This thesis describes optimization and modification of standard thick-film electrochemical sensor to be able to be used for detection in microvolumes. In the theoretical part, the thick film technology is described. The work is then focused on the wettability of surfaces followed by introduction to electrochemistry and electro-analytical methods. In the experimental part, screen-printing of various types of thick film pastes on ceramic substrates for determination of their wettability and the following modification of the sensors with thick-film paste and with Parylene vaporization can be found, as well as the basic electrochemical measurements in microvolume using the modified sensor. Finally the results are summarized in conclusion.

The present work related to apply hot-melt ink-jet process for imaging at offset lithographic printing form, to utilise a reusable surface for many times and particularly related to validating thermal and ultrasonic erasing processes. This dissertation investigated systematically the role of certain factors towards affecting erasing image area process on print surfaces. Thermal erasing process approved to melt and suck the image area from the surface, the results were adopted by using contact angle measurements and scanning electron microscope. Ultrasonic erasing process permitted to solve the image area by choosing erasing chemistries, influence of selected erasing chemistries on printing surface, and evaluation the process, the results were tested by UV/Vis spectrometer, contact angle, profileometery and visual microscope. / Der Fortschritt im Bereich von Charakterisierung und Verständnis für Hot-melt Ink Jet Prozesse zur Bebilderung von Offsetdruckform-Zylindern ist ein Ergebnis dieser Forschung. Die Systematik dieser Arbeit basiert auf einem theoretischen Teil, um einen geeigneten Löschprozess auszuwählen. Der Löschprozess hängt von den Eigenschaften des Hot-melt Ink Jet Materials und der genutzten Aluminiumdruckoberfläche ab. Diese werden systematisch im Labormaßstab experimentell untersucht. Der thermische Prozess wurde einerseits durch Benetzbarkeitsprüfungen und anderseites durch Rasterelektronmikroskopaufnahmen bewertet.Der Ultraschallprozess ist ein nasser Löschprozess. Die Untersuchungen wurden in vier Stufen systematisch durchgeführt - Auswahl vom geeigneten Lösungsmitteln - Einflüsse von ausgewählten Lösungsmitteln auf nicht beschichtete und beschichtete Aluminium platten - Evaluation eines Ultraschalllöschprozesses - Validation eines Löschprozesses; zur Bewertung des Löschprozesses wurden mehrere Druckplattenproben bebildert und gelöscht Die Ergebnisse wurden durch UV/Vis Spektrometer, Kontaktwinkel, Profiliometrie und Visuelle Mikroskopie getestet.

Boiling is used in a wide variety of industries, including electronics cooling, distillation, and power generation. Fundamental studies on the boiling process are needed for effective implementation. Key performance characteristics of boiling are the heat transfer coefficient, which determines the amount of heat flux that can be dissipated for a given superheat, and critical heat flux(CHF), the failure point that occurs when vapor blankets the surface. The wettability of a surface is one of the key parameters that affects boiling behavior. Wetting surfaces(e.g., hydrophilic surfaces), typically characterized by a static contact angle below 90°,have better critical heat flux due to effective rewetting, but compromised heat transfer coefficients due to increased waiting times between nucleation of each bubble. Meanwhile, nonwetting surfaces (e.g., hydrophobic surfaces), characterized by static contact angles greater than 90°, have better heat transfer coefficients due to improved nucleation characteristic, but reach critical heat flux early due to surface dry out. However, recent studies have shown that the static contact angle alone offers and incomplete, and sometimes inaccurate, description of this behavior, which is instead governed entirely by the dynamic wettability. Specifically, the receding contact angle impacts the size and contact area of bubbles forming on a surface during boiling, while the advancing contact angle determines how the bubble departs. With this more complete set of wettability descriptors, three characteristic wetting regimes define the boiling behavior: hygrophilic surfaces having advancing and receding contact angles both under 90°; hygrophobic surfaces having both these dynamic contact angles over 90°;and ambiphilic surfaces having a receding contact angle less than 90°, but an advancing contact angle greater than 90°.The goal of this thesis is to experimentally characterize and compare the behavior of boiling surfaces in each of these regimes, observe the contact line behavior, and explain the mechanisms for their differences in performance.

