherent atmospheric attenuation at 60 GHz due to oxygen absorption makes the frequency range ideal for short distance communication networks. For these mm-wave wireless networks, the low noise amplifier (LNA) is a critical subsystem determining the receiver performance i.e., the noise figure (NF) and receiver sensitivity. It however proves challenging to realise high performance mm-wave LNAs in a silicon (Si) complementary metal-oxide semiconductor (CMOS) technology. The mm-wave passive devices, specifically on-chip inductors, experience high propagation loss due to the conductivity of the Si substrate at mm-wave frequencies, degrading the performance of the LNA and subsequently the performance of the receiver architecture. The research is aimed at realising a high performance mm-wave LNA in a Si BiCMOS technology. The focal points are firstly, the fundamental understanding of the various forms of losses passive inductors experience and the techniques to address these issues, and secondly, whether the performance of mm-wave passive inductors can be improved by means of geometry optimising. An associated hypothesis is formulated, where the research outcome results in a preferred passive inductor and formulates an optimised passive inductor for mm-wave applications. The performance of the mm-wave inductor is evaluated using the quality factor (Q-factor) as a figure of merit. An increased inductor Q-factor translates to improved LNA input and output matching performance and contributes to the lowering of the LNA NF. The passive inductors are designed and simulated in a 2.5D electromagnetic (EM) simulator. The electrical characteristics of the passive structures are exported to a SPICE netlist which is included in a circuit simulator to evaluate and investigate the LNA performance. Two LNAs are designed and prototyped using the 13μ-m SiGe BiCMOS process from IBM as part of the experimental process to validate the hypothesis. One LNA implements the preferred inductor structures as a benchmark, while the second LNA, identical to the first, replaces one inductor with the optimised inductor. Experimental verification allows complete characterization of the passive inductors and the performance of the LNAs to prove the hypothesis. According to the author's knowledge, the slow-wave coplanar waveguide (S-CPW) achieves a higher Q-factor than microstrip and coplanar waveguide (CPW) transmission lines at mm-wave frequencies implemented for the 130 nm SiGe BiCMOS technology node. In literature, specific S-CPW transmission line geometry parameters have previously been investigated, but this work optimises the signal-to-ground spacing of the S-CPW transmission lines without changing the characteristic impedance of the lines. Optimising the S-CPW transmission line for 60 GHz increases the Q-factor from 38 to 50 in simulation, a 32 % improvement, and from 8 to 10 in measurements. Furthermore, replacing only one inductor in the output matching network of the LNA with the higher Q-factor inductor, improves the input and output matching performance of the LNA, resulting in a 5 dB input and output reflection coefficient improvement. Although a 5 dB improvement in matching performance is obtained, the resultant noise and gain performance show no significant improvement. The single stage LNAs achieve a simulated gain and NF of 13 dB and 5.3 dB respectively, and dissipate 6 mW from the 1.5 V supply. The LNA focused to attain high gain and a low NF, trading off linearity and as a result obtained poor 1 dB compression of -21.7 dBm. The LNA results are not state of the art but are comparable to SiGe BiCMOS LNAs presented in literature, achieving similar gain, NF and power dissipation figures. / Dissertation (MEng)--University of Pretoria, 2012. / Electrical, Electronic and Computer Engineering / unrestricted

The prevalence of wireless standards and the introduction of dynamic standards/applications, such as software-defined radio, necessitate the next generation wireless devices that integrate multiple standards in a single chip-set to support a variety of services. To reduce the cost and area of such multi-standard handheld devices, reconfigurability is desirable, and the hardware should be shared/reused as much as possible. This research proposes several novel circuit topologies that can meet various specifications with minimum cost, which are suited for multi-standard applications. This doctoral study has two separate contributions: 1. The low noise amplifier (LNA) for the RF front-end; and 2. The analog-to-digital converter (ADC). The first part of this dissertation focuses on LNA noise reduction and linearization techniques where two novel LNAs are designed, taped out, and measured. The first LNA, implemented in TSMC (Taiwan Semiconductor Manufacturing Company) 0.35Cm CMOS (Complementary metal-oxide-semiconductor) process, strategically combined an inductor connected at the gate of the cascode transistor and the capacitive cross-coupling to reduce the noise and nonlinearity contributions of the cascode transistors. The proposed technique reduces LNA NF by 0.35 dB at 2.2 GHz and increases its IIP3 and voltage gain by 2.35 dBm and 2dB respectively, without a compromise on power consumption. The second LNA, implemented in UMC (United Microelectronics Corporation) 0.13Cm CMOS process, features a practical linearization technique for high-frequency wideband applications using an active nonlinear resistor, which obtains a robust linearity improvement over process and temperature variations. The proposed linearization method is experimentally demonstrated to improve the IIP3 by 3.5 to 9 dB over a 2.5–10 GHz frequency range. A comparison of measurement results with the prior published state-of-art Ultra-Wideband (UWB) LNAs shows that the proposed linearized UWB LNA achieves excellent linearity with much less power than previously published works. The second part of this dissertation developed a reconfigurable ADC for multistandard receiver and video processors. Typical ADCs are power optimized for only one operating speed, while a reconfigurable ADC can scale its power at different speeds, enabling minimal power consumption over a broad range of sampling rates. A novel ADC architecture is proposed for programming the sampling rate with constant biasing current and single clock. The ADC was designed and fabricated using UMC 90nm CMOS process and featured good power scalability and simplified system design. The programmable speed range covers all the video formats and most of the wireless communication standards, while achieving comparable Figure-of-Merit with customized ADCs at each performance node. Since bias current is kept constant, the reconfigurable ADC is more robust and reliable than the previous published works.