In the present work, novel dewatering aids and a novel centrifuge configuration were developed and applied for the purpose of dewatering fine particles. Three different types dewatering reagents were tested in different filtration and centrifugation units. These chemicals included low-HLB surfactants, naturally occurring lipids, and modified lipids. Most of these reagents are insoluble in water; therefore, they were used in solutions of appropriate solvents, such as light hydrocarbon oils and short-chain alcohols. The role of these reagents was to increase the hydrophobicity of the coal and selected mineral particles (chalcopyrite, sphalerite, galena, talc, clay, phosphate, PCC and silica) for the dewatering. In the presence of these reagents, the water contact angles on the coal samples were increased up to 90o. According to the Laplace equation, an increase in contact angle with the surfactant addition should decrease the capillary pressure in a filter cake, which should in turn increase the rate of dewatering and help reduce the cake moisture. The use of the novel dewatering aids causes a decrease in the surface tension of water and an increase in the porosity of the cake, both of which also contribute to improved dewatering. A series of batch-scale dewatering tests were conducted on a variety of the coal and mineral samples using the novel dewatering aids. The results obtained with a Buchner funnel and air pressure filters showed that cake moistures could be reduced substantially, the extent of which depends on the particle size, cake thickness, drying time, reagent dosage, conditioning time, reagent type, sample aging, water chemistry, etc. It was determined that use of the novel dewatering aids could reduce the cake formation time by a significant degree due to the increased kinetics of dewatering. At the same time, the use of the dewatering aids reduced the cake moistures by allowing the water trapped in smaller capillaries of the filter cake. It was found that final cake moistures could be reduced by 50% of what can be normally achieved without using the reagents. However, the moisture reduction becomes difficult with increasing cake thickness. This problem can be minimized by applying a mechanical vibration to the cake, spraying a short-chain alcohol on the cake and by adding a small amount of an appropriate coagulant, such as alum and CaCl2 to the coal and mineral slurries. The novel dewatering aids were also tested using several different continuous filters, including a drum filter, disc filter and horizontal belt filter (HBF). The results obtained with these continuous filtration devices were consistent with those obtained from the batch filters. Depending on the coal and mineral samples and the type of the reagent, 40 to 60% reductions in moisture were readily achieved. When using vacuum disc filters, the cake thickness increased substantially in the presence of the novel dewatering aids, which could be attributed to the increased kinetics of dewatering. A dual vacuum system was developed in the present work in order to be able to control the cake thickness, which was necessary to achieve lower cake moistures. It was based on using a lower vacuum pressure during the cake formation time, while a full vacuum pressure was used during the drying cycle time. Thus, use of the dual vacuum system allowed the disc filter to be used in conjunction with the novel dewatering aids. Its performance was similar to that of HBF, which is designed to control cake thickness and cake formation time independently. The effectiveness of using the novel dewatering aids were also tested in a full-continuous pilot plant, in which coal samples were cleaned by a flotation column before the flotation product was subjected to the disc filter. The tests were conducted with and without using novel dewatering aids. These results were consistent with those obtained from the laboratory and batch-scale tests. The novel centrifuge developed in the present work was a unit, which combined a gravity force and air pressure. The new centrifuge was based on increasing the pressure drop across the filter cake formed on the surface of the medium (centrifuge wall). This provision made it possible to take advantage of Darcy s law and improve the removal of capillary water, which should help lower the cake moisture. A series of tests were conducted on several fine coal and mineral particles and obtained more than 50% moisture reduction even at very fine particle size (2 mm x 0). Based on the test results obtained in the present work, two proof-of-concept (POC) plants have been designed. The first was for the recovery of cyclone overflows that are currently being discarded in Virginia, and the other was for the recovery of fines from a pond in southern West Virginia. The former was designed based on the results of the plant tests conducted in the present work. Cost vs. benefit analyses were conducted on the two POC plants. The results showed very favorable internal rates of return when using the novel dewatering aids. Surface chemistry studies were conducted on the coal samples based on the results obtained in the present investigation. These consisted mainly of the surface characterization of the coal samples (surface mineral composition, surface area, zeta potential, x-ray photoelectron microscopy (XPS)), acid-base interactions of the solids and liquids, dewatering kinetic tests, contact angle measurements of the coal samples and surface force measurements using AFM. In addition, carbon coating on a silica plate using palsed laser deposition (PLD) and Langmuir-Blodgett (LB) film deposition tests were conducted on the sample to better understand the surfactant adsorption and dewatering processes. The test results showed that the moisture reductions on the fine particles agree well with the surface chemistry results. / Ph. D.

