O objetivo do estudo foi avaliar ex vivo a influência da aplicação do laser de Er:YAG na parede dentinária de raízes fragilizadas, reforçadas com resina composta. Cinquenta caninos superiores tiveram suas coroas removidas próximo da junção amelo-cementária e incluídas em bloco de resina acrílica. Após tratamento endodôntico foi realizada a fragilização das raízes. Os espécimes foram distribuídos aleatoriamente em 5 grupos (n=10),: Grupo I - não irradiado, tratado com ácido fosfórico 37%; Grupo II - irradiado com laser Er:YAG, 300mJ - 10 Hz; Grupo III - irradiado com laser Er:YAG, 300mJ - 10 Hz e tratado com ácido fosfórico 37% ;Grupo IV - irradiado com laser Er:YAG, 500mJ - 10 Hz; Grupo V - irradiado com laser Er:YAG, 500mJ - 10 Hz e tratado com ácido fosfórico 37%. Todos os espécimes receberem reforço intra-radicular com resina composta, foto-polimerizada por meio de pino foto-transmissor. No espaço promovido por este pino foi cimentado o pino metálico pré-fabricado, com cimento resinoso auto-adesivo de dupla polimerização. Os espécimes foram submetidos ao teste de Tração na Máquina Universal de Ensaios - INSTRON 4444. Os maiores valores para o deslocamento foram atribuídos ao Grupo I, estatisticamente semelhante ao Grupo III. Entretanto o Grupo III ocupa uma posição intermediária, podendo pertencer também aos GruposIV e V que foram estatisticamente semelhantes entre si e ao grupo II. / The aim of this study was to assess ex vivo the effects of Er:YAG laser as dentin treatment of weakened root canal reinforced with composite resin. Fifty upper canines were decoronated at cementoenamel junction and the roots were embedded in acrylic resin. After the endodontic treatment the roots were weakened and the specimens were randomly assigned to five groups (n=10): Group I - unirradiated, treated with phosphoric acid 37%; Group II - Er:YAG laser 300mJ - 10Hz; Group III - Er:YAG laser 300mJ - 10 Hz, treated with phosphoric acid 37%; Group IV - Er:YAG laser 500mJ - 10 Hz; Group V - Er:YAG laser 500mJ - 10 Hz, treated with phosphoric acid 37%. The intraradicular reinforcement was made in all specimens with composite resin using photo-transmitter post, which creates a space for the insertion of prefabricated metal post. The metal posts were inserted using a resin cement self-adhesive dual-cured. The tensile bond strength of specimens was tested in a universal testing machine - INSTRON 4444. The results showed that Group I was statistically similar to the Group III and presented the highest bond strength values. Group III also showed statistical similarity with Group IV and V, which were similar among them and the Group II.

Failure criteria play a vital role in the numerical analysis of reinforced concrete structures. The current failure criteria can be classified into two types, namely the empirical and theoretical failure criteria. Empirical failure criteria normally lack reasonable theoretical backgrounds, while theoretical ones either involve too many parameters or ignore the effects of intermediate principal stress on the concrete strength. Based on the octahedral shear stress model and the concrete tensile strength under the state of triaxial and uniaxial stress, a new failure criterion, that is, the simplified unified strength theory (UST), is developed by simplifiing the five-parameter UST for the analysis of reinforced concrete structures. According to the simplified UST failure criterion, the concrete strength is influenced by the maximum and intermediate principal shear stresses together with the corresponding normal stresses. Moreover, the effect of hydrostatic pressure on the concrete strength is also taken into account. The failure criterion involves three concrete strengths, namely the uniaxial tensile and compressive strengths and the equal biaxial compressive strength. In the numerical analysis, a degenerated shell element with the layered approach is adopted for the simulation of concrete structures. In the layered approach, concrete is divided into several layers over the thickness of the elements and reinforcing steel is smeared into the corresponding number of layers of equivalent thickness. In each concrete layer, three-dimensional stresses are calculated at the integration points. For the material modelling, concrete is treated as isotropic material until cracking occurs. Cracked concrete is treated as an orthotropic material incorporating tension stiffening and the reduction of cracked shear stiffness. Meanwhile, the smeared craclc model is employed. The bending reinforcements and the stirrups are simulated using a trilinear material model. To verify the correctness of the simplified UST failure criterion, comparisons are made with concrete triaxial empirical results as well as with the Kupfer and the Ottosen failure criteria. Finally, the proposed failure criterion is used for the flexural analysis of simply supported reinforced concrete beams. Also conducted are the punching shear analyses of single- and multi-column-slab connections and of half-scale flat plate models. In view of its accuracy and capabilities, the simplified UST failure criterion may be used to analyse beam- and slab-type reinforced concrete structures.

