Yes / Antibacterial hydrogels have been intensively studied due to their wide practical potential in wound healing. However, developing an antibacterial hydrogel that is able to integrate with exceptional mechanical properties, cell affinity, and adhesiveness will remain a major challenge. Herein, a novel hydrogel with antibacterial and superior biocompatibility properties was developed using aluminum ions (Al3+) and alginate− dopamine (Alg-DA) chains to cross-link with the copolymer chains of acrylamide and acrylic acid (PAM) via triple dynamic noncovalent interactions, including coordination, electrostatic interaction, and hydrogen bonding. The cationized nanofibrillated cellulose (CATNFC), which was synthesized by the grafting of long-chain quaternary ammonium salts onto nanofibrillated cellulose (NFC), was utilized innovatively in the preparation of antibacterial hydrogels. Meanwhile, alginate-modified dopamine (Alg-DA) was prepared from dopamine (DA) and alginate. Within the hydrogel, the catechol groups of Alg-DA provided a decent fibroblast cell adhesion to the hydrogel. Additionally, the multitype cross-linking structure within the hydrogel rendered the outstanding mechanical properties, self-healing ability, and recycling in pollution-free ways. The antibacterial test in vitro, cell affinity, and wound healing proved that the as-prepared hydrogel was a potential material with all-around performances in both preventing bacterial infection and promoting tissue regeneration during wound healing processes. / This work was supported by the National Natural Science Foundation of China (32070826 and 51861165203), the Chinese Postdoctoral Science Foundation (2019M650239, 2020T130762), the Sichuan Science and Technology Program (2019YJ0125), the State Key Laboratory of Polymer Materials Engineering (sklpme2019-2-19), the Chongqing Research Program of Basic Research and Frontier Technology (cstc2018jcyjAX0807), Chongqing Medical Joint Research Project of Chongqing Science and Technology Committee & Health Agency (2020GDRC017), and the RCUK China-UK Science Bridges Program through the Medical Research Council, and the Fundamental Research Funds for the Central Universities.

Fibras vegetais de baixo módulo de elasticidade são conhecidas pela sua capacidade de aumentar a energia absorvida durante o carregamento dos materiais cimentícios, especialmente no estágio pós-fissurado. A utilização de nanofibras celulósicas pode contribuir para a tenacificação de matrizes frágeis, tanto por melhorar o empacotamento das partículas, com o refinamento de poros, quanto pela interceptação de fissuras na escala nanométrica, com a respectiva absorção de energia. A celulose nanofibrilada provém de um recurso natural, abundante e renovável, possui bom desempenho mecânico e superfície específica elevada, o que contribui para melhorar a adesão entre as partículas de cimento. Estes fatores justificam o uso da celulose nanofibrilada e a tornam uma boa alternativa como nanoreforço de materiais cimentícios. Com isso, o objetivo deste trabalho foi a produção de celulose nanofibrilada a partir de polpa organossolve de bambu, definindo a melhor condição para sua produção e posterior utilização como reforço em compósitos híbridos (reforçados na nano e micro escalas) em comparação a compósitos reforçados somente com microfibras (polpa) pelos processos de produção por sucção e prensagem, e extrusão. A celulose nanofibrilada foi produzida utilizando-se polpa não-branqueada e branqueada, por meio de 5, 10, 15 e 20 ciclos de nanofibrilação pelo processo grinding. Foram realizados testes químicos, físicos e mecânicos para definição da condição ótima de nanofibrilação. A celulose nanofibrilada não-branqueada produzida mediante 10 ciclos foi definida como a melhor opção para utilização nos compósitos híbridos, por possuírem maior módulo de elasticidade e, em razão da sua maior estabilidade estrutural, apresentam maior resistência à degradação em meio alcalino. Os compósitos foram submetidos à cura por carbonatação acelerada para mitigação da degradação da fibra pela diminuição do pH da matriz e também para refinamento dos poros. Os compósitos foram submetidos ao teste de envelhecimento acelerado por meio de 200 ciclos de imersão e secagem para análise da sua degradação. Os compósitos híbridos e reforçados somente com polpa aos 28 dias de cura e após o envelhecimento acelerado foram submetidos aos ensaios físicos, mecânicos e microestruturais para