This thesis studies the electric aspects of a linear synchronous permanent magnet generator. The generator is designed for use in a wave energy converter, which determines the fundamental requirements of the generator. The electromagnetic properties of the generator are investigated with a finite element based simulation tool. These simulations formed the base of the design and construction of a laboratory prototype. Several experiments where conducted on the prototype generator. The results verify at large the simulation tool. However, a difference between the measured and simulated air gap flux was discovered. This was attributed to the longitudinal ends of the generator, which are ignored in the simulation tool. Experiences from the construction, and further finite element studies, led to a significant change in the support structure of the first offshore prototype generator. A complete wave energy converter was constructed and launched, the 13th of March, on the west coast of Sweden. A study of the load resistance impact on the power absorption has been carried out. An optimal load interval, with regard to power absorption, has been identified. Furthermore, the generator has proofed to withstand short term overload several times larger than the nominal load. Finally, the longitudinal ends’ influence on the flux distribution was investigated with an analytical model, as well as finite element simulations. A possible problem with large induction of eddy currents in the actuator back steel was identified. This work is a part of a larger project, which aims do develop a viable wave energy conversion system.

As the interest in intentional electromagnetic interference (IEMI) increases, so does the need of a suitable antenna which endures those demanding conditions. The ultrawideband (UWB) technology provides an elegant way of generating high-voltage UWB pulses which can be used for IEMI. One UWB antenna, invented solely for the purpose of radiating pulses, is the impulse radiating antenna (IRA). In the course of this master thesis work, a suitable geometry of the IRA is suggested, and modelled, for the high-voltage application of 90 kV.

The objective of this thesis was to improve a paraffin actuated micropump design, to be able to pump against extreme pressures (above 100 bar). This was accomplished by initially studying the membrane activation, using video capturing. The micropump has been improved to withstand pressures high enough, to enable use in an high-performance liquid chromatography (HPLC) system. The micropump has been shown to pump against back pressures up to 150 bar, with a positive net-flow. This should be compared with the previously recorded maximum back pressure of 50 bar. The pumping against high back pressures was possible due to an increased understanding of the sealing of the membranes. This resulted in a new design that was manufactured and characterised. Without clamping the pump was measured to manage back pressures of 10 bar, and then starting to leak in a bond at the flow channel. With supporting clamping, the managed back pressures increased ten folded. When measured on the different valves, pressure above 200 bar has been possible to withhold. Although the valves were below their maximum limit, the pressure was not possible to be further increased due to a limitation in the equipment, i.e. risk of damaging the connections. When examined after pressurised at extreme pressures (above 100 bar) several times, no signs of fatigue or damage of the membrane was seen. A new behaviour of the valves was discovered. Above certain pressures some designs self sealed, i.e. withholding the pressure after the voltage was turned off. For these valves the pressure had to be released by some other means.

The main ambition of this degree project is to illustrate the fundamental problems of today’s electric tariff regulation and the usage of the analyzing tool; The Network Tariff Model. There is a further discussion of potential problems and clear improvements of the 2012 years proposed network tariff regulation. Interviews have been conducted with specific network companies and Energimarknadsinspektionen. The proposed regulation of 2012 is discussed from the government’s proposition. This paper clearly shows that the authority´s work has been conducted in a very unprofessional manner during the period of The Network Tariff Model. Transparency has been missing at the same time when quality control has been almost nonexistent from the authority. The regulation itself and the usage of The Network Tariff Model generated substantial criticism. Disagreement about the model was mostly about the use of methods and parameter settings. The new regulation of beforehand assessment of network tariffs is scheduled to be commissioned during 2012. This regulation has certain advantages compared to today’s for once because it counts for the actual costs for the corporations. At the same time this particular approach will demand a lot of resources of the authority. When the regulating models of the future are being developed legitimacy to all parties must be ensured. The regulations must at the same time be adjusted to the resources available for the grid authority. Likewise the process and nature of putting forward new regulations should be based on continuity to greater extent.

