>Magister Scientiae - MSc / This study reports on the effects of hydrogen dilution and deposition time on six silicon thin films deposited at six specific deposition regimes. The thin film properties are investigated via X-Ray diffraction analysis, raman spectroscopy, fourier transform infra-red spectroscopy, elastic recoil detection analysis, scanning and transmission electron microscopy and UV-visible spectroscopy. This investigation revealed the dominating etching effect of atomic hydrogen with the increase in hydrogen dilution and a bonded hydrogen content (CH) exceeding 10 at.% for each of the six thin films. The optically determined void volume fraction and static refractive index remain constant, for each thin film, with the change in CH

Philosophiae Doctor - PhD / When the amorphous silicon (a-Si) dangling bonds are bonded to hydrogen the concentration of the dangling bond is decreased. The resulting film is called hydrogenated amorphous silicon (a-Si:H). The reduction in the dangling bonds concentration improves the optoelectrical properties of the film. The improved properties of a-Si:H makes it possible to manufacture electronic devices including a solar cell. A solar cell device based on the hydrogenated amorphous silicon (a-Si:H) was fabricated using the Hot-Wire Chemical Vapour Deposition (HWCVD). When an n-i-p solar cell configuration is grown, the norm is that the p-doped layer is deposited from a mixture of silane (SiH4) gas with diborane (B2H6). The boron atoms from diborane bonds to the silicon atoms and because of the number of the valance electrons, the grown film becomes a p-type film. Aluminium is a group 3B element and has the same valence electrons as boron, hence it will also produce a p-type film when it bonds with silicon. In this study the p-doped layer is grown from the co-deposition of a-Si:H from SiH4 with aluminium evaporation resulting in a crystallized, p-doped thin film. When this thin film is used in the n-i-p cell configuration, the device shows photo-voltaic activity. The intrinsic layer and the n-type layers for the solar cell were grown from SiH4 gas and Phosphine (PH3) gas diluted in SiH4 respectively. The individual layers of the solar cell device were characterized for both their optical and electrical properties. This was done using a variety of experimental techniques. The analyzed results from the characterization techniques showed the films to be of device quality standard. The analysed results of the ptype layer grown from aluminium showed the film to be successfully crystallized and doped. A fully functional solar cell was fabricated from these layers and the cell showed photovoltaic activity. / South Africa

Philosophiae Doctor - PhD / When the amorphous silicon (a-Si) dangling bonds are bonded to hydrogen the concentration of the dangling bond is decreased. The resulting film is called hydrogenated amorphous silicon (a-Si:H). The reduction in the dangling bonds concentration improves the optoelectrical properties of the film. The improved properties of a-Si:H makes it possible to manufacture electronic devices including a solar cell.A solar cell device based on the hydrogenated amorphous silicon (a-Si:H) was fabricated using the Hot-Wire Chemical Vapour Deposition (HWCVD). When an n-i-p solar cell configuration is grown, the norm is that the p-doped layer is deposited from a mixture of silane (SiH4) gas with diborane (B2H6). The boron atoms from diborane bonds to the silicon atoms and because of the number of the valance electrons, the grown film becomes a p-type film. Aluminium is a group 3B element and has the same valence electrons as boron, hence it will also produce a p-type film when it bonds with silicon.In this study the p-doped layer is grown from the co-deposition of a-Si:H from SiH4 with aluminium evaporation resulting in a crystallized, p-doped thin film. When this thin film is used in the n-i-p cell configuration, the device shows photo-voltaic activity.The intrinsic layer and the n-type layers for the solar cell were grown from SiH4 gas and Phosphine (PH3) gas diluted in SiH4 respectively. The individual layers of the solar cell device were characterized for both their optical and electrical properties. This was done using a variety of experimental techniques. The analyzed results from the characterization techniques showed the films to be of device quality standard. The analysed results of the ptype layer grown from aluminium showed the film to be successfully crystallized and doped.A fully functional solar cell was fabricated from these layers and the cell showed photovoltaic activity.

