Biopharmaceuticals, including proteins, DNA and vaccines, are one of the fastest growing segments of the overall pharmaceutical market. While the hypodermic injection, the most common delivery method for these molecules, is effective, it also has limitations, including low patient compliance, need for medically trained personnel and biohazardous sharps after delivery. The overall goal of this thesis was to develop a new delivery system for biopharmaceuticals, based on dissolving polymer microneedles, which is effective and more patient compliant than the hypodermic needle. Microneedles are microscopic needles that are large enough to insert into the skin to deliver drugs effectively, while being short enough to avoid the pain causing nerves deep in the skin. An additional benefit of polymer microneedles is that the needles completely dissolve in the skin, leaving behind no biohazardous sharps. There are significant material and fabrication issues that must be overcome in the development of this new device. The first part of this thesis focused on the development of a new fabrication process, based on in situ photopolymerization, for the creation of polymer microneedles. These microneedles were shown to successfully insert into the skin, dissolving within a minute to deliver the encapsulated cargo, and retain full activity of encapsulated proteins. Next, we applied the microneedle technology to the delivery of the influenza virus. We found that the reformulation process required to encapsulate the influenza virus in polymer microneedles did not affect the antigenicity or immunogenicity of the virus. In addition, we used coated metal microneedles to successfully immunize mice with the influenza virus, verifying the delivery capabilities of a microneedle system. Finally, we used the dissolving polymer microneedles to successfully immunize mice with the influenza virus, resulting in full protection against lethal challenge after one immunization. This immune response was equivalent to the control intramuscular injection. In conclusion, we have developed dissolving polymer microneedles as an effective and patient compliant delivery system for biopharmaceuticals. This system could be especially applicable to mass immunization efforts or home use, since it can be self-administered and allows for easy disposal with no biohazardous sharps.

La réalisation de revêtements fins, solides et isolants dans le domaine ultrasonore,contenant de petites particules poreuses, représente le challenge de ces travaux. Plusieurs points sont déterminants pour arriver à cet objectif final. Tout d’abord, il faut trouver le matériau adéquat pour les particules poreuses, notre choix s’est porté sur un polymère mou, le PEG-DA. Une fois le matériau choisi, il faut déterminer une voie de synthèse pour en faire un matériau poreux, une technique par photopolymérisation UV etpar dissolution d’un porogène sacrificiel (CaCO3) a été utilisée. Ensuite, la microfluidiquenous a permis de réaliser des microparticules de ce polymère poreux de tailles contrôlées et monodisperses. La dernière étape consiste à disperser ces particules dans une matrice pour en faire un revêtement. Les mesures acoustiques ont montré une bonne atténuation du PEG-DA dans les ultrasons.Par ailleurs, ces travaux ont permis d’étudier la photopolymérisation frontale de milieux transparents et très diffusants, et de présenter une méthode à partir de simulations Monte-Carlo pour décrire les profils de conversion du polymère en fonction de l’intensité initiale et de l’épaisseur traversée. D’autres études se sont focalisées sur le séchage d’hydrogels de PEG-DA et sur la dissolution de CaCO3 à travers ces mêmes hydrogels. Un modèle physique décrivant la compétition entre cinétique de dissolution et diffusion de l’acide a été proposé. / The fabrication of thin, solid and insulating coatings containing small porous particles is the major challenge of these works. Several key points need to be raised to succeed. First, a good material for the particles has to be found, we chose a soft polymer, PEG-DA. Then, the choice of the synthesis routine to make porous polymers is crucial. A technique using UV photopolymerization and dissolution of sacrificial porogen (CaCO$_3$) will be used. Next, we will decide to make porous particles by microfluidics to obtain well controlled sizes and good monodispersity. The last step will be about the dispersion of those particles in a matrix to create coatings. Acoustics measurements will show the acoustic response of PEG-DA in ultrasounds. Moreover, this work will also permit us to study the frontal photopolymerization of transparent and scattering media and to present a method with Monte-Carlo simulations to describe conversion profiles of polymer as a function of intensity and path length. Other studies will present drying of PEG-DA hydrogels and dissolution of CaCO$_3$ through those hydrogels. A physical model will be proposed to describe the competition between kinetics and acid diffusion.