The need for energy is growing in the world and the market of nuclear power is now once more expanding. Some issues of the current light-water reactors can be solved by the next generation of nuclear power, Generation IV, where sodium-cooled reactors are one of the candidates. Phénix was a French prototype sodium-cooled reactor, which is seen as a success. Although it did encounter an earlier unexperienced phenomenon, A.U.R.N., in which a negative reactivity transient followed by an oscillating behavior forced an automatic emergency shutdown of the reactor. This phenomenon lead to a lot of downtime of the reactor and is still unsolved. However, the most probable cause of the transients is radial movements of the core, referred to as core-flowering. This study has investigated the available documentation of the A.U.R.N. events. A simplified model of core-flowering was also created in order to simulate how radial expansion affects the reactivity of a sodium-cooled core. Serpent, which is a Monte-Carlo based simulation code, was chosen as calculation tool. Furthermore, a model of the Phénix core was successfully created and partly validated. The model of the core has a k_eff = 1.00298 and a neutron flux of (8.43+-0.02)!10^15 neutrons/cm^2 at normal state. The result obtained from the simulations shows that an expansion of the core radius decreases the reactivity. A linear approximation of the result gave the relation: change in k_eff/core extension = - 60 pcm/mm. This value corresponds remarkably well to the around - 60 pcm/mm that was obtained from the dedicated core-flowering experiments in Phénix made by the CEA. Core-flowering can recreate similar signals to those registered during the A.U.R.N. events, though the absence of trace of core movements in Phénix speaks against this. However, if core-flowering is the sought answer, it can be avoided by design. The equipment that registered the A.U.R.N. events have proved to be insensitive to noise. Though, the high amplitude of the transients and their rapidness have made some researcher believe that the events are a combination of interference in the equipment of Phénix and a mechanical phenomenon. Regardless, the origin of A.U.R.N. seems to be bound to some specific parameter of Phénix due to the fact that the transients only have occurred in this reactor. A safety analysis made by an expert committee, appointed by CEA, showed that the A.U.R.N. events are not a threat to the safety of Phénix. However, the origin of these negative transients has to be found before any construction of a commercial size sodium-cooled fast reactor can begin. Thus, further research is needed.

ITU - T and the Moving Picture Expert Group (MPEG) have jointly, under the name of Joint Video Team (JVT), developed a new video coding standard. The standard is called H.264 and is also known as Advanced Video Coding (AVC) or MPEG-4 part 10. Comparisons shows that H.264 greatly outperforms MPEG-2, currently used in DVD and digital TV. H.264 halves the bit rate with equal image quality. The great rate - distortion performance means nevertheless a high computational complexity. Especially on the encoder side. Handling of audio and video, e.g. compressing and filtering, is quite complex and requires high performance hardware and software. A video encoder consists of a number of modules that find the best coding parameters. For each macroblock several $modes$ are evaluated in order to achieve optimal coding. The reference implementation of H.264 uses a brute force search for this mode selection which is extremely computational constraining. In order to perform video encoding with satisfactory speed there is an obvious need for reducing the amount of modes that are evaluated. This thesis proposes an algorithm which reduces the number of modes and reference frames that are evaluated. The algorithm can be regulated in order to fulfill the demand on quality versus speed. Six times faster encoding can be obtained without loosing perceptual image quality. By allowing some quality degradation the encoding becomes up to 20 times faster.