The phenomenon called soil aggregate coalescence occurs at contact-points between aggregates and causes soil strength to increase to values that can inhibit plant root exploration and thus potential yield. During natural wetting and drying, soil aggregates appear to ‘weld’ together with little or no increase in dry bulk density. The precise reasons for this phenomenon are not understood, but it has been found to occur even in soils comprised entirely of water stable aggregates. Soil aggregate coalescence has not been widely observed and reported in soil science and yet may pose a significant risk for crops preventing them from achieving their genetic and environmental yield potentials. This project used soil penetrometer resistance and an indirect tensile-strength test to measure the early stages of aggregate coalescence and to evaluate their effects on the early growth of tomato plants. The early stages of aggregate coalescence were thought to be affected by a number of factors including: the matric suction of water during application and subsequent drainage, the overburden pressure on moist soil in the root zone, the initial size of soil aggregates prior to wetting, and the degree of sodicity of the soil aggregates. Seven mainexperiments were conducted to evaluate these factors. The matric suction during wetting of a seedbed affects the degree of aggregate slaking that occurs, and the strength of the wetted aggregates. The matric suction during draining affects the magnitude of ‘effective stresses’ that operate to retain soil structural integrity as the soil drains and dries out. An experiment was conducted to evaluate the influence of matric suction (within a range of suctions experienced in the field) on aggregate coalescence using soils of two different textures. Sieved aggregates (0.5 to 2 mm diameter) from a coarse-textured and two fine-textured (swelling) soils were packed into cylindrical rings (4.77 cm i.d., 5 cm high) and subjected to different suctions on wetting (near-saturation, and 1 kPa), and on draining (10 kPa on sintered-glass funnels, and 100 kPa on ceramic pressure plates). After one-week of drainage, penetrometer resistance was measured as a function of depth to approximately 45 mm (penetrometer had a recessedshaft, cone diameter = 2 mm, advanced at a rate of 0.3 mm/min). Tensile strength of other core-samples was measured after air-drying using an indirect “Brazilian” crushing test. For the coarse-textured soil, penetrometer resistance was significantly greater for samples wet to near-saturation, despite there being no significant increase in dry bulk density; this was not the case for the finer-textured soils, and it was difficult to distinguish the effects of variable bulk density upon drying from those of the imposed wetting treatments. In both coarse- and fine-textured soils, the tensile strength was significantly greater for samples wet to near-saturation. Thus wetting- and draining-suctions were both found to influence the degree of soil aggregate coalescence as measured by penetrometer resistance and tensile strength. Aggregate coalescence in irrigated crops is known to develop as the growing season progresses. It was therefore thought to be linked to the repeated occurrence of matric suctions that enhance the phenomenon during cycles of wetting and draining. An experiment was conducted to determine the extent of aggregate coalescence in a coarsetextured and two fine-textured (swelling clay) soils during 8 successive cycles of wetting and draining. Sieved aggregates (0.5 to 2 mm diameter) from each soil were packed into cylindrical rings (4.77 cm i.d., 5 cm high) and wetted to near saturation for 24 h. They were then drained on ceramic pressure plates to a suction of 100 kPa for one week, after which penetrometer resistance and tensile strength were measured as described above. The degree of expression of aggregate coalescence depended on soil type. For the coarse-textured soil, repeated wetting and draining significantly increased bulk density, penetrometer resistance and tensile strength. For the fine-textured soil, penetrometer resistance and bulk density did not vary significantly with repeated wetting and draining; on the contrary, there was evidence in these swelling clay soils to suggest bulk density and penetrometer resistance decreased. However, there was a progressive increase in tensile strength as cycles of wetting and draining progressed. The expansive nature of the fine-textured soil appears to have masked the development of aggregate coalescence as measured by penetrometer resistance, but its expression was very clear in measurements of tensile strength despite the reduction in bulk density with successive wetting and draining. Field observations have indicated that aggregate coalescence is first expressed at the bottom of the seedbed