Doctor of Philosophy / Department of Physics / Itzhak Ben-Itzhak / Present laser technology allows for the production of ultra short (&7 fs) intense (.1016 W/cm2)pulses, which are comparable in duration and interaction strength to the vibrational period and the interaction that binds the electron in molecules, respectively. In this intense-field ultra short-pulse regime one can both measure and manipulate dynamics on the femtosecond timescale. To probe the dynamics of laser-matter interactions in this regime, we have chosen to start from the simplest possible molecule - H+ 2 , which can either dissociate into H + p or ionize into p + p + e. We have designed and employ a coincidence three-dimensional momentum imaging technique which allows us to measure ionization and dissociation of a molecular ion beam target simultaneously, while completely separating the two channels from each other. By varying the laser intensity and the pulse duration, we measure the intensity and pulse length dependent momentum distributions for laser induced fragmentation of H+ 2 at 790 nm. These dissociation measurements are in agreement with the phenomena predicted using the adiabatic Floquet picture, e.g. bond softening, in addition to more sophisticated calculations done by solving the time-dependent Schrodinger equation in the Born-Oppenheimer representation. Furthermore, the structure seen in ionization in our measurements and soon after by others is explained via a unified diabatic Floquet picture, which includes both ionization and dissociation in a single intensity and wavelength dependent picture that includes nuclear motion. Additionally, we use the same experimental techniques and apparatus to probe the laser-induced dynamics of multi-electron diatomic molecules, e.g. O+2, N+2, and ND+. The most probable dissociation and ionization pathways producing the features seen in these measurements are discerned using the angular and kinetic-energy-release distributions in conjunction with the diabatic Floquet picture. Finally, we extend these experimental techniques and interpretive models to the simplest polyatomic molecule - H+ 3 , whose fragmentation presents challenges both in our first-of-their-kind experiments and in physical interpretation.

Le regain d'attention des industriels pour les mémoires non volatiles intégrant des nanocristaux, illustré par l'introduction sur le marché de la Flexmemory de Freescale en technologie 90 nm, incite à poursuivre des études sur ce type de systèmes. Pour cela, nous avons mis au point des cellules mémoires élémentaires, à savoir des transistors MOS dont l'oxyde de grille contient une grille granulaire formée par un plan de nanocristaux de silicium (Si-ncx) stockant la charge électrique.Ce travail présente les principaux résultats issus de ces travaux, ceux-ci allant du procédé de fabrication à la caractérisation fine des dispositifs mémoires. Le parfait contrôle de l'élaboration de la grille granulaire de Si-ncx par implantation ionique à très basse énergie (ULE-IBS) est accompagné de caractéristiques « mémoires » répondant aux normes industrielles d'endurance et d'une discrimination des pièges responsables du chargement. Le stockage majoritaire par les Si-ncx est démontré, ce qui est essentiel pour la rétention de la charge. Nous avons développé une technique électrique permettant d'extraire à la fois la quantité de charge stockée par les Si-ncx mais également leurs principales caractéristiques structurales (taille, densité, position dans l'oxyde). Cette extension de la technique électrique de « pompage de charges », non destructive et in-situ permet de suivre l'état du composant en fonctionnement et de caractériser des pièges (e.g. les Si-ncx) pour la première fois au-delà de 3 nm de profondeur dans l'oxyde. Ces résultats ont été validés par des observations TEM. La résolution du pompage de charge étant le piège unique, nous avons alors couplé l'ULE-IBS avec la lithographie « Stencil » pour réduire latéralement le nombre de Si-ncx synthétisés. Cette technique nous permet pour le moment de contrôler la synthèse locale à la position désirée dans l'oxyde de « poches » de Si-ncx de 400 nm. La synthèse de « quelques » Si-ncx est envisagée à très court terme. Nous serons alors en mesure de fabriquer des mémoires à nombre choisi de nanocristaux (par SM-ULE-IBS), dont les propriétés structurales (taille, densité, position) et électriques (quantité de charge stockée) seront vérifiées par pompage de charge, offrant ainsi des outils puissants pour la fabrication et la caractérisation de mémoires à nombre réduit de nanocristaux, notamment pour des longueurs de grilles inférieures à 90 nm / The aim of this thesis has been to fabricate and electrically characterize elementary memory cells containing silicon nanocrystals (Si-ncs), in other words MOSFET which insulating layer (SiO2) contains a Si-ncs array storing the electrical charge. We have shown that we perfectly control the synthesis of a 2D array of 3-4 nm Si-ncs embedded into the MOSFET oxide by low-energy ion implantation (1-3 keV) Reaching this goal implied two key steps: on the one hand develop a reliable MOSFET fabrication process incorporating the Si-ncs synthesis steps and on the other hand develop tools and methods for both memory window and Si-ncs array itself characterizations. We have developed an in-situ characterization technique based on the well-known charge pumping technique, allowing for the first time the extraction of traps depth (e.g. the Si-ncs array) further than 3 nm into the oxide layer leading to the characterization of both position of these Si-ncs into the SiO2 matrix and their structural properties (diameter, density). These results have been confirmed by EF-TEM measurements. Finally, we have worked on the improvement of controlled local synthesis of Si-ncs pockets by combining low-energy ion implantation and stencil lithography. We reduced the size of these pockets down to about 400 nm using this parallel, low cost and reliable technique and identified the limiting effect for the pockets size reduction. These results pave the way for memory cells containing a few Si-ncs with a well-defined position into the oxide and a well-controlled number of ncs