Ce travail est une contribution à l'étude de l'interaction entre des couches minces de silicium amorphe hydrogéné (a-Si:H) et un plasma d'hydrogène, dans un réacteur de dépôt par PECVD (Plasma Enhanced Chemical Vapor Deposition). Le suivi in situ de la cinétique de gravure par l'hydrogène atomique est réalisé par ellipsométrie UV-visble. Les différents paramètres de plasma (température, puissance radiofréquence, pression du gaz H2, type de dopage du matériau) pouvant impacter cette cinétique ont été sondés. L'analyse des spectres d'ellipsométrie spectroscopique, à l'aide d'un modèle optique approprié, a permis de mettre en évidence leurs effets sur le temps de formation de la couche modifiée par l'hydrogène, son épaisseur et son excès d'hydrogène, ont été analysés. Le même traitement au plasma d'hydrogène appliqué à des jonctions i/p et i/n, révèle un comportement particulier de la cinétique de gravure dans la zone de jonction. Ce comportement a été interprété dans le cadre d'un modèle simple de diffusion de l'hydrogène sous champ électrique. / This work is a contribution to the study of the interaction between hydrogenated amorphous silicon (a-Si:H) thin films and hydrogen plasma in a PECVD (Plasma Enhanced Chemical Vapor Deposition) reactor. The kinetics of silicon etching by atomic hydrogen is monitored in situ by UV - visble ellipsometry .Several plasma parameters (temperature, RF power, H2 gas pressure, the doping of the material) that may impact the kinetics were probed. An analysis of the spectroscopic ellipsometry spectra, thanks to an appropriate optical model, allowed evidencing their effects on the time constant, the thickness and the hydrogen excess of the H-modified layer.The same hydrogen plasma treatment repeated on i/p and i/n H base junctions revealed a particular behavior of the etching kinetics in the junction zone. This effect is interpreted in the frame of a simple of hydrogen diffusion model under an electric field.

Apresentamos neste trabalho uma técnica alternativa para a obtenção de filmes finos de silício amorfo hidrogenado (&#945-Si:H). Nós depositamos &#945-Si:H em um sistema de deposição que utiliza descarga luminescente a baixas freqüências (60Hz). Para tanto, nós projetamos todo o reator para que este objetivo pudesse ser atingido. Os filmes obtidos por nós mostram propriedades ópticas e eletrônicas bastante próximas aquelas dos filmes produzidos pela técnica convencional de descarga luminescente a radiofreqüência (13,56 MHz). A temperatura do substrato ótima para a técnica de descarga luminescente a baixas freqüências está na faixa 150-170&#176C, em torno de 100&#176C menor do que aquela usada para radiofreqüência. Neste trabalho nós apresentamos medidas das propriedades dos filmes, incluindo condutividade no escuro, fotocondutividade, comprimento de difusão ambipolar, absorção no infra-vermelho, gap óptico, e densidade de defeitos de níveis profundos. Para realizar parte destas medidas, nós construímos sistemas experimentais de caracterização exclusivos para o &#945-Si:H. / In this work we present an alternative technique for producing hydrogenated amourphous silicon thin films (&#945-Si:H). We deposited &#945-Si:H in a low-frequency (60 Hz) glow-discharge deposition system. For this purpose, we designed completely the reactor. The films we produced show electronic and optical properties nearly equivalent to those of films prepared by the conventional radio-frequency (13,56 MHz) glow-discharge technique. The optimal substrate temperature for the low-frequency glow-discharge technique is 150-170&#176C, about 100&#176C lower than that radio-frequency. In this work, we report measurements of film properties, including dark conductivity, photoconductivity, ambipolar diffusion lenght, infrared absorption, optical band gap, and deep defect density. To do these measurements, we assembled experimental systems used to characterize &#945-Si:H.

This thesis investigates the possibility of enhancing the efficiency of thin film solar cells by including periodic material nonhomogeneities in combination with periodically corrugated back reflectors. Two different types of solar cell are investigated; p-i-n junctions solar cells made from alloys of hydrogenated amorphous silicon (a-Si:H) (containing either carbon or germanium), and Schottky barrier junction solar cells made from alloys of indium gallium nitride (InξGa1-ξN). Material nonhomogeneities are produced by varying the fractions of the constituent elements of the alloys. For example, by varying the content of carbon or germanium in the a-Si:H alloys, semiconductors with bandgaps ranging from 1:3 eV to 1:95 eV can be produced. Changing the bandgap alters both the optical and electrical properties of the material so this necessitates the use of coupled optical and electrical models. To date, the majority of solar cell simulations either prioritise the electrical portion of the simulation or they prioritise the optical portion of the simulation. In this thesis, a coupled optoelectronic model, developed using COMSOL Multiphysics®, was used to simulate solar cells: a two-dimensional finite-element optical model, which solved Maxwell's equations throughout the solar cells, was used to calculate the absorption of incident sunlight; and a finite-element electrical drift-diffusion transport model, either one- or two-dimensional depending on the symmetries of the problem, was used to calculate the steady state current densities throughout the solar cells under external voltage biases. It is shown that a periodically corrugated back reflector made from silver can increase efficiency of an a-Si:H alloy single p-i-n junction solar cell by 9:9% compared to a baseline design, while for a triple junction the improvement is a relatively meagre 1:8%. It is subsequently shown that the efficiency of these single p-i-n junction solar cells with a back reflector can be further increased by the inclusion of material nonhomogeneities, and that increasing the nonhomogeneity progressively increases efficiency, especially in thicker solar cells. In the case of InξGa1-ξN Schottky barrier junction solar cells, the gains are shown to be even greater. An overall increase in efficiency of up to 26:8% over a baseline design is reported.

