[pt] O presente trabalho tem como objetivo analisar a utilização de barras constituídas por material compósito para atuarem como reforço de vigas de concreto submetidas à flexão. As barras analisadas são constituídas por polímero reforçado com fibras de carbono (PRFC), material este que apresenta comportamento linear elástico até a ruptura. Este material possui algumas vantagens em relação ao aço, como por exemplo, resistência à tração consideravelmente superior além de não ser suscetível ao fenômeno da corrosão ocasionada por intempéries ambientais. Durante o desenvolvimento do trabalho foi obtido um artigo o qual demonstra resultados de ensaios de laboratório nos quais os autores utilizaram vigas de concreto submetidas a ensaio de flexão por quatro pontos e reforçadas com barras de PRFC. Neste trabalho, o mesmo ensaio foi simulado no software Atena, programa este que realiza análise não linear para estruturas de concreto, considerando a fissuração deste material. Os resultados obtidos pelo software apresentaram consistência com os resultados registrados em laboratório pelos autores. Foi ainda analisada uma viga contínua de concreto submetida a um carregamento uniformemente distribuído. Essa viga foi reforçada com barras de mesmo diâmetro alterando-se apenas o material dessas barras (aço e PRFC). Dessa maneira, foi analisado o valor de carregamento que ocasiona a ruptura da viga. Foram constatadas duas importantes desvantagens das barras de PRFC em relação ao aço. A primeira desvantagem está no custo superior ao aço e por apresentar comportamento elástico até o rompimento, o PRFC não confere à estrutura de concreto uma ruptura dúctil. Os objetivos deste trabalho foram cumpridos e ao final são propostos novos estudos a serem realizados sobre o tema. / [en] The aim of the present work is to analyze the use of bars made of composite material to act as reinforcement for concrete beams subjected to bending. The analyzed bars are constituted by polymer reinforced with carbon fibers (PRFC), a material that presents linear elastic behavior until rupture. This material has some advantages in relation to steel, such as considerably higher tensile strength in addition to not being susceptible to the phenomenon of corrosion caused by environmental conditions. During the development of the work, an article was obtained which demonstrates results of laboratory tests in which the authors used concrete beams subjected to flexion testing by four points and reinforced with PRFC bars. In this work, the same test was simulated in the Atena software, a program that performs non-linear analysis for concrete structures, considering the cracking of this material. The results obtained by the software were consistent with the results recorded in the laboratory by the authors. It was also analyzed a continuous concrete beam subjected to a uniformly distributed load. This beam was reinforced with bars of the same diameter, changing only the material of these bars (steel and PRFC. In this way, the loading value that causes the beam to break when it is reinforced with steel bars and when it is reinforced with PRFC bars of the same diameter was analyzed. Two important disadvantages of PRFC bars in relation to steel have been noted. Due to its elastic behavior until breaking, this composite material does not give the concrete structure a ductile rupture. In addition, its cost is considerably higher than steel bars, since no suppliers of this type of reinforcement have been identified in Brazil, thus increasing the cost to purchase this product. The objectives of this work were accomplished and, in the end, new studies are proposed to be carried out on the theme.

[pt] Este trabalho tem como objetivo avaliar a resistência à força cortante de vigas de concreto reforçado com barras de fibras de vidro e investigar a contribuição dos diferentes mecanismos de transferência do esforço cortante para a resistência final da viga. Um programa experimental foi conduzido, incluindo ensaios para: caracterização do material, para avaliar o efeito de pino, para avaliar o engrenamento dos agregados e, por fim, ensaios de flexão de quatro pontos em vigas. Diferentes parâmetros foram investigados, como a quantidade de barras longitudinais para o efeito de pino, dimensão máxima do agregado graúdo para engrenamento dos agregados e a presença de estribos para os ensaios de vigas. O monitoramento do desenvolvimento da fissura crítica foi realizado com auxílio de correlação de imagem digital (digital image correlation, DIC, em inglês). Os resultados mostraram que não foi evidenciada diferença no comportamento de efeito de pino e de engrenamento dos agregados através dos ensaios realizados. Para os ensaios de vigas, observou-se que todos os espécimes apresentaram ruptura por tração da diagonal crítica e, para vigas sem estribos, a ação do efeito de pino pareceu contribuir significativamente para a resistência ao cisalhamento após a fissura, quando a carga diminui e as deflexões aumentam, resultado do menor engrenamento dos agregados à medida que a fissura se abre. Foi observado que a presença de estribos aumentou em até três vezes a resistência ao cortante das vigas ensaiadas e que houve ruptura do estribo na parte da dobra. / [en] This work aims to evaluate the shear strength of reinforced concrete beams with glass fiber reinforced polymer bars and to investigate qualitatively the contribution of the different shear transfer mechanisms to the final strength of the beam. An experimental program was conducted, including material characterization, dowel action tests, push-off tests, and finally, four-point bending tests on beams. Different parameters were investigated, such as the number of longitudinal bars for dowel action effect, maximum size of the coarse aggregate for aggregate interlock and the presence of stirrups for the beam tests. The monitoring of the development of the critical crack was performed with the aid of digital image correlation (DIC). The results showed that there was no difference in the behavior of the dowel action effect and the aggregate interlock through the tests performed. For beam tests, it was observed that all the specimens exhibited a concrete diagonal tension failure and for beams without stirrups, dowel action seemed to provide significant contribution to the shear strength after the crack, when the load reduces and the deflections increases, resulting from the loss of aggregate interlock as the crack opens. It was also observed that the presence of stirrups increased up to three times the shear strength of the beams tested and that there was rupture of the stirrup at the bent region.

