Master's thesis is dealing with desgin of a measuring unit incorporating inertial sensors, used for analysis in canoe sprint. Data from a three-axis accelerometer and a three-axis gyroscope were combined using an extended Kalman filter, yielding speed, roll, pitch and yaw of the boat and stroke rate. Calculated values were verified by a GPS. Furthermore, parameters describing dynamic behaviour of the system were identified, allowing an inclusion of dynamic quantities like force and power into the analysis.

This Ph.D. thesis deals with problems about voltage dips and short voltage interruptions, generally named as voltage events, which origin in power supply networks and have a negative influence for all connected electric appliances. In this thesis single phase appliances are considered. These problems closely relate with area of electromagnetic compatibility which solve all questions about correct operation of different types of electric appliances during electromagnetic disturbances impact. Voltage events are ones of the many types of electromagnetic disturbances. The connection between disturbance sources and sensitive electric appliances is created by power supply lines. The immunity of electric appliances to voltage dips and short interruptions is currently tested via voltage dips with strictly defined parameters which are intended by class of electromagnetic environment in which the usage of electric appliance is recommended. During immunity tests the rectangular shape of voltage dips is preferred. The main descriptive parameters of testing voltage events are the residual voltage and the event time duration. But voltage dips and short interruptions defined by this way do not closely relate with parameters of real voltage dips and interruptions occurred in public supply system where parameters of voltage dips are variable. Moreover in the power supply system there are many of others voltage parameters which can have a significant influence to immunity level of connected electric appliances. This Ph.D. thesis also deals with finding more voltage event parameters. Although the voltage events occurrence in the power supply system is not limited and voltage events are considered only as informative voltage parameter it is important to monitor voltage events occurrence. The monitoring device has to be able to operate for ling time period and it has to detect parameters of voltage events with adequate accuracy. The accuracy of detected event parameters and the detection delay depends on the detection algorithm characteristics. That is why the part of this thesis relates with a comparison of several detection algorithms and their abilities to correct detection of voltage event parameters. The main purpose of this thesis is the proposal of connection between classification of voltage dips and short interruptions occurred in power supply system with the classification of electric appliances immunity to these voltage events. On the base of many of provided electric appliances immunity tests and also on the base of long time period voltage events monitoring the special compatibility levels are proposed in this thesis. The observation of proposed compatibility levels will bring the increasing level of reliable operation of all connected electric appliances.

Les Éoliennes à Entraînement Direct (ÉED) sont équipées de Générateurs Syn- chrones à Aimants Permanents (GSAP). Leurs trois plus courantes défaillances sont la dé- magnétisation, l’excentricité (statique, dynamique et mixte) et le court-circuit inter-tour. L’analyse de la signature du courant de la machine est souvent utilisée pour rechercher des problèmes du générateur, car ces altérations introduisent des harmoniques supplémen- taires dans les courants générés. La Transformée de Fourier Rapide (TFR) est utilisée pour calculer le spectre des courants. Cependant, la TFR permet de calculer l’ensemble du spec- tre, tandis que le nombre de défauts possible et le nombre d’harmoniques introduites sont faibles. L’algorithme de Goertzel, mis en oeuvre sous forme de filtre (le filtre de Goertzel), est présenté comme une alternative plus efficace au TFR. Le spectre des courants change avec la vitesse du vent, ce qui rend la détection plus difficile. Le Filtre de Kalman Étendu (FKÉ) est proposé comme solution. Le spectre de résidus, calcule entre les courants estimés et les courants générés, est constant, quelle que soit la vitesse du vent. Cependant, l’effet des défauts est visible dans leur spectre. Lors de l’utilisation de l’FKÉ, un défi consiste à estime la matrice de covariance pour le bruit du processus. Une nouvelle méthode était développée pour ça, qui n’utilise aucune de maîtrise du filtre. Les ÉED sont placés soit dans des zones éloignées, soit dans des villes. Pour la surveillance des ÉED, des dizaines ou des centaines de kilomètres de câbles sont nécessaires. Les Réseaux de Capteurs sans Fil (RCF) sont bien adaptés pour être utilisés dans l’infrastructure de communication des ÉED. RCF ont des coûts initiaux et d’entretien plus faibles et leurs installations sont rapides. De plus, ils peuvent compléter les réseaux câblés. Différentes technologies sans fil sont comparées : les technologies à grande surface, ainsi que les technologies à courte portée qui supportent des débits de données élevés. / Direct Drive Wind Turbines (DDWTs) are equipped with Permanent Magnet Syn- chronous Generators (PMSGs). Their three most common failures are demagnetization, ec- centricity (static, dynamic and mixed) and inter-turn short circuit. Machine Current Signa- ture Analysis is often used to look for generator problems, as these impairments introduce additional harmonics into the generated currents. The Fast Fourier Transform (FFT) is utilized to compute the spectrum of the currents. However, the FFT calculates the whole spectrum, while the number of possible faults and the number of introduced harmonics is low. The Goertzel algorithm, implemented as a filter (the Goertzel filter), is presented as a more efficient alternative to the FFT. The spectrum of the currents changes with the wind speed, and thus the detection is made more difficult. The Extended Kalman Filter (EKF) is proposed as a solution. The spectrum of the residuals, computed between the estimated and the generated current, is constant, regardless of the wind speed. However, the effect of the faults is visible in the spectrum. When using the EKF, one challenge is to find out the covariance matrix of the process noise. A new method was developed in this regard, which does not use any of the matrices of the filter. DDWTs are either placed in remote areas or in cities. For the monitoring of a DDWT, tens or hundreds of kilometers of cables are necessary. Wireless Sensor Networks (WSNs) are suited to be used in the communication infrastructure of DDWTs. WSNs have lower initial and maintenance costs, and they are quickly installed. Moreover, they can complement wired networks. Different wireless technologies are com- pared - both wide area ones, as well as short range technologies which support high data rates.

