京都大学 / 新制・課程博士 / 博士(工学) / 甲第24849号 / 工博第5166号 / 新制||工||1987(附属図書館) / 京都大学大学院工学研究科機械理工学専攻 / (主査)教授 泉井, 一浩, 教授 松原, 厚, 教授 平山, 朋子 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

Laser powder bed fusion (LPBF) is a popular additive manufacturing (AM) technique that has demonstrated the capability to produce sophisticated engineering components. This work reports the crack-free fabrication of an SS316L/IN718 bimetallic structure via LPBF, along with compositional redistribution, phase transformations and microstructural development, and nanohardness variations. Constituent intermixing after LPBF was quantitatively estimated using thermo-kinetic coefficients of mass transport and compared with the diffusivity of Ni in the austenitic Fe-Ni system. The intermixing of primary solvents (Ni and Fe) in SS316L/IN718 bimetallic structures was observed for an intermixing zone of approximately 800 µm, and their intermixing coefficient was estimated to be in the order of 10−5 m2/s based on time of 10 ms. In addition, to understand the high temperature behavior, SS316L/IN718 bimetallic structures were annealed at 850, 950, and 1050 °C, for 120, 48, and 24h respectively, followed by water quenching (WQ). Furthermore, to better understand the intermixing of individual components (Ni and Fe) and to predict the varying (maximum) temperatures in LPBF of SS316L/IN718 bimetallic structures, solid-to-solid SS316L vs IN718 diffusion couples were examined at 850, 950, and 1050 °C, for 120, 48, and 24h respectively, followed by WQ. The investigation of SS316L vs IN718 diffusion couples yielded a maximum temperature of approximately 3400 K in the LPBF of SS316L/IN718 bimetallic structures. Finally, compositional redistribution, phase transformations and microstructural development, and nanohardness variations after LPBF of SS316L/IN625 bimetallic structure were also investigated to provide a better understanding of the LPBF process via bimetallic fabrication.

Heat exchangers are integral parts for thermal management and find countless applications in automotive, aerospace, energy, nuclear power plants, HVAC, etc. Due to intensive research & development and technological advancements in manufacturing technologies, there is an increasing rise in demand for high-performance heat exchangers. In the automotive and aerospace industries, heat exchangers are expected to deliver better thermal efficiency and improve the system’s overall functionality in which they are installed by saving space and being lightweight. Additive Manufacturing (AM) is a ground-breaking and promising technology that offers avenues of opportunities to manufacture parts that were almost impossible to be produced with conventional manufacturing and can improve part performance with lightweight and compact designs. Laser-Based Powder Bed Fusion (LPBF), one of the well-known AM techniques, provides freedom to design complex geometries and fabricate them in a layer-by-layer fashion by exposing a high-density laser on a vertically moving powder bed. The study focuses on the application of AM in re-designing heat exchangers under given design requirements using LPBF. It includes exploring Triply Periodic Minimal Surfaces (TPMS) based structures such as gyroid and realizing them as heat exchanger core. Computational gyroid-based heat exchanger core models were designed and analyzed for thermal and fluid dynamics characteristics. A parametric study and analysis based on gyroid TPMS network type, periodic length, thickness, aspect ratio, and functional grading were carried out to optimize heat exchanger performance as per design conditions and validate their manufacturability using LPBF. Successful printable designs were further used to develop and manufacture prototypes. The study concludes with a comparison between additively manufactured gyroid-based design and conventional shell-and-tube design based on the thermal performance from CFD analysis and the weight of prototypes. It was found that the thermal performance from CFD analysis showed an 18.96% improvement, whereas weight was reduced by 14.8% for the gyroid-based design as compared to the conventional shell-and-tube design. / Thesis / Master of Applied Science (MASc)

