EN The thesis is focused on a speciation analysis of arsenic with use of the hydride generation - cryotrapping - gas chromatography - atomic absorption spectrometry. The aim of this project was the development of a method and instrumentation of the speciation analysis of arsenic based on combination of selective generation of substituted hydrides with a detection by atomic absorption spectrometry and with use of the cryotrapping of generated arsenic species and their separation by the gas chromatography. In the first part of this work the effects of individual parameters which influence the separation in the gas chromatograph were studied. Especially, time of injection from the cryotrap into GC, temperature program, carrier gas flow and carrier gas flow through a "deanswitch". Optimization of these parameters is an attempt to achieve a satisfactory resolution of the individual peaks of arsenic species separated by gas chromatography. Furthermore, an adequate sensitivity of this method is required to be achieved in comparison to other methods that use AAS detection such as a combination of hydride generation with cryotrapping. For this reason, the detection limits and the quantification of arsenic species were important to be determined as well. A sampling coil was replaced by a sampling tip...

This Master thesis is a part of a project: Hydride atomizers for atomic absorption and atomic fluorescence spectrometry - new horizons (GA ČR, P206/17-04329S, principal investigator: prof. RNDr. Jiří Dědina, CSc. DSc.) of which the general target is to make a leap towards the ideal hydride atomizer by optimization of atomization based on the knowledge of the distribution of free atoms and hydrogen radicals inside the atomizers. This thesis contributes to the project by optimizing the atomization parameters for atomic absorption spectrometry with hydride generation. The atomization parameters were optimized for three different types of atomizers - multiatomizer, diffusion flame and "flame-in-gas-shield" atomizer using three different analytes - bismuth, lead and tin. Optimal atomization parameters were found for each of the atomizer and each of the analyte - carrier gas flow and flow of other gases if needed for the analysis. Calibration curves and analytical figures of merit such as sensitivity, LOD and LOQ were estimated. Final comparison is based on the data obtained from calibration curves. MDF and FIGS atomizers are mostly used with AFS detection and they provide lower sensitivity and higher detection limits with AAS detection in comparison with MMQTA. Since the analytes are known to trap...

Generation and atomization of cadmium volatile compounds was optimized in this work in order to determine trace Cd concentration levels by volatile compound generation (VCG) with subsequent detection by atomic absorption spectrometry (AAS). Three designs of volatile compound generators have been tested including a conventional hydride generator in flow injection analysis (FIA) mode, a batch generator as well as a generator of volatile compounds of transition metals. The generation efficiency of Cd species was quantified as low as 4 % in the conventional hydride generator. Providing that dissolved oxygen was removed from the reaction solutions, the generation efficiency of Cd increased to 12 % in the same experimental arrangement. The highest Cd generation efficiency of 54 % was reached in the generator of volatile compounds of transition metals. In this set up a detection limit of 0.07 ng ml-1 Cd and a sensitivity of 3.2 s ng-1 Cd, respectively, were reached. Moreover, the structure of the volatile Cd species generated was identified as free atoms in all experimental arrangements of the generators investigated. Keywords atomic absorption spectrometry, cadmium, generation of volatile compounds, atomization of volatile compounds

Commercially available organic and conventionally grown vegetables were studied by quantitative determination of selected metals in them and to determine if any differences found are statistically significant. These findings can help the consumers to determine if the vegetable products are within the recommended maximum limits as proposed by the joint FAO/WHO Expert committee on organic foods designation. Eight edible vegetables were purchased from local stores in both the organic and conventionally grown categories. Samples were digested with concentrated nitric acid and the metals monitored were zinc, copper, lead, iron, cadmium, and nickel using flame atomic absorption. The concentration range for the heavy metals found are as follows: Zn, 2.04-69.4; Cu, 0.35-15.1; Pb, 0.00-3.99; Cd, 0.00-0.74; Fe, 2.52-319; and Ni, 39.9-53.8 μg/g. It was found that in general, conventional vegetables contain higher amounts of most of the heavy metals studied as compared to their organic counterparts. The study also showed that all vegetables products contain below the permissible limits for Zn, Cu, Ni, and Fe. For Pb all vegetables exceeded the safe limit except organic cucumber and conventional cabbage. For Cd, organic lettuce and green pepper, and conventional leafy green, green pepper, and spinach all exceeded the limit recommended by FAO/WHO.

