La présence de bactéries et biofilms est une préoccupation permanente dans de nombreux domaines. Ils sont à l’origine de nombreux faits d’actualité qui ont un coût important pour le système de santé. L’objectif de notre travail visait à élaborer des films nanocomposite transparents contenant des particules métalliques nanométriques d'élément antibactérien (Ag ou Cu) immergées dans une matrice d’oxyde (TiO₂). La méthode de dépôt DLI-MOCVD (Direct Liquid Injection-Metal Organic Chemical Vapor Deposition) a été employée pour élaborer les films composites. Ce procédé permet le contrôle de la fraction molaire des précurseurs injectés dans le réacteur CVD et de revêtir des supports 3D (poreux). La croissance et la structure du dioxyde de titane (TiO₂) sont influencées par la présence du précurseur contenant l’élément antibactérien. La fraction molaire du précurseur (Ag ou Cu) modifie les caractéristiques physico chimiques et structurales des dépôts. L'activité antibactérienne est mesurée selon la norme JIS Z 2801:2000 avec S. aureus et E. coli en l’absence de lumière. Des essais antibactériens spécifiques ont été optimisés afin d'évaluer leur activité proche de condition réelle. La composition des dépôts influence fortement l’activité antibactérienne d’inactif à bactéricide. Des corrélations entre la microstructure et la composition des films et leurs propriétés antibactériennes sont discutées. / The presence of bacteria and biofilms is permanent concern in many fields. Their presences are at the origin of many events which have high costs for the health system. In this objective, this work aimed to elaborate transparent nanocomposite thin films which are composed of nanometric metallic particles of antibacterial element (Ag or Cu) embedded in an oxide matrix (TiO₂). The DLI-MOCVD process (Direct Liquid Injection-Metal Organic Chemical Vapour Deposition) was used to elaborate these thin films. This process allows the quantity of precursors injected into the CVD reactor to be controlled and porous body to be coated. The growth mechanisms and the structure of the Titanium dioxide (TiO₂) are influenced by the presence of the organic precursor which contains the antibacterial element. The mole fraction of precursor (Ag or Cu) modifies the physico-chemical and structural properties of films. The antibacterial activity was tested according to the standard JIS Z 2801: 2000 with S. aureus and E. coli without light Specific tests were optimised in order to evaluate their activity in environments more representative. The composition of coatings impacts strongly the antibacterial activities from inactive to bactericidal properties. Correlations between the microstructure and composition of films and their antibacterial properties are discussed.

Ce travail porte sur le développement de protocoles de croissance par CVD à injection directe de liquide (DLI-CVD) de films catalytiques poreux potentiellement utilisables dans les piles à combustible de type PEMFC. Les objectifs étaient de contrôler et de réduire au maximum la charge en platine, d’obtenir des matériaux à grande surface spécifique, c'est-à-dire très poreux, mais aussi d’utiliser des précurseurs à bas coût.Dans un premier temps, le platine a été promu par de l’oxyde de cérium, matériau qui possède lui-même des propriétés catalytiques. L’optimisation des paramètres de croissance a montré le rôle majeur de la température de dépôt mais aussi du flux des précurseurs sur la morphologie finale des films. Un dopage contrôlé en platine de la surface de l’oxyde de cérium a ainsi pu être mis au point à partir du dépôt simultané de cérine et de platine. Le flux de précurseur du platine a alors permis d’ajuster la charge et l’état d’oxydation de cet élément au sein des films sans pour autant modifier leur porosité. Il est, par exemple, possible d’élaborer des films minces d’oxyde de cérium composés de particules nanométriques dopées en extrême surface avec 5 % de platine à l’état +II. L’effet du flux de précurseur sur l’état d’oxydation du platine a été confirmé pour le système Pt/TiO2. Dans un second temps, des oxycarbures de tungstène ont été synthétisés de façon à éliminer totalement le platine du catalyseur. Un procédé en deux étapes a été mis au point permettant d’obtenir des dépôts d’oxycarbure de tungstène possédant de grandes surfaces spécifiques en déposant un film utra-mince et conforme d’oxycarbure sur une couche poreuse d’oxyde de tungstène. / This work is focused on development of growth protocols by direct liquid injection chemical vapor deposition (DLI-CVD) of catalytic porous films which could be used in proton exchange membrane fuel cells (PEMFC). The aim of this work was to reduce or even proscribe platinum in catalysts having large specific surface area i.e. being very porous. Besides, the aim is also to use mainly low cost precursors.Cerium oxide, which is a material widely used as catalyst, has been chosen to partially substitute platinum. Porous CeO2 layers were obtained by the optimization of processing parameters such as deposition temperature or precursors flow rates. Controlled platinum doping of cerium oxide surface has been obtained from deposition of ceria and platinum at the same time. The platinum precursor flow rate has allowed adjusting the load and the oxidation state of Pt in films without changing their porosity. For example, it was possible to synthesize thin cerium oxide films composed of surface Pt doped nanoparticles. In such a case, the Pt content is 5% in top most layers and its oxidation state is +II. The effect of precursor flow rate on the platinum oxidation state was confirmed from the study of the Pt / TiO2 system. Finally, platinum has been fully replaced by tungsten oxycarbide. A two steps process has been developed to obtain porous oxycarbide layers by depositing a conformed tungsten oxycarbide ultra-thin film on a porous tungsten oxide layer.