Syfte: Syftet med studien var att jämföra två metoder vid undersökning av tårfilmsanalys; tårflödesbeteende-metoden och fluorescein break-up mönster och om deras mätresultat överensstämmer med varandra. Detta för att diskutera om någon av metoderna kunde vara ett bättre alternativ att adaptera ute i praktiken för vårdgivare inom ögonvården. Metod: Initialt fick deltagarna besvara en OSDI-enkät (ocular surface disease index), därefter gjordes resterande mätningar i biomikroskopet. I biomikroskopet utfördes initialt dem icke-invasiva mätningarna som tillhörde tårflödesbeteende-metoden (mätning av TMH (tårmeniskhöjd), debrishastighet efter blinkning och mätning av lipidlagrets interferensmönster) även NiBUT (non-invasive tear break-up time) utfördes. Efter dem icke-invasiva mätningarna tillsattes fluorescein i inferiora temporala fornix och dem invasiva testerna; TBUT (tear break-up time) och FBUP (fluorescein break-up mönster) utfördes tre gånger. Alla mätningar dokumenterades med video. Tre oberoende bedömningar utfördes. Studien undersökte om resultatet av tårflödesbeteendet och FBUP hade ett samband och vilken utav metoderna som fick en högre intravaliditet utefter dem bedömningar som utfördes. Resultat: Totalt deltog 26 deltagare varav 4 exkluderades. Deltagarna var mellan 19–57 år gamla med en genomsnittsålder på 35 år och en standardavvikelse på ±12,3 år. Samtliga presenterade med en OSDI ≥13, alternativt hade en visuellt frekvent blinkfrekvens. Det återfanns ett samband mellan tårflödesbeteende-metoden och FBUP i studien, dock ingen av klinisk signifikans ((bedömare 1, Cramer’s V= 0,46 p=0,06) (bedömare 2, Cramer’s V=0,33 p=0,32) (bedömare 3, Cramer’s V=0,33 p=0,34)). Tårflödesbeteende-metoden (Fleiss kappa =0,29, p=0,40) och FBUP (Fleiss kappa =0,25, p=0,40) uppvisade båda på en mindre god intra-validitet Slutsats: Det finns ett samband mellan tårflödesbeteende-metoden och FBUP men ingen statistisk signifikans. Intravaliditeten är marginellt högre vid tårflödesbeteende-metoden än vid FBUP i studien. / Aim: The aim of this study was to compare two methods used during tear-film analysis; tear-flow behaviour, and fluorescein break-up pattern and if their measured results are in an agreement. This in order to discuss which one of the methods would be more suitable to apply in clinical practice for healthcare workers in the field of optometry.  Method: Initially the participants filled out an OSDI questionnaire (ocular surface disease index), thereafter measurements were done in the biomicroscope. Initially the non-invasive measurements such as the tear-flow behaviour method (measurements of TMH (tear meniscus height), speed of debris movement across the tear film after blinking and measurements of the lipid layer interference) and NiBUT (non-invasive break-up time) were measured. Afterwards fluorescein was applied in the inferior temporal fornix and the invasive measurements; TBUT (tear break-up time) and FBUP (fluorescein break-up pattern) were measured three times. All measurements done in the biomicroscope were documented with video and three independent assessments were done. This study looked at the results from the tear-flow behaviour and FBUP and if they agreed with one another. It also looked into which one of the methods presented a higher intra-validity in regard to the assessments made. Results: The study had a total of 26 participants, of which 4 were excluded. The participants were between the ages of 19-57 years old with an average age of 35 years with a standard deviation of ±12,3 years. The participants presented with an OSDI of ≥13, with exceptions made if a participant visually had a high blink frequency. A correspondence between the tear-flow behaviour method and  FBUP could be observed, however none of statistical significance ((assessor 1, Cramer’s V= 0,46 p=0,06) (assessor 2, Cramer’s V=0,33 p=0,32) (assessor 3, Cramer’s V=0,33 p=0,34)). The intra-validity of the tear-flow behaviour method (Fleiss kappa =0,29, p=0,40) and FBUP (Fleiss kappa =0,25, p=0,40) were both categorized as weak intra-validity.  Conclusion: There is a correspondence between the tear-flow method and FBUP, without statistical significance. The intra-validity was marginally higher within the tear-flow method compared to FBUP in the study.

