There are several standards for wireless communication. People that are involved in computers and networking recognize names like Bluetooth, HiperLAN and IEEE 802.11. A fundamental part of an IEEE 802.11 node is the Medium Access Controller. It establishes and controls communication with other nodes, using a physical layer unit. This is the work that was carried out as a master thesis project at Ericsson Microelectronics. The main goal was to design, implement and evaluate a hardware interface between the MAC and the physical layer. An important part of the work was to find a suitable partition scheme for hardware and software and to achieve this, an investigation of processor-cycles usage was carried out to support design decisions. The hardware/software partition resulted in hardware-functionality for decode of received frames and automatic transmission of acknowledge frames.

Kraven på dagens trådlösa förbindelser kommer hela tiden att öka och med detta följer även högre krav på nya produkter som kan tillgodose de ökade kraven. För att göra processen från idé till produkt snabbare krävs enkla verktyg för att snabbt kunna gå från den formulerade standarden till en hårdvaruprototyp. Detta arbete har använt sig av ett av dessa verktyg som idag finns tillgängliga, Xilinx System Generator for DSP 1.1, för att ta fram sändare och mottagare för en del av den trådlösa standarden IEEE 802.11a. Arbetet ger en beskrivning av hur sändare och mottagare är uppbyggda samt även synpunkter på System Generator och beskrivningar av problem som uppstod under arbetet. / The demands on todays wireless communications will continue to increase and with this follows a demand for shorter and shorter development times for the products that are going to satisfy this demand. To accomplish this shorter development time simple tools for going from the formulated standard to a hardware prototype is needed. This work uses one of these tools today available, Xilinx System Generator for DSP 1.1, to develop a transmitter and a reciever for a part of the wireless standard IEEE 802.11a. The work gives a description of the building blocks of the transmitter and the reciever but also some views on System Generator and descriptions of problems that were encountered during the work.

This thesis is analysis-based survey in which our task was to find out the suitability of IEEE 802.15.4 for the RFID systems in terms of power. We studied the different RFID systems. We analyzed the IEEE 802.15.4 to see how much this protocol can facilitate the RFID application, but we just considered the 2.4 GHz physical band as Free2move uses this band for its RFID products. Since semi-passive1 RFIDs are the closest competitors of the active RFID, so we also compared the IEEE 802.15.4 with ISO 18000-4 (mode2) to find out their pros and cons. We also tried to evaluate the hardware architecture proposed by Free2move. We compared proposed hardware components with other competitors available in the market. The main point of focus during hardware evaluation remained its power efficiency. As concluding part we have proposed an idea for using the IEEE 802.15.4 standard in semi- passive RFIDs.

The need for higher data rates in WLANs boosts drastically because tremendous consumer interest in emerging multimedia applications, such as HDTV, has been increased. Currently, the IEEE 802.11a/b/g WLANs provide a limited data rate for the current user application requirements. In order to overcome substantial limitations of the existing WLANs, the next generation of WLANs, IEEE 802.11n, is in the course of development and expected to support higher throughput, larger coverage area and better QoS. The high performance IEEE 802.11n WLAN can improve data rate significantly by using smart antenna systems in the physical layer to take advantage of multi-path fading of wireless channels. In this thesis, an analytical model is developed to study the MAC performance and the underlying smart antenna technologies used in multi-path fading channels. Multiple antennas employed in the AP arise two popular approaches to provide a significant performance improvement, diversity and multiplexing. Considering the diversity gain of multiple antennas at the AP in which the AP with multiple antennas serves one user at a time, the capacity and throughput can be obtained. In addition, the AP is possible to serve multiple users in the downlink, by exploiting the multiplexing gain of the wireless channel. We investigate the maximum network throughput when the traffic intensity of the AP approaches to one. Unlike most of previous research which focus on either the physical or the MAC layer performance, our analytical model jointly considers the MAC protocol and the smart antenna technology.