Laser Powder Bed Fusion (L-PBF) is a metal additive manufacturing technique that uses a laser beam as a heat source to melt metal powder selectively. Because of the process small layer thicknesses, laser beam diameter, and powder particle size, L-PBF allows the fabrication of novel geometries and complex internal structures with enhanced properties. However, the main disadvantages of the L-PBF process are high costs and a lengthy production time. As a result, shortening the manufacturing process while maintaining comparable properties is exceptionally beneficial. Inconel 625 (IN625) is a nickel-based superalloy becoming increasingly popular in marine, petroleum, nuclear, and aerospace applications. However, the properties of IN625 parts produced by casting or forging are challenging to control due to their low thermal conductivity, high strength and work hardening rate, and high chemical complexity. Furthermore, IN625 alloy is regarded as a difficult-to-machine material. As a result, it is worthwhile to seek new technologies to manufacture complex-shaped IN625 parts with high dimensional accuracy. IN625 alloy is known for its excellent weldability and high resistance to hot cracking; thus, IN625 alloy appears to be a promising candidate for additive manufacturing. This thesis presents an experimentally focused study on optimizing L-PBF processing parameters in IN625 superalloy to increase process productivity while maintaining high material density and hardness. This study had four stages: preliminary, exploratory, modelling, and optimization. The first stage was devoted to conducting a literature review and determining the initial processing parameters. The second stage concentrated on determining the process window, for which single tracks were printed with two high levels of laser power (300, 400 W), five levels of scan speed (500, 700, 900, 1100, 1300 mm/s), and five levels of powder layer thickness (30, 60, 90, 120, 150 µm). Then, the process window was defined after investigating the top views and cross-sections of the tracks. Stage 3 involved printing 48 cubes (10 × 10 × 10 mm^3) with a laser power of 400 W, scan speeds of (700, 900, 1100, 1300 m/s), layer thicknesses of (60, 90, 120, 150 µm), and overlap percentages of (10, 30, 50%). As a result, the density of cubes was measured, and a statistical multiple regression analysis was used to predict it. Stage 4 involved estimating four sets of ideal processing parameters (based on statistical modelling of relative density) and printing 24 cubes (10 × 10 × 10 mm^3), six samples for each set. Finally, the relative density, hardness, and productivity of the samples were assessed, and a trade-off was determined. Even with the thickest powder layer of 150 µm (highest process productivity), samples with a mean relative density greater than 99% (i.e., 99.31% by Archimedes principle and 99.82% by image analysis) were printed. These findings are consistent with previously published results for L-PBF IN625 samples manufactured with smaller layer thicknesses ranging from 20 to 40 µm while maintaining comparable material hardness. The findings of this study are noteworthy because IN625 parts can be printed with higher powder layer thicknesses (less production time) while retaining similar material properties to those published with typical layer thicknesses ranging from 20 to 40 µm. Reduced production time due to optimized processing parameters can lead to significant energy and cost savings. / Thesis / Master of Applied Science (MASc)

No description available.

Laser powder bed fusion is a type of metal-based additive manufacturing method that can be customized for a given material through modification of process parameters, resulting in changes to the overall quality and mechanical properties of the as-built component. Optimal mechanical properties are typically achieved by performing experimental builds of fully dense components with multiple parameter sets and comparing the resulting mechanical properties. Additionally, AM allows geometric freedom that can be utilized to produce structures tailored for energy absorption, such as cellular structures or lattice structures. There is limited previous work of scaling effects on mechanical properties of cellular structures. The first part of this work aims to determine process parameters that result in the best overall mechanical properties of L-PBF manufactured maraging 300 steel. This work then uses the optimal parameters to produce cellular structures scaled both uniformly and selectively to perform mechanical and physical analysis on their response.

This thesis explores the optimization of process parameters for producing single-track thin walls using Laser Powder Bed Fusion (LPBF) additive manufacturing. Using two different coupon designs, the study assesses the feasibility of creating the thinnest possible leak-tight structures within LPBF and evaluating their mechanical properties, including burst pressure and modulus of elasticity under pressure loads. A series of experimental iterations were conducted, varying laser power and laser speed to identify optimal conditions. The findings indicate that a narrow range of process parameters can produce consistently leak-tight thin walls. The results contribute to understanding how to achieve high quality, reliable thin wall structures in the LPBF process, with implications for industrial applications requiring thin, precise, leak tight, and durable walls.