Ce travail de thèse a porté sur le développement de revêtements organiques/inorganiques photopolymérisables superhydrophobes à partir de procédés d’élaboration simples associés à des produits commerciaux largement diffusés. Pour cela, des revêtements à matrice polyuréthane acrylate (PUA), intrinsèquement hydrophiles, incluant différents composés à base de silicium ont été élaborés par enduction ou pulvérisation. L’objectif a été d’apporter en surface des revêtements une structuration multi-échelle et une chimie à caractère hydrophobe nécessaires pour atteindre la superhydrophobie, c’est-à-dire un angle de contact avec l’eau supérieur à 150° et une hystérésis de mouillage inférieure à 10°. L’introduction de molécules de polysilsesquioxane polyédrique (POSS), présentant un ligand acrylate et sept ligands isobutyle, a apporté une nanostructuration et un comportement hydrophobe aux revêtements PUA à des concentrations très faibles (≤ 1% en masse.). Cependant, la rugosité apportée se révèle trop faible et cette stratégie ne peut aboutir à la superhydrophobie des revêtements. L’introduction de particules de silice pyrogénée, modifiées en surface par des chaînes polydiméthylsiloxane, a permis d’établir une structuration multi-échelle et une chimie à caractère hydrophobe à la surface des revêtements PUA, leur conférant ainsi la superhydrophobie. De plus, le procédé d’élaboration a joué un rôle majeur sur les modifications physico-chimiques de surface des revêtements : la superhydrophobie est obtenue à une concentration relativement élevée de 30 et 60% en masse de silice pyrogénée respectivement par pulvérisation et enduction. Afin de diminuer ces concentrations, la combinaison des deux stratégies précédentes, c’est-à-dire l’introduction simultanée de POSS et de silice pyrogénée, a été considérée. Ceci a permis d’exacerber le caractère hydrophobe des revêtements tout en préservant la rugosité établie par la silice pyrogénée. Cette approche a conduit à la diminution de la concentration de silice nécessaire pour obtenir la superhydrophobie dans le cas des revêtements élaborés par pulvérisation. / This work deals with the development of organic/inorganic superhydrophobic UV-curable coatings manufactured through simple processes and from commercially available products. To achieve this goal, a hydrophilic polyurethane acrylate matrix (PUA) was used, in which several silicon-based compounds were introduced. The coatings were deposited using either bar- or spray-coating. The main objective was to structure the surface thanks to a multiscale roughness, while bringing a hydrophobic character, two properties needed to obtain a superhydrophobic coating (defined by a water contact angle superior to 150° and a water contact angle hysteresis inferior to 10°). The introduction of polyhedral oligomeric silsesquioxane molecules (POSS), presenting one acrylate and seven isobutyl ligands, brought a nanostructuration and a hydrophobic behavior to PUA coatings, even at low concentrations (≤ 1%wt.). However, the roughness obtained was not sufficient to bring the superhydrophobicity to the coatings.The introduction of fumed silica particles, functionalized by PDMS chains, established multiscale roughness and hydrophobic behavior at the surface, leading to superhydrophobic coatings. Moreover, the process had a high influence on physico-chemical modifications at the coatings’surface: superhydrophobicity is obtained for a relatively high concentration of fumed silica, 30%wt. and 60%wt. respectively for spray and bar-coating. In order to decrease these concentrations, we tried the combination of the two previous strategies: introduction of POSS molecules and fumed silica particles. This path raised the hydrophobic behavior of the coatings while keeping intact the roughness brought by fumed silica particles. This approach allowed to decrease the silica concentration needed to obtain superhydrophobicity for spray-coated coatings.