and that it develops progressively upward to the soil surface during the growing season. This suggests that overburden pressures may enhance the onset of the phenomenon by increasing the degree of inter-aggregate contact. Soils containing large quantities of particulate organic matter were known to resist the onset of aggregate coalescence to some extent. An experiment was conducted to evaluate the effects of soil organic matter and overburden pressures, by placing brass cylinders of various weights (equivalent to static load pressures of 0, 0.49, 1.47 and 2.47 kPa) on the top of dry soil aggregates (0.5 – 2 mm diameter) having widely different soil organic carbon contents placed in steel rings 5 cm high and 5 cm i.d. With the weights in place, the aggregates were wetted to near-saturation for 24 h and then drained on ceramic pressure plates to a suction of 100 kPa for one week. Bulk density, penetrometer resistance and tensile strength were measured when the samples were removed from the pressure plates and they all increased significantly with increasing overburden pressure in the soil with low organic matter content, but not in the soil with high organic matter content. The amount of tillage used to prepare seedbeds influences the size distribution of soil aggregates produced – that is, more tillage produces finer seedbeds. The size distribution of soil aggregates affects the number of inter-aggregate contact points and this was thought to influence the degree of aggregate coalescence that develops in a seedbed. Previous work has shown that soil organic matter reduces aggregate coalescence and so an experiment was conducted to evaluate the effects of aggregate size and organic matter on the phenomenon. For soils with high and low organic matter contents, aggregate size fractions of < 0.5, 0.5 – 2, 2 – 4, and < 4 mm were packed into soil cores (as above) and wetted to near-saturation then drained to 100 kPa suction as described above. Penetrometer resistance and tensile strength were measured and found to increase directly with the amount of fine material present in the soil cores – being greater in the < 0.5 mm and < 4 mm fractions, and being less in the 0.5 – 2 mm and 2 – 4 mm fractions. In all cases, penetrometer resistance and tensile strength were lower in the samples containing more organic matter. The rate at which soil aggregates are wetted in a seedbed affects the degree of slaking and densification that occurs, and the extent to which aggregates are wetted influences the overall strength of a seedbed. Both wetting rate and the extent of wetting were believed to influence the onset of aggregate coalescence and were thought to be affected by soil organic matter and irrigation technique. An experiment was therefore designed to separate these effects so that improvements to management could be evaluated for their greatest efficacy – that is, to determine whether management should focus on improving irrigation technique or increasing soil organic matter content, or both. The rate of wetting was controlled by spraying (or not spraying) soil aggregates (0.5 – 2 mm diameter) with polyvinyl alcohol (PVA). Samples of coarse- and fine-textured soils were packed into steel rings (as above) and subjected to different application rates of water (1, 10 and 100 mm/h) using a dripper system controlled by a peristaltic pump. Samples were brought to either a near-saturated state or to a suction of 10 kPa for 24 h, and then drained on a pressure plate at a suction of 100 kPa for one week. Measurements of penetrometer resistance and tensile strength were then made as described above. As expected, penetrometer resistance was lower in samples treated with PVA before wetting (slower wetting rates) and in samples held at a greater suction (10 kPa) after initial wetting (greater inter-aggregate strength). The effects were more pronounced in the coarse-textured soil. In both coarse- and fine-textured soils, tensile strengths increased with increasing wetting rate (greatest for 100 mm/h) and extent of wetting (greater when held at near-saturated conditions). The rate of wetting was found to be somewhat more important for promoting aggregate coalescence than the extent of wetting. Because aggregate coalescence often occurs with little or no increase in bulk density, an explanation for the increase in penetrometer resistance and tensile strength is unlikely to be explained by a large increase in the number of inter-aggregate contacts. An increase in the strength of existing points of inter-aggregate contact was therefore considered in this work. For inter-aggregate bond strengths to increase, it was hypothesized that small increases in the amount of mechanically (or spontaneously) dispersed clay particles, and subsequent deposition at inter-aggregate contact points could increase aggregate coalescence