Este trabalho demonstra o uso da fotopolimerização via absorção de dois fótons na produção de microestruturas dopadas com compostos orgânicos e nanopartículas de Au. A capacidade de produção de microestruturas com propriedades variadas é extremamente relevante, pois viabiliza o desenvolvimento de uma nova geração de dispositivos ópticos. Além disso, realizamos a conexão entre as microestruturas fabricadas e fontes de excitação, por meio de nanofibras de vidro. A integração entre essas estruturas, e destas com meios externos de excitação e detecção, é um passo essencial para o desenvolvimento de microcircuitos fotônicos, que podem representar uma nova revolução tecnológica, a exemplo do que foram os microcircuitos eletrônicos. Exploramos as possibilidades de dopagem da resina usando: (i) um composto fluorescente, (ii) um composto com birrefringência fotoinduzida e (iii) nanopartículas de ouro. Microestruturas contendo Rodamina B apresentaram boa integridade estrutural e fluorescência, tendo sido usadas para demonstrar a conexão dos microelementos com meios externos de excitação. Através de nanofibras e de micromanipuladores, comprovamos a capacidade de excitação seletiva de microestruturas através do guiamento da luz de um laser de Ar+. Estruturas birrefringentes foram obtidas pela dopagem com o azopolímero HEMA-DR13. Montamos um aparato que permite a observação da dinâmica de indução de birrefringência nas microestruturas, o qual representa um grande passo na caracterização deste tipo de microelementos. Com base nesse estudo, foi possível alcançar uma fração de birrefringência residual nas microestruturas de 35%. Por fim, propomos um método para a dopagem de microestruturas poliméricas com nanopartículas de ouro. Por se tratar de um método de dopagem indireta, ele evita interferências das nanopartículas no processo de microfabricação. Dessa forma, este trabalho abre possibilidades para a fabricação de microdispositivos funcionais com diversas propriedades especiais, bem como a integração desses microdispositivos em circuitos fotônicos. / This work demonstrates the use of two-photon photopolymerization in the fabrication of microstructures doped with organic compounds and gold nanoparticles. The ability to produce microstructures with different properties is extremely relevant, because it opens the possibility for the development of a new generation of optical devices. Besides, we have accomplished the connection between fabricated microstructures and excitation sources by means of silica nanowires. The connection among structures and with external means of detection and excitation is an essential step towards the development of new technological breakthrough in photonic microcircuits. We have explored the resin doping possibilities by using: (i) a fluorescent compound, (ii) a photoinduced birefringent compound and (iii) gold nanoparticles. Rhodamine B doped microstructures present good structural integrity and fluorescence, and were able to demonstrate the connection of microelements with external means of excitation. Through the use of nanofiber tapers and micromanipulators, we have shown the selective excitation capability of this method by guiding Ar+ laser light onto one single microstructure. Birefringent samples were obtained by doping the resin with the azopolymer HEMA-DR13. We have assembled an apparatus that allows observing the photoinduced birefringence dynamics, which represents a great step towards a better characterization of these kinds of microelements. Based on this study we were able to achieve a residual birefringence fraction of 35% in microscopic samples. Finally, we have proposed a new method for the doping of polymeric microstructures with gold nanoparticles. Because it is an indirect doping technique, it prevents gold nanoparticles from interfering with the microfabrication process. Thus, the work presented here paves the way for the fabrication of functional microdevices with a wide range of special properties, as well as for the connection of these microstructures for photonic microcircuit.

