This work involved the development of new perovskite oxides based on SmFeO3 and testing their performances as sensors for reducing gases (H2, CO & CH4) and as anode materials for dry methane oxidation in solid oxide fuel cells. The new perovskite oxide materials with formula Sm0.95Ce0.05Fe1-xMxO3-δ (M= Co, Ni & Cr) were synthesized by a sol gel method using citric acid as a complexing agent. The resulting materials were characterized by using a battery of techniques including XRD, XRF, XPS, SEM and electrochemical methods. Sensing experiments revealed that both cobalt doped and Cr doped materials can detect H2, CO and CH4 in air at different temperatures including room temperature. The Ni doped materials did not prove good candidates as sensors. However, their reduction treatment studies showed the formation of metallic nanoparticles on the surface which deeply influence their electrical conductivity as well as sensing ability. Consequently, this modification in surface structure and chemical composition enabled them to sense hydrogen gas at 300oC very effectively. The response of sensors based on these reduced materials was measurable and reversible. Some materials were also selected on the basis of their reduction stability and electrical properties, and their electrochemical performances were evaluated as SOFC anodes under dry methane and dry hydrogen fuels separately. The performance tests as SOFC anode revealed that the best anode material for the oxidation of dry hydrogen fuel is Sm0.95Ce0.05FeO3-δ. Furthermore, Sm0.95Ce0.05FeO3-δ proved to be coke resistant anode under dry methane fuel and exhibited reasonably low charge transfer resistance values at temperatures between 600-700oC. The doping of Co and Ni at the B-site of Sm0.95Ce0.05FeO3-δ found to be very effective in further improving its performance as SOFC anode towards oxidation of dry methane fuel at the lower temperatures.

Cette thèse présente le développement d'un équipement permettant le dopage Bore des cellules photovoltaïques à base de silicium de type n. Un four de diffusion, appartenant à la société Semco Engineering a été développé pour tirer profit du procédé LYDOP (Leaktight Yield Doping en anglais), breveté par la société. Ce dernier a permis la mise au point d'un procédé de diffusion du Bore, régulé sous basse pression, intégrant une source dopante gazeuse à base de BCl3 afin d'effectuer le dopage de plusieurs plaques de silicium simultanément. Les principaux paramètres influençant le procédé de dopage ont été étudiés pour obtenir un dopage très uniforme sur plaque et sur nacelle. Une large gamme de résistances carrées d'émetteurs (de 40 à 100 ohm/sq) a été obtenue avec une uniformité inférieure à 5% sur plaque et sur nacelle. Le développement du procédé de dopage a conduit à étudier deux méthodes de fabrication d'une cellule photovoltaïque sur silicium multicristallin de type n. Plusieurs méthodes pour la formation de l'émetteur Bore sur une seule face ont été présentées : masquage (SiNx, SiO2), dopage back-to-back ou gravure chimique. De cette étude, deux procédés de fabrication (flowcharts) ont été développés pour la fabrication de cellules photovoltaïques : la première par gravure à l'hydroxyde de potassium (KOH) de l'émetteur, la seconde en effectuant le dopage bore des cellules en position back-to-back (dos à dos). Un rendement sur cellule de 13,2% et 14,4% a été obtenu respectivement pour chacune des flowcharts. Ces résultats, limités principalement par les étapes de passivation et de métallisation permettent de démontrer l'utilisation du procédé Bore comme solution à la formation des émetteurs p+. / This thesis presents the development of an equipment for boron doping of n-type multicrystalline silicon solar cells. A diffusion furnace was developed by Semco Engineering Company. It was built using LYDOP (LeakTight Yields DOPing) technology, patented by Semco. This one permits a simultaneous doping of a big amount of silicon wafers using regulated low pressure processes. Boron diffusion process development was carried out using LYDOP's specifications with BCl3 as gaseous doping source. Main parameters have been studied to control diffusion process. Several sheet resistance values of emitters were achieved (from 40 to 100 ohm/sq) with uniformity under 5% within wafer and within boat by tuning process parameters. Doping process development leads us to investigate how to create a single side emitter with n-type multicrystalline solar cells. Two fabrications flowcharts were presented: one using KOH emitter etches on backside and the other using back-to-back positioning during boron diffusion. Comparison between both flowcharts carried out to 13,2% and 14,4% efficiencies solar cells, respectively on each flowchart. Results are limited by passivation and metallization of emitters. However boron diffusion process demonstrate that LYDOP technology is well adapted to develop n-type solar cells.