This research aims to investigate the behaviour of glass fibre reinforced polymer bars (GFRP) reinforced continuous concrete deep beams. For this purpose, experimental, analytical and numerical studies were conducted. Nine continuous concrete deep beams reinforced with GFRP bars and one specimen reinforced with steel bars were experimentally tested to failure. The investigated parameters included shear span-to-overall depth ratio (𝑎/ℎ), size effect and web reinforcement ratio. Two 𝑎/ℎ ratios of 1.0 and 1.7 and three section heights of 300 mm, 600 mm and 800 mm as well as two web reinforcement ratios of 0% and 0.4% were used. The longitudinal reinforcement, compressive strength and beam width were kept constant at 1.2%, ≈55 MPa and 175 mm, respectively. The web reinforcement ratio achieved the minimum requirements of the CSA S806-12. The experimental results highlighted that the web reinforcement ratio improved the load capacities by about 10% and 18% for specimens having 𝑎/ℎ ratios of 1.0 and 1.7, respectively. For specimens with web reinforcement, the increase of 𝑎/ℎ ratio from 1.0 to 1.7 led to reductions in the load carrying capacity by about 33% and 29% for beams with overall depths of 300 mm and 600 mm, respectively. Additionally, a considerable reduction occurred in the shear strength due to the increase of the section depth from 300 mm to 600 mm. The experimental results confirmed the impacts of web reinforcement and size effect that were not considered by the strut-and-tie method (STM) of the only code provision, the Canadian S806-12, that addressed such elements. In this study, the STM was illustrated and simplified to be adopted for GFRP RC continuous deep beams, and then, the experimental results obtained from this study were employed to assess the performance of the effectiveness factors suggested by the STMs of the American (ACI 318-2014), European (EC2-04) and Canadian (S806-12) codes as well as those factors recommended by the previous studies to predict the load capacities. It was found that these methods were unable to reflect the influences of member size and/or web reinforcement reasonably, the impact of which has been confirmed by the current experimental investigation. Therefore, a new effectiveness factor was recommended to be used with the STM. Additionally, an upper bound analysis was developed to predict the load capacities of the tested specimens considering a reduced bond strength of GFRP bars after assessing the old version recommended for steel RC continuous deep beams. A good agreement between the predicted results and the measured ones was obtained with the mean and coefficient of variation values for experimental/calculated results of 1.02 and 5.9%, respectively, for the STM and 1.03 and 8.6%, respectively, for the upper-bound analysis. A 2D finite element analysis using ABAQUS/Explicit approach was carried out to introduce a model able to estimate the response of GFRP RC continuous deep beams. Based on the experimental results extracted from the pullout tests, the interface between the longitudinal reinforcement and concrete surface was modelled using a cohesive element (COH2D4) tool available in ABAQUS. Furthermore, a perfect bond between the longitudinal reinforcement and surrounding concrete was also modelled to evaluate the validity of this assumption introduced by many previous FE studies. To achieve a reasonable agreement with the test results, a sensitivity analysis was implemented to select the proper mesh size and concrete model variables. The suitability and capability of the developed FE model were demonstrated by comparing its predictions with the test results of beams tested experimentally. Model validation showed a reasonable agreement with the experiments in terms of the failure mode, total failure load and the load-deflection responses. The perfect bond model has overestimated the predicted results in terms of stiffness behaviour and failure load, while the cohesive element model was more suitable to reflect the behaviour of those specimens. The validated FE model was then employed to implement a parametric study for the key parameters that govern the behaviour of beams tested and to achieve an in depth understanding of such elements. The parametric study showed that the higher the 𝑎/ℎ ratio the more pronounced the effect of web and the longitudinal reinforcements and the lower the effect of concrete compressive strength; and vice versa when 𝑎/ℎ ratio reduces.

