Alternative energy sources such as solar energy have attracted an extensive interest in the petroleum shortage era. Among solar cells, dye-sensitized solar cell (DSSC) attracts the attention of widespread research teams because of the easy-production process, low cost, and good photon-to-electron conversion efficiency. In this study, both UV and acid solution such as HCl are used to improve the efficiency of DSSC. The UV illumination can eliminate organic contaminates on TiO2 by photocatalysis and enhance the adsorption of dye molecules. Meanwhile, the coordination mode between TiO2 and dye could be changed and lower the electron transportation. If the HCl solution is used after UV illumination, the coordination mode can be preserved. Moreover, H+ from HCl can attract the COO¡Ð anchoring group of dye by electrostatic force. It further increases the adsorption of dye and improves the DSSC efficiency. The coordination mode was measured by Fourier-transform infrared spectrometer (FTIR). The internal resistance was measured by electrical impedance spectroscopy (EIS). The chemical properties were characterized by X-ray photoelectron spectroscopy (XPS). The light absorbance was measured by ultraviolet-visible spectroscopy (UV-Vis). The morphology was observed by field emission scanning electron microscope (FE-SEM). The performance of the cells was measured by a semiconductor device analyzer. In our results, the conversion efficiency was improved from 6.29% of untreated one to 6.71 and 7.39% for UV and UV + HCl treated ones.

TiO2 in anatase form is the most widely studied material for photocatalytic reactions. Utilization of oxide support materials such as silica with suitable transparency within band gap range of TiO2 is promising technique to obtain efficient photocatalysts for many applications. In the present study, simultaneous co-hydrolyzation of tetraethyl orthosilacate (TEOS) and titanium tetrabutaoxide (TBOT) precursors were carried out in the presence of hydrochloric acid. The effects of washing with low vapor pressure solvent(n-octane), drying conditions, hydrothermal ageing and TiO2/SiO2 ratio on the catalyst structure and photocatalytic activity were studied. The samples were characterized by XRD, BET, DRIFTS techniques and the activity was measured for liquid phase room temperature oxy/demineralization of phenol under artificial solar irradiation. The reaction intermediates were followed by UV/vis spectrophotometer and HPLC. It was found that the hydrothermal treatment contributes better degree of crystalinity, higher surface area and thus photocatalytic activity compared to the samples which were synthesized with conventional drying at 100oC overnight. The formation of Ti-O-Si interface indicating the degree of dispersion was evidenced by DRIFTS technique for all hydrothermally tretated samples. The highest surface area and photocatlytic activity was observed with hydrothermally treated catalyst with TiO2/SiO2:0.34 composition.

The aim of this study was to investigate the viability of patterning by immobilization, photocatalytic removal, and re-immobilization steps of the enzyme on photocatalytically active thin films for biosensor fabrication purposes. For this aim, TiO2-SiO2-Au sol-gel colloids were synthesized and deposited on glass substrates as thin films by dip coating. Cysteamine linker was assembled on gold nanoparticles to functionalize thin films with amine groups for immobilization of model enzyme invertase. Effect of immobilization temperature, enzyme concentration of the immobilization solution and immobilization period on invertase immobilization were investigated. The immobilized invertase activity was found independent from the immobilization temperature in the range tested (4oC-room temperature). The optimum enzyme concentration and period for immobilization was determined as 10&micro / g/ml and 12 hours respectively. The resulting invertase immobilized thin films showed high storage stability retaining more that 50% of their initial activity after 9 weeks of storage. Photocatalytic enzyme removal and re-immobilization studies were carried out by irradiating the invertase immobilized thin films with blacklight. Upon 30 minutes of irradiation, immobilized invertase was completely and irreversibly inactivated. Initial immobilized invertase activity (before the irradiation) was attained when invertase was re-immobilized on thin films that were irradiated for 5 hours. Thus it was inferred that with sufficient exposure, enzymes can be completely removed from the surfaces which makes the re-immobilization possible. The possibility of enzyme removal with photocatalytic activity and re-immobilization can pave the way to new patterning techniques to produce multi-enzyme electrode arrays.

Silver (Ag) was loaded to three different kinds (P-25, NT-22, and TiO(OH)2) of titanium dioxide (TiO2) powders through adding three different quantities (4.6, 9.2, and 13.8 ml) of silver nitrate (AgNO3) solution by mechanical ball milling process. X-Ray diffraction analysis suggested that Ag was loaded on the TiO2 powders in the form of silver oxide (AgO). SEM, particle size, and BET surface area analyses revealed that TiO2 particles agglomerated after ball milling, resulting in the decrease of specific surface area of the TiO2 powders. Powders P-25, NT-22, and TiO(OH)2 degraded 94 %, 46 %, and 26 %, respectively of MO solution under 1 h UV irradiation. Increasing amount of Ag loading enhanced photocatalytic activity of TiO2 powders under UV irradiation. The best photocatalytic performance was achieved by 13.8 ml AgNO3 solution added NT-22 powders. Percent methyl orange (MO) degradation of 13.8 ml AgNO3 solution added P-25, NT-22, and TiO(OH)2 powders under 1 h UV irradiation was 85 %, 96 %, and 67 %, respectively. Contact angle measurements revealed that hydrophilic properties of TiO2 powders were also improved by Ag loading. Moreover, TiO2 powders gained antibacterial prospect after Ag addition. Ag loaded TiO2 powders could be used effectively for the applications requiring better photocatalytic activity and antibacterial effect.