acompanhamento do efeito da celulose nanofibrilada nas suas propriedades. Nos compósitos produzidos pelos dois processos aos 28 dias não houve diferença estatística para as propriedades físicas testadas, comparando-se os compósitos híbridos e os reforçados somente com polpa. No processo de sucção e prensagem, embora útil para ajustes na formulação e na cura do compósito híbrido, não se percebeu contribuição estatisticamente significativa da celulose nanofibrilada na formação de pontes de transferência de tensões, e, portanto sem o correspondente aumento na resistência mecânica dos compósitos. Nos compósitos extrudados, a celulose nanofibrilada atuou de modo a melhorar o comportamento mecânico do compósito híbrido em comparação ao compósito sem nanofibras. Esta melhoria pode estar associada à maior adesão entre as nanofibrilas e a matriz cimentícia, o que foi atestado pela análise microestrutural (MEV) dos compósitos. Após o envelhecimento acelerado os compósitos com e sem nanofibras produzidos pelos dois processos não apresentaram redução do desempenho mecânico, o que se atribui à menor alcalinidade provida pela carbonatação acelerada. / Low elastic modulus vegetable fibers are known for their ability to increase the energy absorbed by cement based materials while they are loaded, especially during the post-crack stage. The use of cellulose nanofibers may contribute for toughening of brittle matrices and improving particle packing by both pore refining and crack intercepting at nanoscale, with the corresponding energy absorption. Nanofibrillated cellulose comes from a natural, abundant and renewable resources, it has good mechanical peformance and high specific surface, which contributes to improve the adhesion between the cement particles. These factors justify the use of nanofibrillated cellulose and give rise to an alternative nanoreinforcement for cement based materials. Thus, the aim of this work was the production of the nanofibrillated cellulose from bamboo organosolv pulp, establishing the best condition for its production and subsequent use as reinforcement in hybrid composites (both nano and micro-scale reinforcement) compared to composites reinforced with only microfibers (pulp), produced by the slurry vacuum dewatering followed by pressing and extrusion methods. The nanofibrillated cellulose was produced submitting unbleached and bleached pulps to 5, 10, 15 and 20 nanofibrillated cycles by the grinding method. Chemical, physical and mechanical tests were carried out to define the optimal condition to nanofibrillation. The unbleached nanofibrillated cellulose produced by 10 cycles was defined as the best option to be used in hybrid composites, since their greater modulus of elasticity and, because of their greater structural chemical stability, higher resistance to degradation in alkaline environments. The composites were subjected to accelerated carbonation curing process to mitigate thedegradation of fiber by reducing the matrix pH and also to refine the pores. The composites were subjected to accelerated aging process by means of 200 wet and dry cycles to assess their degradation. The hybrid composites and the composites reinforced only with pulp at 28 days and after accelerated aging were subjected to physico-mechanical and microstructural tests to study the effect of the nanofibrillated cellulose on their properties. There was no difference in the physical properties of the hybrid composites and composites reinforced with only pulp, produced by the two processes at 28 days. For the slurry vacuum dewatering followed by pressing process, although useful for adjustments in the formulation and cure hybrid composite, there was no statistically significant contribution of the nanofibrillated cellulose in the formation of stress transfer bridges, and therefore without a corresponding increase in the mechanical strength of the composites. For the extruded composites, the nanofibrillated cellulose improved the mechanical behavior of the hybrid composite compared to the composite without nanofiber. This improvement may be associated with greater adherence between the nanofibrils and the cement matrix, which was confirmed by microstructural analysis (SEM) of the composites. After accelerated aging, the composites with and without nanofibers produced by the two processes showed no reduction in mechanical performance, which is attributed to the lower alkalinity provided by the accelerated carbonation.