Microestruturas poliméricas dopadas despertam grande interesse nas áreas de óptica, fotônica e biologia, pois viabilizam a produção de dispositivos com propriedades específicas. Contudo, a dopagem de microestruturas com mais de um dopante é pouco explorada na literatura. Nesse contexto, o presente trabalho propõe o desenvolvimento de uma metodologia para fabricar microestruturas poliméricas com múltiplas dopagens, através de fotopolimerização por absorção de dois fótons. Esta técnica de microfabricação faz uso de um feixe laser pulsado (Ti:safira, 780 nm, 100 fs) que é focalizado, através de lentes de microscópio, no volume de uma resina polimérica contendo fotoiniciador composto orgânico responsável por iniciar o processo de polimerização. A intensidade dos pulsos de femtossegundos é alta o bastante para que processos não lineares absorcivos, nesse caso absorção de dois fótons, ocorram apenas no volume focal, induzindo a polimerização apenas ao seu redor. Como dopantes utilizamos os corantes fluorescentes Rodamina e Fluoresceína. Para averiguar a eficácia do sistema de fabricação desenvolvido, produzimos estruturas com apenas um dopante, e as caracterizamos utilizando microscopia óptica e eletrônica. Microestruturas contendo mais de um dopante, em regiões distintas, foram produzidas através da fabricação sequencial de estruturas dopadas. Essa metodologia permite a produção de estruturas com dupla dopagem, as quais apresentam boa integridade estrutural e preservam as propriedades ópticas dos dopantes. Por fim, visando aplicações em biologia, empregamos a metodologia desenvolvida para fabricar microambientes dopados, em sítios específicos, com o antibiótico cloridrato de ciprofloxacino. Estudos iniciais do desenvolvimento da bactéria Escherichia coli nestes microambientes foram feitos, com o objetivo de demonstrar a viabilidade para este tipo de aplicação. / Doped microstructures have attracted interest in optics, photonics and biology, because they allow the production of devices with specific proprieties. However, doping microstructures with more than one dopant is not much exploited in the literature. In this work we demonstrate the development of a method to fabricate multi-doped microstructures by two-photon absorption polymerization. For the microfabrication we used a femtosecond laser (Ti:sapphire laser, 780 nm, 100 fs) that is focused, by a microscope objective, in the volume of a polymeric resin containing a photoinitiator organic compound responsible to initiate the polymerization. The intensity of the femtosecond pulses is high enough to induced two-photon absorption, and consequently polymerization, only around the focal volume. As dopants we employed the fluorescent dyes Rhodamine and Fluorescein. In order to verify the microfabrication system, we have initially fabricated microstructures with only one dopant, which were characterized using optical and electron microscopies. Microstructures containing more than one dopant, in distinct regions, were produced by sequential fabrication of single doped structures. Such method allowed the fabrication of double doped structures, which presents good structural integrity and maintain the characteristic optical properties of the dyes. Finally, aiming at biological applications, we employed the developed method to fabricate micro-environments doped, in specific sites, with the antibiotics ciprofloxacin hydrochloride. Initial studies on the growth of the bacterium Escherichia coli, on such microstructures, were carried out to demonstrate the feasibility for such type of application.

Foram realizadas análises por espectros absorção, fluorescência e excitação para anilina e orto-toluidina em água, com e sem a adição de HCl. Os resultados indicam que as propriedades do meio dependem das concentrações de amina e de HCl, sendo observado principalmente pelos espectros de excitação de fluorescência. Espectros de 1H RMN parecem indicar um efeito de agregação destas moléculas pelas mudanças observadas na forma e na posição dos sinais dos prótons. Foi realizada a síntese de polianilina e de poli-o-toluidina, sendo o acompanhamento efetuado por espectroscopia ultravioleta-visível e pela técnica de perfil de potencial, indicando similaridades entre os dois métodos. As sínteses de polianilina e de poli-o-toluidina também foram realizadas via fotoquímica, sendo os produtos de reação caracterizados por espectroscopia ultravioleta visível e por infravermelho. / The aim this work was to study aniline and orto-toluidine in aqueous solution with or without HCl addition. The analyses were realized by absorption and fluorescence spectrum. The results show that the proprieties are relation on amines and chloridric acid concentrations, especially it was observed by fluorescence excitation spectrum. Changes in protons sign position and in the form can be indicating an effect of aggregation with these molecules though 1H RMN spectrum. UV-Vis spectroscopy and open circuit potential measurements were used for monitor the synthesis of polyaniline and the poly-o-toluidine. Theses methods show similar results. Also, the synthesis of polyaniline and the poly-o-toluidine were realized by photochemistry via, which the reaction products were characterized by UV-Vis spectroscopy and FTIR.

