Presented in this thesis are the following experimental and theoretical investigations carried out on the three-layer electromagnetically coupled (EMC) circular microstrip antennas and their arrays. 1.Three-Layer EMC Circular Microstrip Antenna A three-layer EMC circular microstrip antenna consists of a probe-fed circular microstrip patch having two parasitically excited circular microstrip patches (without ground planes) stacked above it, with air gaps in between successive substrates. In the "inverted" configuration, the parasitic patches are on the lower (nearer to the driven substrate) surface of the substrate. An exhaustive experimental study of the resonant frequencies, input impedance, impedance bandwidth and radiation characteristics of this antenna, has been carried out for both the "normal" and the "inverted" configurations. Based on this experimental study, the design and optimisation of the antenna have been discussed and experimentally tested. In the S-band, it is found that an impedance bandwidth as high as 20 percent coupled with good patterns, high gain and low cross-polarisation levels, have been obtained. 2.Three-Layer EMC Circular Microstrip Antenna Arrays Experimental work has also been carried out on linear arrays of three-layer EMC circular microstrip antennas. The design of a linear array both in the E- and H- planes, of the three-layer microstrip antennas in their "normal" as well as "inverted" configurations, has been discussed and realisation carried out. Impedance bandwidths of the arrays have been experimentally found to be the same as that of the three-layer antenna element High gain and good pattern shape with sidelobes as well as cross-polarisation levels better than -20 dB through a scan angle of 40°, have been realised. A study of the mutual coupling between two-layer as well as three-layer EMC circular patch elements has also been carried out for the useful range of interelement spacings. 3.Theoretical Analysis of Resonant Frequencies of Multilayer Patch Structures Theoretical investigations have been carried out on the resonance properties of single-layer and multilayer EMC patch structures employing the full-wave analysis based on spectral domain immittance approach. The impedance Green's functions for all these structures have been derived from the combination of equivalent transverse transmission lines concept Galerkin's method is employed in the spectral (Hankel) transform domain where two sets of disk current expansions are used for obtaining die characteristic equation. By solving the characteristic equation, the resonant frequencies are obtained for various values of the parameters of the layered antenna.

Il est bien connu dans la théorie de Maxwell que le rayonnement électromagnétique (EM) d'une onde porte à la fois du moment linéaire (énergie) et du moment angulaire. Ce dernier possède deux parties: le Moment Angulaire de Spin (ou SAM) qui est également connu sous le nom de la polarisation et le Moment Angulaire Orbital (ou OAM). Le SAM ne comprend que deux états (gauche et droite) et est utilisé en télécommunications pour doubler la capacité du canal. Par contre, le moment angulaire orbital (OAM) peut en théorie, avoir un nombre infini d'états appelés les modes OAM. Par conséquent, en radiofréquences, les premières applications de l'OAM ont été proposées dans le domaine des communications sans fil. Mais, tout d'abord, il est nécessaire de développer des antennes générant de telles ondes. L'objectif de cette thèse est de concevoir des antennes pour générer des ondes ayant un OAM. Le manuscrit se décompose en trois parties. Dans la première partie, un réseau d'antennes « patches » utilisant un déphaseur original est développé et testé. Ce réseau génère une onde ayant de l'OAM. Dans la deuxième partie, une cavité Fabry-Perot (FP) est utilisée pour apporter plus de directivité à ce réseau d'antennes. Enfin, la troisième partie consiste à générer des ondes guidées possédant du moment OAM. Ces ondes ont ensuite été utilisées pour exciter des antennes en cornet et rayonner des faisceaux directifs transportant du moment angulaire orbital. / It is well known from Maxwell’s theory that electromagnetic (EM) radiation carries both linear momentum (energy) and angular momentum. The latter has two parts: Spin Angular Momentum (SAM) which corresponds to the polarization of an EM wave and Orbital Angular Momentum (OAM) which is associated with the spatial distribution of an EM wave. The SAM has only two states (left and right) and is used to double the channel capacity in telecommunications. On the other hand, the OAM can theoretically have an infinite number of states called the OAM modes. Therefore, the first applications of OAM have been proposed in wireless communications at radio frequencies. However, first of all, it is necessary to develop the antennas for generating such waves. The objective of this thesis is to design the antennas for the generation of radio waves bearing OAM. The manuscript contains three parts. In the first part, an antenna using 4 patches and an original phase shifter is developed and tested to generate an OAM wave. In the second part, a Fabry-Perot (FP) cavity is used to enhance the directivity of this antenna. The third part is to generate guided OAM waves. Some horn antennas are used to radiate these waves with good directivity.