Organic electronics is the study of organic materials with electronic functionality and the applications of such materials. In the 1970s, the discovery that polymers can be made electrically conductive led to an explosion within this field which has continued to grow year by year. One of the attractive features of organic electronic materials is their inherent mechanical flexibility, which has led to the development of numerous flexible electronics technologies such as organic light emitting diodes and solar cells on flexible substrates. The possibility to produce electronics on flexible substrates like plastic or paper has also had a large impact on the field of printed, electronics where inks with electronic functionality are used for large area fabrication of electronic devices using classical printing methods, such as screen printing, inkjet printing and flexography. Recently, there has been a growing interest in the use of cellulose in organic and printed electronics, not only as a paper substrate but also as a component in composite materials where the cellulose provides mechanical strength and favorable 3D-microstructures. Nanofibrillated cellulose is composed of cellulose fibers with high aspect-ratio and diameters in the nanometer range. Due to its remarkable mechanical strength, large area-to-volume ratio, optical transparency and solution processability it has been widely used as a scaffold or binder for electronically active materials in applications such as batteries, supercapacitors and optoelectronics. The focus of this thesis is on flexible devices based on conductive polymers and can be divided into two parts: (1) Composite materials of nanofibrillated cellulose and the conductive polymer PEDOT:PSS and (2) patterning of vapor phase polymerized conductive polymers. In the first part, it is demonstrated how the combination of cellulose and conductive polymers can be used to make electronic materials of various form factors and functionality. Thick, freestanding and flexible “papers” are used to realize electrochemical devices such as transistors and supercapacitors while lightweight, porous and elastic aerogels are used for sensor applications. The second focus of the thesis is on a novel method of patterning conductive polymers produced by vapor phase polymerization using UV-light. This method is used to realize flexible electrochromic smart windows with high-resolution images and tunable optical contrast.

Fibras vegetais de baixo módulo de elasticidade são conhecidas pela sua capacidade de aumentar a energia absorvida durante o carregamento dos materiais cimentícios, especialmente no estágio pós-fissurado. A utilização de nanofibras celulósicas pode contribuir para a tenacificação de matrizes frágeis, tanto por melhorar o empacotamento das partículas, com o refinamento de poros, quanto pela interceptação de fissuras na escala nanométrica, com a respectiva absorção de energia. A celulose nanofibrilada provém de um recurso natural, abundante e renovável, possui bom desempenho mecânico e superfície específica elevada, o que contribui para melhorar a adesão entre as partículas de cimento. Estes fatores justificam o uso da celulose nanofibrilada e a tornam uma boa alternativa como nanoreforço de materiais cimentícios. Com isso, o objetivo deste trabalho foi a produção de celulose nanofibrilada a partir de polpa organossolve de bambu, definindo a melhor condição para sua produção e posterior utilização como reforço em compósitos híbridos (reforçados na nano e micro escalas) em comparação a compósitos reforçados somente com microfibras (polpa) pelos processos de produção por sucção e prensagem, e extrusão. A celulose nanofibrilada foi produzida utilizando-se polpa não-branqueada e branqueada, por meio de 5, 10, 15 e 20 ciclos de nanofibrilação pelo processo grinding. Foram realizados testes químicos, físicos e mecânicos para definição da condição ótima de nanofibrilação. A celulose nanofibrilada não-branqueada produzida mediante 10 ciclos foi definida como a melhor opção para utilização nos compósitos híbridos, por possuírem maior módulo de elasticidade e, em razão da sua maior estabilidade estrutural, apresentam maior resistência à degradação em meio alcalino. Os compósitos foram submetidos à cura por carbonatação acelerada para mitigação da degradação da fibra pela diminuição do pH da matriz e também para refinamento dos poros. Os compósitos foram submetidos ao teste de envelhecimento acelerado por meio de 200 ciclos de imersão e secagem para análise da sua degradação. Os compósitos híbridos e reforçados somente com polpa aos 28 dias de cura e após o envelhecimento acelerado foram submetidos aos ensaios físicos, mecânicos e microestruturais para acompanhamento do efeito da celulose nanofibrilada nas suas propriedades. Nos compósitos produzidos pelos dois processos aos 28 dias não houve diferença estatística para as propriedades físicas testadas, comparando-se os compósitos híbridos e os reforçados somente com polpa. No processo de sucção e prensagem, embora útil para ajustes na formulação e na cura do compósito híbrido, não se percebeu contribuição estatisticamente significativa da celulose nanofibrilada na formação de pontes de transferência de tensões, e, portanto sem o correspondente aumento na resistência mecânica dos compósitos. Nos compósitos extrudados, a celulose nanofibrilada atuou de