as measured by penetrometer resistance and tensile strength. An experiment was devised to manipulate the amount of spontaneously dispersed clay in coarse- and fine-textured soils of high and low organic matter content. The degree of sodicity of each soil was manipulated by varying the exchangeable sodium percentage (ESP) of soil aggregates (0.5 – 2mm) above and below a nominal threshold value of 6. Dry aggregates were then packed into steel rings (as above) and subjected to wetting near saturation, then draining to a suction of 100 kPa for one week as described above. Measurements were then taken of penetrometer resistance and tensile strength, both of which were affected by ESP in different ways. In the coarse-textured soil, sodicity enhanced aggregate slaking and dispersion, which increased bulk density. While penetrometer resistance also increased, its effect on aggregate coalescence could not be separated from a simple effect of increased bulk density. Similarly, the effect of sodicity on aggregate coalescence in the fine-textured soil was confounded by the higher water contents produced by greater swelling, which produced lower-than-expected penetrometer resistance. Measurements of tensile strength were conducted on air-dry samples, and so the confounding effects of bulk density and water content were eliminated and it was found that tensile strength increased with sodicity in both coarse- and fine-textured soils. The presence of dispersed clay was therefore implicated in the development of aggregate coalescence in this work. Finally, a preliminary evaluation of how the early stages of aggregate coalescence might affect plant growth was attempted using tomatoes (Gross lisse) as a test plant. Seeds were planted in aggregates (0.5 – 4 mm) of a coarse- or fine-textured soil packed in steel rings. These were wetted at a rate of 1 mm/h to either near-saturation (for maximum coalescence) or to a suction of 10 kPa (for minimum coalescence) and held under these conditions for 24 h. All samples were then transferred to a ceramic pressure plate for drainage to 100 kPa suction for one week. Samples were then placed in a growth-cabinet held at 20C with controlled exposure to 14 h light/day. Germination of the seeds, plant height, and number and length of roots were observed. Germination of the seeds held at near-saturation in both coarse- and fine-textured soils was delayed by 24 h compared with seeds held at 10 kPa suction. Neither the number nor the length of tomato roots differed significantly between the different treatments and soils. In the coarse-textured soil, however, the total root length over a period of 14 days was somewhat greater in the uncoalesced samples than in the coalesced samples, but this difference was not statistically significant. These results suggest that aside from delaying germination, aggregate coalescence may not have a large effect on early growth of tomato plants. However, this is not to say that detrimental effects may not be manifest at later stages of plant growth, and this certainly needs to be evaluated, particularly because aggregate coalescence increase with repeated cycles of wetting and draining. In conclusion, the primary findings of the work undertaken in this thesis were: • Rapid wetting of soil aggregates to near-saturation enhanced the onset of soil aggregate coalescence as measured by (in some cases) penetrometer resistance at a soil water suction of 100 kPa, and (in most cases) tensile strength of soil cores in the air-dry state. The rate of wetting appeared to be more important in bringing on aggregate coalescence than how wet the soil eventually became during wetting. This means reducing the rate at which irrigation water is applied to soils may reduce the onset of aggregate coalescence more effectively than controlling the total amount of water applied – though both are important. The literature reports that aggregate coalescence occurs in the field over periods of up to several months, involving multiple wetting and draining cycles, but the work here demonstrated that this can occur over much shorter time periods depending on conditions imposed. • Aggregate coalescence occurred in coarse-textured soils regardless of whether the bulk density increased during wetting and draining. In finer-textured soils, the response to wetting conditions varied and was complicated by changes in bulk density and water content due to swelling. • Small overburden pressures enhanced the onset of aggregate coalescence, but these effects were diminished in the presence of high soil organic matter contents. • Finer aggregate size distributions (which are often produced in the field by excessive tillage during seedbed preparation) invariably led to greater aggregate coalescence than coarser aggregate size distributions. The effects of aggregate size were mitigated to some extent by higher contents of soil organic matter. • Sodicity enhanced aggregate coalescence as measured by tensile strength, but when penetrometer resistance was measured in the moist state, the effects were masked to some extent by higher water contents generated by swelling and dispersion. This work suggests that tensile strength (in the air dry state) may be a more effective measure of aggregate coalescence than penetrometer resistance. • Early plant response to aggregate coalescence was not large, but the response may become magnified during later stages of growth. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1297583 / Thesis (Ph.D.) -- School of Earth and Environmental Sciences, 2007