A l’heure où les impacts du changement climatique sont devenus indéniables, le développement des énergies décarbonées s’impose. Potentiellement bas coût comparées aux technologies établies, les technologies organiques émergentes offrent une alternative éco-efficiente pour l’exploitation de l’énergie solaire et de l’énergie thermique (< 473 K). Dans le premier chapitre, les avantages et inconvénients des différentes technologies actuellement développées sont discutés. Les dispositifs photovoltaïques, tout comme thermoélectriques, requièrent deux types de matériaux conduisant respectivement les trous (type p) et les électrons (type n). Malgré des avancées remarquables, le développement de semi-conducteurs de type n constitue un levier d’amélioration majeur pour les technologies organiques. Dans ce contexte, ce travail doctoral présente la conception, la synthèse, la caractérisation et la mise en œuvre au sein de dispositifs, de polymères et petites molécules pi-conjugués de type n.Basées sur trois unités électro acceptrices – l’isoindigo (ISI), le naphtalène diimide (NDI) et le benzodifurandione-oligo(p-phénylènevinylène) fluoré (FBDOPV) – la conception et la synthèse de copolymères alternés sont présentées dans le deuxième chapitre. Ces polymères démontrent de hautes affinités électroniques comprises entre 3,5 eV et 4,1 eV. Les études de modélisations DFT et de diffraction de rayons X en couches minces ont permis d’identifier les principaux facteurs structuraux à l’origine des hautes mobilités en électron obtenues en transistor organique à effet de champ allant jusqu’à 0,26 cm2.V-1.s-1.Pour une application thermoélectrique, le dopage moléculaire de ces semi conducteurs organiques est requis et fait l’objet du troisième chapitre. Les conditions nécessaires à la thermo- et photo activation du dopant N-DMBI ont été identifiées. En particulier, la dégradation du dopant activé en présence d’oxygène a été mise en évidence par diffraction de rayons X sur monocristaux. Les polymères et deux petites molécules à base d’ISI et NDI ont été dopés avec succès. Les mécanismes de dopage et les conductivités obtenues sont discutés au cas par cas à l’aide d’expériences spectroscopiques UV Visible-Proche-Infrarouge et Résonance Paramagnétique Electronique. Des conductivités de l’ordre de 10-4 S.cm-1 sont obtenues sans apport énergétique ni avant ni après dépôt. Des conductivités encourageantes de l’ordre de 10-3 S.cm-1 pour une petit molécule à base de NDI et de 10-2 S.cm-1 pour un polymère à base de FBDOPV ont été atteintes. La stabilité et la réversibilité des conductivités des couches minces exposées à l’air ont été examinées et corrélées au niveau LUMO des matériaux. Le contrôle minutieux des conditions de dépôts et de dopage ont permis l’obtention d’un facteur de puissance de l’ordre de 0,3 µW.m 1.K-2 associé à une conductivité thermique de 0,53 W.m-1.K-1. Des figures de mérite d’environ 2.10-4 à 303 K et 5.10-4 à 388 K ont été mesurées, lesquelles représentent les premières valeurs reportées à ce jour pour un semi-conducteur organique dopé n sur un même dispositif.Ces matériaux permettent également le remplacement des dérivés fullerènes en dispositif photovoltaïque comme présenté dans le dernier chapitre. Ils démontrent notamment de forte propriétés d’absorption, étendue jusqu’au domaine proche infrarouge pour l’un des polymères. Un rendement de conversion de 1,3% a été obtenu en cellule solaire à hétérojonction en volume « tout-polymère » avant optimisation. Suivant une conception moléculaire de type donneur-espaceur-accepteur, deux dérivés d’ITIC ont été conçus et caractérisées. La modification de substituants alkyles sur l’espaceur permet d’obtenir des propriétés d’absorptions et d’organisations améliorées comparé à ITIC. De hautes tensions de circuit-ouvert allant jusqu’à 1,10 V et des rendements de 4,2% ont été obtenus avec ces accepteurs non-fullerènes. / At a time when the impacts of climate change have become undeniable, the development of low-carbon energies is crucial. Potentially low cost compared to established technologies, emerging organic technologies offer an eco-efficient alternative for harvesting solar and thermal (< 473 K) energies. In the first chapter, the advantages and drawbacks of the different technologies currently being developed are discussed. Photovoltaic devices, like thermoelectric devices, require two types of materials conducting holes (p type) and electrons (n-type) respectively. Despite remarkable advances, the development of n-type semiconductors represents a major lever for improving organic