modo a melhorar o comportamento mecânico do compósito híbrido em comparação ao compósito sem nanofibras. Esta melhoria pode estar associada à maior adesão entre as nanofibrilas e a matriz cimentícia, o que foi atestado pela análise microestrutural (MEV) dos compósitos. Após o envelhecimento acelerado os compósitos com e sem nanofibras produzidos pelos dois processos não apresentaram redução do desempenho mecânico, o que se atribui à menor alcalinidade provida pela carbonatação acelerada. / Low elastic modulus vegetable fibers are known for their ability to increase the energy absorbed by cement based materials while they are loaded, especially during the post-crack stage. The use of cellulose nanofibers may contribute for toughening of brittle matrices and improving particle packing by both pore refining and crack intercepting at nanoscale, with the corresponding energy absorption. Nanofibrillated cellulose comes from a natural, abundant and renewable resources, it has good mechanical peformance and high specific surface, which contributes to improve the adhesion between the cement particles. These factors justify the use of nanofibrillated cellulose and give rise to an alternative nanoreinforcement for cement based materials. Thus, the aim of this work was the production of the nanofibrillated cellulose from bamboo organosolv pulp, establishing the best condition for its production and subsequent use as reinforcement in hybrid composites (both nano and micro-scale reinforcement) compared to composites reinforced with only microfibers (pulp), produced by the slurry vacuum dewatering followed by pressing and extrusion methods. The nanofibrillated cellulose was produced submitting unbleached and bleached pulps to 5, 10, 15 and 20 nanofibrillated cycles by the grinding method. Chemical, physical and mechanical tests were carried out to define the optimal condition to nanofibrillation. The unbleached nanofibrillated cellulose produced by 10 cycles was defined as the best option to be used in hybrid composites, since their greater modulus of elasticity and, because of their greater structural chemical stability, higher resistance to degradation in alkaline environments. The composites were subjected to accelerated carbonation curing process to mitigate thedegradation of fiber by reducing the matrix pH and also to refine the pores. The composites were subjected to accelerated aging process by means of 200 wet and dry cycles to assess their degradation. The hybrid composites and the composites reinforced only with pulp at 28 days and after accelerated aging were subjected to physico-mechanical and microstructural tests to study the effect of the nanofibrillated cellulose on their properties. There was no difference in the physical properties of the hybrid composites and composites reinforced with only pulp, produced by the two processes at 28 days. For the slurry vacuum dewatering followed by pressing process, although useful for adjustments in the formulation and cure hybrid composite, there was no statistically significant contribution of the nanofibrillated cellulose in the formation of stress transfer bridges, and therefore without a corresponding increase in the mechanical strength of the composites. For the extruded composites, the nanofibrillated cellulose improved the mechanical behavior of the hybrid composite compared to the composite without nanofiber. This improvement may be associated with greater adherence between the nanofibrils and the cement matrix, which was confirmed by microstructural analysis (SEM) of the composites. After accelerated aging, the composites with and without nanofibers produced by the two processes showed no reduction in mechanical performance, which is attributed to the lower alkalinity provided by the accelerated carbonation.

This thesis deals with processing of nanocellulose originating from pulps, with focus on mechanical pulp fibres and fines fractions. The nanocellulose materials produced within this research project were tested for different purposes ranging from strength additives in paper and paperboard products, via composite films to foam materials. TAPPI (Technical Association of Pulp &amp; Paper Industry) has recently suggested a standard terminology and nomenclature for nanocellulose materials (see paper I). In spite of that we have decided to use the terms nano-ligno-cellulose (NLC), microfibrillated cellulose (MFC), nanofibrillated cellulose (NFC) and nanocellulose (NC) in this thesis . It is well-known that mainly chemical pulps are used as starting material in nanocellulose production. However, chemical pulps as bleached sulphite and bleached kraft are quite expensive. One more cost-effective alternative can be to use fibres or fines fractions from thermo-mechanical pulp (TMP) and chemi-thermomechanical pulp (CTMP).   In paper II-IV, fractionation has been used to obtain fines fractions that can easily be mechanically treated using homogenisation. The idea with this study was to investigate the possibility to use fractions of low quality materials from fines fractions for the production of nanocellulose. The integration of a nanocellulose unit process in a high-yield pulping production line has a potential to become a future way to improve the quality level of traditional products such as paper and paperboard grades.   