With the exploding increase of mobile users and the release of new wireless applications, the high bandwidth requirement has been taking as a main concern for the design and development of the wireless techniques. There is no doubt that broadband wireless access with the support of heterogeneous kinds of applications is the trend in the next generation wireless networks. As a promising broadband wireless access standard, IEEE 802.16 has attracted extensive attentions from both industry and academia due to its high data rate and the inherent media access control (MAC) mechanism, which takes the service differentiation and quality of service (QoS) provisioning into account. To achieve service differentiation and QoS satisfaction for heterogenous applications is a very complicated issue. It refers to many fields, such as connection admission control (CAC), congestion control, routing algorithm, MAC protocol, and scheduling scheme. Among these fields, packet scheduling plays one of the most important roles in fulfilling service differentiation and QoS provisioning. It decides the order of packet transmissions, and provides mechanisms for the resource allocation and multiplexing at the packet level to ensure that different types of applications meet their service requirements and the network maintains a high resource utilization. In this thesis, we focus on the packet scheduling for difficult types of services in IEEE 802.16 networks, where unicast and mulitcast scheduling are investigated. For unicast scheduling, two types of services are considered: non-real-time polling service (nrtPS) and best effort (BE) service. We propose a flexible and efficient resource allocation and scheduling framework for nrtPS applications to achieve a tradeoff between the delivery delay and resource utilization, where automatic repeat request (ARQ) mechanisms and the adaptive modulation and coding (AMC) technique are jointly considered. For BE service, considering the heterogeneity of subscriber stations (SSs) in IEEE 802.16 networks, we propose the weighted proportional fairness scheduling scheme to achieve the flexible scheduling and resource allocation among SSs based on their traffic demands/patterns. For multicast scheduling, a cooperative multicast scheduling is proposed to achieve high throughput and reliable transmission. By using the two-phase transmission model to exploit the spatial diversity gain in the multicast scenario, the proposed scheduling scheme can significantly improve the throughput not only for all multicast groups, but also for each group member. Analytical models are developed to investigate the performance of the proposed schemes in terms of some important performance measurements, such as throughput, resource utilization, and service probability. Extensive simulations are conducted to illustrate the efficient of the proposed schemes and the accuracy of the analytical models. The research work should provide meaningful guidelines for the system design and the selection of operational parameters, such as the number of TV channels supported by the network, the achieved video quality of each SS in the network, and the setting of weights for SSs under different BE traffic demands.

This thesis contributes toward the design of a quality-of-service (QoS) aware network layer for wireless ad hoc networks. With the lack of an infrastructure in ad hoc networks, the role of the network layer is not only to perform multihop routing between a source node and a destination node, but also to establish an end-to-end connection between communicating peers that satisfies the service level requirements of multimedia applications running on those peers. Wireless ad hoc networks represent autonomous distributed systems that are infrastructure-less, fully distributed, and multi-hop in nature. Over the last few years, wireless ad hoc networks have attracted significant attention from researchers. This has been fueled by recent technological advances in the development of multifunction and low-cost wireless communication gadgets. Wireless ad hoc networks have diverse applications spanning several domains, including military, commercial, medical, and home networks. Projections indicate that these self-organizing wireless ad hoc networks will eventually become the dominant form of the architecture of telecommunications networks in the near future. Recently, due to increasing popularity of multimedia applications, QoS support in wireless ad hoc networks has become an important yet challenging objective. The challenge lies in the need to support the heterogeneous QoS requirements (e.g., data rate, packet loss probability, and delay constraints) for multimedia applications and, at the same time, to achieve efficient radio resource utilization, taking into account user mobility and dynamics of multimedia traffic. In terms of research contributions, we first present a position-based QoS routing framework for wireless ad-hoc networks. The scheme provides QoS guarantee in terms of packet loss ratio and average end-to-end delay (or throughput) to ad hoc networks loaded with constant rate traffic. Via cross-layer design, we apply call admission control and temporary bandwidth reservation on discovered routes, taking into consideration the physical layer multi-rate capability and the medium access control (MAC) interactions such as simultaneous transmission and self interference from route members. Next, we address the network-layer resource allocation where a single-hop ad hoc network is loaded with random traffic. As a starting point, we study the behavior of the service process of the widely deployed IEEE 802.11 DCF MAC when the network is under different traffic load conditions. Our study investigates the near-memoryless behavior of the service time for IEEE 802.11 saturated single-hop ad hoc networks. We show that the number of packets successfully transmitted by any node over a time interval follows a general distribution, which is close to a Poisson distribution with an upper bounded distribution distance. We also show that the service time distribution can be approximated by the geometric distribution and illustrate that a simplified queuing system can be used efficiently as a resource allocation tool for single hop IEEE 802.11 ad hoc networks near saturation. After that, we shift our focus to providing probabilistic packet delay guarantee to multimedia users in non-saturated IEEE 802.11 single hop ad hoc networks. We propose a novel stochastic link-layer channel model to characterize the variations of the IEEE 802.11 channel service process. We use the model to calculate the effective capacity of the IEEE 802.11 channel. The channel effective capacity concept is the dual of the effective bandwidth theory. Our approach offers a tool for distributed statistical resource allocation in single hop ad hoc networks, which combines both efficient resource utilization and QoS provisioning to a certain probabilistic limit. Finally, we propose a statistical QoS routing scheme for multihop IEEE 802.11 ad hoc networks. Unlike most of QoS routing schemes in literature, the proposed scheme provides stochastic end-to-end delay guarantee, instead of average delay guarantee, to delay-sensitive bursty traffic sources. Via a cross-layer design approach, the scheme selects the routes based on a geographical on-demand ad hoc routing protocol and checks the availability of network resources by using traffic source and link-layer channel models, incorporating the IEEE 802.11 characteristics and interaction. Our scheme extends the well developed effective bandwidth theory and its dual effective capacity concept to multihop IEEE 802.11 ad hoc networks in order to achieve an efficient utilization of the shared radio channel while satisfying the end-to-end delay bound.