technologies. In this context, this doctoral work presents the design, synthesis, characterization and device developments of innovative pi-conjugated n-type polymers and small molecules.Based on three electron-accepting units – isoindigo (ISI), naphthalene diimide (NDI) and fluorinated benzodifurandione-oligo(p-phenylenevinylene) (FBDOPV) – the design and synthesis of alternated copolymers are presented in the second chapter. These polymers exhibit high electron affinities ranging from 3.5 eV to 4.1 eV. DFT modelling and thin-film X-ray diffraction studies allowed to identify the main structural aspects leading to electron mobility as high as 0.26 cm2.V 1.s 1 achieved in organic field effect transistors.For thermoelectricity, molecular doping of these organic semiconductors is required. It is the subject of the third chapter. The necessary conditions for thermo- and photo-activation of N DMBI dopant have been identified. In particular, the degradation of the activated dopant in the presence of oxygen has been demonstrated by single crystal X-ray diffraction. Each polymer and two small molecules based on ISI and NDI cores have successfully being doped. The doping mechanisms and conductivities obtained are discussed on a case by case basis using UV-Visible-Near-Infrared and Electron Paramagnetic Resonance spectroscopies. In particular, conductivities in the range of 10-4 S.cm-1 were obtained without external energy supply neither before nor after deposition. Encouraging conductivities in the range of 10-3 S.cm 1 for a small molecule based on NDI and 10-2 S.cm 1 for a polymer based on FBDOPV have been achieved. The stability and reversibility of thin film conductivities when exposed to air were investigated and correlated to the LUMO level of the materials. The thorough control of deposition and doping conditions have afforded to achieve a power factor of about 0.3 µW.m-1.K-2 associated to a thermal conductivity of 0.53 W.m 1.K 1. Figure of merits of approximately 2.10-4 at 303 K and 5.10-4 at 388 K have been obtained, which represent the first values reported to date for an n-doped organic semiconductor measured on a single device.These materials also allow the replacement of fullerene derivatives in photovoltaic devices as presented in the last chapter. In particular, they demonstrate strong absorption properties, extended to the near infrared domain for one of the polymers. A conversion efficiency of 1.3% was obtained in all polymer bulk-heterojunction solar cell before optimization. Following the donor-spacer-acceptor approach, two ITIC derivatives have been designed and characterized. The modification of alkyl substituents on the spacer provides improved absorption and molecular packing properties compared to ITIC. High open-circuit voltages up to 1.10 V and conversion efficiencies of 4.2% have been achieved with these non-fullerene acceptors.

京都大学 / 0048 / 新制・課程博士 / 博士(医学) / 甲第20080号 / 医博第4173号 / 新制||医||1018(附属図書館) / 33196 / 京都大学大学院医学研究科医学専攻 / (主査)教授 長船 健二, 教授 川口 義弥, 教授 小川 修 / 学位規則第4条第1項該当 / Doctor of Medical Science / Kyoto University / DFAM

The semiconducting properties of a bithiophene-naphthalene diimide copolymer (PNDIT2) prepared by Ni-catalyzed chain-growth polycondensation (P1) and commercially available N2200 synthesized by Pd-catalyzed step-growth polycondensation were compared. Both polymers show similar electron mobility of [similar]0.2 cm2 V−1 s−1, as measured in top-gate OFETs with Au source/drain electrodes. It is noteworthy that the new synthesis has several technological advantages compared to traditional Stille polycondensation, as it proceeds rapidly at room temperature and does not involve toxic tin-based monomers. Furthermore, a step forward to fully printed polymeric devices was achieved. To this end, transistors with PEDOT:PSS source/drain electrodes were fabricated on plastic foils by means of mass printing technologies in a roll-to-roll printing press. Surface treatment of the printed electrodes with PEIE, which reduces the work function of PEDOT:PSS, was essential to lower the threshold voltage and achieve high electron mobility. Fully polymeric P1 and N2200-based OFETs achieved average linear and saturation FET mobilities of >0.08 cm2 V−1 s−1. Hence, the performance of n-type, plastic OFET devices prepared in ambient laboratory conditions approaches those achieved by more sophisticated and expensive technologies, utilizing gold electrodes and time/energy consuming thermal annealing and lithographic steps. / Dieser Beitrag ist aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.