Die Fahrzeuglokalisierung ist im Bereich der Fahrerassistenzsysteme von entscheidender Bedeutung und Voraussetzung fur verschiedene Anwendungen der Robotik, wie z.B. Navigation oder Kollisionsvermeidung fur fahrerlose Transportsysteme (FTS). In dieser Arbeit wird ein Verfahren zur Lokalisierung mittels Landmarken vorgestellt, die eine Orientierung bezuglich einer Karte ermoglichen. Dabei werden der Erweiterte- Kalman-Filter und der Partikel-Filter fur diese Aufgabe untersucht und verglichen. Ein Schwerpunkt dieser Betrachtungen stellt dabei der Partikel-Filter dar. Die besondere Problematik der Initialisierung wird ausfuhrlich fur beide Filter dargestellt. Simulationen und Versuche zeigen, dass sich der Partikel-Filter fur eine robuste Lokalisierung der Fahrzeugposition verwenden lasst. Im Vergleich dazu kann der Erweiterte-Kalman-Filter nur im begrenzten Maße eingesetzt werden. / The localization of vehicles is of vital importance in the field of driver assistance systems and a requirement of different applications for robotics, i.e. navigation or collision avoidance for automatic guided vehicle systems. In this thesis an approach for localization by means of landmarks is introduced, which enables an orientation regarding a map. The extended Kalman filter and the particle filter are analyzed and compared. The main focus for this consideration is on the particle filter. The problematic for initialization is discussed in detail for both filters. Simulations and tests prove that the particle filter is suitable for robust localization of the vehicle position. Compared to this, the extended Kalman filter can only be used to a certain extend.