There is an upsurge of research interest on Alloy 718 additively manufactured (AM) by electron beam powder bed fusion (EB-PBF) technique in aero and land-based gas turbine engines. However, the surface quality of the manufactured components has always been a major challenge. Several factors, including powder particle size, layer thickness, beam parameters, scanning strategies, and inclination angle of the build, govern the surface characteristics. Along with surface roughness resulted from partially melted powder particles, surface defects such as balls, satellites, microcracks as well as up-skin and down-skin surfaces can enhance the vulnerability of the manufactured parts to corrosion. When the surface is unable to withstand the exposed environment adequately, corrosion can be triggered. The surface-induced corrosion failures are increasingly becoming more challenging as the AM components often have complex geometries that render them even more difficult to finish. So, the relatively poor surface finish is the barrier to the full exploitation of the AM industry. In the present study, to achieve the desired surface quality, hence an improved high temperature corrosion performance, shot peening was implemented on Alloy 718 parts manufactured by EB-PBF. The high temperature corrosion behavior of the parts was investigated in an ambient air environment at 650 and 800 °C for up to 336 h. The underlying physical and chemical factors at play of the parts exposed to the corrosive environment were investigated too. The effect of topographical features (e.g., surface roughness) and microstructural characteristics (e.g., grain structure, phases, and defects) on high temperature corrosion behavior were analyzed by 3D surface profilometry, hardness test, optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy disperse spectroscopy (EDS), X-ray diffractometry (XRD) and electron backscatter diffraction (EBSD). The surface roughness and high temperature corrosion rate of the parts was significantly reduced after shot peening.

This thesis work was done to get a fundamental knowledge of the mechanical and microstructural properties of 316L stainless steel fabricated with the additive manufacturing technique, laser powder-bed fusion (L-PBF). The aims of the thesis were to study the mechanical and microstructural properties in two different building orientations for samples built in two different machines, and to summarize mechanical data from previous research on additive manufactured 316L. Additive manufacturing (AM) or 3D-printing, is a manufacturing technique that in recent years has been adopted by the industry due to the complexity of parts that can be built and the wide range of materials that can be used. This have made it important to understand the behaviour and properties of the material, since the material differs from conventionally produced material. This also adds to 316L, which is an austenitic stainless steel used in corrosive environments. To study the effect of the building orientation, samples of 316L were built in different orientations on the build plate. The density and amount of pores were also measured. Tensile testing and Charpy-V testing were made at room temperature. Vickers hardness was also measured. Microstructure and fracture surfaces were examined using light optical microscope (LOM) and scanning electron microscope (SEM). The microstructure of the 316L made with L-PBF was found to have meltpools with coarser grains inside them, sometime spanning over several meltpools. Inside these coarser grains was a finer cellular/columnar sub-grain structure. The tensile properties were found to be anisotropic with higher strength values in the orientation perpendicular to the building direction. Also high dense samples had higher tensile properties than low dense samples. The impact toughness was found to be influenced negatively by high porosity. Hardness was similar in different orientations, but lower for less dense samples. Defects due to lack of fusing of particles were found on both the microstructure sample surfaces and fracture surfaces. The values from this study compare well with previous reported research findings.