Les travaux décrits dans cette thèse portent sur la synthèse ainsi que l’étude physico-chimique et photo-chimique de plusieurs séries de nitroxydes et d’alcoxyamines photosensibles fonctionnalisées par des chromophores de type benzophénone, fluorènone, anthraquinone, phényle, naphtyle et anthracényle. En particulier, nous avons focalisé notre effort sur l’introduction de ces chromophores sur un nitroxyde dérivé d’un noyau isoindoline connu pour sa stabilité photo-chimique. L’étude de la photo-dissociation des alcoxyamines préparées a ensuite été conduite par résonance paramagnétique électronique. Les résultats obtenus mettent en évidence deux nouvelles classes d’alcoxyamines photosensibles qui présentent une efficacité remarquable de photo-dissociation homolytique pour donner les radicaux nitroxyle et alkyle correspondant sous UV et irradiation de lumière visible. En effet, les alcoxyamines de type naphtyle et anthraquinone ont donné des rendements de dissociation homolytique quantitatifs sous irradiation UV et visible, et ce, quel que soit le fragment alkyle libéré (i.e. styryle, méthacrylyle, acrylyle). De plus, nous avons également montré que les nitroxydes portant les chromophores naphtyle et anthraquinone présentent une stabilité photochimique élevée. Ainsi, l’analyse de ces résultats suggère que les alcoxyamines dérivées de ces deux nitroxydes présentent toutes les caractéristiques requises pour être des candidats performants en photopolymérisation radicalaire contrôlée en présence de nitroxydes. / The work reported herein details the synthesis, as well as the photophysical and photochemical analysis, of novel unsubstituted benzophenone-, methoxy substituted benzophenone-, pyrrolidine substituted benzophenone-, fluorenone-, anthraquinone-, phenyl-, naphthyl- and anthracenyl-based photosensitive alkoxyamines for potential application in nitroxide-mediated photopolymerization.The high photochemical stability of the isoindoline class of nitroxide was exploited within the structural design. Fusion of the isoindoline motif into the examined chromophores facilitated efficient energy transfer between chromophore and alkoxyamine motifs, whilst exerting minimal influence on the photophysical properties of the investigated chromophores. Photochemical investigation of the examined alkoxyamines highlighted two new classes of photosensitive alkoxyamines which displayed highly desirable photo-dissociation efficiencies to afford nitroxide and alkyl radicals under UV and visible light irradiation. Specifically, styrenic, methacrylic and acrylic naphthyl-based alkoxyamines, as well as, styrenic and methacrylic anthraquinone-based alkoxyamines demonstrated near quantitative yields of photo-dissociation under UV and visible light irradiation respectively. The high yields of photo-dissociation obtained for the naphthyl- and anthraquinone-based systems, as well as the high photochemical stability of their corresponding nitroxides, indicate these new classes of photosensitive alkoxyamines are highly relevant candidates for further investigation within a photopolymerization context.