The photocatalytic activity of semiconductor metal oxides can be improved by the addition of sensitizer which enhances the band gap by considerable red shift of the absorption edge of semiconductor. In the present study, the effect of ascorbic acid as sensitizer on the photocatalytic activity of titania-silica binary mixtures was studied. The SiO2-TiO2 mixtures having 50wt%Ti:Si composition were prepared with sol-gel method. The surface area and porosity of the samples were modified by using various amounts of polyethylene glycol (PEG) as template. The thin films of the samples were obtained by dip coating of glass plates to colloidal solutions. The samples were characterized by methylene blue adsorption method and UV-Vis spectrophotometry. The photocatalytic activities of the samples were measured with methylene blue degradation, methyl orange degradation and direct water splitting in the presence and absence of ascorbic acid. Increase in the surface area and reaction rate with increasing PEG addition until a threshold value was observed. Highest methylene blue degradation activity was observed for 27g PEG added sol-gel derived film and surface area of this film is measured as 44m2/m2. Ascorbic acid presence shows a significant increase in the photocatalytic degradation activity of methyl orange. The sensitization effect of ascorbic acid was also compared with the effect of EDTA. It was found that the effect of ascorbic acid on the methyl orange degradation rate is significantly higher than the effect of EDTA. However, the effect of EDTA is more pronounced in water splitting reaction.

Zinc oxide (ZnO) has higher exiton binding energy (60 meV) and high band gap (~3.4 eV) that can provide efficient ultraviolet (UV) light at room temperature (RT). The easily etched in acids and alkalis that provides the fabrication of small-size ZnO-based devices. Electrodeposition is the growth method that can deposit high quality film and modify the characterizations of film by changing its deposition electrolyte concentration, temperature, and current density. Firstly, the ZnO is deposited on n-type Si substrate by electrodeposition by different deposited temperature, electrolyte concentration, and current density. The deposited films contain zinc nitrate, metal Zn, and ZnO while electrodeposited at various deposition parameters. For the deposited film contains only ZnO, no UV light is found measured by macroscopic photoluminescent analysis even annealed at different ambient and temperature. According to previous papers, an ideal UV light intensity can be obtained by thermal treated metal Zn or Zn ion implantation into oxide materials after annealing. Annealing the Zn-ZnO structure formed in 30oC by electrodeposition can observe intense UV light. This method improves the disadvantages of insufficient light intensity and no UV light observation from conventionally electrodeposited ZnO. The variation of UV light wavelength of ZnO oxidized from metal Zn is associated with the quantum-confinement effect that was discussed by previous papers. It is found that the size of ZnO is not small enough to realize the quantum-confinement effect, herein, we suggest that the variation of UV light wavelength is affected by the metal Zn resides in ZnO. Otherwise, the electrodeposition of ZnO is not easily performed on p-type substrate, an aluminum film on the back side of p-type Si can deposit ZnO by smaller potential, and different ZnO nanostructures are obtained by modifying the current density. Recently, different characteristics were found in nano-size noble metal crystals. In this thesis, the porous structure of Au-ZnO and Pt-ZnO were co-deposited by electrodeposition to enhance the photocatalytic activity. Si is the dominant material in semiconductor technology, but its indirect band gap property makes it not allowed in optoelectronics application. However, since 1990, the visible light is observed from porous Si fabricated by electrochemically etching of Si; though the light mechanism of porous Si is not clear, it can be divided into two parts, the quantum-confinement effect of Si nanocrystals and surface states on porous Si. Porous Si emits efficient visible light, but its light wavelength is readily influence by environment. We developed three methods, electrochemically etching the pre-treated Si substrate, adding chemical solution into electrolyte during etching process, and post-treatment of Si substrate after etching to prevent the emission of porous Si from being affected by environment.