No description available.

Рассмотрены существующие методы проведения операции чистки оптических поверхностей с целью удаления с нее всех загрязнений и создание необходимого состояния поверхности. Приведены результаты измерения краевого угла смачивания, который позволяет проанализировать, какие свойства обретает поверхность после чистки. Описан комплекс измерительного оборудования для определения угла смачивания поверхности жидкостью. / The existing methods of carrying out the operation of cleaning optical surfaces in order to remove all contaminants from it and create the required surface condition are considered. The results of measuring the contact angle of wetting are given, which makes it possible to analyze what properties the surface acquires after cleaning. A set of measuring equipment for determining the angle of surface wetting with a liquid is described.

No / OBJECTIVES: To compare the properties of solid dispersions of felodipine for oral bioavailability enhancement using two different polymers, polyvinylpyrrolidone (PVP) and hydroxypropyl methylcellulose acetate succinate (HPMCAS), by hot-melt extrusion (HME) and spray drying. METHODS: Felodipine solid dispersions were prepared by HME and spray drying techniques. PVP and HPMCAS were used as polymer matrices at different drug : polymer ratios (1 : 1, 1 : 2 and 1 : 3). Detailed characterization was performed using differential scanning calorimetry, powder X-ray diffractometry, scanning electron microscopy and in-vitro dissolution testing. Dissolution profiles were evaluated in the presence of sodium dodecyl sulphate. Stability of different solid dispersions was studied under accelerated conditions (40 degrees C/75% RH) over 8 weeks. KEY FINDINGS: Spray-dried formulations were found to release felodipine faster than melt extruded formulations for both polymer matrices. Solid dispersions containing HMPCAS exhibited higher drug release rates and better wettability than those produced with a PVP matrix. No significant differences in stability were observed except with HPMCAS at a 1 : 1 ratio, where crystallization was detected in spray-dried formulations. CONCLUSIONS: Solid dispersions of felodipine produced by spray drying exhibited more rapid drug release than corresponding melt extruded formulations, although in some cases improved stability was observed for melt extruded formulations.

This dissertation includes a theoretical and numerical development to simulate liquid-vapor flows and the applications to microchannels. First, we obtain a consistent non-local pressure equation for simulating liquid-vapor interfacial flows using mean-field free-energy theory. This new pressure equation is shown to be the general form of the classical van der Waals" square-gradient theory. The new equation is implemented in two-dimensional (2D) D2Q7, D2Q9, and three-dimensional (3D) D3Q19 lattice Boltzmann method (LBM). The three LBM models are validated successfully in a number of analytical solutions of liquid-vapor interfacial flows. Second, we have shown that the common bounceback condition in the literature leads to an unphysical velocity at the wall in the presence of surface forces. A few new consistent mass and energy conserving velocity-boundary conditions are developed for D2Q7, D2Q9, and D3Q19 LBM models, respectively. The three LBM models are shown to have the capabilities to successfully simulate different wall wettabilities, the three typical theories or laws for moving contact lines, and liquid-vapor channel flows. Third, proper scaling laws are derived to represent the physical system in the framework of the LBM. For the first time, to the best of the author's knowledge, we obtain a flow regime map for liquid-vapor channel flows with a numerical method. Our flow map is the first flow regime map so far for submicrochannel flows, and also the first iso-thermal flow regime map for CO₂ mini- and micro-channel flows. Our results show that three major flow regimes occur, including dispersed, bubble/plug, and liquid strip flow. The vapor and liquid dispersed flows happen at the two extremities of vapor quality. When vapor quality increases beyond a threshold, bubble/plug patterns appear. The bubble/plug regimes include symmetric and distorted, submerged and non-wetting, single and train bubbles/plugs, and some combination of them. When the Weber number<10, the bubble/plug flow regime turns to a liquid strip pattern at the increased vapor quality of 0.5~0.6. When the Weber number>10, the regime transition occurs around a vapor quality of 0.10~0.20. In fact, when an inertia is large enough to destroy the initial flow pattern, the transition boundary between the bubble and strip regimes depends only on vapor quality and exists between x=0.10 and 0.20. The liquid strip flow regimes include stratified strip, wavy-stratified strip, intermittent strip, liquid lump, and wispy-strip flow. We also find that the liquid-vapor interfaces become distorted at the Weber number of 500~1000, independent of vapor quality. The comparisons of our flow maps with two typical experiments show that the simulations capture the basic and important flow mechanisms for the flow regime transition from the bubble/plug regimes to the strip regimes and from the non-distorted interfaces to the distorted interfaces. Last, our available results show that the flow regimes of both 2D and 3D fall in the same three broad categories with similar subdivisions of the flow regimes, even though the 3D duct produces some specific 3D corner flow patterns. The comparison between 2D and 3D flows shows that the flow map obtained from 2D flows can be generally applied to a 3D situation, with caution, when 3D information is not available. In addition, our 3D study shows that different wettabilities generate different flow regimes. With the complete wetting wall, the flow pattern is the most stable. / Ph. D.