Ce manuscrit est consacré à l'élaboration de phases stationnaires monolithiques organiques pour lesmicrosystèmes électrochromatographiques plastiques. La partie bibliographique situe d'abord l'intérêt destechniques électrocinétiques en microsystème. Ensuite, l'état de l'art sur l'utilisation des monolithes dans cestechniques séparatives est présenté en portant une attention particulière à la description du processus dephotopolymérisation. La fonctionnalisation de surface du copolymère d'oléfine cyclique (COC) est ensuitedétaillée afin d'envisager l'ancrage du monolithe aux parois du canal.La partie expérimentale a porté tout d'abord sur le développement et la caractérisation de deux monolithesacrylates dédiés à la chromatographie à polarités des phases inversées. Le travail expérimental s'est ensuiteorienté vers le développement d’un nouveau procédé permettant la synthèse et l’ancrage du monolithe dansles microcanaux en COC, ceci en une seule étape et à partir des photoinitiateurs de type I. Ce protocolepermet l'obtention d'efficacités intéressantes qui restent cependant inférieures à celles obtenues en capillaire.Des adaptations des conditions d'irradiation ont alors été apportées pour la synthèse de ces monolithes àl’intérieur des microsystèmes afin d'obtenir des efficacités de l’ordre de 250 000 plateaux/m. Pour terminer,les domaines d'applications et la longévité du dispositif ont été illustrés par la séparation de différentesfamilles de solutés (PAH, mycotoxines, catécholamines, acides aminés, amines biogènes) et l'analysed'échantillons réels tels que les vins (pour déterminer la teneur en certaines amines biogènes : histamine ettyramine). / This manuscript is dedicated to the synthesis of organic monolithic stationary phases in plasticelectrochromatographic microchips. The bibliography part shows the benefit of electrokinetic techniques formicrosystems. After an overview on the use of monoliths in separation techniques, the manuscript is focusedon the description of photopolymerization process. Finally, a detailed review of the different protocols offunctionnalization of cyclic olefin copolymer (COC) surface to allow anchoring of the monolith to thechannel walls is produced.The experimental study firstly deals with the development and characterization of two acrylate monolithsdedicated to the reversed phase mode in chromatography. Then, the experimental part focus on a new onestepmethod for the simultaneous synthesis and anchoring of organic monolith inside COC microchipchannel, thanks to the use of type I photoinitiators. This protocol improves efficiencies which neverthelessstay below those obtained in capillary. Further, the adjustment of the irradiation conditions allows to reachup to 250 000 plates/m. Finally, the field of applications and the durability of microsystem have beenillustrated by the separation of different kinds of solutes (HAP, mycotoxins, catecholamines, biogenicamines) and the analysis of real matrices such as wine samples (for the quantitative determination of twobiogenic amines : histamine and tyramine).

La première synthèse d'un carbène N-hétérocylique borane (NHC-borane) stable a été réalisée en 1993. Pourtant la découverte de leur vaste potentiel en chimie n'a réellement débuté qu'à partir de 2007. Les domaines d'application de ces composés du bore, stables et facile d'accès, s'étendent de la synthèse d'organique (réduction d'imine, hydroboration de liaisons multiples, médiateurs radicalaires) à la chimie organométallique (couplage de Suzuki-Miyaura) en passant par la chimie des polymères (amorceurs ou co-amorceurs de photopolymérisation). L'objectif de ce projet aura été d'étendre l'application des NHC-boranes dans deux différents systèmes de photopolymérisation. Le premier système étudié a permis l'obtention de matériaux acrylates contenant des nanoparticules métalliques à partir d'un seul composé dans un processus monotope. Le second système visait l'amorçage de réactions de polymérisation en émulsion sous irradiation visible. Nous avons utilisé le pouvoir réducteur des NHC-boranes pour former des nanoparticules d'or ou d'argent directement dans des monomères acrylates. Puis, la formation par le NHC-borane de la matrice polymère contenant les nanoparticules est déclenchée par une irradiation UV. L'analyse par HRTEM a mis en évidence des petites nanoparticules (ca. 10 nm) emprisonnées dans la matrice. Cette méthode présente une approche encore plus directe pour obtenir ce type de matériau plutôt que les procédés multi-étapes déjà existants. Le second système étudié utilise pour la première fois un NHC-borane comme co-amorceur de la polymérisation du styrène ou du méthacrylate de méthyle en émulsion sous irradiation visible. Il en résulte des latex stables, composés de particules de tailles moyennes contrôlées formés à partir de quantités de tensioactifs inférieures à celles utilisées dans des systèmes photoamorcés déjà décrits. Ces systèmes amorcés par une irradiation visibles pourraient être intéressants pour réduire les coûts énergétiques des synthèses et éviter la dégradation de composés thermo- ou UV- fragiles / Despite the first synthesis of stable N-heterocyclic carbene (NHC)-boranes occurring as early as 1993, the widespread exploration of their potential in chemistry truly began only in 