Ion-exchange membranes, conventionally utilized in separation processes of electrolyte solutions, are electroactive polymers that display a unique coupling between electrochemistry and mechanics. Previous experimental studies have demonstrated the possibility of actuating cation-exchange membranes in salt solution through the application of a remote external electric field. The use of anion-exchange membranes as contactless actuators, however, has never been documented and little is known about the physics of their actuation. Here, it is reported for the first time the possibility of contactless actuating anion-exchange membranes in salt solutions; such an actuation is mediated by the selection of anions in the external salt solution and the membrane. Actuation is attributed to the physical phenomenon of solvation, the interaction between ions and solvent in solution. Contrary to previous studies with cation-exchange membranes, the results show that anion-exchange membranes consistently bend toward the anode. The integration of anion-exchange and cation-exchange membranes in composites promises innovative programmable contactless actuators, with applications in underwater robotics and biomedical engineering.

A piezoelectric impedance-based structural health monitoring technique was developed at the Center for Intelligent Material Systems and Structures. It has been successfully implemented on several complex structures to detect incipient-type damage such as small cracks or loose connections. However, there are still some problems to be solved before full scale development and commercialization can take place. These include: i) the damage assessment is influenced by ambient temperature change; ii) the sensing area is small; and iii) the ability to identify the damage location is poor. The objective of this research is to solve these problems in order to apply the impedance-based structural health monitoring technique to real structures. First, an empirical compensation technique to minimize the temperature effect on the damage assessment has been developed. The compensation technique utilizes the fact that the temperature change causes vertical and horizontal shifts of the signature pattern in the impedance versus frequency plot, while damage causes somewhat irregular changes. Second, a new impedance-based technique that uses multiple piezoelectric sensor-actuators has been developed which extends the sensing area. The new technique relies on the measurement of electrical transfer admittance, which gives us mutual information between multiple piezoelectric sensor-actuators. We found that this technique increases the sensing region by at least an order of magnitude. Third, a time domain technique to identify the damage location has been proposed. This technique also uses multiple piezoelectric sensors and actuators. The basic idea utilizes the pulse-echo method often used in ultrasonic testing, together with wavelet decomposition to extract traveling pulses from a noisy signal. The results for a one-dimensional structure show that we can determine the damage location to within a spatial resolution determined by the temporal resolution of the data acquisition. The validity of all these techniques has been verified by proof-of-concept experiments. These techniques help bring conventional impedance-based structural health monitoring closer to full scale development and commercialization. / Master of Science

This thesis performs closed-loop control of a 3D printed soft bending actuator with feedback from a 3D printed strain sensor. This process utilizes the Finite Element Method (FEM) to design a bellow type pneumatic bending actuator that can handle pressures up to 4 bar. The developed actuator is produced with a Fused Deposition Modeling (FDM) 3D printer method with the elastic filament NinjaFlex. Soft sensors are 3D printed with the conductive filament Eel and their strain-resistive performance in hysteresis, linearity, and repeatability are investigated by testing 3D printed sensors with different shapes. The optimal sensor design is then selected and applied onto the soft actuator and the resistance signal from the sensor is used as the shape feedback signal for the soft actuator. Two different controllers are applied for the shape control of the soft actuator using the feedback from the sensor and the controller performance is compared experimentally. A gripper composed of three closed-loop controlled soft actuators is developed to perform complex grasping tasks. / Denna avhandling konstruerar ett 3D-skrivet mjukt ställdon som återkopplas med en 3D-skriven böjsensor. Arbetet använder Finita Elementmetoden (FEM) för att skapa ett böjande bälgställdon som klarar av 4 bar av lufttryck. Det framtagna ställdonet är tillverkad av det elastiska filamentet NinjaFlex med 3D-skrivarmetoden Smält Deponeringsmodellering (FDM). Dem mjuka sensorerna är 3D-skrivna med det elektriskt ledande filamentet Eel. Sensorernas ansträgning-resistiva prestanda med avseende på hysteres, linjäritet, och repeterbarhet är undersökta genom att utföra experiment med olika former. Den optimala sensorformen är sedan applicerad på det mjuka ställdonet och dess resistiva signal från sensorn används för återkoppling av det mjuka ställdonets böjning. Med den applicerade sensorn utvärderas två olika kontrollmetoder för att kontrollera böjningen av det mjuka ställdonet, kontrollmetodernas prestanda jämförs sedan experimentellt. Ett gripdon som består av tre återkopplade, mjukaställdon är sedan konstruerad för att utföra komplexa grepp.