Capillary trapping plays a central role in the geological storage of CO2, oil recovery, and water soil infiltration. The key aim of this study is to investigate the impact of surface properties (wettability, roughness, heterogeneous mineral composition) on the dynamics of quasi-static fluid displacement process and capillary trapping efficiency in porous medium. We concluded that for homogeneous wet smooth glass beads surfaces, a transition in fluid displacement pattern occurs from a compact (for θ < 90°; imbibition process) to a fractal front-pattern (for θ > 90°; drainage process) leading to a crossover in capillary trapping efficiency from zero to maximum. The impact of surface roughness on capillary trapping efficiency was also studied, and an opposite trends in terms of wettability dependency was observed. Rough natural sands surfaces depicts a non-monotonous wettability dependency, i.e. a transition from maximal trapping (for θ < 90°) to no-trapping occurs (at θ = 90°), followed by an increase to medium trapping (for θ > 90°). For a fractional-wet media, the percolating cluster of hydrophobic sediments (connected hydrophobic pathways) characterize the fluid displacement pattern and trapping efficiency.

L’assemblage des matériaux composites thermoplastiques tel que le PEEK est l’une des problématiques majeure de l’industrie aéronautique. Actuellement, différentes techniques sont développées pour assurer l’assemblage structural de ces matériaux, tels que : le soudage, le rivetage, le boulonnage et le collage. Les enjeux industriels majeurs sont principalement, à l’heure actuelle, la conception des structures simplifiées au maximum afin de réduire les coûts de production et la réduction des consommations énergétiques. A cet effet, l’industrie aéronautique fait fréquemment appel à l’assemblage par collage en raison de nombreux avantages qu’il offre (gain de poids, distribution régulière des contraintes, absence de trous) par rapport aux autres techniques existantes. Le PEEK (PolyEtherEtherKetone), est un matériau polymère semi-cristallin thermoplastique, à hautes performances. Ce matériau est souvent utilise dans l’industrie aéronautique principalement renforce par des fibres de carbone ou de verre. Cependant, du fait du niveau élevé de sa résistance chimique l’assemblage par collage du PEEK et de ses composites nécessitent des traitements de surfaces appropries et optimises. Or, afin d’obtenir un system collé à haute performance, la problématique scientifique et technique doit être concentrée sur la jonction entre les éléments à assembler. En effet, la qualité de cette jonction est de la plus haute importance car elle doit permettre un transfert optimal des contraintes thermomécaniques lorsque l’assemblage est soumis a ses conditions d'usage. Cette étude concerne donc, l’amélioration des propriétés mécaniques (monotones et cycliques) de l’assemblage par collage PEEK/PEEK. Dans cette optique, un traitement de surface simple de mise en œuvre est proposé. Ce traitement est le sablage, qui permet la modification topographique (morphologique) de surface. La compréhension des différents phénomènes d’interaction aux interfaces intervenant dans l’amélioration du comportement mécanique du joint de colle et qui s’inscrit dans la triptyque : « Rhéologie, Physico-chimie et topographie », est l’enjeu scientifique majeur dans cette thèse. Dans un premier temps, l’influence des paramètres du traitement tels que le temps de projection, la taille des particules, sur la morphologie de surface de différents matériaux à base de PEEK a été analysée, permettant ainsi d’établir la corrélation entre les paramètres morphologiques et les mécanismes de modification topographique de surface intervenant pendant le traitement de surface. L’un des facteurs clefs pour la compréhension des mécanismes d’interaction entre l’adhésif liquide et le substrat solide est