Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: One of the main challenges in using the Discrete Element Method (DEM) is to specify the correct input parameter values. In general, the models are sensitive to the input parameter values and accurate results can only be achieved if the correct values are specified. For the linear contact model, micro parameters such as the particle density, stiffness, coefficient of friction, as well as the particle size and shape distributions are required. Thus, there is a need for a procedure to accurately calibrate these parameters before any attempt can be made to accurately model a complete bulk materials handling system. Since the DEM is often used to model applications in the mining and quarrying industries, a calibration procedure was developed for materials that consist of relatively large (up to 40 mm in size) particles. A coarse crushed aggregate was used as the test material. Using a specially designed large scale shear box, the confined Young’s Modulus and internal friction angle of the material were measured by means of the confined compression test and the direct shear test respectively. The bulk (macro) density and porosity were also measured. The particle size distribution was measured while visual inspection was used to identify the different particle shapes. DEM models of the experimental set-up were developed and the input parameter values were varied iteratively until a close correlation between the experimental and numerical results was achieved. The resulting set of input parameter values were then verified through a series of anchor pull-out and angle of repose experiments and simulations. A good correlation between the experimental and numerical results was observed. In a study, independent of the calibration process, a half fraction factorial design was implemented to quantify the effect of the input parameter values on the bulk properties and to construct multiple linear regression models that relate the parameters to the bulk properties. The results were found to be in accordance with expected bulk behaviour, and can be used to develop advanced DEM calibration strategies. Based on the project outcomes, it was concluded that the developed calibration procedure performed satisfactorily and that the calibrated input parameters allow for the accurate modelling of the coarse aggregate. / AFRIKAANSE OPSOMMING: Een van die groot uitdagings in die gebruik van die Diskreet Element Metode (DEM) is om die korrekte invoer parameterwaardes te spesifiseer. Die modelle is in die algemeen sensitief vir die invoer parameterwaardes, en akkurate resultate kan slegs verkry word indien die korrekte waardes gespesifiseer word. Mikroparameters soos partikeldigtheid, styfheid, wrywingskoëffisiënt, die partikelgrootte verspreiding asook die partikelvorm verspreiding, word benodig vir die lineêre kontakmodel. ’n Prosedure word dus benodig om hierdie parameters akkuraat te kalibreer alvorens ’n volledige korrelagte materiaalhanteringstelsel akkuraat gemodelleer kan word. Aangesien die DEM gereeld in die modellering van myn- en gruisgroefbedryf toepassings gebruik word, is ’n kalibrasieprosedure ontwikkel vir materiaal wat bestaan uit relatief groot (tot 40 mm in grootte) partikels. Grofgebreekte klippe is as toetsmateriaal gebruik. Deur gebruik te maak van ’n spesiaal ontwerpte grootskaal-skuifboks is die ingeperkte Young se Modulus en die interne wrywingshoek van die materiaal gemeet deur middel van die ingeperkte kompressietoets en die direkte skuiftoets onderskeidelik. Die makro-digtheid en poreusheid is ook gemeet. Die partikelgrootte verspreiding is gemeet terwyl visuele inspeksie gebruik is om die verskillende partikelvorms te identifiseer. DEM modelle van die eksperimentele opstelling is ontwikkel en die invoer parameterwaardes is herhaaldelik gewysig totdat ’n goeie korrelasie verkry is tussen die eksperimentele en numeriese resultate. Die gevolglike stel invoer parameterwaardes is daarna geverifieer deur ’n reeks ankeruittrek- en natuurlike helling eksperimente en simulasies. In ’n studie, onafhanklik van die kalibrasieproses, is die half-fraksie faktoriaalontwerp geïmplementeer om die invoer parameterwaardes se effek op die makro eienskappe te kwantifiseer en om meervoudige lineêre regressiemodelle te ontwikkel wat die parameters met die makro eienskappe verbind. Die resultate was in ooreenstemming met die verwagte makro gedrag en kan gebruik word om gevorderde DEM kalibrasie-strategieë te ontwikkel. Daar is tot die gevolg gekom dat, gebaseer op die projekresultate, die ontwikkelde kalibrasieprosedure bevredigend presteer en dat die gekalibreerde invoer parameters die akkurate modellering van die grofgebreekte klippe toelaat.

The Warsaw Quarries of Coshocton County, Ohio, virtually ignored since Holmes' landmark papers of 1919, are investigated to achieve several goals: 1) to create a revised general typology of the material culture of bedded-chert lithic procurement sites; 2) to demonstrate that the occurrence of radiocarbon samples at lithic procurement sites is the norm rather than the exception; 3) to clarify the nature of activity at the site through a synthesis of functional and attribute analyses of material recovered from a peripheral spoils ridge; 4) to demonstrate that data collected at procurement sites by surface collection constitutes an insufficient database for analysis; 5) to test an hypothesis that the presumed absence of classic site elements (stratigraphy, diagnostic artifacts, dateable material) is incorrect. Since the completion of late 19`h and early 20`h century work in the field, analysis of quarry sites in North America has been limited to sporadic and usually very subject-specific research. By neglecting to evaluate the overall nature and function of lithic procurement sites, recent work has relegated lithic procurement to a sub-field of only secondary interest to archaeologists. / Department of Anthropology