<div>Stoichiometric air-fuel ratio (AFR) and air/EGR flow control are essential control problems in today’s advanced spark-ignited (SI) engines to enable effective application of the three-way-catalyst (TWC) and generation of required torque. External exhaust gas recirculation (EGR) can be used in SI engines to help mitigate knock, reduce enrichment and improve efficiency[1 ]. However, the introduction of the EGR system increases the complexity of stoichiometric engine-out lambda and torque management, particularly for high BMEP commercial vehicle applications. This thesis develops advanced frameworks for sensing and control architecture designs to enable robust air handling system management, stoichiometric cylinder air-fuel ratio (AFR) control and three-way-catalyst emission control.</div><div><br></div><div><div>The first work in this thesis derives a physically-based, control-oriented model for turbocharged SI engines utilizing cooled EGR and flexible VVA systems. The model includes the impacts of modulation to any combination of 11 actuators, including the throttle valve, bypass valve, fuel injection rate, waste-gate, high-pressure (HP) EGR, low-pressure (LP) EGR, number of firing cylinders, intake and exhaust valve opening and closing timings. A new cylinder-out gas composition estimation method, based on the inputs’ information of cylinder charge flow, injected fuel amount, residual gas mass and intake gas compositions, is proposed in this model. This method can be implemented in the control-oriented model as a critical input for estimating the exhaust manifold gas compositions. A new flow-based turbine-out pressure modeling strategy is also proposed in this thesis as a necessary input to estimate the LP EGR flow rate. Incorporated with these two sub-models, the control-oriented model is capable to capture the dynamics of pressure, temperature and gas compositions in manifolds and the cylinder. Thirteen physical parameters, including intake, boost and exhaust manifolds’ pressures, temperatures, unburnt and burnt mass fractions as well as the turbocharger speed, are defined as state variables. The outputs such as flow rates and AFR are modeled as functions of selected states and inputs. The control-oriented model is validated with a high fidelity SI engine GT-Power model for different operating conditions. The novelty in this physical modeling work includes the development and incorporation of the cylinder-out gas composition estimation method and the turbine-out pressure model in the control-oriented model.</div></div><div><br></div><div><div>The second part of the work outlines a novel sensor selection and observer design algorithm for linear time-invariant systems with both process and measurement noise based on <i>H</i>2 optimization to optimize the tradeoff between the observer error and the number of required sensors. The optimization problem is relaxed to a sequence of convex optimization problems that minimize the cost function consisting of the <i>H</i>2 norm of the observer error and the weighted <i>l</i>1 norm of the observer gain. An LMI formulation allows for efficient solution via semi-definite programing. The approach is applied here, for the first time, to a turbo-charged spark-ignited (SI) engine using exhaust gas recirculation to determine the optimal sensor sets for real-time intake manifold burnt gas mass fraction estimation. Simulation with the candidate estimator embedded in a high fidelity engine GT-Power model demonstrates that the optimal sensor sets selected using this algorithm have the best <i>H</i>2 estimation performance. Sensor redundancy is also analyzed based on the algorithm results. This algorithm is applicable for any type of modern internal combustion engines to reduce system design time and experimental efforts typically required for selecting optimal sensor sets.</div></div><div><br></div><div><div>The third study develops a model-based sensor selection and controller design framework for robust control of air-fuel-ratio (AFR), air flow and EGR flow for turbocharged stoichiometric engines using low pressure EGR, waste-gate turbo-charging, intake throttling and variable valve timing. Model uncertainties, disturbances, transport delays, sensor and actuator characteristics are considered in this framework. Based on the required control performance and candidate sensor sets, the framework synthesizes an H1 feedback controller and evaluates the viability of the candidate sensor set through analysis of the structured</div><div>singular value μ of the closed-loop system in the frequency domain. The framework can also be used to understand if relaxing the controller performance requirements enables the use of a simpler (less costly) sensor set. The sensor selection and controller co-design approach is applied here, for the first time, to turbo-charged engines using exhaust gas circulation. High fidelity GT-Power simulations are used to validate the approach. The novelty of the work in this part can be summarized as follows: (1) A novel control strategy is proposed for the stoichiometric SI engines using low pressure EGR to simultaneously satisfy both the AFR and air/EGR-path control performance requirements; (2) A parametrical method to simultaneously select the sensors and design the controller is first proposed for the internal combustion engines.</div></div><div><br></div><div><div>In the fourth part of the work, a novel two-loop estimation and control strategy is proposed to reduce the emission of the three-way-catalyst (TWC). In the outer loop, an FOS estimator consisting of a TWC model and an extended Kalman-filter is used to estimate the current TWC fractional oxygen state (FOS) and a robust controller is used to control the TWC FOS by manipulating the desired engine λ. The outer loop estimator and controller are combined with an existing inner loop controller. The inner loop controller controls the engine λ based on the desired λ value and the control inaccuracies are considered and compensated by the outer loop robust controller. This control strategy achieves good emission reduction performance and has advantages over the constant λ control strategy and the conventional two-loop switch-type control strategy.</div></div>