The understanding of multiphase flow properties is essential for the exploitation of hydrocarbon reserves in a reservoir; these properties in turn are dependent on the geometric properties and connectivity of the pore space. The determination of the pore size distribution in carbonate reservoirs remains challenging; carbonates exhibit complex pore structures comprising length scales from nanometers to several centimeters. A major challenge to the accurate evaluation of these reservoirs is accounting for pore scale heterogeneity on multiple scales. This is the topic of this thesis. Conventionally, this micron scale information is achieved either by building stochastic models using 2D images or by combining log and laboratory data to classify pore types and their behaviour. None of these capture the true 3D connectivity vital for flow characterisation. We present here an approach to build realistic 3D network models across a range of scales to improve property estimation through employment of X-ray micro-Computed Tomography (μCT) and Focussed Ion Beam Tomography (FIBT). The submicron, or microporous, regions are delineated through a differential imaging technique undertaken on x-ray CT providing a qualitative description of microporosity. Various 3-Phase segmentation methods are then applied for quantitative characterisation of those regions utilising the attenuation coefficient values from the 3D tomographic images. X-ray micro-CT is resolution limited and can not resolve the detailed geometrical features of the submicron pores. FIB tomography is used to image the 3D pore structure of submicron pores down to a scale of tens of nanometers. We describe the experimental development and subsequent image processing including issues and difficulties resolved at various stages. The developed methodology is implemented on cores from producing wackstone and grainstone reservoirs. Pore network models are generated to characterise the 3D interconnectivity of pores. We perform the simulations of petrophysical properties (permeability and formation resistivity) directly on the submicron scale image data. Simulated drainage capillary pressure curves are matched with the experimental data. We also present some preliminary results for the integration of multiscale pore information to build dual-scale network models. The integration of multiscale data allows one to select appropriate effective medium theories to incorporate sub-micron structure into property calculations at macro scale giving a more realistic estimation of properties.

The development of new materials with novel properties plays an important role in improving our lives and welfare. Research in Nanotechnology can provide e.g. cheaper and smarter materials in applications such as energy storage and sensors. In order for this development to proceed, we need to be able to characterize the material properties at the nano-, and even the atomic scale. The ultimate goal is to be able to tailor them according to our needs. One of the great challenges concerning the characterization of nano-sized objects is how to achieve the physical contact to them. This thesis is focused on the contacting of nanoobjects with the aim of electrically characterizing them and subsequently understanding their electrical properties. The analyzed nanoobjects are carbon nanosheets, nanotetrapods, nanoparticles and molecular systems. Two contacting strategies were employed in this thesis. The first strategy involved the development of a focused ion beam (FIB) based nanocontact platform. The platform consists of gold nanoelectrodes, having nanogaps of 10-30 nm, on top of an insulating substrate. Gold nanoparticles, double-stranded DNA and cadmium telluride nanotetrapods have been trapped in the gaps by using dielectrophoresis. In certain studies, the gold electrodes have also been coated with conducting or non-conducting molecules, prior to the trapping of gold nanoparticles, in order to form molecular junctions. These junctions were subsequently electrically characterized to evaluate the conduction properties of these molecular systems. For the purpose of better controlling the attachment of molecules to the nanoelectrodes, a novel route to synthesize alkanedithiol coated gold nanoparticles was developed. The second contacting strategy was based on the versatility of the FIB instrument as a platform for in-situ manipulation and electrical characterization of non-functionalized and functionalized carbon nanosheets, where it was found that the functionalized samples had an increased conductivity by more than one order of magnitude. Both contacting strategies proved to be valuable for building knowledge around contacting and electrical characterization of nanoobjects