In this dissertation, the electrical characteristics of generally used hydrogenated amorphous silicon (a-Si:H) TFTs in LCD and newly risen amorphous indium-gallium-zinc oxide (a-IGZO) TFTs were studied. For modern mobile display and large-size flat panel display application, the traditional thin-film transistor-liquid crystal display (TFT-LCD) technology confronts with a lot of challenges and problems. In general, flexible displays must exhibit some bending ability; however, bending applies mechanical strain to electronic circuits and affects device characteristics. Therefore, the electrical characteristics of a-Si:H TFTs fabricated on stainless steel foil substrates with uniaxial bending were investigated at different temperatures. Experimental results showed that the on-state current and threshold voltage degraded under outward bending. This is because outward bending will induce the increase of band tail states, affecting the transport mechanism at different temperatures. In addition, for practical operation, the electrical characteristics of a-Si:H TFTs under flat and bending situations after AC/DC stress at different temperatures were studied. It was found that high temperature and mechanical bending played important roles under AC stress. The dependence between the accumulated sum of bias rising and falling time and the threshold voltage shifts under AC stress was also observed. Because a-Si:H is a photosensitive material, the high intensity backlight illumination will degrade the performance of a-Si:H TFTs. Thus, the photo-leakage current of a-Si:H TFTs under illumination was investigated at different temperatures. Experimental results showed that a-Si:H TFTs exhibited a pool performance at lower temperatures. The indirect recombination rate and the parasitic resistance (Rp) are responsible for the different photo-leakage-current trends of a-Si:H TFTs under varied temperature operations. To investigate the photo-leakage current, the a-Si:H TFTs were exposed to ultraviolet (UV) light irradiation. It was found that the photo current of a-Si:H TFTs was reduced after UV light irradiation. The detail mechanisms on reducing/increasing photo-leakage current by UV light irradiation were discussed. Recently, the oxide-based semiconductor TFT, especially a-IGZO TFT, is considered as one of promising candidates for active matrix flat-panel display. However, the a-IGZO TFT exists significant electrical instability issue and manufacturing problems. As a consequence, we investigated the effect of hydrogen incorporation on a-IGZO TFTs to reduce interface states between active layer and insulator. Experimental results showed that the electrical characteristics of hydrogen-incorporated a-IGZO TFTs were improved. The threshold voltage shift (£GVth) in hysteresis loop is suppressed from 4 V to 2 V due to the hydrogen-induced passivation of the interface trap states. Finally, we reported the effect of ambient environment on a-IGZO TFT instability. As a-IGZO TFTs were stored in atmosphere environment for 40 days, the transfer characteristics accompanying strange hump were observed during bias-stress. The hump phenomenon is attributed to the absorption of H2O molecule. Additionally, the sufficient electric field is also necessary to cause this anomalous transfer characteristic.

Apresentamos neste trabalho uma técnica alternativa para a obtenção de filmes finos de silício amorfo hidrogenado (&#945-Si:H). Nós depositamos &#945-Si:H em um sistema de deposição que utiliza descarga luminescente a baixas freqüências (60Hz). Para tanto, nós projetamos todo o reator para que este objetivo pudesse ser atingido. Os filmes obtidos por nós mostram propriedades ópticas e eletrônicas bastante próximas aquelas dos filmes produzidos pela técnica convencional de descarga luminescente a radiofreqüência (13,56 MHz). A temperatura do substrato ótima para a técnica de descarga luminescente a baixas freqüências está na faixa 150-170&#176C, em torno de 100&#176C menor do que aquela usada para radiofreqüência. Neste trabalho nós apresentamos medidas das propriedades dos filmes, incluindo condutividade no escuro, fotocondutividade, comprimento de difusão ambipolar, absorção no infra-vermelho, gap óptico, e densidade de defeitos de níveis profundos. Para realizar parte destas medidas, nós construímos sistemas experimentais de caracterização exclusivos para o &#945-Si:H. / In this work we present an alternative technique for producing hydrogenated amourphous silicon thin films (&#945-Si:H). We deposited &#945-Si:H in a low-frequency (60 Hz) glow-discharge deposition system. For this purpose, we designed completely the reactor. The films we produced show electronic and optical properties nearly equivalent to those of films prepared by the conventional radio-frequency (13,56 MHz) glow-discharge technique. The optimal substrate temperature for the low-frequency glow-discharge technique is 150-170&#176C, about 100&#176C lower than that radio-frequency. In this work, we report measurements of film properties, including dark conductivity, photoconductivity, ambipolar diffusion lenght, infrared absorption, optical band gap, and deep defect density. To do these measurements, we assembled experimental systems used to characterize &#945-Si:H.