This thesis is focused on increasing the senstitivity of gold determination by electrochemical volatile species generation using two different types of electrolytic cells in continuous flow setting. Externally heated quartz tube atomizer was used as means of atomization and detection of gold with atomic absorption spectrometer. Generation parameters were optimized for electrolytic cell with an ion exchange (nafion) membrane. After selection of new cathode material (Cu) the carrier gas (Ar) flow rate was optimized, where an additional inlet of carrier gas was found to have possitive effect on increasing the sensitivity of determination of gold and efficiency of volatile specie transport to the atomizer. Experiments with Antifoam B showed possitive effect on generation, thus calibration was carried out for optimized experimetal conditions reaching detection limit of 0,53 mg.dm−3 . The efficiency of volatile specie transfer from liquid to gaseous phase was determined between 60 - 65 % by measuring the residual gold content in liquid waste by F-AAS method. Subsequently the effieciency of electrolytic generation of volatile gold specie with radioactive tracer isotopes and autoradigraphy was determined to 0,6 %. These methods confirmed adsorption of generated species on apparatus surface. Using ICP-MS as...

A determinação direta de arsênio total em águas por espectrometria de absorção atômica com filamentos de tungstênio (150 W) modificados quimicamente com irídio ou ródio, representa uma alternativa para a atomização eletrotérmica de arsênio, que foi avaliada na presente dissertação. A utilização do revestimento com Ir como modificador químico proporcionou um aumento da massa característica de arsênio de 3,5 vezes. As medidas foram feitas com altura de observação selecionada para proporcionar a melhor razão sinal/ruído sem diminuir a sensibilidade do sinal analítico. Avaliaram-se dois programas de aquecimento: com temperatura de secagem constante (com diminuição gradativa da tensão aplicada) e com temperatura de secagem variável (com tensão aplicada de maneira constante). Não houve diferença na sensibilidade entre os dois programas estudados, indicando que a modificação química leva à formação de um precursor atômico com estabilidade térmica elevada. De fato, utilizando-se a modificação química permanente com 1000 müg Ir, e adotando-se programa de aquecimento com temperatura de secagem variável, a temperatura máxima de pirólise foi de aproximadamente 1700 °C ( temperatura de atomização de 2700 °C). Avaliou-se o comportamento eletrotérmico do As na presença dos concomitantes Na, K, Ca e Mg em 0,1% v/v HNO3. Interferências mais severas foram observadas na presença de cálcio acima de 10 \'mü\'g l-1, e acima de 100 \'mü\'g l-1 para os demais concomitantes. As interferências podem estar relacionadas com o elevado gradiente de temperatura entre a superfície do filamento e a fase gasosa do volume de observação, ou mesmo devido à formação de compostos refratários, particularmente para Ca e Mg, na fase condensada, ou seja, na superfície do atomizador. O emprego do método das médias móveis no tratamento dos sinais transientes gerados na atomização do arsênio também foi avaliada. Com o filamento posicionado na altura de observação 2 mm, foram utilizados os fatores 0, 3, 5, 7 e 9, observando-se melhora considerável nos limites de detecção instrumental e do método,utilizando-se média móvel com fator 7. Nestas condições, e depositando-se 20 \'mü\'l de amostra sobre o filamento, o limite de detecção foi de 3,2 \'mü\'g l-1 As e a massa característica de 37,0 pg As. A exatidão foi avaliada analisando-se diferentes amostras de águas provenientes da região do Quadrilátero Ferrífero do Estado de Minas Gerais, por espectrometria de fluorescência atômica com geração de hidretos e por espectrometria de absorção atômica com o filamento de tungstênio modificado com Ir. A comparação dos resultados mostrou que o método proposto pode ser utilizado para o controle de qualidade de águas desta região. Aproximadamente 150 queimas podem ser feitas com um único filamento de tungstênio / The direct determination of arsenic in waters by atomic absorption spectrometry with 150 W tungsten coils, treated with Ir or Rh, was evaluated as a possible alternative for the eletrothermal atomization of As. The use of iridium as a permanent chemical modifier did improve the characteristic mass of arsenic by 3.5 fold. Measurements were made by choosing an appropriate observation