Micro air vehicles have recently gained popularity due to their potential as autonomous systems. Their future impact, however, will depend in part on how well they can navigate in GPS-denied and GPS-degraded environments. In response to this need, this dissertation investigates a potential solution for GPS-denied operations called relative navigation. The method utilizes keyframe-to-keyframe odometry estimates and their covariances in a global back end that represents the global state as a pose graph. The back end is able to effectively represent nonlinear uncertainties and incorporate opportunistic global constraints. The GPS-denied research community has, for the most part, neglected to consider fixed-wing aircraft. This dissertation enables fixed-wing aircraft to utilize relative navigation by accounting for their sensing requirements. The development of an odometry-like, front-end, EKF-based estimator that utilizes only a monocular camera and an inertial measurement unit is presented. The filter uses the measurement model of the multi-state-constraint Kalman filter and regularly performs relative resets in coordination with keyframe declarations. In addition to the front-end development, a method is provided to account for front-end velocity bias in the back-end optimization. Finally a method is presented for enabling multiple vehicles to improve navigational accuracy by cooperatively sharing information. Modifications to the relative navigation architecture are presented that enable decentralized, cooperative operations amidst temporary communication dropouts. The proposed framework also includes the ability to incorporate inter-vehicle measurements and utilizes a new concept called the coordinated reset, which is necessary for optimizing the cooperative odometry and improving localization. Each contribution is demonstrated through simulation and/or hardware flight testing. Simulation and Monte-Carlo testing is used to show the expected quality of the results. Hardware flight-test results show the front-end estimator performance, several back-end optimization examples, and cooperative GPS-denied operations.

Visual Simultaneous Localisation and Mapping (SLAM) is concerned with simultaneously estimating the pose of a camera and a map of the environment from a sequence of images. Traditionally, sparse maps comprising isolated point features have been employed, which facilitate robust localisation but are not well suited to advanced applications. In this thesis, we present map representations that allow a more dense description of the environment. In one approach, planar features are used to represent textured planar surfaces in the scene. This model is applied within a visual SLAM framework based on the Extended Kalman Filter. We presents solutions to several challenges which arise from this approach.

L'objectif de cette thèse est de proposer l'approche la plus appropriée afin de minimiser le coût d'intégration de petite éolienne dans un micro-réseau DC urbain. Une petit éolienne basé sur un machine synchrone à aimant permanent (MSAP) est considéré à étudier. Un état de l'art concernant les énergies renouvelables, micro-réseau DC, et la production d'énergie éolienne, est fait. Comme le capteur mécanique de cette structure est relativement d'un coût élevé, les différents types de contrôle pour un système de conversion éolienne sont présentés afin de choisir une structure active de conversion d'énergie et un MSAP sans capteur. Par conséquent, un estimateur de vitesse/position est nécessaire pour contrôler le système. Ainsi, les méthodes différentes proposées dans la littérature sont considérées et classifiées à étudier dans les détails, puis les plus efficaces et largement utilisés sont à vérifier dans la simulation et expérimentalement pour le système étudié. Les méthodes choisies sont: estimation de la flux de rotor avec boucle à verrouillage de phase (PLL), observateur à mode glissement (SMO), observateur de Luenberger d'ordre réduit, et filtre de Kalman étendu (EKF). Face à d'autres méthodes, l'estimateur basé sur un modèle EKF permet une commande sans capteur dans une large plage de vitesse et estime la vitesse de rotation avec une réponse rapide. Le réglage des paramètres EKF est le problème principal à sa mise en œuvre. Par conséquent, pour résoudre ce problème, la thèse présente une méthode adaptative, à savoir réglage-adaptatif d’EKF. En conséquence, et grâce à cette approche, le coût total du système de conversion est réduite et la performance est garantie et optimisée. / The aim of this thesis is to propose the most appropriate approach in order to minimize the cost of integration of a wind generator into a DC urban microgrid. A small-scale wind generator based on a permanent magnet synchronous machine (PMSM) is considered to be studied. A state of the art concerning the renewable energies, DC microgrid, and wind power generation is done. As the mechanical sensor for this structure is relatively of high cost, various types of wind conversion system control are presented in order to choose an energy conversion active structure and a sensorless PMSM. Therefore, a speed/position estimator is required to control the system. Thus, different methods proposed in literatures are considered and classified to be studied in details, and then the most effective and widely used ones are to be verified in simulation and experimentally for the studied system. The methods which are chosen are: rotor flux estimation with phase locked loop (PLL), sliding mode observer (SMO), Luenberger observer of reduced order, and extended Kalman filter (EKF). Facing to other methods, the EKF model-based estimator allows sensorless drive control in a wide speed range and estimates the rotation speed with a rapid response. The EKF parameters tuning is the main problem to its implementation. Hence, to solve this problem, the thesis introduces an adaptive method, i.e. adaptive-tuning EKF. As a result and grace to this approach, the total cost of conversion system is reduced and the performance is guaranteed and optimized.