The well-known lanthanide cuprates exist in two principal forms, T and T´, which behave as p-type and n-type conductors, respectively. In order to understand the structural properties and crystal chemistry from the T to T´ phase, the Nd₁.₈₋ₓLaₓPr₀.₂CuO₄ (NLPCO) system was studied varying the La substitution ratio (0≤x≤1.8) and then characterised using high temperature X-ray powder diffraction. From analysis of the X-ray diffraction patterns obtained at room temperature, there are clearly five distinguishable regions for the NLPCO system. They are, (1) monophasic T´ solid–solution (2) two phase mixture T´ + T´´ (3) monophasic T´´solid–solution (4) two phase mixture T´´ + O and finally (5) monophasic O phase solid–solution. The T´´ form has previously been suggested as an ordered form of T´; however here we show via high temperature X-ray diffraction studies that it is a non-transformable metastable phase formed on quenching of the T phase via an orthorhombically distorted variant. Also neutron diffraction and selected area electron diffraction (SAED) studies confirmed that the T ´´phase is 4- fold Cu coordinated. The structural, magnetic and electrical properties of this NLPCO series have been investigated for the selected compositions using X-ray diffraction, magnetization measurements, thermal analysis and conductivity measurements. The aim of the second half of this work was to discover the basic high temperature electrical characteristics of Nd₂₋ₓPrₓCuO₄ and investigate how this matches with those required for components on the SOFC cathode side to identify which dopant level shows highest conductivity and whether it is stable at different temperatures. The idea was to make a new concept in SOFC cathodes and current collector development, using n-type conductors instead of p- type conductors and to try to produce a high conductivity material which is stable under the chemical and thermal stresses that exist while under load that can be used in cathode or current collector applications. The Nd₂₋ₓPrₓCuO₄ (NPCO) series has been studied over a range of dopant levels (x=0.15 - 0.25) and maximum conductivity of 86.7 Scm⁻¹ has been obtained for the composition where x = 0.25. Also NPCO shows n-type semiconductor behaviour which gives operational advantages when operating at mild oxygen deficiency. AC impedance studies have been carried out on symmetrical cells to investigate the performance of NPCO as a cathode material. These studies mainly focused on polarization resistance and the activation energies of the cells. Low Rp values and low activation energies are obtained for a composite cathode compared to pure cathode material. Two configurations of NPCO as cathode materials were tested, pre-fired and in-siu fired. Pre-fired NPCO exhibited better performance than in-situ fired NPCO. Both in-situ and pre-fired current collecting NPCO still showed lowest activation energies which suggest good catalytic activity. From all of these studies, it is evident that the praseodymium doped neodymium cuprate material shows considerable promise as a potential cathode material for solid oxide fuel cell applications.

Le silicium (Si) et le germanium (Ge) sont les matériaux de base utilisés dans les circuits intégrés. Cependant, à cause de leur gap indirect, ces matériaux ne sont pas adaptés à la fabrication de dispositifs d'émission de lumière, comme les lasers ou diodes électroluminescentes. Comparé au Si, le Ge pur possède des propriétés optiques uniques, à température ambiante son gap direct est de seulement 140 meV au-delà du gap indirect tandis qu'il est supérieur à 2 eV dans le cas du Si. Compte tenu du coefficient de dilatation thermique du Ge, deux fois plus grand que celui du Si, une croissance de Ge sur Si à hautes températures suivie d'un refroidissement à température ambiante permet de générer une contrainte en tension dans le Ge. Cependant, l'existence d'un désaccord de maille de 4,2% entre deux matériaux conduit à une croissance Stranski-Krastanov avec la formation des films rugueux et contenant de forte densité des dislocations. Nous avons mis en évidence l'existence d'une fenêtre de température de croissance, permettant de supprimer la croissance tridimensionnelle de Ge/Si. En combinant la croissance à haute température à des recuits thermiques par cycles, une contrainte de 0,30% a pu être obtenue. Le dopage de type n a été effectué en utilisant la décomposition de GaP, ce qui produit des molécules P2 ayant un coefficient de collage plus grand par rapport à celui des molécules P4. En particulier, en mettant en oeuvre la technique du co-dopage en utilisant le phosphore et l'antimoine, nous avons mis en évidence une augmentation de l'émission du gap direct du Ge à environ 150 fois, ce qui constitue l'un des meilleurs résultats obtenus jusqu'à présent. / Silicon (Si) and germanium (Ge) are the main materials used as active layers in microelectronic devices. However, due to their indirect band gap, they are not suitable for the fabrication of light emitting devices, such as lasers or electroluminescent diodes. Compared to Si, pure Ge displays unique optical properties, its direct bandgap is only 140 meV above the indirect one. As Ge has a thermal expansion coefficient twice larger than that of Si, tensile strain can be induced in the Ge layers when growing Ge on Si at high temperatures and subsequent cooling down to room temperature. However, due to the existence of a misfit as high as 4.2 % between two materials, the Ge growth on Si proceeds via the Stranski-Krastanov mode and the epitaxial Ge films exhibits a rough surface and a high density of dislocations. We have evidenced the existence of a narrow substrate temperature window, allowing suppressing the three-dimensional growth of Ge on Si. By combining high-temperature growth with cyclic annealing, we obtained a tensile strain up to 0.30 %. The n-doping in Ge was carried out using the decomposition of GaP to produce the P2 molecules, which have a higher sticking coefficient than the P4 molecules. In particular, by implementing a co-doping technique using phosphorus and antimony, we have evidenced an intensity enhancement of about 150 times of the Ge direct band gap emission. This result represents as one of the best results obtained up to now.