height in order to get the best signal to noise ratio. Two heating programs were tested, either by keeping the applied voltage constant or by using an inverted voltage ramp during the drying step. There were no significant differences in the sensitivities between both heating programs, indicating that the permanent modification lead to the formation of an atomic precursor of high thermal stability. Indeed, with the permanent chemical modification with 1000 \'mü\'g Ir, the maximum pyrolysis temperature was approximately 1700 °C (atomization temperature 2700 °C), allowing a heating program with temperature variation during the drying step. Method selectivity was carried out by evaluating the eletrothermal behavior of As in the presence of up to 1000 \'mü\'g l-1 Na, K, Ca and/or Mg in 0,1% v/v HNO3. The most serious interferences were observed with Ca in concentrations higher than 10 \'mü\'g l-1 and when the concentrations were higher than 100 \'mü\'g l-1 for Na, K or Mg, which can be attributed either to the gradient of temperature between the surface of the atomizer and the observation volume or to the formation of refractory compounds in the condensed phase, particularly with Ca and Mg. The absorbance transient signals treatment by the method of moving averages up to factor 9 was also evaluated, with a remarkable improvement in the instrumental and method detection limits. With the center of the observation volume 2 mm above the tungsten coil surface, and a moving average of factor 7, the limit of detection was 3,2 \'müg\' l-1 As and the characteristic mass 37,0 pg As. Accuracy was evaluate by analysing water samples collected in a contaminated area from the Quadrilátero Ferrífero, Minas Gerais State, by hydride generation atomic fluorescence spectrometry and by tungsten coil eletrothermal atomic absorption spectrometry. Results showed that the proposed method fits for the purpose of CONAMA 357 regulation for drinking water quality in the aforementioned contaminated area. Approximately 150 firings can be done with a single tungsten coil atomizer by using 20 \'mü\'l sample volume

Um método de baixo custo é proposto para determinação direta de chumbo em açúcar por espectrometria de absorção atômica com forno de grafite e correção de fundo com fonte de deutério, empregando modificação química permanente com 250µg W + 200µg Rh e co-injeção de 5µg Rh. Os experimentos foram realizados com plataforma integrada ou ao no tubo de grafite com aquecimento longitudinal. Para avaliação da modificação química permanente, foram feitos experimentos na ausência de modificação e na presença de modificação química convencional com Pd+Mg. No decorrer do trabalho observou-se ser imprescindível a co-injeção de Rh para a estabilização térmica de chumbo na presença de açúcar. A amostra (8 g) é dissolvida em 100 ml de solução aquosa 0,2% v/v HNO3, e uma alíquota de 10 l é injetada com 5µl de solução de Rh na plataforma do tubo de grafite modelo Universal da Varian tratada com W e Rh. A massa característica (mo) e o limite de detecção do método foram 11 pg Pb e 5 ng g-1 respectivamente, e a vida útil do tubo de grafite foi de 860 queimas. O método apresentou boa reprodutibilidade com coeficiente de variação inferior a 2,5 % (n=3). As características analíticas foram comparadas com os métodos recomendados na literatura. A exatidão do método proposto para determinação direta de chumbo em açúcar foi avaliada pela comparação com método convencional utilizando Pd+Mg e nenhuma diferença estatística foi observada aplicando-se o teste t de Student ao nível de 95% de probabilidade, em amostras que receberam adição de chumbo / A simple method for the direct determination of lead in sugar by graphite furnace atomic absorption spectrometry (GFAAS) with platform treated with 250µg W + 200µg Rh and deuterium background correction is proposed. Samples (8 g) were dissolved in 100 ml of an aqueous solution containing 0,2% v/v HNO3 and 10µl aliquots were co-injected with 5µg Rh into the integrated platform modified with W-Rh of the Universal Varian longitudinal heated graphite atomizer. The characteristic mass (mo) and the method detection limit were 11 pg Pb and 5,0 ng g-1 Pb, respectively, and the tube life time was 860 firings. The relative standard deviation of measurements (n=3) was lower than 2,5 %. For the evaluation of the permanent chemical modifier, parallel experiments were carried in the presence of diluted nitric acid and with the conventional Pd+Mg chemical modifier. Experiments were made either with manual inserted graphite plataforms or integrated plataforms into longitudinal graphite tubes. Comparison of the proposed method with a method based on Pd+Mg chemical modifier showed no statistical differences by applying a t-test at 95% confidence level, for sugar sample solution spiked with lead