Man’s desire to replicate/mimic the nature’s creation provided an impetus and inspiration to the rapid advancements and progress made in the sensors and actuators technology. A normal human being has five basic sensory organs, which helps and guides him in performing the routine tasks. This underlines the importance of basic sensory organs in a human life. In a similar fashion, sensors and actuators are of paramount importance for most of the science and engineering applications. The aim of the present thesis work is to explore the application of piezoelectric ZnO thin films deposited on a flexible substrate for the development of sensors and actuators. Detailed study was performed on the suitability of three different flexible substrates namely Phynox, Kapton and Mylar. However, Phynox alloy substrate was found to be a suitable substrate material for the above mentioned applications. Sputtering technique was chosen for the deposition of ZnO thin films on to Phynox substrate. The necessary process parameters were optimized to achieve good quality piezoelectric thin films. In the present work, sensors have been developed by utilizing the direct piezoelectric effect of ZnO thin films deposited on Phynox alloy substrate. These includes a flow sensor for gas flow rate measurement, impact sensor for non-destructive material discrimination study and a Thin Film Sensor Array (TFSA) for monitoring the impact events. On the other hand, using the converse piezoelectric effect of ZnO thin films, actuators have also been developed. These include a thin film micro actuator and a Thin Film Micro Vibrator (TFMV) for vibration testing of micro devices. The thesis is divided into following seven chapters. Chapter 1: This chapter gives a general introduction about sensors and actuators, piezoelectric thin films, flexible substrates, thin film deposition processes and characterization techniques. A brief literature survey of different applications of piezoelectric thin films deposited on various flexible substrates in device development is presented. Chapter 2: A novel flexible metal alloy (Phynox) and its properties along with its applications are discussed in this chapter. ZnO thin films were deposited on Phynox substrate by Rf reactive magnetron sputtering technique. The sputtering process parameters such as: Ar:O2 gas ratio, substrate temperature and RF power were optimized for the deposition of good quality piezoelectric ZnO thin films. The deposited ZnO thin films were characterized using XRD, SEM, AFM and d31 coefficient measurement techniques. Chapter 3: It reports on the comparative study of properties of piezoelectric ZnO thin films deposited on three different types of flexible substrates. The substrate materials employed were a metal alloy (Phynox), polyimide (Kapton), and polyester (Mylar). Piezoelectric ZnO thin films deposited on these flexible substrates were characterized by XRD, SEM, AFM and d31 coefficient measurement techniques. A vibration sensing test was also performed for the confirmation of good piezoelectric property. Compared to the polymer flexible substrates, the metal alloy flexible substrate (Phynox) was found to be more suitable for integrating ZnO thin film for sensing applications. Chapter 4: The development of a novel gas flow sensor for the flow rate measurement in the range of L min-1 is presented in this chapter. The sensing element is a Phynox alloy cantilever integrated with piezoelectric ZnO thin film. A detailed theoretical analysis of the experimental set–up showing the relationship between output voltage generated and force at a particular flow rate has been discussed. The flow sensor is calibrated using an in-house developed testing set-up. Chapter 5: This chapter is divided into two sections. Section 5.1 reports on the development of a novel packaged piezoelectric thin film impact sensor and its application in non-destructive material discrimination studies. Different materials (Iron, Glass, Wood and Plastic) were successfully discriminated by using the developed impact sensor. The output response of impact sensor showed good linearity and repeatability. The impact sensor is sensitive, reliable and cost-effective. Section 5.2 reports on the development of a Thin Film Senor Array (TFSA) for monitoring the location and magnitude of the impact force. The fabricated TFSA consists of evenly distributed ZnO thin film sensor array. Chapter 6: It consists of two sections. Section 6.1 reports on the fabrication of micro actuator using piezoelectric ZnO thin film integrated with flexible Phynox substrate. A suitable concave Perspex mounting was designed for the actuator element. The actuator element was excited at different frequencies for the supply voltages of 2V, 5V and 8V. The developed micro actuator has the potential to be used as a micro pump for pumping nano liters to micro liters of fluids. Section 6.2 reports the design and development of a portable ready to use Thin Film Micro Vibrator (TFMV). The TFMV is capable of providing the vibration amplitude in the range of nanometer to micrometer. A thin silicon diaphragm was used as a test specimen for its vibration testing studies using the developed TFMV. The TFMV is light-weight and have internal battery, hence no external power supply is required for its functioning. Chapter 7: The first section summarizes the salient features of the work presented in this thesis. In the second section the scope for carrying out the further work is given.