The ever increasing diversity in communication systems has created a demand for constant improvements in receiver components. This thesis describes the design and characterisation of front-end receiver components for various challenging applications, including characterisation of low noise foundry processes, LNA design and multi-band antenna design. It also includes a new theoretical analysis of noise coupling in low noise phased array receivers.In LNA design much depends on the choice of the optimum active devices. A comprehensive survey of the performance of low noise transistors is therefore extremely beneficial. To this end a comparison of the DC, small-signal and noise behaviours of 10 state-of-the-art GaAs and InP based pHEMT and mHEMT low noise processes has been carried out. Their suitability in LNA designs has been determined, with emphasis on the SKA project. This work is part of the first known detailed investigation of this kind. Results indicate the superiority of mature GaAs-based pHEMT processes, and highlight problems associated with the studied mHEMT processes. Two of the more promising processes have then been used to design C-band and UHF-band MMIC LNAs. A new theoretical analysis of coupled noise between antenna elements of a low noise phased array receiver has been carried out. Results of the noise wave analysis, based on fundamental principles of noisy networks, suggest that the coupled noise contribution to system noise temperatures should be smaller than had previously been suggested for systems like the SKA. The principles are applicable to any phased array receiver. Finally, a multi-band antenna has been designed and fabricated for a severe operating environment, covering the three extremely crowded frequency bands, the 2.1 GHz UMTS, the 2.4 GHz ISM and the 5.8 GHz ISM bands. Measurements have demonstrated excellent performance, exceeding that of equivalent commercial antennas aimed at similar applications.

This work deals with the most famous constructions of planar antennas. The work analyses selected methods of connecting planar antennas' charging with the possibility of impedance adaptation. An important part of the work consists of description of techniques for increasing bandwidth and conversely techniques for reducing the dimensions which are important for the design of planar antennas for mobile devices. The antennas were designed by means of theoretical basis and their properties were examined in the electromagnetic field simulator. The selected antenna model was constructed and its parameters were measured experimentally. The matching circuit for the antenna to tune it to different resonant frequencies was designed and constructed.

No description available.

Systems with extreme bandwidth are part of advanced modern systems at radio high capacitive communication. Originally this technology was intended for radar scan. Thanks to wide frequency band had radar possibility „ see" a behind crimp, e.g. behind woody partitions etc . To his noise immunity, fail safe tapping plus small wattage heftiness began use for datal systŽm function. If is elementary antenna compound from coaxial probe and shorting outlet, it is possible use to actuating separate narrow slot placed in the middle of incandescent dabs. Impedance and radiating characteristics conventionally plumbed phlobaphene antennae excited tape lead and suggested microstrip phlobaphene antennae are experimentally explored plus collated. Explored is so and effect changes slotted longitude slot on characteristics elementary antenna.