A constante de solubilidade do azoteto de prata, AgN3, foi avaliada por meio da sua solubilidade em água. A concentração de prata foi determinada em solução saturada de azoteto de prata a 25ºC utilizando a técnica de Espectrometria de Absorção Atômica com Chama obtevendo-se um valor de (2,7 ± 0,2) x10-5 mol L-1 com 95% de confiança. A concentração de prata foi também determinada pela técnica Potenciométrica utilizando eletrodo de prata metálica tratado previamente com solução saturada diluída de AgN3 e a solubilidade obtida foi de (2,43 ± 0,09) x10-5 mol L-1 com 95% de confiança. As constantes de solubilidade calculadas pela equação Ks = (solubilidade )2 foram (7,3 ± 0,1) x 10-10 mol2 L-2 por Espectrometria de Absorção Atômica com Chama e (5,9 ± 0,1) x10-10 mol2 L-2 por Potenciometria. Esses valores de constante de solubilidade estão vinculados ao tamanho da partícula do precipitado de (27 ± 2) &#181;m. O grau de hidrólise do ânion azoteto foi avaliado medindo-se a variação de pH da água antes e após a saturação com o precipitado de azoteto de prata. A variação foi avaliada em (1,2 ± 0,6) x10-7 mol L-1 em relação à concentração de hidroxila liberada pela protonação do azoteto, valor este que se situou abaixo da variação da incerteza avaliada na solubilidade, razão pela qual não teve influência significativa (<0,5%). / The solubility constant of the silver azide, AgN3, was determined through its solubility in water. The concentration of silver was determined by a saturated solution of silver azide at 25 ºC with the Flame Atomic Absorption Spectrometer having a value of (2,7 ± 0,2) x 10-5mol L-1 with 95% of confidence. The concentration of silver was determined also by Potenciometric technical with an electrode of metallic silver previously treated with a saturated solution diluted of silver azide and the solubility obtained was (2,43 ± 0,09) x 10-5mol L-1 with 95% of confidence. The solubility constant calculated by the equation Ks = (solubility)2 were (7,3±0,1)x10-10 mol2 L-2 by FAAS and (5,9±0,1)x10-10 mol2L-2 by Potenciometry. These values of solubility constants are connected with the size of the precipitate of the (27 ± 2) &#181;m. The hidrolisys degree of the anion azide was determined trough the measuring of pH of pure water and pH after the saturation of water with the precipitate of silver azide. The variation was determined was (1,2 ± 0,6) x 10-7mol L-1 in terms of the concentration of hydroxyl liberated trough the protonation of azide. This value was lower than the uncertainty associated with the solubility of AgN3. In this way it was not taken in account (<0,5%).

Este trabalho teve por objetivo estudar a capacidade da remoção da camada de smear das paredes do canal radicular, pelas soluções de EDTA a 15%, ácido cítrico a 10%, citrato de sódio a 10%, vinagre de maçã, ácido acético a 5%, ácido málico a 5% e hipoclorito de sódio a 1% por meio da microscopia eletrônica de varredura e quantificar a concentração de ions cálcio presentes nessas soluções após suas utilizações, por meio da espectrofotometria de absorção atômica de chama. Utilizaram-se 42 dentes incisivos centrais superiores, nos quais se realizou a cirurgia de acesso, remoção de ombro cervical e desgaste compensatório. Aferiu-se o comprimento de trabalho com uma lima tipo K, diâmetro #10 introduzida no canal radicular de cada dente até ser visualizada no ápice, subtraindo-se um milímetro. Determinou-se também o diâmetro anatômico do canal do dente no comprimento de trabalho por meio da introdução de instrumentos tipo K da primeira série com diâmetros sucessivamente maiores, que foi anotado quando um dos instrumentos sofresse resistência ao ser retirado do comprimento de trabalho. Todos os dentes que apresentaram diâmetro anatômico do canal acima de 40 centésimos de milímetros foram descartados e repostos por outros. Desta forma, garantiu-se o desgaste de 20 centésimos de milímetros no terço apical. A técnica utilizada foi a Free Tip Preparation (PECORA et al. 2002) até que um instrumento de diâmetro #60 e taper .04 percorresse todo o comprimento de trabalho. Utilizou-se a solução de hipoclorito de sódio a 1,0% durante todo o