The greenhouse industry is interested in light emitting diodes (LEDs) as a light source supplement to solar light to improve plant growth and development. Before LEDs can be adopted as supplemental light for greenhouse crops, plant responses to LED spectral quality need to be investigated. Tomato and cucumber seedlings were grown under different supplemental blue and red photon flux ratios (B:R ratios) under high (16-19 mol m⁻² d⁻¹) and low (5-9 mol m⁻² d⁻¹) solar daily light integrals (DLIs). The supplemental daily light integral was 3.6 mol m⁻² d⁻¹. A treatment without supplemental light served as a control. Both tomato and cucumber seedlings had increased growth rate and improved morphology when grown under the supplemental LED light compared to the control. However, no significant differences were observed for any growth and morphological parameters measured in this study between the different B:R ratios for both cucumber and tomato transplants under high DLI conditions. Cucumber seedlings showed a tendency to decrease dry mass, leaf number and leaf area under low DLI conditions with increasing B:R ratio. Tomato seedlings did not show any differences between the different B:R ratios under low DLI conditions. Seedlings growth and morphology under supplemental LED light were compared to those under supplemental high pressure sodium (HPS) light. Cucumber seedlings under supplemental HPS light had greater shoot dry mass than those under the supplemental red LED light. Tomato shoot dry mass showed no differences between the HPS and red LED supplemental light treatments. Cucumber seedlings were also grown under supplemental LED pulsed lighting and supplemental LED continuous lighting. Cucumber seedlings showed no differences in shoot dry mass and net photosynthetic rate between the treatments. Collectively, these studies concluded that red LED is preferred for supplemental lighting and the increase of blue light does not offer any benefits unless the efficiency of blue LEDs largely exceeds the red LEDs. The results of this research can be used for fixture development by LED manufactures and as a decision making tool for the adoption of supplemental LED lighting by greenhouse growers.

No description available.

Des procédés atmosphériques de dépôt chimique en phase vapeur assisté par l'injection directe liquide (DLI-CVD), prometteurs pour traiter des pièces métalliques au défilé, ont permis l'élaboration à basse température de revêtements métallurgiques performants. Deux précurseurs organométalliques de chrome ont été employés dans différentes atmosphères : Cr (CO)6 pour des dépôts issus du système chimique Cr-O-N-C, et le bisbenzènechrome pour des monocouches de chrome métallique, de carbure (Cr-C) et de nitrure de chrome (CrN), ainsi que des multicouches CrN/Cr-C de bipériode 25 nm. Une approche thermodynamique a permis le calcul d'un nouveau diagramme ternaire Cr-N-C à 527°C, et l'étude de l'impact du solvant sur la nature et la qualité des dépôts en comparaison avec les systèmes chimiques sans solvant. Les propriétés des revêtements (dureté, adhérence, usure, corrosion) sont discutées en relation avec leur microstructure. Les revêtements multicouches nanostructurés CrN/Cr-C présentent des duretés et une tenue à l'usure prometteuses.

This paper deals with the problem of two-stroke engine pre-ignition controller with the use of microcontroller for single-cylinder engine and double-cylinder engine. The mechanical design is drawn for motorcycles JAWA and ČZ and for engines of the same mechanical type. The establishment uses non-contact status analysis of engine with non-electric sensor. The very important thing for the design is the simplicity of the establishment. The other important thing is the minimisation of mechanical arrangement of engine and the vehicle as a whole. The importance of this establishment is non-contact switching and the possibility of changing pre-ignition maps depending on the number of rotations per minute, the temperature and the load of the engine.

Students from dual language immersion (DLI) classrooms are required to learn the language through content. However, some students have not yet developed these abilities by the time they start fourth grade. Thus, to fully comprehend content such as science, students need stronger reading and writing abilities in the second language (L2). To help stakeholders have a better understanding on how to effectively help students throughout this process, this action research studied the effectiveness of integrating literacy with science and mobile assisted language learning (MALL). Findings showed that the integrations of literacy, science and MALL were effective with statistically significant results in science and reading. These findings also yielded pedagogical implications about the importance of considering students' language background and gender, as well as the use of MALL when teaching and planning the curriculum for DLI classrooms.

No description available.

Approved for public release, distribution is unlimited / This thesis analyzes factors related to academic, military and personal backgrounds that affect graduation of students enrolled at the Defense Language Institute Foreign Language Center (DLIFLC). The data in this thesis were taken from DLIFLC and only students from the four principal services with valid DLAB scores were considered for this study. Also, as DLI is concerned with students who do not make the grade academically, entries having administrative attritions were not considered. Four logistic regression models were analyzed for the purposes of this study: Graduation of students across all four categories of languages taught at DLIFLC, graduation of students in Category I languages, graduation of students in Category III languages and graduation of students in Category IV languages. The results of this study can assist DLIFLC in investing its resources in students with the best chances of success and assist the staff in identifying the weaker students from the onset of the course. / Major, Republic of Singapore Air Force

This master's thesis is oriented on software development processes improvement techniques. It presents modern approaches of process development and analyses problems of their management and usage in various life cycle phases. In connection with these techniques it brings draft of support tool, which increases automatization of processes development with pertinent cooperation with other tools, as one of presumptions of improvement of their quality.