<p>Spiral grain in trees causes trouble to the wood industry, since boards sawn from trees with large grain angle have severe problems with form stability. Measurements of the grain angle under bark enable the optimisation of the refining process. The main objective of this thesis is to study the potential in estimating the grain angle by using microwaves. To do this, electromagnetic modelling and sensitivity analysis are combined.</p><p>The dielectric properties of wood are different along and perpendicular to the wood fibres. This anisotropy is central for the estimation of the grain angle by means of microwaves. To estimate the grain angle, measurements are used together with electromagnetic modelling for the scattering from plane surfaces and cylinders. Measurement set-ups are proposed to determine the material parameters, such as the grain angle, for plane boards and cylindrical logs. For cylindrical logs both near-field and far-field measurements are investigated. In general, methods for determining material parameters exhibit large errors in the presence of noise. In this case, acceptable levels of these errors are achieved throug using few material parameters in the model: the grain angle and two dielectric parameters, characterising the electrical properties parallel and perpendicular to the fibres.</p><p>From the case with plane boards, it is concluded that it is possible to make use of the anisotropy of wood to estimate the grain angle from the reflected electromagnetic field. This property forms then the basis of the proposed methods for the estimation of the grain angle in cylindrical logs. For the proposed methods, a priori knowledge of the moisture content or temperature of the wood is not needed. Furthermore, since the anisotropy persist also for frozen wood, the method is valid for temperatures below zero degrees Celsius.</p><p>For the case with cylindrical logs, sensitivity analysis is applied to the near-field as well as the far-field methods, to analyse the parameter dependence with respect to the measurement model and the errors introduced by noise. In this sensitivity analysis, the Cram\'{e}r-Rao bound is used, giving the best possible variance for estimating the parameters. The levels of the error bounds are high, indicating a problematic estimation problem. However, the feasibility of accurate estimation will be improved through higher signal-to-noise ratios, repeated measurements, and better antenna gain. The sensitivity analysis is also useful as an analytical tool to understand the difficulties and remedies related to the method used for determining material parameters, as well as a practical aid in the design of a measurement set-up.</p><p>According to the thesis, grain angle estimation is possible with microwaves. The proposed methods are fast and suitable for further development for in-field use in the forest or in saw mills.</p> / <p>Träd med växtvridenhet orsakar problem i träindustrin eftersom brädor som sågats från träd med stor fibervinkel har problem med formstabiliteten och vrider sig då de torkas. Mätning av fibervinkeln under bark möjliggör optimering av förädlingsprocessen. I den här avhandlingen kombineras elektromagnetisk modellering och känslighetsanalys för att undersöka möjligheterna att bestämma fibervinkeln med mikrovågor.</p><p>De elektriska egenskaperna hos trä är olika längs med och vinkelrätt mot fibrerna. Den här anisotropin är utgångspunkten för att bestämma fibervinkeln med hjälp av mikrovågor. För att skatta fibervinkeln används mätningar tillsammans med elektromagnetisk modellering för spridningen från plana ytor och cylindrar. Mätuppställningar föreslås för problemet att skatta materialparametrar, såsom fibervinkeln, i plana brädor och cylindriska stockar. För cylindriska stockar undersöks både närfälts- och fjärrfältsmätningar. I allmänhet har metoder för skattning av materialparametrar stora fel då systemet innehåller brus. Här erhålls acceptabla fel genom att använda få materialparametrar i modelleringen. De materialparametrar som används är fibervinkeln och två dielektriska parametrar som karakteriserar de elektriska egenskaperna längs med och vinkelrätt mot träfibern.</p><p>Slutsatsen från fallet med plana brädor är att det är möjligt att använda anisotropin hos trä och dess påverkan på ett reflekterat elektromagnetiskt fält för att skatta fibervinkeln. Detta är grunden i de metoder som föreslås för cylindriska stockar. För samtliga metoder så gäller att varken fukthalt eller temperatur behöver vara kända på förhand. Eftersom anisotropin kvarstår också för fruset trä så är metoderna användbara även för temperaturer under noll grader Celsius.</p><p>För fallet med cylindriska stockar används känslighetsanalys på både närfälts- och fjärrfältsmetoderna för att analysera parameterberoendet i uppmätt data samt felen som introduceras av brus. I den här känslighetsanalysen används Cram\'{e}r-Rao gränsen som ger den bästa möjliga variansen för skattning av parametrarna. Nivåerna på gränserna är höga vilket indikerar att det är ett svårt estimeringsproblem. Möjligheterna att skatta parametrarna noggrant förbättras genom bättre signal-brus förhållande, upprepade mätningar samt ökad antennstyrka. Känslighetsanalysen är också användbar som ett analytiskt verktyg för ökad förståelse för problem och möjligheter relaterade till metoden för att skatta parametrarna och som ett praktiskt stöd för design av en mätuppställning.</p><p>Enligt avhandlingen är skattning av fibervinkel möjlig med mikrovågor. De föreslagna metoderna är snabba och lämpliga att utveckla vidare för användning i skogen eller i sågverk.</p>