Paper III describes how to utilise the crill measurement technique as a tool for qualitative estimation of the amount of micro- and nano-material produced in a certain process. The crill values of TMP- and CTMP-based nanocelluloses were measured as a function of the homogenisation time. Results showed that the crill values of both TMP-NLC and CTMP-NLC correlated with the homogenisation time. In Paper V pretreating methods, hydrogen peroxide and TEMPO are evaluated. Crill measurement showed that hydrogen peroxide pretreatment (1% and 4%) and mechanical treatment time did not improve fibrillation efficiency as much as expected. However, for TEMPO-oxidised nanocelluloses, the crill value significantly increased with both the TEMPO chemical treatment and mechanical treatment time. In paper V-VII TEMPO-mediated oxidation systems (TEMPO/NaBr/NaClO) are applied to these fibres (CTMP and Sulphite pulp) in order to swell them so that it becomes easy to disrupt the fibres into nanofibres with mechanical treatment.   The demand for paperboard and other packaging materials are steadily increasing. Paper strength properties are crucial when the paperboard is to withstand high load. A solution that are investigated in papers IV and VI, is to use MFC as an alternative paper strength additive in papermaking. However, if one wish to target extremely higher strength improvement results, particularly for packaging paperboards, then it would be fair to use MFC or cationic starch (CS). In paper VI CS or TEMPO-based MFC was used to improve the strength properties of CTMP-based paperboard products. Results here indicate significant strength improvement with the use of different levels of CS (i.e., 20 and 10 kg t–1) and 5% MFC. The strengthening impact of 5% MFC was approximately equal to that of 10 kg t–1 of CS.   In paper VII, NFC and nanographite (NG) was used when producing composite films with enhanced sheet-resistance and mechanical properties. The films produced being quite stable, flexible, and bendable. Realising this concept of NFC-NG composite film would create new possibilities for technological advancement in the area of high-yield pulp technology.  Finally, in paper VIII, a new processing method for nanocellulose is introduced  where an organic acid (i.e., formic acid) is used. This eco-friendly approach has shown to be successful, a nanocellulose with a uniform size distribution has been produced. / <p>Vid tidpunkten för disputationen var följande delarbeten opublicerade: delarbete 5 och 7 inskickade, delarbete 6 och 8 manuskript.</p><p>At the time of the doctoral defence the following papers were unpublished: paper 5 and 7 submitted, paper 6 and 8 manuscripts.</p>

Les nanocelluloses connaissent un fort développement depuis ces dernières décennies et font l’objet de nombreuses études menées par les industriels et/ou consortiums académiques. Cette étude s’insère dans le cadre d’un projet européen (SUNPAP) visant à l’industrialisation des nanofibrilles de cellulose (NFC). La présente thèse fait l’état de nouveaux procédés de modification chimique de surface des NFC dans une optique de chimie verte. Plusieurs stratégies ont été développées telle que l’emploi de liquides ioniques comme solvant de réaction (décrit comme solvants verts) ou l’utilisation d’une nanoemulsion en phase aqueuse permettant le greffage de surface des NFC. Dans le but d’étudier l’impact de ces modifications chimiques, les substrats ainsi traités ont été par la suite utilisés dans diverses applications. Ainsi, des bionanocomposites ont pu être produits, l’impact sur l’introduction de NFC (modifiées ou non) dans du papier a également été étudié. Une étude sur les propriétés antibactériennes et la biodégradabilité des NFC modifiées est également proposée. Une caractérisation approfondie des NFC vierges et modifiées a été réalisée. Des techniques puissantes et innovantes ont été utilisées pour caractériser ces substrats tels que l’XPS (X-ray Photoelectron Spectroscopy) ou encore la SIMS (Secondary Ion Mass Spectrometry). Toutes ces modifications, applications et caractérisations proposées constituent une avancée et des perspectives prometteuses dans le monde des nanocelluloses. / Nanocelluloses know a strong interest since last decades and they are the subject of many studies led by industrials and / or academic consortia. This study is a part of a European project (SUNPAP) for the industrialization of nanofibrillated cellulose (NFC). This thesis is the state of new methods for the chemical surface modification of NFC with a view of green chemistry. Several strategies have been developed such as the use of ionic liquids as reaction solvent (described as green solvents) or the use of an aqueous medium in order to graft the surface of NFCs. Thus, the treated substrates were then used in various applications. Also, bionanocomposites were produced, the impact of the introduction of NFC (modified or not) in paper sheets has also been studied. A study on the antibacterial properties and biodegradability of modified NFC is also proposed. Several characterizations of neat and modified NFC were performed. Powerful and innovative techniques have been used to characterize these substrates such as XPS (X-ray Photoelectron Spectroscopy) or SIMS (Secondary Ion Mass Spectrometry). All these chemical modifications, applications and characterizations are offered promising prospects in the world of nanocelluloses.