Stone is a useful resource, for example as a building material, which means that stone materials play a large role in the construction of society. Stone is mined and refined in so-called quarries. There are activities in quarries that have negative impact on the environment. In addition, such industries have traditionally consumed a substantial amount of fossil fuel. Due to these aspects, among others, the quarrying industry should become more sustainable.  Circular economy has the fundamental idea of reducing, reusing and recycling, and can be useful for improving sustainability. To make a business more sustainable, all parts of it should improve in this aspect, including the processes. Process improvement is a strong area of the Lean, which strives to create flow and to remove everything that interferes with the flow. The purpose of the study was to obtain a deeper understanding of how quarries can be improved from a sustainability perspective with a combination of circular economy and Lean. This by reviewing previous theory of sustainability, circular economy, Lean and other relevant areas. The study was carried out as a qualitative case study at, and in collaboration with, a quarrying company in Sweden. The data collection consisted of interviews with relevant people from the company and observations of quarries. The results were compared with the theoretical framework to answer the formulated research questions. The study resulted in several conclusions, the most fundamental is that increased awareness and knowledge about sustainability would bring better possibilities for the company in its work towards a more sustainable busiss. According to the company investments must yield economic profitability, and hence a large responsibility is laid on the customers to demand sustainable products.  Permissions and regulations are, according to the interviewees, obstacles to increased recycling of stone materials, and consequently obstacles to circular economy. An adjustment of permissions to allow more reuse of materials would benefit circular economy. Lean is not entirely applicable due to the long lead times in quarries. However, some aspects of Lean are useful, especially its focus on minimizing wastes. An approach characterized by a circular mindset and by process improvement can be adopted with a combination of circular economy and Lean. Overall, quarrying needs to be seen from a holistic perspective and the communication between all parties in the distribution chain needs to be improved.

published_or_final_version / Architecture / Master / Master of Landscape Architecture

Not available / text

This project examines opportunities for history exhibition design practices. Research into museum studies and creative work in typography, photography, graphic design and architecture result in curation and design of a prototypical exhibit about the granite quarrying industry of Stonington, Maine.

Economic development is one of the main objectives of developed and developing nations worldwide. Development comes with growth of urban areas. Urban growth is achieved through sand and gravel mining for construction of modern, attractive and durable structures. The study examined positive and negative environmental impacts of the continuous removal of river sand, pit sand and gravel from sampled rivers and open areas surrounding Gaborone developing Central Business District, malls and private properties in city. Quantitative and qualitative research designs that is questionnaire survey, oral interviews, field observation and measurements were used to collect data from selected sampled points. Metsimotlhabe and Ditlhakane rivers were selected because they are nearer to Gaborone and most river sand is mined from these rivers. More points were sampled from open areas in Kumakwane, Kopong and Bela Bela farms where pit sand and gravel are mined. Convenience and purposive sampling methods were used to pick questionnaire survey respondents (175) from Kumakwane and Metsimotlhabe villages where people affected lives. Findings of the study highlighted that river sand was mined most from rivers near Gaborone compared to pit sand and gravel because of its multi uses. Mining is important for economic development, to construct durable, modern structures, employment creation and revenue collection but removal of river sand leads to deepening and widening of rivers. Artificial rivulets are formed as resource is extracted uncontrollably. Pit sand and gravel are extracted from open areas creating uncovered deep pits, which caused of accidents to children and livestock. Erosion and environmental degradation occur due to continuous mining. Miners dispose waste on open areas and riverbeds causing land pollution. Dust and noise pollution from tipper trucks ferrying sand and gravel are a cause of concern to villagers as the trucks move even at night, disturbing sleep. Solutions to uncontrolled mining include 24 hour security and regular raids on illegal miners. The author recommends that heavy penalties should be imposed to curb illegal mining. High level decision making forum involving all stakeholders is necessary to discuss problems of illegal mining and how to limit negative impacts. Department of Mines need to develop an Environmental Management Plan and a close monitoring program nationwide. / Environmental Sciences / M. Sc. (Environmental Management)

Economic development is one of the main objectives of developed and developing nations worldwide. Development comes with growth of urban areas. Urban growth is achieved through sand and gravel mining for construction of modern, attractive and durable structures. The study examined positive and negative environmental impacts of the continuous removal of river sand, pit sand and gravel from sampled rivers and open areas surrounding Gaborone developing Central Business District, malls and private properties in city. Quantitative and qualitative research designs that is questionnaire survey, oral interviews, field observation and measurements were used to collect data from selected sampled points. Metsimotlhabe and Ditlhakane rivers were selected because they are nearer to Gaborone and most river sand is mined from these rivers. More points were sampled from open areas in Kumakwane, Kopong and Bela Bela farms where pit sand and gravel are mined. Convenience and purposive sampling methods were used to pick questionnaire survey respondents (175) from Kumakwane and Metsimotlhabe villages where people affected lives. Findings of the study highlighted that river sand was mined most from rivers near Gaborone compared to pit sand and gravel because of its multi uses. Mining is important for economic development, to construct durable, modern structures, employment creation and revenue collection but removal of river sand leads to deepening and widening of rivers. Artificial rivulets are formed as resource is extracted uncontrollably. Pit sand and gravel are extracted from open areas creating uncovered deep pits, which caused of accidents to children and livestock. Erosion and environmental degradation occur due to continuous mining. Miners dispose waste on open areas and riverbeds causing land pollution. Dust and noise pollution from tipper trucks ferrying sand and gravel are a cause of concern to villagers as the trucks move even at night, disturbing sleep. Solutions to uncontrolled mining include 24 hour security and regular raids on illegal miners. The author recommends that heavy penalties should be imposed to curb illegal mining. High level decision making forum involving all stakeholders is necessary to discuss problems of illegal mining and how to limit negative impacts. Department of Mines need to develop an Environmental Management Plan and a close monitoring program nationwide. / Environmental Sciences / M. Sc. (Environmental Management)

No description available.