Magister Scientiae - MSc / Amorphous silicon nitride (a-SiN:H) thin films has a multitude of applications, stemming from the tunability of the material properties. Plasma enhanced chemical vapour deposition (PECVD) is the industrial workhorse for production of device quality a-SiN:H. However, this technique has drawbacks in terms of film quality, rooting from ion bombardment, which then results in undesirable oxidation. Hot wire chemical vapour deposition (HWCVD) has shown to be a viable competitor to its more costly counterpart, PECVD. A thin film produced by HWCVD lacks ion bombardment due to the deposition taking place in the absence of plasma. This study will focus on optimising the MVsystems ® HWCVD chamber at The University of the Western Cape, for production of device quality a-SiN:H thin films at low processing parameters. The effect of these parameters on the structural, optical and morphological properties was investigated, for reduction of production costs. The films were probed by heavy ion elastic recoil detection, energy dispersive spectroscopy, Fourier transform infrared spectroscopy, atomic force microscopy, Xray diffraction, and ultraviolet visible spectroscopy. It was shown that silicon rich, device quality a-SiN:H thin films could be produced by HWCVD at wire temperatures as low as 1400 °C and the films showed considerable resistance to oxidation in the bulk.

Magister Scientiae - MSc / Technological advancement has created a market for large area electronics such as solar cells and thin film transistors (TFT’s). Such devices now play an important role in modern society. Various types of conducting, semiconducting and insulating thin films of the order of hundreds, or even tens of nanometres are combined in strata to form stacks to create interactions and phenomena that can be exploited and employed in these devices for the benefit of mankind. One such is for the generation of energy via photovoltaic devices that use thin film technology; these are known as second and third generation solar cells. Silicon and its alloys such as silicon germanium (SiGex), silicon oxide (SiOx), silicon carbide (SiCx) and silicon nitride (SiNx) play an important role in these devices due to the fact that each material in its different structures, whether amorphous, micro or nano-crystalline or completely crystalline, has its own range of unique optical, mechanical and electrical properties. These structures and their material properties can thus exert a huge influence over the overall device performance. viii Chemical vapour deposition (CVD) techniques are most widely used in industry to obtain thin films of silicon and silicon alloys. Source gases are decomposed by the external provision of energy thereby allowing for the growth of a thin solid film on a substrate. In this study a variant of CVD, namely Hot Wire Chemical Vapour Deposition (HWCVD) will be used to deposit thin films of silicon nitride by the decomposition of silane (SiH4), hydrogen (H2) and ammonia (NH3) on a hot tantalum filament (~1600 C). Hydrogenated amorphous silicon nitride (a-SiNx:H) has great potential for application in optoelectronic devices. In commercial solar cell production its potential for use as anti-reflection coatings are due to its intermediate refractive index combined with low light absorption. An additional benefit is the passivation of interface and crystal defects due to the bonded hydrogen. This can lead to better photon conversion efficiency. Its optical properties including optical band gap, Urbach tail, and wavelength-dependent optical constants such as absorption coefficient and refractive index are crucial for the design and application in the relevant optoelectronic device. The final firing step in the production of micro-crystalline silicon solar cells, allows hydrogen to effuse into the solar cell from the a-SiNx:H, and drives bulk passivation of the grain boundaries. We therefore propose the exploration of annealing effects on the thin film structure. The study undertakes a comparison of optical and bonding structure of the as deposited thin film compared to that of the annealed thin film which would have undergone changes due to high temperature annealing under vacuum. However, it is difficult to simultaneously obtain all of these important ix optical parameters for a-SiNx:H thin films. Ultraviolet visible (UV-vis) spectroscopy will be the method of choice to investigate the optical properties. Infrared (IR) spectroscopy is a source of useful information on the microstructure of the material. In particular, the local atomic bonding configurations involving Si, N, and H atoms in a-SiNx:H films can be obtained by Fourier Transform Infrared Spectroscopy (FTIR). Therefore, this study will attempt to establish a relationship between film microstructure of a-SiNx:H thin films and their macroscopic optical properties.