L’application de cette thèse est le contrôle actif de la combustion dans les brûleurs industriels à combustible liquide. Il s’agit d’explorer les possibilités de contrôle d’un spray par des jets gazeux auxiliaires. Deux familles d’actionneurs utilisant ce procédé ont été testées sur un atomiseur coaxial assisté par air. Le premier dispositif est appelé (Dev). Composé d’un unique jet actionneur, il vise à dévier le spray. La seconde configuration, appelée (Sw), est équipée de 4 jets auxiliaires tangents au spray afin de lui conférer un effet de swirl et d’en augmenter le taux d’expansion. Les mesures de granulométrie par PDA et les visualisations du spray par strioscopie démontrent un effet important du contrôle sur l’atomisation et la forme du spray. On observe en outre une déviation pouvant atteindre 30°avec l’actionneur (Dev) et une augmentation du taux d’expansion de 80% dans le cas (Sw). Des simulations du banc expérimental ont de plus été menées avec le code AVBP. L’écoulement de gaz est calculé par simulation aux grandes échelles (SGE ou LES en Anglais). L’approche lagrangienne est utilisée pour simuler la phase dispersée. Une attention particulière a été portée aux conditions d’injection du gaz et des gouttes dans le calcul. Ceci a abouti au développement d’une nouvelle condition limite caractéristique non réfléchissante (VFCBC) destinée à l’injection d’écoulements turbulents en LES compressible. Les résultats de LES présentent un bon accord avec les mesures expérimentales. Les effets du contrôle sur la dynamique des gouttes et sur la topologie du spray (forme, déviation, expansion) sont correctement décrits. / The present work focuses on active control of two-phase combustion in industrial burners. The generic method explored in this thesis consists in controlling the injected fuel spray with transverse air jets. Two families of these jet actuators are tested on a coaxial airblast atomizer. The first system (Dev) is used to modify the trajectory of the spray, while the second one (Sw) introduces swirl into the spray to modify its spreading rate and mixing with the surrounding air. Experimental characterisations of the controlled flow with Schlieren visualisations and Phase Doppler Anemometry (PDA) show that actuators induce important effect on the spray. The deviation angle reaches 30° for the actuator (Dev) and the expansion rate increases of 80 % in the swirl case (Sw). Simulations of the experiment are then performed with the CFD code AVBP. The gas flow is computed with Large Eddy Simulation (LES). A Lagrangian formulation is used to simulate droplets trajectories. A particular attention is given to the injection of the gas flow and the droplets in the calculations. Therefore, a new non-reflecting characteristic boundary condition (VFCBC) has been derived to inject turbulent flows in compressible LES. A good agreement is observed between simulation and experiment. Control effects on the spray topology ( features, deviation, spread rate) and on the droplets velocities and diameters are correctly described by the Lagrangian LES.