preparo biomecânico. Os dentes tiveram seus canais radiculares lavados com 20 mililitros de água deionizada para a remoção de possíveis raspas de dentina soltas no interior do canal radicular. Após o término do preparo biomecânico, os dentes foram divididos aleatoriamente em 7 grupos de 6 dentes cada, de acordo com a substância química utilizada para a irrigação final, a saber: G1 - solução de EDTA a 15,0%; G2 - solução de ácido cítrico a 10,0%; G3 - solução de citrato de sódio a 10,0%; G4 - vinagre de maçã; G5 - solução de ácido acético a 5,0%; G6 - solução de ácido málico a 5,0% e G7 - sem irrigação final (controle negativo). O tempo de permanência das soluções nos canais radiculares foi de 5 minutos. Os dentes foram clivados no sentido vestíbulo-palatino e encaminhados para a microscopia eletrônica de varredura, em que se obtiveram fotomicrografias com o aumento de 1000 vezes. As soluções coletadas foram encaminhadas para a análise química, realizada com um espectrofotômetro de absorção atômica de chama. Concluiu-se que o EDTA a 15% e o ácido cítrico a 10% são eficientes para a remoção da camada de smear. O vinagre de maçã, o citrato de sódio a 10%, os ácidos acético e málico a 5% e o hipoclorito de sódio não foram eficientes para a mesma finalidade. O EDTA a 15% apresentou a maior concentração de ions cálcio em solução; o ácido cítrico a 10% ficou na segunda posição e a terceira foi ocupada pelo vinagre de maçã e os ácidos acético e málico a 5%. A menor concentração de íons cálcio foi encontrada no citrato de sódio a 10%. / This study evaluated the smear layer removal capacity of 15% EDTA, 10% citric acid, 10% sodium citrate, apple vinegar, 5% acetic acid and 1% sodium hypochlorite using scanning electron microscopy and flame atomic absorption spectrophotometry. Forty two central superior incisives were used. On these teeth, it were accomplished the access surgery, removal of cervical shoulder and compensatory wear. The working length was checked with a #10 K-type file that was introduced in the radicular canal of each tooth until be visualized at the apex, then a millimeter was subtracted. The anatomical diameter of the canal in the working length was also determined through the introduction of K-type instruments of the first series with successively larger diameters. The anatomical diameter of the radicular canal was notated when one of the instruments showed resistance to be removed from the working length. All the teeth that presented the canal diameter in the working length above 40 hundredths millimeters were discarded and replaced by other. This way, it was obtained a standard wear of 20 hundredths millimeters in the apical third. The Free Tip Preparation technique (PECORA et al. 2002) was used until a #60- diameter instrument and .04 taper reached the entire working length. The 1.0% sodium hypoclorite solution was used during biomechanical preparation. The teeth had their radicular canals washed with 20 milliliters of deionized water, using Milli-Q® water purification system, for removal of possible dentine chips presented inside the root canal. After the biomechanical preparation, the teeth were randomly divided into 7 groups of 6 teeth each: group 1: teeth with final irrigation with 15% EDTA solution, group 2: teeth with final irrigation with 10%citric acid solution, group 3: final irrigation with 10% sodium citrate solution, group 4: final irrigation with apple vinegar, group 5: final irrigation with 5% acetic acid solution, group 6: final irrigation with 5% maleic acid solution and group 7: teeth only instrument and irrigated with sodium hypochlorite, without final irrigation. Each solution remained 5 minutes in the radicular canal. The cleavage of teeth was done in buccal-palatine direction and they were subjected to the scanning electron microscopy and photographed at 1000X. The collected solutions were submitted to chemical analysis through flame atomic absorption spectrophotometry. It was concluded that 15% EDTA and 10% citric acid, used for 5 minutes, are effective in removing the smear layer. The apple vinegar, 10% sodium citrate, 5% acetic and maleic acids and sodium hypochlorite were not effective in removing the smear layer from root canal. 15% EDTA presented a higher concentration of calcium ions in solution, followed by 10% citric acid. Intermediary results were observed by apple vinegar, 5% acetic and maleic acids, and the inferior concentration of calcium ions was obtained with the 10% sodium citrate.