2007. The versatility of these stable and easily accessible boron compounds has led to their application in organic reactions (imine reduction, multiple bond hydroboration, radical reductions), organometallic reactions (Suzuki- Miyaura cross coupling) and polymerization (initiation or co-initiation of polymerization). The aim of my project was to extend the applicability of NHC-boranes to two different photopolymerization systems. The first aimed to synthesize polymer matrices containing metal nanoparticles in a one pot, one reactant process. The second aimed to perform emulsion polymerizations initiated by visible light. In the first system, the reductive capacity of NHC-boranes was used to generate gold or silver nanoparticles directly in acrylate monomers. Then, the initiating ability of NHC-boranes was triggered by UV light to form the polymer matrix containing embedded nanoparticles. Characterization by HRTEM showed small nanoparticles (ca. 10 nm) successfully contained within the matrix. This method represents a more straightforward approach than obtaining such materials through the multistep processes already reported in literature. In the second system, NHC-boranes were employed for the first time as co-initiators in visible light initiated emulsion polymerization styrene and methyl methacrylate. Stable latexes were generated with controllable particle sizes at lower surfactant concentrations than those used in related light-initiated systems. Such visible light-triggered initiation systems are interesting for reducing energy consumption and avoiding degradation of heat- or UV-sensitive materials

Polymer brush patterns were prepared by a combination of electron beam induced damage in self-assembled monolayers (SAMs), creating a stable carbonaceous deposit, and consecutive self-initiated photografting and photopolymerization (SIPGP). This newly applied technique, reactive writing (RW), is investigated with 1H,1H,2H,2H-perfluorooctyltriethoxysilane SAM (PF-SAM) on silicon oxide, which, when modified by RW, can be selectively functionalized by SIPGP. With the monomer N,N-dimethylaminoethyl methacrylate (DMAEMA), we demonstrate the straightforward formation of polymer brush gradients and single polymer lines of sub-100 nm lateral dimensions, with high contrast to the PF-SAM background. The lithography parameters acceleration voltage, irradiation dose, beam current and dwell time were systematically varied to identify the optimal conditions for the maximum conversion of the SAM into a carbonaceous deposit. The results of this approach were compared to patterns prepared by carbon templating (CT) under analogous conditions, revealing a dwell time dependency, which differs from earlier reports. This new technique expands the range of CT by giving the opportunity to not only vary the chemistry of the created polymer patterns with monomer choice but also vary the chemistry of the surrounding substrate.

Independent control of the surface and bulk properties is advantageous for many applications such as adhesives, release coatings, and antimicrobial films. Traditional methods for achieving independent control typically require multiple processing steps such as wet-on-wet or wet-on-dry coating methods. Independent control over the surface properties can achieved in a single step utilizing the temporal and spatial control inherent to photopolymerization. Specifically, a co-photopolymerization of monomers with different reactivities in the presence of a light gradient is capable of producing a polymer film with a surface chemistry that differs from the bulk chemistry. The light gradient, produced via the concentration of photoinitiator in the formulation, results in a reaction gradient through the film with the higher rates of reaction occurring in the high light intensity regions of the film. The preferentially reacting monomer adds at a greater rate in the high light intensity regions resulting in non-uniform consumption yielding a concentration gradient. Consequently, diffusion of the preferentially reacting monomer from the bulk to the surface of the film and a counter-diffusion of the other monomer from the surface to the bulk of the film occurs from the non-uniform monomer consumption thus producing a film with a concentration gradient through the depth of the film with the preferentially reacting monomer enriching the high light intensity regions. A variety of kinetic differences capable of producing a stratified film will be presented including inherent monomer reactivity, number of functional groups per monomer, oxygen inhibition, thiol-ene chemistry, and Norrish type two initiation. Additionally, parameters that control the degree of stratification, such as methods of varying polymerization rate and the light gradient, will be examined. Changes in surface properties (such as contact angle, surface hardness, adhesion) and bulk properties (such as mechanical properties measured by dynamic mechanical analysis and polymer swelling) are studied as a function of stratification. Finally, a mathematical model which describes and predicts the production of stratified films via photopolymerization is presented. Photopolymerization allows for a facile, single step method of generating stratified films with controllable surface chemistries.