Le sujet de cette thèse s'inscrit dans le cadre des systèmes tolérants aux défauts sous contraintes avec prise en considération de la dégradation des performances. L'objectif principal de ce travail consiste à considérer la gestion des références comme une partie intégrante du système de commande tolérant aux défauts. Dans la littérature, la plupart des méthodes actives de tolérance aux défauts supposent que le recouvrement du système nominal est toujours possible et que les performances nominales sont toujours atteignables. Cette condition est peu réaliste dans la pratique puisque plusieurs éléments empêchent le système reconfiguré de revenir à son mode de fonctionnement nominal. Dans le domaine industriel, l'ensemble des contraintes du système est un handicap majeur qui limite le fonctionnement nominal d'un système à des plages fonctionnelles bien définies. Ces plages fonctionnelles sont énormément réduites après l'apparition de certains défauts dits sévères et qui affectent généralement les actionneurs. Par conséquent, cette hypothèse de recouvrement des performances nominales dans le cas des systèmes sous contraintes limite l'ensemble des défauts traités par ces méthodes classiques à quelques défauts dits mineurs. Afin de remédier a ce problème, une architecture de reconfiguration structurée en deux niveaux est proposée. Le premier concerne les algorithmes classiques de reconfiguration en agissant sur un contrôleur reconfigurable, et le deuxième agit sur le module de gestion des références conçu à base d'un gouverneur de référence avec offset. La connaissance exacte du modèle en post-défaut nécessite un système de détection et diagnostic de défaut qui permet d'estimer l'amplitude de défaut, ce qui conduit à la synthèse d'un observateur adaptatif d'estimation de défaut à base de LMI. Afin de synchroniser le déroulement du processus FTC, deux indices ont été conçus. Le premier indice porte sur le mécanisme de décision permettant de sélectionner le/les niveau(x) de reconfiguration nécessaire(s) à l'accommodation du défaut. Le deuxième indice permet d'évaluer le niveau de dégradation du système « post-défaut ». Une dégradation de performance est toujours admise tant que les consignes de sécurité sont respectées / The subject of this thesis is part of fault tolerant control systems under constraints with consideration of performance degradation. The main objective of this work is to consider the reference management as an integral part of the fault tolerant control system. In the literature, the most active methods of fault tolerance imply that recovery of the nominal system is always possible and that performance ratings are still achievable. This requirement is unrealistic in practice because several factors prevent the system reconfigured back to its nominal operating mode. In industry, the set of system constraints is a major problem which limits the nominal operating of the system to defined functional ranges. These functional ranges are reduced dramatically after the occurrence of some faults known as severe faults that generally affect the capacity of actuators. Therefore, this assumption of nominal performance recovery in the case of systems under constraints limits the set of faults treated with these conventional methods to a few minor faults. To remedy this problem, architecture of reconfiguration structured in two levels is proposed. The first level concerns the conventional reconfiguration algorithms acting on a reconfigurable controller, and the second acts on the module of reference management based on a reference-offset governor. The exact knowledge of the post-fault model requires a fault detection and diagnosis system to estimate the magnitude of fault, which led to the synthesis of an adaptive observer based LMI for estimating fault. To synchronize the FTC process flow, two indices have been designed. The first index refers to the decision mechanism for selecting the reconfiguration level required for the accommodation of the fault. The second index used to evaluate the level of the degradation of the system "post-fault". The performance degradation is still allowed as long as safety instructions are respected