No presente trabalho foram desenvolvidos métodos analíticos para a determinação de As, Cd, Cr, Hg e Pb em embalagens celulósicas para alimentos por espectrometria de absorção atômica com atomização em forno de grafite e amostragem direta de sólidos (SS-GF AAS). Para a determinação direta de Hg, a solução de KMnO4 e a mistura oxidante (HNO3 + H2SO4) com a plataforma e parede interna do tubo modificadas com Pd apresentaram os melhores resultados. A mistura oxidante promoveu o pré-tratamento térmico in situ do papel, reduzindo o sinal de fundo. Foi investigada a viabilidade de empregar papéis de filtro, impregnados com concentrações conhecidas dos analitos e moídos por moagem criogênica, como padrões sólidos para calibração do equipamento. Os padrões sólidos produzidos apresentaram boa homogeneidade para As, Cd, Hg e Pb, adequada para microanálises e submicroanálises. Não foi desenvolvido método para determinação direta de Cr devido à contaminação durante a etapa de moagem. Foram construídas curvas analíticas de calibração utilizando-se massas crescentes de um único padrão sólido e massas similares dos padrões contendo diferentes concentrações dos analitos. As curvas obtidas foram concordantes em termos de coeficientes angulares, com razões de aproximadamente 1, indicando que ambos procedimentos de calibração podem ser empregados para SS-GF AAS. Materiais de referência certificados de matriz vegetal foram analisados para avaliar a exatidão dos métodos propostos empregando-se as curvas obtidas. Os resultados para As, Cd e Pb apresentaram boa exatidão e precisão. Os limites de detecção encontrados para a análise direta de sólidos foram: 0,36 &#181;g g-1 para As, 4,0 ng g-1 para Cd, 0,46 &#181;g g-1 para Hg e 0,036 &#181;g g-1 para Pb. O emprego dos métodos desenvolvidos na determinação direta de As, Cd, Hg e Pb em amostras de embalagens celulósicas para alimentos indicou que estes podem ser utilizados no controle de qualidade dessas embalagens, apresentando boa sensibilidade, precisão e exatidão. As concentrações de Cd e Pb nas embalagens analisadas variaram, respectivamente, de 0,015 a 0,099 &#181;g g-1 e de 0,05 a 6,70 &#181;g g-1. As concentrações de As e Hg nas embalagens ficaram abaixo dos limites de detecção. Foi possível a determinação de Cr nos digeridos de pedaços das embalagens, obtendo-se concentrações de 1,8 a 4,1 &#181;g g-1. / In the present work analytical methods for determination of As, Cd, Cr, Hg and Pb in paper and board food packaging materials by solid sampling graphite furnace atomic absorption spectrometry (SS-GF AAS) were developed. For direct determination of Hg, the best results were achieved using KMnO4 solution and an oxidant mixture (HNO3 + H2SO4) in combination with the graphite platform and inner wall of graphite tube modified with palladium as permanent modifier. The oxidant mixture allowed the \"in situ\" thermal pretreatment, reducing the background signals. The feasibility of using cryogenic ground spiked filter papers with different concentrations of the analyte as synthetic calibrating standards was investigated. The calibrating standards showed good homogeneity for As, Cd, Hg and Pb being suitable for both microanalysis and submicroanalysis. The method for the direct determination of Cr was not developed due to the contamination during the grinding step. The analytical calibration curves were made by increasing masses of one calibrating standard and similar masses of the calibrating standards containing different concentrations of the analyte. The ratio between slopes of analytical curves were approximately 1 for As, Cd, Hg e Pb, indicating the adequacy of using both calibrating procedures for SS-GF AAS. Vegetable certified reference materials were analyzed to evaluate the accuracy of the proposed methods. The results for As, Cd e Pb presented good accuracy and precision. The detection limits for the solid sample analysis were: 0,36 &#181;g g-1 for As, 4,0 ng g-1 for Cd, 0,46 &#181;g g-1 for Hg and 0,036 &#181;g g-1 for Pb. The direct determination of As, Cd, Hg and Pb in paper and board food packaging material samples were successfully done indicating that the developed methods can be employed in the quality control of these samples with good sensibility, precision and accuracy. The concentration of Cd and Pb in analyzed packaging materials ranged from 0,015 to 0,099 &#181;g g-1 and from 0,05 to 6,70 &#181;g g-1, respectively. The concentration of As and Hg in packaging materials were below to the detection limits. It was possible the determination of Cr in solution after pieces of packaging materials digestion. The concentrations of Cr ranged from 1,8 to 4,1 &#181;g g-1.