Submitted by PPG Engenharia e Tecnologia de Materiais (engenharia.pg.materiais@pucrs.br) on 2018-04-24T14:42:28Z No. of bitstreams: 1 Dissertacao Taila Final.pdf: 2384346 bytes, checksum: 8e3d52f21033cdc04d8f1c3449453ceb (MD5) / Approved for entry into archive by Sheila Dias (sheila.dias@pucrs.br) on 2018-05-08T19:50:29Z (GMT) No. of bitstreams: 1 Dissertacao Taila Final.pdf: 2384346 bytes, checksum: 8e3d52f21033cdc04d8f1c3449453ceb (MD5) / Made available in DSpace on 2018-05-08T20:07:12Z (GMT). No. of bitstreams: 1 Dissertacao Taila Final.pdf: 2384346 bytes, checksum: 8e3d52f21033cdc04d8f1c3449453ceb (MD5) Previous issue date: 2018-02-28 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior - CAPES / The solar cells manufactured in n-type silicon, doped with phosphorus, do not present light induced degradation and they have the potential of achieving high efficiency due to the larger minority charge carrier lifetime. Besides, they are less susceptible to contamination by metal impurities. The aim of this work was to analyze different dopants to obtain the p+ region in n+np+ solar cells manufactured in Czochralski silicon wafers, solar grade, n-type, 120 ?m thick. The acceptor impurities used were B, Al, Ga, GaB and AlGa, deposited by spin-on and diffused at high temperature. The temperature, time and gases used in the process of diffusion were ranged. The sheet resistances (R?) of the diffused regions and the impurity concentration profiles were measured. We concluded that the B and GaB can be diffused at 970? C for 20 min to obtain p+ emitters with values of R? suitable to the production of solar cells with screenprinted metal grid. The Ga and AlGa require high temperatures (greater than 1100? C) and long times to produce doping profiles compatible with the production of solar cells. The Al did not produce low sheet resistance regions, even at temperatures of 1100? C. The use of argon gas instead of the nitrogen did not lead to the decreasing of the sheet resistance. The GaB is the only one doping material analyzed that can be a viable replacement for the B in the production of p+ emitter in n-type solar cells.The GaB was the only one doping material analyzed that allowed the manufacture of solar cells with the maximum efficiency of 13.5%, with the diffusion performed at 1020? C for 20 min. The FF was the main parameter that reduced the efficiency of solar cells doped with GaB when compared to the boron doped cells due to a lower shunt resistance. The n+np+ solar cell, 120 ?m thick, that achieved the highest efficiency was doped with boron and reached 14.9%, a value higher than the previously obtained in studies in the NT-Solar with thin silicon wafers. / As c?lulas solares fabricadas em l?minas de sil?cio tipo n, dopadas com f?sforo, n?o apresentam degrada??o por ilumina??o e t?m potencial de obten??o de maior efici?ncia devido ao maior valor do tempo de vida dos portadores de carga minorit?rios. Adicionalmente, s?o menos suscept?veis ? contamina??o por impurezas met?licas. O objetivo deste trabalho foi realizar uma an?lise de diferentes dopantes para obten??o da regi?o p+ em c?lulas solares n+np+fabricadas em l?minas de sil?cio Czochralski, grau solar, tipo n, com espessura de 120 ?m. Os elementos aceitadores utilizados foram o B, Al, Ga, GaB e AlGa, depositados por spin-on e difundidos em alta temperatura. Foram variadas as temperaturas, os tempos e os gases utilizados no processo de difus?o. Foi medida a resist?ncia de folha (R?) das regi?es difundidas e o perfil de concentra??o de impurezas em fun??o da profundidade. Foram desenvolvidas c?lulas solares com B, Ga, GaB e Al. Verificou-se que o B e GaB podem ser difundidos em temperatura de 970 ?C e por 20 min para obten??o de emissores com valores de R? compat?veis com a produ??o de c?lulas solares metalizadas por serigrafia. O Ga e AlGa necessitam de altas temperaturas (maiores que 1100 ?C) e tempos elevados para produzir perfis de dopantes compat?veis. O Al n?o produziu regi?es p+ de baixa R?, mesmo com a difus?o a 1100 ?C. O uso de Ar para substituir o N2 n?o acarretou em diminui??o da resist?ncia de folha. O GaB foi o ?nico dopante analisado que permitiu a fabrica??o de c?lulas solares com efici?ncia m?xima de 13,5 %, com difus?o a 1020 ?C por 20 min. O fator de forma foi o principal par?metro que reduziu a efici?ncia dos dispositivos com GaB quando comparado ao valor obtido com B devido a menor resist?ncia em paralelo. A c?lula solar n+np+ de 120 ?m de maior efici?ncia produzida neste trabalho foi dopada com boro e atingiu a efici?ncia de 14,9 %, sendo maior que as anteriormente obtidas em trabalhos realizados no NT-Solar com l?minas finas.