Microdispositivos piezelétricos tem uma vasta aplicação em mecânica de precisão, como, por exemplo, manipulação de células, microcirurgias, equipamentos de nanotecnologia e principalmente em microeletromecanismos (MEMS). Os microdispositivos piezelétricos considerados nesta tese essencialmente consistem de uma estrutura multi-flexível atuada por duas ou mais piezocerâmicas, que geram deslocamentos e forças em direções e regiões pré-determinadas do domínio, ou seja, a estrutura multi-flexível atua como um transformador mecânico amplificando e alterando os deslocamentos gerados pelas piezocerâmicas nos movimentos de atuação. O desenvolvimento destes microdispositivos piezelétricos em sua grande maioria não utiliza ferramentas sistemáticas e genéricas. A complexidade dos movimentos de atuação torna o desenvolvimento dos microdispositivos piezelétricos complexo, principalmente devido ao surgimento de movimentos indesejados ou acoplados durante a sua atuação. Portanto, é necessário um método sistemático e eficiente como o método de otimização topológica (MOT), que incorpore na sua formulação as principais exigências de projeto dos microdispositivos, como apresentado nesse trabalho. O MOT implementado é baseado na abordagem CAMD (Distribuição Contínua da Distribuição de Material), onde as pseudo-densidades são interpoladas nos nós de cada elemento finito, resultando numa distribuição contínua de material no domínio. Um método adjunto foi implementado para o cálculo das sensibilidades. São consideradas três formulações. A primeira denominada de MAPs (Multi-Atuadores Piezelétricos) considera as regiões piezocerâmicas fixas, otimizando apenas a estrutura multi-flexível no domínio de projeto. Nesta formulação materiais não-piezelétricos (como, por exemplo, Alumínio) e vazio são distribuídos no domínio de projeto, mantendo as regiões piezocerâmicas fixas e homogêneas. Para validar os resultados obtidos com essa formulação foram fabricados protótipos de nanoposicionadores $XY$, que foram caracterizados experimentalmente utilizando técnicas de interferometria laser, considerando excitação quasi-estática. No entanto, essa primeira formulação impõe restrições no problema, limitando a optimalidade da solução obtida pela otimização topológica. Assim, surgiu a necessidade de desenvolver uma segunda formulação, que permite distribuir simultaneamente material não-piezelétrico, piezelétrico e vazio no domínio de projeto, denominada de LOMPs (Localização Ótima do Material Piezelétrico). A formulação dos LOMPs obtém simultaneamente a localização do material piezelétrico na estrutura flexível otimizada pela OT, e inclui também uma variável de projeto para determinar o ângulo ótimo entre as direções de polarização e do campo elétrico. Nesta formulação como as posições dos eletrodos não são conhecidas, ``a priori\'\', é utilizado como abordagem aplicar um campo elétrico constante para determinar a localização do material piezelétrico e conseqüentemente dos eletrodos. Finalmente, foi explorado o conceito de materiais com gradação funcional (MGFs) no projeto dos MAPs. Os MGFs apresentam uma distribuição contínua de materiais na sua microestrutura, não possuindo interface entre os materiais distribuídos, o que possibilita aumentar a vida útil do dispositivo piezelétrico. Assim, foi implementado uma terceira formulação denominada de MAPs MGFs, que permite obter a gradação ótima de materiais piezelétricos e não-piezelétricos no domínio piezocerâmico dos MAPs, conjuntamente com a topologia da estrutura multi-flexível. Essa formulação foi estendida para projetar atuadores bilaminares MGFs. Todas as formulações desenvolvidas utilizam uma função multi-objetivo, que permite controlar a rigidez e a flexibilidade minimizando o movimento acoplado, de cada movimento de atuação. Os exemplos numéricos são limitados a modelos bi-dimensionais, utilizando o estado plano de tensões e deformações mecânicas e elétricas, uma vez que a grande maioria das aplicações dos microdispositivos piezelétricos são bi-dimensionais. / Microtools offer significant promise in a wide range of applications such as cell manipulation, microsurgery, nanotechnology processes, and many other fields. The microtools considered in this doctoral thesis essentially consist of a multi-flexible structure actuated by two or more piezoceramic devices that when each piezoceramic is actuated, it generates an output displacement and force at a specified point of the domain and direction. The multi-flexible structure acts as a mechanical transformer by amplifying and changing the direction of the piezoceramic output displacements. Thus, the development of microtools requires the design of actuated flexible structures that can perform complex movements. The development of these microtools is still in the beginning and it can be strongly enhanced by using design tools. In addition, when multiple piezoceramic devices are involved, coupling effects in their movements become critical, especially the appearance of undesired movements, which makes the design task very complex. One way to avoid such undesirable effects is the use of a systematic design method, such as topology optimization, with appropriate formulation of the optimization problem. The topology optimization method implemented is based on the CAMD (Continuous Approximation of Material Distribution) approach where fictitious densities are interpolated