Additive manufacturing (AM) is a promising manufacturing process that provides that ability to fabricate components with complex geometries with relatively low lead times compared to other manufacturing processes. This allows for more freedom of design, as prototypes can easily be produced throughout the development process. AM is also especially beneficial in tooling applications, where internal geometries such as cooling channels are required in order to improve the quality of the manufactured parts. These geometries are more difficult to produce with more conventional manufacturing methods such as forging or casting. Currently, Laser Powder Bed Fusion (LPBF) shows the most promise in the field of Additive Manufacturing (AM) of metals, as it offers the freedom to produce complex components with little post processing required. Additionally, post processing with Hot Isostatic Pressing (HIP) can be implemented to significantly enhance the final properties of the material.  The LPBF-process can produce many different defects within the parts such as: part porosity and lack of fusion. This is mainly due to the layer-by-layer configuration of the process. Parts can also experience large thermal fluctuations and rapid cooling rates which can generate large residual stresses. This can result in significant cracking in certain high alloyed materials which can impact part quality and  material properties. If the cracking is severe enough, it will result in failure of the entire component and render the entire parts completely useless. Post processing with HIP may remove some of these defects and reduce the residual stresses in the material and thus produce a material with properties that are satisfactory. The purpose of this thesis is to investigate the processability of a high alloy cold work tool steel with LPBF. The main focus is the influence of the processing parameters and part geometry on the quality of the produced parts. Furthermore, the influence of the processing parameters on defects and microstructure will also be investigated. The aim is to produce parts that can be enhanced with HIP as a post processing treatment. Additionally, the impact of HIP on the properties of the part will also be investigated in order to determine if the there are any improvements in terms ofreduction in part defects and the removal of any undesired microstructural features which are produced from the process. The experimental results showed that the processability of the tool steel is difficult. Several sample volumes were produced with varying processing parameters and scanning strategies, and all the specimens from all sample volumes exhibited some cracking. Parts produced with a combination of contouring and hatching strategy, where there is an internal structure showed the most promise, as these parts exhibited the least amount of severe cracking. However, additional research of the processing parameters and scanning strategies is required in order to reduce the amount of cracking of the external shell structure and thus, achieve proper densification of the parts when post processing with HIP. / Additiv tillverkning (AM) är en lovande tillverkningsprocess som ger möjligheten att tillverka komponenter med komplexa geometrier med relativt låga ledtider jämfört med andra tillverkningsprocesser. Detta ger större frihet i under designprocessen eftersom prototyper enkelt kan produceras under hela utvecklingsprocessen. AM är också särskilt fördelaktigt i verktygstillämpningar, där interna geometrier såsom kylkanaler krävs för att förbättra kvaliteten på de tillverkade delarna. Dessa geometrier är svårare att tillverka med mer konventionella tillverkningsmetoder som smidning eller gjutning. För närvarande visar det sig att Laser Powder Bed Fusion (LPBF) är det mest lovande inom området additiv tillverkning av metaller, eftersom processen erbjuder friheten att producera komplexa komponenter samt att efterbearbetning som krävs blir mindre. Dessutom kan efterbearbetning med Hot Isostatic Pressing (HIP) implementeras för att avsevärt förbättra materialets slutliga egenskaper. LPBF-processen kan ge upphov till många olika defekter i delarna såsom: delporositet och lack of fusion. Detta beror främst på att processen sker lagervis vilket kan ge upphov att många småfel. Delar kan också uppleva stora termiska fluktuationer och snabba kylningshastigheter som kan generera stora restspänningar. Det kan resultera i stor sprickbildning i vissa höglegerade material vilket kan påverka delarnas kvalitet och materialegenskaper. Om sprickorna som bildas är stora eller djupa nog kommer detta att resultera i att hela komponenten blir oanvändbar. Efterbearbetning med HIP kan ta bort en del av dessa defekter och minska restspänningarna i materialet och därmed producera ett material med goda egenskaper. Syftet med detta arbete är att undersöka bearbetbarheten hos ett höglegerat kallbearbetningsstål med som produceras med LPBF. Huvudfokus är påverkan av processparametrar och detaljgeometrin på kvaliteten på de producerade delarna. Vidare kommer också processparametrarnas inverkan på defekter och mikrostruktur att undersökas. Syftet är att producera delar som kan förbättras med HIP som efterbehandlingsbehandling. Dessutom kommer effekterna av HIP på delens egenskaper också att undersökas för att avgöra om det finns några förbättringar i termer av minskning av deldefekter och avlägsnande av alla oönskade mikrostrukturella egenskaper som produceras från processen. De experimentella resultaten visade att verktygsstålets bearbetbarhet är svår. Flera provvolymer producerades med varierande processparametrar och skanningsstrategier, och alla prover från alla provvolymer uppvisade viss sprickbildning. Delar som tillverkats med en kombination av kontur och hatch, där det finns en inre struktur visade sig mest lovande, eftersom dessa delar uppvisade minst sprickbildning. Ytterligare arbete av processparametrarna och skanningsstrategier krävs dock för att minska mängden sprickbildning i den yttre skalstrukturen och därmed uppnå korrekt förtätning av delarna vid efterbearbetning med HIP.