In the last years, there is a rise of interest in investigation and fabrication of nanometer sized magnetic structures due to their various applications (e.g. for data storage or micro sensors). Over the last several decades ion beam implantation became an important tool for the modification of materials and in particular for the manipulation of magnetic properties. Nanopatterning and implantation can be done simultaneously using focused-ion beam (FIB) techniques. FIB implantation and standard ion implantation differ in their beam current densities by 7 orders of magnitude. This difference can strongly influence the structural and magnetic properties, e.g. due to a rise of the local temperature in the sample during ion implantation. In previous investigations both types of implantation techniques were studied separately. The aim of the current research was to compare both implantation techniques in terms of structural changes and changes in magnetic properties using the same material system. Moreover, to separate any possible annealing effects from implantation ones, the influence of temperature on the structural and magnetic properties were additionally investigated. For the current study a model material system which is widely used for industrial applications was chosen: a 50 nm thick non-ordered nano-crystalline permalloy (Ni81Fe19) film grown on a SiO2 buffer layer based onto a (100)-oriented Si substrate. The permalloy films were implanted with a 30 keV Ga+ ion beam; and also a series of as-deposited permalloy films were annealed in an ultra-high vacuum (UHV) chamber. Several investigation techniques were applied to study the film structure and composition, and were mostly based on non-destructive X-ray investigation techniques, which are the primary focus of this work. Besides X-ray diffraction (XRD), providing the long-range order crystal structural information, extended X-ray absorption fine structure (EXAFS) measurements to probe the local structure were performed. Moreover, the film thickness, surface roughness, and interface roughness were obtained from the X-ray reflectivity (XRR) measurements. Additionally cross-sectional transmission electron microscope (XTEM) imaging was used for local structural characterizations. The Ga depth distribution of the samples implanted with a standard ion implanter was measured by the use of Auger electron spectroscopy (AES) and Rutherford backscattering (RBS), and was compared with theoretical TRIDYN calculation. The magnetic properties were characterized via polar magneto-optic Kerr effect (MOKE) measurements at room temperature. It was shown that both implantation techniques lead to a further material crystallization of the partially amorphous permalloy material (i.e. to an increase of the amount of the crystalline material), to a crystallite growth and to a material texturing towards the (111) direction. For low ion fluences a strong increase of the amount of the crystalline material was observed, while for high ion fluences this rise is much weaker. At low ion fluences XTEM images show small isolated crystallites, while for high ones the crystallites start to grow through the entire film. The EXAFS analysis shows that both Ni and Ga atom surroundings have a perfect near-order coordination corresponding to an fcc symmetry. The lattice parameter for both implantation techniques increases with increasing ion fluence according to the same linear law. The lattice parameters obtained from the EXAFS measurements for both implantation types are in a good agreement with the results obtained from the XRD measurements. Grazing incidence XRD (GIXRD) measurements of the samples implanted with a standard ion implanter show an increasing value of microstrain with increasing ion fluence (i.e. the lattice parameter variation is increasing with fluence). Both types of implantation result in an increase of the surface and the interface roughness and demonstrate a decrease of the saturation polarization with increasing ion fluence. From the obtained results it follows that FIB and standard ion implantation influence structure and magnetic properties in a similar way: both lead to a material crystallization, crystallite growth, texturing and decrease of the saturation polarization with increasing ion fluence. A further crystallization of the highly defective nano-crystalline material can be simply understood as a result of exchange processes induced by the energy transferred to the system during the ion implantation. The decrease of the saturation polarization of the implanted samples is mainly attributed to the simple presence of the Ga atoms on the lattice sites of the permalloy film itself. For the annealed samples more complex results were found. The corresponding results can be separated into two temperature regimes: into low (≤400°C) and high (>400°C) temperatures. Similar to the implanted samples, annealing results in a material crystallization with large crystallites growing through the entire film and in a material texturing towards the (111) direction. The EXAFS analysis shows a perfect near-order coordination corresponding to an fcc symmetry. The lattice parameter of the annealed samples slightly decreases at low annealing temperatures, reaches its minimum at about ~400°C and slightly rises at higher ones. From the GIXRD measurements it can be observed that the permalloy material at temperatures above >400°C reaches its strain-free state. On the other hand, the film roughness increases with increasing annealing temperature and a de-wetting of the film is observed at high annealing temperatures. Regardless of the material crystallization and texturing, the samples annealed at low temperatures demonstrate no change in saturation polarization, while at high temperatures a rise by approximately ~15% at 800°C was observed. The rise of the saturation polarization at high annealing temperatures is attributed to the de-wetting effect.