Characteristics of wireless home and office services and the corresponding networking issues are discussed. Local Area Networking (LAN) and Personal Area Networking (PAN) technologies such as IEEE 802.11 and Ultra Wideband (UWB) are introduced. IEEE 802.11a and UWB systems are susceptible to interference from each other due to their overlapping frequencies. The major contribution of this work is to provide a framework for coexistence of the two systems. The interference between the two systems is evaluated theoretically by developing analytical models, and by simulations. It is shown that the interference from UWB on IEEE 802.11a systems is generally insignificant. IEEE 802.11a interference on UWB systems, however, is very critical and can significantly increase the bit error rate (BER) and degrade the throughput of the UWB system. A novel idea in the MAC layer is presented to mitigate this interference by means of temporal separation. Simulation results validate our technique. Implications to wireless home services such as high definition television (HDTV) are provided. Future research directions are discussed.

A circuit design of Low Density Parity Check (LDPC) decoder for IEEE 802.16e systems is with new overlapped method is proposed in this thesis. This circuit can be operated with 19 modes which are corresponding to block sizes of 576, ¡K, 2304. LDPC decoders can be implemented by using iterations with Variable Node and Check Node Processes. The hardware utilization ratio, which can be enhanced from 50% to 100% by using our proposed overlapped method, is better than traditional overlapped method. In [2], the traditional overlapped method utilization ratio just can be enhanced from 50% to 75% for IEEE 802.16e LDPC decoder with code rate 1/2. Under the same operating frequency, our proposed method can further increase 25% when compared with traditional overlapped method [2]. In this thesis, we also propose two circuit architectures to increase the operating frequency. First, we use a faster comparison circuit in our comparison unit [1]. Second, we use Carry Save Adder¡]CSA¡^method [8] to replace the common adder unit. The circuit is carried out by TSMC CMOS 0.18£gm 1P6M process with chip area 3.11 x 3.08 mm2. In the gate level simulation, the output data rate of this circuit is above 78.4MHz, so the circuit can meet the requirement of IEEE 802.16e system.

With the proliferation of mobile devices and the advance of audio/video coding technologies, there is an increasing demand to provide quality-of-service (QoS) guarantees for multimedia applications. A WLAN (wireless local are network) typically consists of an access point (AP) and a finite set of mobile stations. Since the AP is generally more powerful and less physical constraint than mobile stations, it is of great interest to consider the use of sectorized multi-beam antennas at the AP to boost the network throughput by exploiting the benefit of spatial reuse. IEEE 802.11 is current the de facto standard for WLANs. However, if we directly apply 802.11 to the WLAN with multi-beam AP without any modification, we will encounter many challenging problems. Although existing solutions modify the 802.11 DCF (distributed coordination function) to solve these problems, yet DCF does not provide any QoS support. On the basis of 802.11e HCCA (hybrid channel control access), in this thesis, we propose a novel MAC protocol, named MPCF (multi-beam AP-assisted point coordination function), which is not only backward compatible with DCF, but also supports QoS functionalities, including non-reversal prioritization, time-bounded reservation, admission control, and cross-layer rate adaptation for multimedia streaming. Simulation results show that, in terms of throughput, frame delay dropped rate, and energy throughput, MPCF significantly outperforms existing protocols even in imperfect beam-forming and mobility environments.

One of the major applications driving wireless network services is video streaming, which is based on the ability to simultaneously multicast the same video contents to a group of users, thus reducing the bandwidth consumption. On the other hand, due to slow progress in battery technology, the investigation of power saving technologies becomes important. IEEE 802.16e (also known as Mobile WiMAX) is currently the international MAC (medium access control) standard for wireless metropolitan area networks. However, in 802.16e, the power saving class for multicast traffic is designed only for best-effort-based management operations. On the other hand, SMBC-AMC adopts the concepts of ¡§multicast superframe¡¨ and ¡§logical broadcast channel¡¨ to support push-based multicast applications. However, SMBC-AMC requires that (1) the number of frames in each logical broadcast channel must be equal, (2) all mobile stations must have the same duty cycle, and (3) the base station must use the same modulation to send data in a frame. These imply that SMBC-AMC is too inflexible to reach high multicast energy throughput. In this thesis, we propose cross-layer energy efficient multicast scheduling algorithms, called EEMS-AMC, for scalable video streaming. The goal of EEMS-AMC is to find a multicast data scheduling such that the multicast energy throughput of a WiMAX network is maximum. Specifically, EEMS-AMC has the following attractive features: (1) By means of admission control and the restriction of the multicast superframe length, EEMS-AMC ensures that the base layer data of all admitted video streams can be delivered to mobile stations in timeliness requirements. (2) EEMS-AMC adopts the greedy approach to schedule the base layer data such that the average duty cycle of all admitted stations can approach to the theoretical minimum. (3) EEMS-AMC uses the metric ¡§potential multicast throughput¡¨ to find the proper modulation for each enhancement layer data and uses the metric ¡§multicast energy throughput gain¡¨ to find the near-optimal enhancement layer data scheduling. Simulation results show that EEMS-AMC significantly outperforms SMBC-AMC in terms of average duty cycle, multicast energy throughput, multicast packet loss rate, and normalized total utility.