The application of surfactants and polymers in carbonate reservoirs has a high potential with emerging technology of the manufacture of these chemicals. Tertiary or enhanced oil recovery with chemicals (CEOR) will become more relevant with decreasing new exploration of oil deposits and high remaining oil saturations in huge carbonate oil reservoirs. However, in several oil deposits, high reservoir brine salinity and moderate to high reservoir temperature are encountered. Under such conditions, many chemicals will be insoluble or degrade fast. A selection of commercial and research surfactants and polymers has been investigated for their application under brine salinity of up to 18 percent by weight with significant hardness and a moderate reservoir temperature of 70 °C. Chemical systems were tested towards outcrop limestone rock samples and calcite platelets in combination with a crude oil, which was modified by different organic acids regarding its wetting potential. Wettability alteration from preferentially oil-wet core plugs was pursued with ethoxylated tertiary amines and quaternary ammonium compounds. The main mechanism of wettability alteration towards more water-wet was proposed as extraction of carboxylate anions from the oil phase and the solid samples into aqueous micelles. Thus, high surfactant concentrations would result in improved recovery. From screening of different surfactant combinations in tertiary core flooding, one promising system of an alkyl ether sulfate and hexadecyltrimethylammonium combined with a terpolymer (TP) from acrylic acid, ATBS and NVP is proposed for the examined conditions. Low to moderate adsorption of the single surfactants and their combination as well as a favorable, stabilized phase behavior when combined with the polymer emphasize the applicability of the system. However, long term stability can be an issue with respect to the sulfate surfactant degradation at 70 °C. Analysis of mixed ionic surfactant systems after adsorption testing has been successfully pursued with a combined TC/TNb-determination.

L’objectif de ce travail de thèse était d’étudier l’effet de la stérilisation par électrons accélérés sur les copolymères d’oléfines cycliques (COC), utilisés comme conditionnement de produits pharmaceutiques, ainsi que son impact sur les interactions avec des formulations pharmaceutiques. Grâce à la méthodologie analytique adoptée qui a fait appel à différentes techniques de caractérisation, telles que la chromatographie d’exclusion stérique, la chromatographie liquide haute performance à polarité de phases inversée, la spectroscopie infra rouge à transformée de Fourier, la microscopie à force atomique et les mesures d’angles de contact, nous avons pu mettre en évidence différents types de modifications dans le volume et sur la surface du matériau après stérilisation ainsi qu’après vieillissement. La modification principale du dans la masse du matériau, observée à la dose réglementaire de stérilisation (25 kGy), est la scission des chaînes du polymère, qui s’accompagne de la création de composés de faible masse molaire, donc de migrants potentiels risquant d’influencer la sécurité d’emploi des COC. En effet, certains de ces composés ont été retrouvés avec une concentration relativement importante dans les solutions de mise en contact avec les COC stérilisés, et notamment en solution aqueuse. Toutefois, l’étude préliminaire de toxicité a montré l’absence de cytotoxicité des extractibles obtenus à la dose de la stérilisation.Les modifications relatives à la surface des COC radio-stérilisés sont, quant à elles, de deux natures : physique avec une augmentation de la rugosité de surface et chimique avec la formation de produits d’oxydation polaires ; ces deux types de modifications conduisent à l’augmentation de la mouillabilité de surface. Cependant dans certains cas, notamment après vieillissement, ces modifications sont relativement faibles, même à des doses supérieures à celle préconisée pour la stérilisation, ce qui peut être corrélé à l’absence de l’effet de l’irradiation sur le comportement des COC vis-à-vis des solutions médicamenteuses. En effet, aucune variation de la sorption des principes actifs choisis n’a été montrée entre les COC irradiés et non irradiés vieillis. / The aim of this work was to study the effect of electron beam radio-sterilization on cyclo olefins copolymers (COC) used as pharmaceutical storage materials, as well as to investigate its impact on the interaction with pharmaceuticals formulations. Due to the analytical methodology used which dealt with different techniques of characterization such as size exclusion chromatography, reversed phase high performance liquid chromatography, Fourier transformed infrared spectroscopy, atomic force microscopy and contact angle measurements, we have been able to put into evidence different kinds of modifications both in the bulk and on the surface of the sterilized material and also after ageing.The principal modification of material’s bulk, observed at the recommended dose for sterilization (25 kGy), was polymer chains scissions, accompanied with creation of low molecular weight compounds, that are potentials migrants that risk to affect the safe use of COC. Indeed, some of these compounds have been found with a relatively important concentration in the solutions where sterilized COC was stored, especially in aqueous solutions. However, the preliminary study of toxicity has shown the absence of cytotoxicity of the extractables obtained at the sterilization dose.Surface modifications of radio-sterilized COC are of two types: a physical one, with an increase of the surface’s roughness and a chemical one with the formation of polar oxidation products; these two modifications result in an increase of surface’s wettability that may be important. However, in some cases such as for aged samples, these modifications are relatively weak even at doses higher than the one recommended for sterilization, which can explain the absence of the effect of radiation on the behavior of COC towards drug solutions. Indeed, no variation of drug sorption has been observed between aged COC irradiated and none irradiated.