Abstract Cellulose micro- and nanofibrils are elongated, flexible nano-scale particles produced from natural fibres with intensive mechanical treatments, usually in the form of dilute aqueous suspensions. Due to the recalcitrant structure of the fibres, mechanical, chemical and enzymatic pre-treatments are often used to loosen the fibre wall structure so as to facilitate the mechanical liberation of micro- and nanofibrils and reduce the high amount of mechanical energy needed. However, it is still unclear how different chemistries affect the disintegration phenomena and how mechanical action starts to unravel the fibre structure, and thus how micro- and nanofibrillation could best benefit from the pre-treatments. In addition, the high water content used in the process increases the production and transportation costs of the material, so that the solids content should be increased. Reducing the water content before or after production would be challenging, however, due to changes in fibre properties during drying (hornification) and the tendency for the resulting nanofibrils to agglomerate. Also, the effect of high solids content and temperature on the reduction of fibres to nano- and microfibrils is still not well understood. The aims of this work were to follow the changes in fibre morphology after mechanical, chemical and thermal modification and address their effects on the disintegration phenomena of the fibres to microfibrils. Mechanical compression-shearing, two selective oxidations and thermal drying in combination with TEMPO oxidation were used to modify the fibre structure before mechanical disintegration in a high-shear homogenizer or ball mill. The results showed that sufficient swelling of the fibre cell walls was a prerequisite for successful microfibrillation. Swelling can be promoted by loosening the hydrogen bonding network with compression and shearing forces or by increasing the charge density. Different charge thresholds were observed for microfibrillation depending on the chemistry used. Extremely hornified fibres were also successfully microfibrillated with the aid of TEMPO oxidation. Different fibre disintegration mechanisms were seen depending on the modification type and disintegration conditions. In addition, micro- and nanofibrils and nanocrystals were successfully produced under high solids (≥ 50%) conditions. / Tiivistelmä Luonnonkuiduista saatavat selluloosamikro- ja -nanofibrillit ovat pitkiä ja joustavia nanokokoluokan partikkeleita, joita valmistetaan yleensä intensiivisillä mekaanisilla käsittelyillä vesiliuoksissa. Kuitujen lujan rakenteen vuoksi valmistuksessa käytetään usein mekaanisia, kemiallisia ja entsymaattisia esikäsittelyjä heikentämään kuituseinämän tiivistä rakennetta, mikä helpottaa mikro- ja nanofibrillien irtoamista kuituseinämästä, sekä alentaa valmistuksen mekaanisen energian tarvetta. On kuitenkin edelleen epäselvää, miten erilaiset kemialliset käsittelyt vaikuttavat kuitujen hajoamiseen, miten kuiturakenne alkaa purkautua mekaanisessa käsittelyssä ja miten esikäsittelyillä voitaisiin parhaiten edistää mikro- ja nanofibrilloitumista. Valmistuksessa käytettävä korkea vesipitoisuus lisää mikro- ja nanofibrillien valmistus- ja kuljetuskustannuksia. Vesipitoisuuden alentaminen valmistuksessa tai sen jälkeen on kuitenkin haastavaa, sillä kuituominaisuudet muuttuvat kuivatuksessa ja valmiit nanofibrillit kimppuuntuvat helposti. Korkean kuiva-ainepitoisuuden ja lämpötilan vaikutusta kuidun hajoamiseen mikro- ja nanofibrilleiksi ei myöskään ymmärretä vielä täysin. Työn tarkoituksena oli tutkia sellukuitujen rakenteen muutoksia mekaanisen, kemiallisen ja lämpömuokkauksen seurauksena, sekä tutkia niiden vaikutusta kuidun purkautumiseen mikrofibrilleiksi. Kuiturakennetta muokattiin puristus-hiertomenetelmällä, kahdella selektiivisellä hapetusmenetelmällä, sekä lämpökuivauksen ja nk. TEMPO-hapetuksen yhdistelmällä ennen kuitujen mekaanista hajottamista joko leikkaavassa homogenisaattorissa tai kuulamyllyssä. Tulosten perusteella riittävä kuituseinämän turvottaminen oli edellytys onnistuneelle mikrofibrilloinnille. Turpoamista saatiin edistettyä hajottamalla kuiduissa olevia vetysidosverkostoja puristus- ja leikkausvoimilla tai kasvattamalla anionisen varauksen määrää kuiduissa. Varauksen kynnysarvo mikrofibrilloitumiselle riippui käytetystä hapetusmenetelmästä. Myös kuivatuksessa erittäin sarveistuneet kuidut saatiin mikrofibrilloitua TEMPO-hapetuksen avulla. Tulosten perusteella kuiduilla on erilaisia hajoamismekanismeja, jotka riippuvat käytetystä muokkauksesta, sen intensiivisyydestä, sekä hajottamisolosuhteista. Työssä onnistuttiin myös valmistamaan mikro- ja nanofibrillejä, sekä nanokiteitä tavanomaista huomattavasti korkeammassa (≥50 %) kuiva-ainepitoisuudessa.