la mouillabilité. L’analyse du comportement au mouillage en fonction des différents paramètres du traitement a été réalisée. La mouillabilité des surfaces traitées est fortement affectée par la rugosité de surface créée après ce traitement. La relation entre les paramètres morphologiques et la mouillabilité a été discutée. Enfin, l’influence des paramètres du traitement par sablage sur le comportement mécanique monotone et à long terme (essais de fatigue) sur la résistance du joint colle a été étudié à l’aide d’essais de cisaillement sur éprouvettes à simple recouvrement. Ceci a conduit, à la proposition de paramètres morphologiques surfaciques spécifiques pour l’optimisation du comportement mécanique du joint de colle des matériaux composites à matrice PEEK. / One of most problematic in the aeronautical industries is the structural joining of the high performance thermoplastic composites like PEEK composites. Actually, a lot of technologies are used for joining thermoplastic composites like welding, bolting, riveting, fastening and adhesive bonding. Due to the various advantages that characterize the adhesive bonding method, such an uniform stress distribution along the joint, weight‐light and cost reduction, makes this technique more desirable to join thermoplastic composites materials compared to the other joining techniques. PEEK (PolyEtherEtherKetone) is a semi‐crystalline thermoplastic material with high performance. This material is wildly used in aeronautical industries, principally, reinforced with carbon of glass fibres. However, its high chemical resistance makes the adhesive bonding of PEEK and its composites difficult and therefore an appropriate and optimised surface treatment is necessary. In the aim to obtain a bonded system with high performance, scientific and technical problematic should be focussed on the junction between adherents. Indeed, the quality of this junction is of utmost importance because it must allow optimum transfer of thermomechanical stresses when the assembly is subject to its terms of use. Though, at this time it is well known that thermoplastic composite materials are difficult to bond with‐out surface treatment. This study, therefore, relates to the improvement of mechanical properties (monotonic and cyclic) of the adhesive bonding system PEEK / PEEK. In this context, a surface treatment, easy to implement, is proposed. This surface treatment is sandblasting, which enables surface topographic (morphological) modifications. Understanding of various phenomena of interfaces interaction involved in the improvement of the mechanical behavior of the adhesive joint and is part of the triptych "Rheology, Physico‐chemistry and topography" is the major scientific challenge in this thesis. Initially, the influence of processing parameters such as the projection time, the particle size on surface morphology of various materials based on PEEK was analysed, thus allowing establishing the correlation between morphological parameters and modification mechanisms involved during surface treatment surface. One of the key factors for understanding the mechanisms of interaction between the liquid adhesive and the solid substrate is wettability. The analysis of the wetting behavior as a function of various parameters of the treatment was performed. The wettability of treated surfaces is strongly affected by surface roughness created after this treatment. The relationship between morphological parameters and wettability was discussed. Finally, the influence of sandblasting processing parameters on the mechanical behavior in monotoning and long‐term (fatigue tests) of the adhesive joint strength was studied, using single lap shear tests specimens. This has led to the proposal of specific surface morphological parameters for the optimization of the mechanical behavior of the adhesive joint of PEEK and its composites.