There are hints coming from some scenarios of modern String and Quantum Gravity theories that Lorentz invariance may not be an exact symmetry of Nature. The study of Lorentz violating theories therefore provides an insight into ultraviolet physics. We employ the Effective Field Theory technique to study the most general extension of the Standard Model and its Supersymmetric modifications with Lorentz-violating interactions of mass dimension five. We provide a complete classification of the interactions in these theories and determine a typical experimental sensitivity to the size of Lorentz violation. A detailed study of the operators that induce CPT-odd Electric Dipole Moments is performed and it is shown that they yield an independent constraint on Lorentz violating physics. We provide an application of Lorentz violating physics to the problem of generation of baryon asymmetry of the universe. A scenario of Leptogenesis driven by CPT-odd interactions is considered and confronted with experimental constraints on Lorentz-violating physics.

As an operational approach to the Bekenstein-Hawking formula S_{BH}=A/4l_{Pl}^{2} for the black hole entropy, we consider the reversible contraction of a spinning thin shell to its event horizon and find that its thermodynamic entropy approaches $S_{\mathrm{BH}}$. In this sense the shell, called a "black shell", imitates and is externally indistinguishable from a black hole. Our work is a generalization of the previous result [10] for the spherical case. We assume the exterior space-time of the shell is given by the Kerr metric and match it to two different interior metrics, a vacuum one and a non-vacuum one. We find the vacuum interior embedding breaks down for fast spinning shells. The mechanism is not clear and worth further exploring. We also examine the case of a Kerr-AdS exterior, without trying to find a detailed interior solution. We expect the same behavior of the shell when the horizon limit is approached.

Raman spectroscopy is a form of vibrational spectroscopy that is capable of probing biological samples at a molecular level. In this work it was used in the analysis of ionizing radiation-induced damage in DNA. Spectra of both simple, short-stranded DNA oligomers (SS-DNA) and the more complicated calf-thymus DNA (CT-DNA) were acquired before and after irradiation to a variety of doses from 0 to ~2000 Gy. In a technique known as ultraviolet resonance Raman spectroscopy (UVRRS), three UV wavelengths of 248, 257 and 264 nm were utilized in order to selectively enhance contributions from different molecular groups within the samples. Assignment of the spectral peaks was aided by the literature, as well as through analysis of UVRR spectra of short strands of the individual DNA bases obtained at each of the three incident UV wavelengths. Difference spectra between the irradiated and unirradiated samples were calculated and the samples exposed to ~2000 Gy showed significant radiation-induced features. Intensity increases of spectral peaks, observed primarily in the CT-DNA, indicated unstacking of the DNA bases and disruption of Watson-Crick hydrogen bonds, while intensity decreases of spectral peaks, observed only in the SS-DNA, indicated both base damage and the loss of structural integrity of the DNA molecule. The high molecular specificity of UVRRS allowed for precise identification of the specific bonds affected by the radiation, and the use of the varying incident wavelengths allowed for the observation of damage to moieties that would otherwise have been excluded. The use of UVRRS shows promise in the study of radiation-induced damage to DNA and would be well suited for extension to the study of more complicated biological systems.