L'objectif de cette thèse est la préparation d’aérogels biosourcés ayant des propriétés de super-isolation thermique. Pour cela, nous avons choisi de développer de nouveaux aérogels à base de nanofibres de cellulose (NFC). Les aérogels ont été préparés par lyophilisation. Dans un premier temps, une analyse des paramètres expérimentaux jouant un rôle sur la morphologie et les propriétés physico-chimiques des aérogels a été réalisée afin d’obtenir les meilleures propriétés d’isolation thermique. Avec une suspension de NFC à 2% en masse, sans ajout de sels et sans faire varier le pH, une lyophilisation réalisée dans des moules d’aluminium à une température de -80°C a permis d’obtenir des aérogels ayant une conductivité thermique de 0,024 W/m.K. Afin de diminuer cette conductivité thermique, nous avons choisi de réduire la taille des pores pour obtenir un effet Knudsen. Pour cela, une nouvelle technique de séchage a été proposée : la lyophilisation par pulvérisation. Les aérogels préparés dans les mêmes conditions expérimentales que précédemment avec cette technique ont des propriétés thermiques super-isolantes (0,018 W/m.K) grâce à la nano-structuration du réseau poreux. Finalement, un nouveau dispositif expérimental a été développé pour caractériser plus finement les propriétés thermiques des aérogels. C’est un dispositif transitoire impulsionnel qui permet d'estimer simultanément la contribution de la conduction solide et gazeuse, l'effet radiatif et la diffusivité thermique grâce à un modèle théorique simple. Ce dispositif permettra d’approfondir l’étude complexe du transfert thermique à travers des matériaux poreux semi-transparents tels que les aérogels. / The objective of this thesis is the preparation of renewable aerogels having thermal super-insulating properties. To do it, we designed new aerogels from nanofibrillated cellulose (NFC) by freeze-drying. This technique is simple and has the advantage of not using organic solvents. First of all, the parameters playing a role on the aerogel morphology and physico-chemical properties of the aerogels were analyzed to get the best thermal insulating properties. Using 2 wt% NFC suspensions, without addition of salts, keeping the initial pH, the obtained freeze-dried aerogels in alumina molds at -80 °C have a thermal conductivity of 0.024 W/m.K. In order to reduce the pore size and to improve the thermal insulating properties by Knudsen effect, a new drying technique was proposed: the spray freeze-drying. Aerogels prepared in the same experimental conditions with this technique have thermal super-insulating properties (0.018 W/m.K) thanks to the nanostructuration of the porous network. Finally, a new device was designed to characterize more precisely the thermal properties of aerogels. This is an impulsive transient device, which can estimate simultaneously the contribution of solid and gas conduction, the radiative effect and thermal diffusivity using a simple theoretical model. This device will allow studying complex heat transfer through porous semi-transparent materials such as aerogels

[pt] A busca por materiais que não impactem negativamente o meio ambiente tem sido uma das prioridades de engenheiros que trabalham com materiais de construção. A emissão expressiva de CO2 na produção de cimento contribui para tal preocupação. Dentro deste cenário, soluções com emprego de nanotecnologia vêm chamando a atenção em diversas áreas por proporcionar novas soluções. O principal objetivo da presente tese é associar um material proveniente de uma fonte natural com benefícios provenientes da nanotecnologia a fim de modificar propriedades de pastas de cimento considerando seus aspectos químicos, físicos e mecânicos. A nanocelulose se apresenta como material proveniente de fonte renovável que apresenta propriedades atraentes aos materiais cimentícios, sendo assim uma opção a ser utilizada em conjunto com o cimento. Dentre os diversos tipos disponíveis, a celulose nanofibrilada (CNF) foi elencada para ser investigada neste trabalho. A celulose microcristalina (CMM) foi incluída nas investigações para possibilitar uma comparação direta entre as fibrilas da CNF e as partículas de CMM. O uso desses materiais celulósicos pode ser considerado recente e, com isso, existem ainda lacunas no que tange o entendimento dos seus efeitos em materiais cimentícios. Assim, a viabilidade da CNF e da CMM enquanto reforços em pastas de cimento foi avaliada por meio de ensaios de compressão e flexão. Os possíveis mecanismos responsáveis pelo efeito de ambas CMM e CNF foram estudados por meio de análises químicas e físicas. Por fim, foi realizada a caracterização das pastas reforçadas quanto à retração, total e autógena, e