Today, with increasing global awareness and regulation of air pollution, interest in the smog-abating property of photocatalytic materials is increasing. Titanium dioxide (TiO2) is the most well known photocatalytic semiconductor and is often considered as one way of solving pollution by a passive but an effective way, particularly to reduce atmospheric nitrogen oxides (NOx=NO+NO2). This relatively new technology is already being used in some of the countries as a construction material, commercially sold as photocatalytic cement, photocatalytic pavement, self-cleaning tiles, and self-cleaning glass. Prior research has examined the photocatalytic properties of TiO2 itself, as well as TiO2-containing cement-based materials. The majority of this effort has been on characterizing and enhancing the photocatalytic efficiency. However, relatively little research was performed to assess the potential impact of the photocatalytic reaction on the "parent" or "host" material. In this research, the focus is on the effect of photocatalysis on the composition, structure, and properties of cementitious materials, which contain titania nanoparticles at early and late ages. Fundamental examinations on the addition of these chemically non-reactive nanoparticles to cement-based materials are performed. The high surface area of nanoparticles could alter early age properties of cementitious materials, such as setting time, dimensional stability, and hydration rate. Various experimental techniques as well as mathematical modeling were used to examine and explain the early age hydration of cementitious materials when TiO2 nanoparticles are present. Further, the effects of the TiO2 on the long term durability of cement-based materials are investigated to demonstrate their suitability for long-term use in the field. The photocatalytic NOx oxidation efficiency and NOx binding capability of TiO2 containing cementitious materials are experimentally investigated. The durability of TiO2-cement is examined by various techniques on samples that went through extensive photocatalysis and environmental exposures. These investigations have led to tentative conclusions on the use of TiO2 nanoparticles in cementitious materials, and suggest avenues for future study.

Thesis (Ph. D.)--Ohio State University, 2009. / Title from first page of PDF file. Includes bibliographical references (p. 268-291).

Titanium Dioxide (TiO 2) has been considered an ideal photocatalyst due to factors such as its photocatalytic properties, chemical stability, impact on the environment and cost. However, its application has been primarily limited to ultraviolet (UV) environments due to its high band gap (3.2 eV). This high band gap limits the harvesting of photons to approximately 4% of sunlight radiation. Research today is focused on lowering this gap by doping or coupling TiO 2 with other semiconductors, transition metals and non-metal anions, thereby expanding its effectiveness well into the visible range. This thesis explores the effects of thermal and thermochemical ammonia treatment of nano-particulated TiO 2. The objective is to synthesize a photocatalytic activity in the visible range while at the same time retaining its photocatalytic properties in the UV range. Specifically, this study utilizes pure commercial nano-particulated TiO 2 powder (Degussa P-25), and uses this untreated TiO2 as a baseline to investigate the effects of thermal and thermochemical treatments. Nitrogen-doping is carried out by gas phase impregnation using anhydrous ammonia as the nitrogen source and a tube furnace reactor. The effects of temperature, time duration and gas flow rate on the effectiveness of thermally and thermochemically treated TiO 2 are examined. Thermally treated TiO 2 was calcinated in a dry inert nitrogen (N2) atmosphere and the effects of temperature and treatment duration are investigated. The band gap of the thermally treated and thermochemically ammonia treated TiO 2 have been measured and calculated using an optical spectrometer. The photocatalytic properties of all materials have been investigated by the degradation of methyl orange (MO) in an aqueous solution using both visible simulated solar spectrum (VSSS) and simulated solar spectrum (SSS) halogen light sources. Methyl orange degradation has been measured and calculated using an optical spectrometer. The phase structure and particle size of the materials is determined using x-ray diffraction (XRD). The BET surface area of the samples has been obtained using an Autosorb. Surface or microstructure characterization has also been obtained by scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Photocatalysis is a promising technique for the remediation of indoor air pollution. Photocatalysis utilizes semiconductor photocatalysts (such as TiO2 or ZnO) and appropriate light to produce strong oxidizing agents (OH*) that are able to break down organic compounds and inactivate bacteria and viruses. The overall goal of the research is to develop an efficient photocatalytic reactor based on mass transfer for indoor air purification. This study has focused on the enhancement of the effectiveness of the photocatalytic process by the introduction of artificial roughness on the reactor catalyst surface. The major effect of artificial roughness elements on the catalytic surface is to create local wall turbulence and enhance the convective mass transfer of the contaminants to the catalyst surface and thus lead to an increase in the effectiveness of photocatalysis. Air flow properties in a model photoreactor channel with various roughness patterns on the interior wall surface were theoretically investigated. The optimum shapes, sizes, and arrangements of roughness were determined for the maximum enhancement of turbulence intensity in the channel. The possible order of photocatalytic reactor performance for various roughness patterns was also determined. In order to verify the theoretical analysis results, experimental studies were carried out. A plate type photocatalytic reactor was designed and fabricated on the basis of the theoretical results. It was determined that the photocatalytic reactor performance is greatly improved with various rough catalyst surfaces. The experimental results verified the theoretical results. The relationship between the overall reaction rate constant (k) of the reactor and the magnitude of the turbulence intensity was found out. An empirical correlation expression was also proposed. This is the first study of the effect mass transfer in a rough catalytic surface for photocatalytic reactor. Photocatalyst development has also been studied. Zinc oxide (ZnO) and iron doped zinc oxide (ZnO/Fe) nanowires were synthesized on glass substrates through a conventional hydrothermal method. The photocatalytic activities under ultraviolet (UV) light and white light irradiation were separately investigated. The ZnO/Fe nanowires exhibited an enhanced photocatalytic activity as compared to ZnO nanowires regardless of the type of contaminants and light sources.