WC-Co cutting tools are widely used in the machining industry. The application of diamond coatings on the surfaces of the tools would prolong the cutting lifetime and improves the manufacturing efficiency. However, direct chemical vapor deposition (CVD) of diamond coatings on WC-Co suffer from severe premature adhesion failure due to interfacial graphitization induced by the binder phase Co. In this research, a combination of hydrochloric acid (HCl) and hydrogen (H2) plasma pretreatments and a novel double interlayer of carbide forming element (CFE)/Al were developed to enhance diamond nucleation and adhesion. The results showed that both the pretreatments and interlayers were effective in forming continuous and adhesive nanocrystalline diamond coatings. The method is a promising replacement of the hazardous Murakami's regent currently used in WC-Co pretreatment with a more environmental friendly approach.<p> Apart from coatings, diamond can be fabricated into other forms of nanostructures, such as nanotips. In this work, it was demonstrated that oriented diamond nanotip arrays can be fabricated by ion beam etching of as-grown CVD diamond. The orientation of diamond nanotips can be controlled by adjusting the direction of incident ion beam. This method overcomes the limits of other techniques in producing nanotip arrays on large areas with controlled orientation. Oriented diamond nano-tip arrays have been used to produce anisotropic frictional surface, which is successfully used in ultra-precision positioning systems.<p> Diamond-like carbon (DLC) has many properties comparable to diamond. In this thesis, the preparation of á-C:H thin films by end-Hall (EH) ion source and the effects of ion energy and nitrogen doping on the microstructure and mechanical properties of the as-deposited thin films were investigated. The results have demonstrated that smooth and uniform á-C:H and á-C:H:N films with large area and reasonably high hardness and Youngs modulus can be synthesized by EH ion source with a low ion energy. The EH ion beam deposition of carbon-based thin films have potential applications such as protective coatings on high capacity magnetic memory disk, for which coating uniformity and smoothness cannot be achieved by the traditional sputtering methods.

WC-Co cutting tools are widely used in the machining industry. The application of diamond coatings on the surfaces of the tools would prolong the cutting lifetime and improves the manufacturing efficiency. However, direct chemical vapor deposition (CVD) of diamond coatings on WC-Co suffer from severe premature adhesion failure due to interfacial graphitization induced by the binder phase Co. In this research, a combination of hydrochloric acid (HCl) and hydrogen (H2) plasma pretreatments and a novel double interlayer of carbide forming element (CFE)/Al were developed to enhance diamond nucleation and adhesion. The results showed that both the pretreatments and interlayers were effective in forming continuous and adhesive nanocrystalline diamond coatings. The method is a promising replacement of the hazardous Murakami's regent currently used in WC-Co pretreatment with a more environmental friendly approach.<p> Apart from coatings, diamond can be fabricated into other forms of nanostructures, such as nanotips. In this work, it was demonstrated that oriented diamond nanotip arrays can be fabricated by ion beam etching of as-grown CVD diamond. The orientation of diamond nanotips can be controlled by adjusting the direction of incident ion beam. This method overcomes the limits of other techniques in producing nanotip arrays on large areas with controlled orientation. Oriented diamond nano-tip arrays have been used to produce anisotropic frictional surface, which is successfully used in ultra-precision positioning systems.<p> Diamond-like carbon (DLC) has many properties comparable to diamond. In this thesis, the preparation of á-C:H thin films by end-Hall (EH) ion source and the effects of ion energy and nitrogen doping on the microstructure and mechanical properties of the as-deposited thin films were investigated. The results have demonstrated that smooth and uniform á-C:H and á-C:H:N films with large area and reasonably high hardness and Youngs modulus can be synthesized by EH ion source with a low ion energy. The EH ion beam deposition of carbon-based thin films have potential applications such as protective coatings on high capacity magnetic memory disk, for which coating uniformity and smoothness cannot be achieved by the traditional sputtering methods.