à reologia, nos regimes estático e dinâmico. Por conta dos impactos na trabalhabilidade promovidos pela inclusão de CNF, a mistura delas nas pastas de cimento foi facilitada com a adição de superplastificante, especialmente em porcentagens maiores que 0.050 por cento, em peso. A CMM e a CNF se mostraram eficazes em reforçar as pastas de cimento quanto a esforços de flexão e tração, levando ao aumento das respectivas resistências e módulos. Os resultados obtidos mostraram que a água presente no gel da CNF não está totalmente disponível como água de mistura por conta da morfologia e hidroficilidade das fibrilas. Observada uma certa combinação de porcentagem e fator água-cimento, a inclusão de CNF diminuiu a retração autógena das pastas. A inclusão de 0,040 por cento de NFC levou a resultados semelhantes aos da adição de CMM referente ao aumento da tensão de escoamento e da viscosidade. / [en] The seek for low environmental impact materials has become one of the priorities of construction building materials engineers. One of the reasons is the massive growing contribution of cement production industry in worldwide CO2 emissions. In this scenario, the dissemination of nanotechnology into varied areas is drawing attention for enabling new possibilities. The idea of the present thesis is to associate a material provided from a natural source with the potential benefits of nanotechnology to modify conventional cement pastes regarding their chemical, physical and mechanical aspects. Nanocellulose arises as an alternative that meets an eco-friendly source with remarkably properties expected from nanomaterials. There are different types of nano cellulosic materials that may be tailored to achieve desired compatibilities with varied cementitious materials. In this work, nanofibrillated cellulose (NFC) in the form of gel, and microcrystalline cellulose (MCC) particles were investigated, so a comparison could be traced between them. The use of both NFC and MCC in cementitious materials is recent and there are important gaps regarding their effect. For that reason, the feasibility of MCC and NFC to act as reinforcement on cement pastes was evaluated through compressive and flexural tests. Then, the possible mechanisms behind the effect of MCC and NFC on the microstructure of cement pastes were investigated through distinct chemical and physical analyses. Moreover, the total and autogenous shrinkage were characterized, as well as the dynamic and static rheological behaviors. Due to rheological modifications, the mixture of cement pastes with NFC was facilitated by a superplasticizer, especially for percentages higher than 0.050 percent wt. The MCC and NFC promoted the reinforcement of the cement pastes, regarding flexural and tensile stresses, increasing the composite strength and modulus. It was observed that he water present in the NFC gel is not totally available as mixing water due to the morphology and hydrophilicity of the fibrils. If associating certain levels of inclusions and water ratio, the NFC inclusion led to a decrease in autogenous shrinkage. The addition of 0.040 percent of NFC resulted in similar outcomes to 1.000 percent of MCC regarding their ability to increase yield stress and viscosity.

This work describes three alternative processes for producing microfibrillated cellulose (MFC; also referred to as cellulose nanofibrils, CNF) in which bleached pulp fibres are first pretreated and then homogenized using a high-pressure homogenizer. In one process, fibre cell wall delamination was facilitated by a combined enzymatic and mechanical pretreatment. In the two other processes, cell wall delamination was facilitated by pretreatments that introduced anionically charged groups into the fibre wall, by means of either a carboxymethylation reaction or irreversibly attaching carboxymethylcellulose (CMC) to the fibres. All three processes are industrially feasible and enable energy-efficient production of MFC. Using these processes, MFC can be produced with an energy consumption of 500–2300 kWh/tonne. These materials have been characterized in various ways and it has been demonstrated that the produced MFCs are approximately 5–30 nm wide and up to several microns long. The MFCs were also evaluated in a number of applications in paper. The carboxymethylated MFC was used to prepare strong free-standing barrier films and to coat wood-containing papers to improve the surface strength and reduce the linting propensity of the papers. MFC, produced with an enzymatic pretreatment, was also produced at pilot scale and was studied in a pilot-scale paper making trial as a strength agent added at the wet-end for highly filled papers. / <p>QC 20150126</p>