Aluminum alloys are having more attention due to their high specific stiffness and processing advantages. 7075 aluminum alloy is a wrought composition aluminum alloy in the Al-Zn-Mg-Cu series. Due to the significant addition of these alloying elements, 7075 has higher strength compared to all other aluminum alloys and effective precipitation hardenability characteristic. On the other hand, aluminum alloys have some drawbacks, which hinder the widespread application of them. One of the most commonly encountered defects in aluminum alloys is the hydrogen porosity. Additionally, in case of 7075, another problem is the lack of fluidity. Magnesium addition is thought to be effective in compensating this deficiency. Accordingly, in this study, die cast 7075 aluminum alloy samples with hydrogen porosity and additional magnesium content were investigated. The aim was to determine the relationship between hydrogen content and hydrogen porosity, and the effects of hydrogen porosity, additional magnesium and T6 heat treatment on ultimate tensile and flexural strength properties of pressure die cast 7075 aluminum alloy. 7075 aluminum alloy returns were supplied from a local pressure die casting company. After spectral analysis, pressure die casting was conducted at two stages. In the first stage, 7075 aluminum alloy with an increase in magnesium concentration was melted and secondly 7075 aluminum alloy was cast directly without any alloying addition. While making those castings, hydrogen content was measured continuously before each casting operation. As a final operation T6 heat treatment is carried out for certain samples. Finally, in order to accomplish our aim, mechanical and microstructural examination tests were conducted.

The role of surface chemical effects in hydraulic fracturing of shale is studied using the results of unconfined compression tests and Brazilian tests on Mancos shale- cored at depths of 20-60 ft. The rock mineralogy, total organic carbon and cation exchange capacity were determined in order to characterize the shale. Adsorption tests to study the interaction of the shale and aqueous fluid mixture were also carried out using surface tension measurements. The uniaxial compressive strengths and tensile strengths of individual shale samples after four hours exposure to water, 2.85 x 10^-3 M cationic surfactant (dodecyltrimethylammonium bromide-DTAB) and 2.81 x 10^-3 M anionic surfactant (sodium dodecylbenzenesulfonate-SDBS) were analyzed using ANOVA and Bonferroni tests. These mechanical strengths were largely reduced on exposure to the aqueous environments studied, despite the relatively low clay and low swelling clay content of the Mancos shale. Further comparison of the uniaxial compressive strengths and tensile strengths of the shale on exposure to water, to the strengths when exposed to the surfactant solutions showed that their difference was not statistically significant indicating that exposure to water had the greatest effect on strength loss. The surface tension measurement of 2.85 x 10^-4 M DTAB and 2.81 x 10^-4 M SDBS solutions before and after equilibration with shale showed about 80% increase in surface tension in the DTAB solution and 10% increase in surface tension in the SDBS solution. The probable sorption mechanism is electrostatic attraction with negatively charged sites of the shale as shown by significant loss of the cationic surfactant (DTAB) to the shale surface, and the relatively minor adsorption capacity of the anionic surfactant (SDBS). Although these adsorption tests indicate interaction between the shale and surfactant solutions, within the number of tests carried out and the surfactant concentration used, the interaction does not translate into a significant statistical difference for impacts of surfactants on mechanical strength of this shale compared to the impact of water alone. The relevance of this work is to facilitate the understanding of how the strength of rock can be reduced by the composition of hydraulic fracturing fluids, to achieve improved fracture performance and higher recovery of natural gas from shale reservoirs.