at each finite element, providing a continuum material distribution in the domain. The corresponding sensitivity analysis is presented using the adjoint method. Three formulations are considered. The first formulation, called Piezoelectric Multi-Actuators (PMAs), keeps fixed piezoceramic positions in the design domain and only the flexible structure is designed by distributing some non-piezoelectric material (Aluminum, for example). $XY$ Piezoelectric Nanopositioner are manufactured and experimentally analyzed to validate the results of the topology optimization obtained using this formulation. Experimental analyses are conducted using laser interferometry to measure displacement, while considering a quasi-static excitation. However, this first formulation imposes a constraint to the position of piezoelectric material in the optimization problem limiting the optimality of the solution. Thus, the second formulation presented, called LOMPs, allows the simultaneous distribution of non-piezoelectric and piezoelectric material in the design domain, to achieve certain specified actuation movements. The optimization problem is posed as the simultaneous search for an optimal topology of a flexible structure as well as the optimal position of piezoceramics in the design domain and optimal rotation angle of piezoceramic material axes that maximize output displacements or output forces at a specified point of the domain and direction. When the distribution of a non-piezoelectric conductor material and a piezoceramic material is considered in the design domain, the electrode positions are not known ``a priori\'\'. To circumvent this problem, an electric field is applied as electrical excitation. Finally, the concept of functionally graded materials (FGM) is applied to PMAs design. FGMs are special materials that possess continuously graded properties without interfaces which can increase lifetime of piezoelectric devices. Thus, a third formulation is implemented to find the optimum gradation and polarization sign variation of piezoceramic FGMs, while simultaneously optimizing the multi-flexible structural configuration. This formulation is extended to design bimorph type FGM actuators. For all developed formulations, a multi-objective function is defined that controls the stiffness and flexibility, minimizing the coupling movement of each actuated movement. The present examples are limited to two-dimensional models because most part of the applications for such micro-tools are planar devices.

Este trabalho apresenta o desenvolvimento de um método para garantir a proteção dos dados contra falhas de comunicação, em redes de sensores inteligentes sem fios. A rede sem fios foi empregada nos ensaios de modelos físicos reduzidos em centrífuga para estudar o comportamento das âncoras \"tartaruga\", utilizadas nas linhas de ancoragem de sistemas oceânicos para produção de óleo e gás em águas profundas. O emprego da tecnologia de redes de sensores sem fios tem aumentado em muitas áreas da sociedade, principalmente na engenharia. Dessa forma, muitos problemas estão sendo enfrentados e estudados pelos pesquisadores. Sobretudo no que diz respeito à interferência ambiental, relação de potência e alcance, integridade da informação, miniaturização dos dispositivos, autonomia de energia, limitação de algoritmos e vida útil. A inserção da tecnologia de redes de sensores inteligentes sem fios nos ensaios de modelos físicos reduzidos em centrífuga, além de ser inédita no Brasil, permitirá avanços significativos na determinação de parâmetros que, atualmente, são de difícil obtenção com tecnologias convencionais como os sistemas de aquisição de dados e controle que utilizam cabos e fios. Muitas vezes depara-se com a inconveniência do peso dos cabos e dificuldades de instalação dos dispositivos nos modelos, pela sua pouca portabilidade. / This work present a method development to guarantee of the integrity data in the wireless smart sensor networks, employed in centrifuge physical modeling tests of anchors used as fixing devices of deep water production oil and gas systems. The use of wireless smart sensor networks technology has been increasing in many engineering areas. In spite of this evidence, lots of problems are being faced and studied by the researchers, environmental interference, power and reach relations, integrity of the information, miniaturization of the devices, energy autonomy, algorithms and useful life. The use of the wireless smart sensor networks technology in the reduced physical models test in centrifuge, by first time in Brazil, will allow significant advances in the parameters determination. The conventional instrumentation presents inconvenience of the weight cables and difficulties of the devices in the models by limited portability.