Gegenstand der Arbeit sind Zusammenhänge zwischen physikochemischen Eigenschaften und Funktionen der Exine bei Ausbreitung, Bestäubung und Befruchtung. Dabei bewährte sich der Einsatz der 3-kammrigen Sporopolleninkapseln (Zentralkapsel und Sacci) in der Permeationschromatographie. Sowohl kinetisch bedingte chromatographische Dispersion kleiner Moleküle als auch Konzentrationsänderungen von Zuckern und Dextranmolekülen im Medium wurden zur Bestimmung von Permeabilitätskoeffizienten der Nexine genutzt. Die Wasserabsorptionskapazität von Exinefragmenten und die hydraulische Leitfähigkeit der Nexine wurden anhand von Konzentrationsänderungen ausgeschlossener Dextranmoleküle ermittelt. Das Tectum der saccalen Sexine ist eine Mikrofiltermembran mit scharfer Trenngrenze im Submikrometerbereich; daher werden an den Sacci nur Hydrokolloide mit Stokes''schen Radius über 100 nm (z.B. aus nativem Dextran) ausgeschlossen. Die Nexine ist eine nicht-ideale Umkehrosmose-Membran, die in Zucker- und Salzlösungen hohe Reflexionskoeffizienten zeigt; zusätzlich besitzt sie wenige große Poren, die den Austausch von Zuckern und selbst kleinen Polymermolekülen ermöglichen. Die hydraulische Leitfähigkeit der Nexine liegt im Größenbereich derjenigen von Plasmamembranen (0,39-0,48 µm s-1 MPa-1); die Ergebnisse zeigen, dass die Exine weder die Nährstoffaufnahme des Sporoplasten aus der lokulären Flüssigkeit noch dessen rasche Rehydratation in der Mikropyle behindert. Die Einfaltungen der distalen Nexine (oberhalb der Sacci) und die Omega-Faltung der Exine zwischen den Sacci (Leptom) bieten beim Quellvorgang Schutz vor zu schneller Flächenausdehnung der Plasmamembran. Der Corpus kann mit konzentrierten Elektrolytlösungen beladen werden. Beim anschließenden osmotischen Schwellen in Wasser reißt die Exine, und der Sporoplast wird mit anhaftender Intine ausgeschleudert. Wasser und andere polare Flüssigkeiten adhärieren stärker als hydrophobe Flüssigkeiten an Sporopollenin. Die Sporopolleninmatrix weist eine hohe Feststoffdichte auf, ist wenig quellfähig (0,18 mL g-1 TM) und deformationsstabil. Dies ermöglicht die Pulverbildung beim Trocknen. / Subject of this thesis are relationships between physicochemical properties and functions of the exine concerning propagation, pollination and fecundation. Here the application of the 3-chambered sporopollenin-microcapsules (central capsule and sacci) in permeation chromatography proved of value. Both the kinetically dependent dispersion of small molecules and changes in concentration of sugars and dextran molecules in the medium were analysed to determine permeability coefficients of the nexine. The water absorption capacity of exine fragments and the hydraulic conductance of the nexine were calculated by means of changes in concentrations of excluded dextran molecules. The tectum of the saccal sexine is a microfiltration membrane with a sharp cut off in the submicrometer range; thus hydrocolloids with Stokes´radii over 100 nm (e.g. from native dextran) are excluded from the sacci. The nexine is a non-ideal reverse osmosis membrane having high reflexion coefficients in sugar and salt solutions; in addition few large pores allow the exchange of sugars and even of small polymers. The hydraulic conductance of the nexine is in the range typically for plasmamembranes (0.39-0.48 µm s-1 MPa-1); the results indicate that the exine does neither obstruct the uptake of nutrients by the sporoplast from the locular fluid nor hinder the rapid rehydration in the micropyle. When rehydrating, the distal foldings of the nexine (above the sacci) and the omega-like folding of the exine between the sacci (leptom), provide protection for the plasmamembrane when its surface area has to increase too rapidly. The corpus can be loaded with a concentrated electrolyte solution. When subsequently transferred into water the exine rupture and the sporoplast along with the intact intine is ejected. Water and other polar liquids adhere stronger to sporopollenin than hydrophobic ones. The matrix of sporopollenin show a high density in its solid content, water absorption capacity is low (0.18 mL g-1 DM) and it is resistant to deformation. This enable the formation of powder while dehydrating.