Wood Plastic Composites (WPC) have advantages over natural wood such as improved stiffness, recyclability, and waste minimization. However, issues such as the difficulty of processing WPC with conventional methods, volatile emission from the wood and the composites’ lack of strength must be addressed. A system for continuous extrusion of rectangular profiles of WPC was developed and some critical processing strategies were identified. The use of a lubricant and a calibrator also improved the profile extrusion of WPC. In this work, glass was also added to improve WPC’s mechanical strength. Generally, a glass content of 2.5% appears to improve the properties but further addition does not have a significant effect. Foaming of WPC, which can enhance their properties, was investigated through studying the effect of heating time and temperature on void fraction and cell density. / UOIT

The main purpose of the thesis work is based on achieving same mechanical properties on the three different sized bearing housings. The key mechanical property that had to be focused on was the hardness of the parts. In order to achieve this goal, chemical compositions of the parts have studied. However there were some limitations on the composition variants. Allowed variables of the compositions are silicon, nickel and copper. Due to necessity another element, Molybdenum (Mo), was also introduced. After many simulations three different compositions are proposed. Then the feasibility of results of casting simulation software investigated. And finally an optimization guideline has proposed. Chemical composition researches have carried on casting simulation software, which is called Magma5. Following the completion of the simulations phase, proposed compositions trial casted at the company. Subsequent to trial castings cast parts had tested for their hardness values. In order to bring the thesis to completion simulation outputs and trial test results had compared. With the help of a casting simulation software composition optimisation of different sized parts could be easily optimised in order to achieve same results. Many simulations are executed with different composition for the silicon, nickel, copper and molybdenum variants. It was seen that Mo additions significantly increase the mechanical properties of the parts. Nickel and copperacts similarly on the hardness values, however nickel addition reduce undercooling tendency at a greater rate. Good inoculation is vital for the parts with thin sections. Decent inoculation helps to improve the microstructure and helps to get closer results tothe simulated values. However software represents key information aboutundercooled zones on the part. Software ensures 95% to 97% correct values on hardness results.

Materials derived from chicken feathers could be used advantageously in composite building material applications. Such applications could potentially consume the five billion pounds of feathers produced annually as a by-product of the U.S. poultry industry. To aid the development of successful applications for chicken feather materials (CFM), the physical and mechanical properties of processed CFM have been characterized in this research. Results describing the moisture content, aspect ratio, apparent specific gravity, chemical durability, Youngs modulus, and tensile strength for processed CFM and specifically their fiber and quill components are presented herein. Processed chicken feather fiber and quill samples were found to have similar moisture contents in the range of 16 - 20%. The aspect ratio (i.e., length/diameter) of samples were found to be in the range of 30 - 50, and the fiber material was found to have a larger aspect ratio than the quill material. A comparison with values in the literature suggests that different processing regimes produce CFM with higher aspect ratios. Samples were found to have apparent specific gravities in the range of 0.7 - 1.2, with the fiber material having a higher apparent specific gravity than the quill material. A comparison with values in the literature suggests that apparent specific gravity results vary with fiber length and approach the value for keratin as fiber length decreases and internal voids become increasingly accessible. Chemical durability results showed that CFM rapidly degrade in highly alkaline (pH=12.4) environments and are, thus, likely incompatible with cement-based materials without special treatment. The Youngs modulus of processed chicken feather materials was found to be in the range of 3 - greater than 50 GPa and, thus, comparable to the Youngs moduli of other natural fibers. The tensile strength of oven-dried samples was found to be in the range of 10 - greater than 70 MPa. In agreement with results in the literature, the fiber material was found to have a greater tensile strength than the quill material. Finally, a simplified approach for comparing the effective Youngs moduli and effective tensile strengths of various processed CFM samples was introduced.

This study presents near-field electrospinning (NFES) on flat and hollow cylindrical process to fabricate permanent piezoelectricity of polyvinylidene fluoride (PVDF)/ multi-walled carbon nanotube (MWCNT) piezoelectric nanofibers. Then the mechanical properties of fibers were measured. PVDF is a potential piezoelectric polymer material combining desirable mechanical, thermal, electrical properties with excellent chemical resistance. The existing researches mostly focused on piezoelectric thin film process. However, the research of characteristic about piezoelectric fiber is little. The methods of measurement of the mechanical properties (Young¡¦s modulus, hardness, and tensile strength¡Belongation) of the electrospun PVDF/MWCN composite nanofiber were carried out by using nano-indention test (MTS Nanoindenter Windows XP System) and tensile test (Microforce Testing System). By setting electric field (1¡Ñ107 V/m), rotating velocity (900 rpm) of the hollow cylindrical glass tube on a motion X-Y stage (2 mm/sec) and PVDF solution concentration (16 wt%), and MWCNT (0.03 wt%), in-situ electric poling, mechanical stretching and morphology of PVDF nanofiber were demonstrated. After the experiments of nano-indention test and tensile strength test, it is suggested that the good mechanical properties in NFES on cylindrical process. The results show that the mechanical properties of composite nanofiber are better than the conventional NFES process. The Young¡¦s modulus of 16% PVDF fiber prepared by cylindrical process is 0.89 GPa and hardness is 26.5 MPa. The mechanical properties were increased 56.2% and 49.4% after adding 0.03% of MWCNT, corresponding to 1.39 GPa and 39.6 MPa. The tensile strength was increased 32.7% and elongation at breaking point was increased 35% after adding 0.03% MWCNT.