Doctor of Philosophy (PhD) / With improvements in actuation technology and sensory systems, it is becoming increasingly feasible to create powered exoskeletal garments that can assist with the movement of human limbs. This class of robotics referred to as human-machine interfaces will one day be used for the rehabilitation of paralysed, damaged or weak upper and lower extremities. The focus of this project was the development of an exoskeletal interface for the rehabilitation of the hands. A novel sensor was designed for use in such a device. The sensor uses simple optical mechanisms centred on a spring to measure force and position simultaneously. In addition, the sensor introduces an elastic element between the actuator and its corresponding hand joint. This will allow series elastic actuation (SEA) to improve control and safely of the system. The Hand Rehabilitation Device requires multiple actuators. To stay within volume and weight constraints, it is therefore imperative to reduce the size, mass and efficiency of each actuator without losing power. A method was devised that allows small efficient actuating subunits to work together and produce a combined collective output. This work summation method was successfully implemented with Shape Memory Alloy (SMA) based actuators. The actuation, sensory, control system and human-machine interface concepts proposed were evaluated together using a single-joint electromechanical harness. This experimental setup was used with volunteer subjects to assess the potentials of a full-hand device to be used for therapy, assessment and function of the hand. The Rehabilitation Glove aims to bring significant new benefits for improving hand function, an important aspect of human independence. Furthermore, the developments in this project may one day be used for other parts of the body helping bring human-machine interface technology into the fields of rehabilitation and therapy.

The interaction of a shock wave with a boundary layer is a classic viscous/inviscid interaction problem that occurs over a wide range of high speed aerodynamic flows. For example, on transonic wings, in supersonic air intakes, in propelling nozzles at offdesign conditions and on deflected controls at supersonic/transonic speeds, to name a few. The transonic interaction takes place at Mach numbers typically between 1.1 and 1.5. On an aerofoil, its existence can cause problems that range from a mild increase in section drag to flow separation and buffeting. In the absence of separation the drag increase is predominantly due to wave drag, caused by a rise in entropy through the interaction. The control of the turbulent interaction as applied to a transonic aerofoil is addressed in this thesis. However, the work can equally be applied to the control of interaction for numerous other occurrences where a shock meets a turbulent boundary layer. It is assumed that, for both swept normal shock and unswept normal shock interactions, as long as the Mach number normal to the shock is the same, then the interaction, and therefore its control, should be the same. Numerous schemes have been suggested to control such interaction. However, they have generally been marred by the drag reduction obtained being negated by the additional drag due to the power requirements, for example the pumping power in the case of mass transfer and the drag of the devices in the case of vortex generators. A system of piezoelectrically controlled flaps is presented for the control of the interaction. The flaps would aeroelastically deflect due to the pressure difference created by the pressure rise across the shock and by piezoelectrically induced strains. The amount of deflection, and hence the mass flow through the plenum chamber, would control the interaction. It is proposed that the flaps will delay separation of the boundary layer whilst reducing wave drag and overcome the disadvantages of previous control methods. Active control can be utilised to optimise the effects of the boundary layer shock wave interaction as it would allow the ability to control the position of the control region around the original shock position, mass transfer rate and distribution. A number of design options were considered for the integration of the piezoelectric ceramic into the flap structure. These included the use of unimorphs, bimorphs and polymorphs, with the latter capable of being directly employed as the flap. Unimorphs, with an aluminium substrate, produce less deflection than bimorphs and multimorphs. However, they can withstand and overcome the pressure loads associated with SBLI control. For the current experiments, it was found that near optimal control of the swept and unswept shock wave boundary layer interactions was attained with flap deflections between 1mm and 3mm. However, to obtain the deflection required for optimal performance in a full scale situation, a more powerful piezoelectric actuator material is required than currently available. A theoretical model is developed to predict the effect of unimorph flap deflection on the displacement thickness growth angles, the leading shock angle and the triple point height. It is shown that optimal deflection for SBLI control is a trade-off between reducing the total pressure losses, which is implied with increasing the triple point height, and minimising the frictional losses.