Actuellement, les machines Asynchrones à Double Alimentation (MADA) sont omniprésentes dans le secteur éolien, grâce à leur simplicité de construction, leur faible coût d’achat et leur robustesse mécanique ainsi que le nombre faible d’interventions pour la maintenance. Cependant, comme toute autre machine électrique, ces génératrices sont sujettes aux défauts de différent ordre (électrique, mécanique, électromagnétique…) ou de différents types (capteur, actionneur ou composants du système). C’est pourquoi, il est primordial de concevoir une approche de diagnostic permettant de manière anticipée, de détecter, localiser et identifier tout défaut ou anomalie pouvant altérer le fonctionnement sain de ce type de machine. Motivés par les points forts des méthodes de diagnostic de défauts à base d’observateurs, nous proposons d’une part, dans cette thèse, une approche de détection, localisation et identification des défauts de la MADA d’une éolienne à vitesse variable, à base des observateurs de Kalman, performants et largement utilisés. Les erreurs d’estimation d’état du filtre de Kalman linéaire et de ses variantes non-linéaires, à noter : le Filtre de Kalman Etendu (EKF) et le Filtre de Kalman sans-Parfum (UKF), sont utilisés comme résidus sensibles aux défauts. En vue d’éviter les fausses alarmes et de découpler les défauts des perturbations et des bruits, l’analyse des résidus générés est réalisée par des tests statistiques tels que : Test de Page Hinkley (PH) et Test DCS (Dynamic Cumulative Sum). Pour la localisation des défauts multiples et simultanés, la Structure d’Observateurs Dédiés (DOS) et la Structure d’Observateurs Généralisés (GOS) sont appliquées. De plus, l’amplitude du défaut est déterminée dans l’étape d’identification de défaut. Les défauts capteurs, actionneurs et composants de la MADA, sont traités dans ce travail de recherche. D’autre part, une étude comparative entre les différents observateurs de Kalman, est élaborée. La comparaison porte sur les critères suivants : le temps de calcul, la précision et la vitesse de convergence des estimations. / Actually, the Doubly Fed Induction Generators (DFIG) are omnipresent in the wind power market, owing to their construction simplicity, their low purchase cost and their mechanical robustness. However, as any other electrical machine, these generators are subject to defects of different order (electrical, mechanical, electromagnetic ...) or of different type (sensor, actuator or system). That’s why, it is important to design an effective diagnostic approach, able to early detect, locate and identify any defect or abnormal behavior, which could undermine the healthy operation of this machine On the one hand, motivated by the observer-based fault diagnosis methods strengths, we proposed, in this thesis, a diagnostic approach for the faults detection, localization and identification of the DFIG used in variable speed wind turbine. This approach is based on the use of the efficient and widely used Kalman observers. The state estimation errors of the linear Kalman filter and the non-linear Kalman filters, named: The Extended Kalman Filter (EKF) and the Unscented Kalman Filter (UKF) are used as faults sensitive residuals. In order to avoid false alarms and to decouple faults from disturbances and noises, the faults detection is carried out by the analysis of the residuals generated, by the mean of statistical tests such as: Hinkley Page Test (PH) and DCS Test (Dynamic) Cumulative Sum). For the localization step in case of multiple and simultaneous faults, the Dedicated Observer scheme (DOS) and the Generalized Observer scheme (GOS) are applied. In addition, the fault level is determined in the fault identification step. Sensor faults, actuator and system faults of DFIG, are treated in this research work. On the other hand, a comparative study between the three Kalman observers proposed is performed. The comparison was done in terms of (1) the computation time, (2) the estimation accuracy, and (3) the convergence speed.

Visual Simultaneous Localisation and Mapping (SLAM) is concerned with simultaneously estimating the pose of a camera and a map of the environment from a sequence of images. Traditionally, sparse maps comprising isolated point features have been employed, which facilitate robust localisation but are not well suited to advanced applications. In this thesis, we present map representations that allow a more dense description of the environment. In one approach, planar features are used to represent textured planar surfaces in the scene. This model is applied within a visual SLAM framework based on the Extended Kalman Filter. We presents solutions to several challenges which arise from this approach.