Faserverbundwerkstoffe werden häufiger für Leichbauanwendungen eingesetzt. Thermoplastische Matrixmaterialien gewinnen in der letzten Zeit immer mehr an Bedeutung wegen höherer Produktivität, niedriger Kosten und besserer Umweltfreundlichkeit sowie Recyclingsfähigkeit. Im Rahmen des Projektes SFB 639 werden Spacer-Strukturen aus GF (Glas)- und PP (Polypropylen)-Filamenten verstärkten Textilien hergestellt. Die vorliegende Arbeit beschäftigt sich mit der Montage von textilen Preformen mittels Nähtechnik und den mechanischen Eigenschaften genähter thermoplastischer Faserverbundwerkstoffe. Das Ziel ist, durch Untersuchungen der Festigkeitseigenschaften von genähten thermoplastischen Faserverbundwerkstoffen die Möglichkeiten gezielter Verbesserung der mechanischen Eigenschaften herauszufinden. Als Versuchsmaterial werden Twintex®-Gewebe und Mehrlagengestrick (hergestellt im ITB) aus GF- und PP-Filamenten verwendet. Durch Zug-, Schub-, Biege- und interlaminare Scherfestigkeitsuntersuchungen ist festzustellen, dass das Nähen an mehrschichtigen thermoplastischen faserverstärkten Verbundwerkstoffe positiv wirken kann. Durch Verwenden thermoplastischer Nähfäden wie beispielsweise Polyester-Nähfäden kann die Zugfestigkeit des Verbundes sogar erhöht werden. Ohne Verminderung der Zugfestigkeit kann das Nähen die Schlagzähigkeit thermoplastischer Faserverbundwerkstoffe wesentlich erhöhen. Bei der Schlagbelastung erzeugen die Nähte neue Arten des Bruchs, so dass mehr Energie aufgenommen wird. Durch das Nähen lässt sich die Schlagzähigkeit besonders bei Faserverbundwerkstoffen mit thermoplastischer Matrix bei niedrigen Temperaturen erhöhen. Die Zugfestigkeitsuntersuchungen von genähten überlappenden Faserverbunden zeigen, dass das Nähen die Zugfestigkeit überlappender Bauteile leicht erhöhen kann. Die Erfahrungen mit der Wirkung von Überlappungen der Verstärkungstextilien in Faserverbundbauteilen mit duromerer Matrix sind nicht auf thermoplastische Matrices zu übertragen. Der Konsolidierungsprozess mit thermoplastischer Matrix mittels Presstechnologie erzwingt eine konstante Wandstärke, so dass lokal im Überlappungsbereich ein erhöhter Faservolumenanteil theoretisch zu erwarten und praktisch nachgewiesen ist. Zur Vorbereitung der Montage von Faserverbundbauteilen kann das Einbringen von Löchern zur Aufnahme von Bolzen oder Schrauben erforderlich sein. Ein Konzept für ein maschinelles Verfahren zur Lochverstärkung wird in dieser Arbeit vorgeschlagen. Der Konstrukteur von Faserverbundbauteilen muss außerdem berücksichtigen, dass ein Gewinn an Schlagzähigkeit mit Verlusten bei den In-Plane-Eigenschaften verbunden ist. Durch eine optimale Wahl der Nahtparameter lassen sich gewünschte Eigenschaften des Faserverbundwerkstoffes einstellen. Trotz vielfältiger, auch berechtigter Kritik besitzt das Nähen als Montageverfahren für Preformen eine Perspektive, wenn die Nähte zielführend positioniert und schonende Nähprozessbedingungen gewährleistet werden.