This thesis addresses the metal nanocluster growth process on prepatterned substrates, the development of atomistic simulation method with respect to an acceleration of the atomistic transition states, and the continuum model of the ion-beam inducing semiconductor surface pattern formation mechanism. Experimentally, highly ordered Ag nanocluster structures have been grown on pre-patterned amorphous SiO^2 surfaces by oblique angle physical vapor deposition at room temperature. Despite the small undulation of the rippled surface, the stripe-like Ag nanoclusters are very pronounced, reproducible and well-separated. The first topic is the investigation of this growth process with a continuum theoretical approach to the surface gas condensation as well as an atomistic cluster growth model. The atomistic simulation model is a lattice-based kinetic Monte-Carlo (KMC) method using a combination of a simplified inter-atomic potential and experimental transition barriers taken from the literature. An effective transition event classification method is introduced which allows a boost factor of several thousand compared to a traditional KMC approach, thus allowing experimental time scales to be modeled. The simulation predicts a low sticking probability for the arriving atoms, millisecond order lifetimes for single Ag monomers and ≈1 nm square surface migration ranges of Ag monomers. The simulations give excellent reproduction of the experimentally observed nanocluster growth patterns. The second topic specifies the acceleration scheme utilized in the metallic cluster growth model. Concerning the atomistic movements, a classical harmonic transition state theory is considered and applied in discrete lattice cells with hierarchical transition levels. The model results in an effective reduction of KMC simulation steps by utilizing a classification scheme of transition levels for thermally activated atomistic diffusion processes. Thermally activated atomistic movements are considered as local transition events constrained in potential energy wells over certain local time periods. These processes are represented by Markov chains of multi-dimensional Boolean valued functions in three dimensional lattice space. The events inhibited by the barriers under a certain level are regarded as thermal fluctuations of the canonical ensemble and accepted freely. Consequently, the fluctuating system evolution process is implemented as a Markov chain of equivalence class objects. It is shown that the process can be characterized by the acceptance of metastable local transitions. The method is applied to a problem of Au and Ag cluster growth on a rippled surface. The simulation predicts the existence of a morphology dependent transition time limit from a local metastable to stable state for subsequent cluster growth by accretion. The third topic is the formation of ripple structures on ion bombarded semiconductor surfaces treated in the first topic as the prepatterned substrate of the metallic deposition. This intriguing phenomenon has been known since the 1960\'s and various theoretical approaches have been explored. These previous models are discussed and a new non-linear model is formulated, based on the local atomic flow and associated density change in the near surface region. Within this framework ripple structures are shown to form without the necessity to invoke surface diffusion or large sputtering as important mechanisms. The model can also be extended to the case where sputtering is important and it is shown that in this case, certain \\lq magic\' angles can occur at which the ripple patterns are most clearly defined. The results including some analytic solutions of the nonlinear equation of motions are in very good agreement with experimental observation.

A challenge exists for understanding the origin of color for structurally colored, 3-dimensional bioorganic nanostructures, such as the scales of butterflies, beetles, and moths. Complex, hierarchical structures found within such scales create the overall scale appearance. The controlled alteration of color through material deposition and the addition of new optical functionalities to such structures are other areas of scientific interest. This dissertation addresses these challenges with a first-of-its-kind, systematic isolation (deconstruction) of scale component nanostructures, followed by evaluation of optical property/structure correlations. The additive deposition (constructive alteration) of emissive materials to structurally-colored templates complements this deconstructive approach towards understanding the origin of color in butterfly scales. Discoveries made through this work may help advance the bioinspired design of synthetic optical structures and subsequent color control through the addition of multilayered, emissive optical components.

The trend for designing of a titanium implant explored using different chemical compositions and crystallinity materials until people realized that the implant surface character was another important factor affecting the rate and extent of osseointegartion. Titanium received a macroporous titania surface layer by anodization, which contains open pores with average pore diameter around 5μm. An additional mesoporous titania top layer was created that followed the contour of the macropores and having 100–200 nm thickness and a pore diameter of 10 nm. Thus, a coherent laminar titania surface layer was obtained producing a hierarchical macro- and mesoporous surface. The interfacial bonding between the surface layers and the titanium matrix was characterized by a scratch test that confirmed a stable and strong bonding of the laminar titania surface layers upon titanium. The wettability to water and the effects on the osteosarcoma cell line (SaOS-2) proliferation and mineralization of the formed titania surface layers were studied systematically by cell culture and scanning electron microscopy (SEM). A synergistic role of the hierarchical macro- and mesoporosities was revealed in terms of enhancing cell adhesion, proliferation and mineralization, when compared with the titania surface with solo porosity scale topography. For the in vivo results of the evaluation of osseointegration, an argon ion beam polishing technique was applied to prepare the cross sections of implants feasible for the high resolution SEM investigation. The interfacial microstructure between newly formed bone and implants with four modified surfaces including the new hierarchical macro- and mesoporous implant surface retrieved after in vivo tests were characterized. By this approach it has become possible to directly observe early bone formation, the increase of bone density, and the evolution of bone structure. The two bone growth mechanisms, distant osteogenesis and contact osteogenesis, can also be distinguished. These direct observations give, at microscopic level, a better view of osseointegration and explain the functional mechanisms of various implant surfaces for osseointegration. / <p>At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 3: In press. Paper 4: Manuscript.</p>