Radio Frequency (RF) energy transfer is getting increasingly importance in new generations of wireless sensor networks and this trend is tremendously supported by the modern trends to Internet of things (IoT). This promising technology enables proactive energy replenishment for wireless devices. With RF energy, transmission long distances between the energy source and the receiver can be overbridged. The main challenge thereby is the power conversion efficiency from a low level RF input power to a Direct Current (DC) voltage which is able to supply the mobile system. For this purpose, a novel approach for RF DC conversion is proposed. It consists of a modified voltage multiplier RF DC converter circuit by incorporating an inductor at the input of the circuit, which generates an induced voltage able to boost the output circuit and improve the conversion efficiency. Analytical analysis of the novel approach has been carried out to determine the optimal value of the inductor to maximize the output power. The experimental investigations show that the proposed solution is able to improve significantly both the output voltage and the power conversion efficiency, compared to the state of the art, and this especially at low input power ranges, which are often the case. At -10 dBm input power, the modified voltage multiplier RF DC converter circuit can reach 1.71 V output voltage and 49.21 % power conversion efficiency for, respectively, 500 kΩ and 10 kΩ resistive loads. In order to validate the new proposal for the RF transfer system experimentally, microstrip meander line antennas and microstrip patch antenna arrays are designed for different ISM bands, where relevant requirements for RF energy transfer are respected. For each antenna a modified voltage multiplier RF DC converter circuit has been applied and the system is tuned to the corresponding resonant frequency to avoid mismatching. In this investigation several scenarios have been addressed, such as RF transmission energy, RF energy harvesting in Global System for Mobile (GSM) bands and Wireless Local Area Networks (WLAN) band are developed. Field test results show high performances of experimental results in comparison to the state of the art.:1 Introduction 2 Theoretical Background 3 State of the Art of RF Energy Transfer 4 Novel Approach for a RF DC Converter Circuit 5 Antennas Design 6 Experimental Verification at Specific Scenarios 7 Conclusion / Die RF-Energieübertragung (RF) gewinnt in neuen Generationen von drahtlosen Sensornetzen zunehmend an Bedeutung. Dieser Trend wird durch das Internet der Dinge (IoT) weiter unterstützt. Diese vielversprechende Technologie ermöglicht eine proaktive Energieversorgung für drahtlose Geräte. Mit RF-Energie können große Entfernungen zwischen der Energiequelle und dem Empfänger überbrückt werden. Die größte Herausforderung dabei ist der Wirkungsgrad, mit dem von einer niedrigen HF-Eingangsleistung in eine Gleichspannung (DC), mit welcher das mobile System versorgt wird, gewandelt wird. Zu diesem Zweck wird ein neuer Ansatz für einen RF-DC-Wandler vorgeschlagen. Er besteht aus einer modifizierten Spannungsvervielfacher-RF-DC-Wandlerschaltung, die eine Spule am Eingang der Schaltung integriert. Diese erzeugt eine induzierte Spannung, die in der Lage ist die Ausgangsschaltung zu verstärken und den Umwandlungswirkungsgrad zu verbessern. Analytische Untersuchungen zu diesem neuartigen Ansatz wurden durchgeführt, um den optimalen Wert der Spule zu bestimmen und die Ausgangsleistung zu maximieren. Die experimentellen Untersuchungen zeigen, dass die vorgeschlagene Lösung in der Lage ist, sowohl die Ausgangsspannung als auch den Wirkungsgrad der Leistungsumwandlung im Vergleich zum Stand der Technik deutlich zu verbessern. Dies gilt besonders für niedrige Eingangsleistungsbereiche, welche häufig vorkommen. Bei -10 dBm Eingangsleistung kann die modifizierte Spannungsvervielfacher-RF-DC-Wandlerschaltung 1.71 V Ausgangsspannung und 49.21 % Leistungswandlungswirkungsgrad für jeweils 500 kΩ und 10 kΩ ohmsche Last erreichen. Um das neue RF-Übertragungssystem experimentell zu validieren, werden Mikrostreifenmäanderlinienantennen und Mikrostreifen-Patch-Antennenarrays für verschiedene ISM-Bänder ausgelegt, wobei die relevanten Anforderungen an die RF-Energieübertragung eingehalten werden. Für jede Antenne wurde eine modifizierte Spannungsvervielfacher-HF-DC-Wandlerschaltung verwendet und das System auf die entsprechende Resonanzfrequenz abgestimmt, um Fehlanpassungen zu vermeiden. Dabei wurden mehrere Szenarien untersucht, wie z.B. RF-Energieübertragung, RF-Energiegewinnung aus GSM-Bändern und WLAN-Netzwerken. Die Feldtests zeigen eine hohe Leistungsfähigkeit der experimentellen Ergebnisse im Vergleich zum Stand der Technik.:1 Introduction 2 Theoretical Background 3 State of the Art of RF Energy Transfer 4 Novel Approach for a RF DC Converter Circuit 5 Antennas Design 6 Experimental Verification at Specific Scenarios 7 Conclusion