Philosophiae Doctor - PhD / Polyaniline nanocomposites doped with poly(vinylsulphonate) (PV-SO3) and nanostructured polystyrene (PSNP) latex beads functionalized with amine (PSNP-NH2) and sulphate ((PSNP-OSO3) were prepared and characterised for use as nitrite electro-catalytic chemosensors and ochratoxin A immunosensors. The resultant polyaniline electrocatalytic chemosensors (PANI, PANI|PSNP-NH2 or PANI|PSNP-OSO3 −) were characterized by cyclic voltammetry (CV), ultraviolet-visible (UV-Vis) spectroscopy and scanning electron microscopy (SEM). Brown-Anson analysis of the multi-scan rate CV responses of the various PANI films gave surface concentrations in the order of 10−8 mol/cm. UV-vis spectra of the PANI films dissolved in dimethyl sulphoxide showed typical strong absorbance maxima at 480 and 740 nm associated with benzenoid p-p* transition and quinoid excitons of polyaniline, respectively. The SEM images of the PANI nanocomposite films showed cauliflower-like structures that were <100 nm in diameter. When applied as electrochemical nitrite sensors, sensitivity values of 60, 40 and 30 μA/mM with corresponding limits of detection of 7.4, 9.2 and 38.2 μM NO2 −, were obtained for electrodes, PANI|PSNP-NH2, PANI and PANI|PSNP-SO3 −; respectively. Immobilisation of ochratoxin A antibody onto PANI|PSNP-NH2, PANI and PANI|PSNPSO3 - resulted in the fabrication of immunosensors. / South Africa

<p>Polyaniline nanocomposites doped with poly(vinylsulphonate) (PV-SO3 &minus / ) and nanostructured polystyrene (PSNP) latex beads functionalized with amine (PSNP-NH2) and sulphate (PSNP-OSO3 &minus / ) were prepared and characterised for use as nitrite electro-catalytic chemosensors and ochratoxin A immunosensors. The resultant polyaniline electrocatalytic chemosensors (PANI, PANI|PSNP-NH2 or PANI|PSNP-OSO3 &minus / ) were characterized by cyclic voltammetry (CV), ultraviolet-visible (UV-Vis) spectroscopy and scanning electron microscopy (SEM). Brown-Anson analysis of the multi-scan rate CV responses of the various PANI films gave surface concentrations in the order of 10&minus / 8 mol/cm. UV-vis spectra of the PANI films dissolved in dimethyl sulphoxide showed typical strong absorbance maxima at 480 and 740 nm associated with benzenoid p-p* transition and quinoid excitons of polyaniline, respectively. The SEM images of the PANI nanocomposite films showed cauliflower-like structures that were &lt / 100 nm in diameter. When applied as electrochemical nitrite sensors, sensitivity values of 60, 40 and 30 &mu / A/mM with corresponding limits of detection of 7.4, 9.2 and 38.2 &mu / M NO2 &minus / , were obtained for electrodes, PANI|PSNP-NH2, PANI and PANI|PSNP-SO3 &minus / , respectively. Immobilisation of ochratoxin A antibody onto PANI|PSNP-NH2, PANI and PANI|PSNPSO3 - resulted in the fabrication of immunosensors.</p>