This master’s thesis was conducted at Linköping University in collaboration with ToyotaMaterial Handling in Mjölby to explore potential applications of recycled plastic in forklifttrucks. The primary objective was to identify the most suitable recycled plastic to be usedon the top cover of the BT Levio LWI160, which served as the focal point of this project.This was done in order to address the research questions: "What types of mechanical- andindustrial design requirements are affected when using recycled plastic (of various composi-tions), and to which new requirements and changes will result from this?" and "What are themajor mechanical- and industrial design challenges, advantages & disadvantages of switchingto recycled plastic material, considering economic and sustainability factors." The study concludes that the requirements of the top cover will largely remain unchanged.The use of PP 20GF necessitates further testing for structural integrity and quality con-sistency in recycled material. This material’s harder, less ductile nature may require newimpact testing and recycling processes. Industrial design benefits include simplified colourchoices due to the material’s transparent base hue, although the dark brown colour of re-cycled plastics limits options. Ensuring consistency across batches, minimising costs, andaddressing surface defects and purity issues are critical challenges. Despite uncertainties,switching to recycled plastic can reduce CO2 emissions by up to 24% and attract environ-mentally conscious customers

FRP stands for Fiber Reinforced Polymer. FRP materials have yet to be introduced inbridge construction in Sweden. Composite materials can through combined componentsand manufacturing processes be tailored to fit advanced bridge designs. FRP materials arestrong, durable and of low weight. FRP materials give the superstructure reduced weightand are therefore a suitable alternative for industrial prefabrication. This report shows thatFRP materials are possible to use in bridge construction. With the introduction of a specificEurocode we are confident that FRP materials will become a competitive alternative inbridge construction in Sweden in the future. / Broar är förenade med stora kostnader, dels för att bygga och dels för att underhålla ochreparera. FRP står för Fiber Reinforced Polymer är ett erkänt material för många andraanvändningsområden, exempelvis flyg och bilindustri. I Europa finns en mängd FRP-broar,men materialet har ännu inte introducerats i någon bro i Sverige.FRP är ett kompositmaterial som genom olika kombinationer av komponenter ochtillverkningsprocesser kan skräddarsys för den aktuella uppgiften i en konstruktion. FRPmaterialär starka, beständiga och har en låg vikt. Fördelar med FRP inom brokonstruktionär att det ger överbyggnaden en minskad egenvikt och därmed är ett lämpligt alternativ attprefabricera industriellt, då bland annat transport- och lyftbarhet gynnas samt att en högbeständighet ger minskat underhåll.Då ingen litteratur hanterar FRP i Brokonstruktion har de intervjuades åsikter varit mycketviktiga för arbetet. Litteraturstudien har legat till grund för en ökad förståelse för egenskaperutmärkande för olika typer av FRP. Intervjuer har utförts med personer som i dagslägetkommit i kontakt med materialet inom brokonstruktion. Detta har gjorts för att nå ett relevantresultat med möjlighet att kunna identifiera materialets för- respektive nackdelar samtanledningen till det låga användandet i Sverige.Rapporten visar att materialet har positiva egenskaper och är möjligt att använda vidkonstruktion av broar. Det saknas i dagsläget en specifik Eurokod som på ett enhetligt sättredovisar hur materialet ska hanteras. Med införandet av en specifik Eurokod och om en nykompetens arbetas fram inom branschen är vi övertygade om att FRP-material kommer attbli ett konkurrenskraftigt alternativ vid brokonstruktion.

Reinforced cement concrete (RCC) structures have become an important aspect in most of the buildings in our society around the world. Most of the multistoried reinforced concrete buildings house important institutions such as hospitals, schools, government establishments, defense establishments, business centers, sports stadiums, super markets and nuclear power plants. The cost of construction of such multistoried RCC structures is very high, and these structures need to be maintained and restored based on their functionality and importance using repair and retrofit strategies when these structures undergo damage. The steps involved in restoring RCC structures that have damages using repair / retrofit measures consists of identifying the source or cause of damage, assessment of the degree or extent of damage that has taken place using nondestructive techniques. Based on the assessment of degree of damage suitable repair / retrofit strategy using the appropriate repair material is applied to achieve the required load carrying capacity or strength. The present work involves assessing the efficacy of carbon fibre reinforced polymer (CFRP) based system applied on pre-damaged structural members to restore the member’s strength and stiffness through experimental investigations and finite element predictions. To validate the macrolevel properties of predamaged concrete micromechanical analysis, microscale studies and analytical investigations have been conducted. Plain and reinforced concrete test specimens: cylinders, square prisms and rectangular prisms having 25MPa and 35MPa cylinder compressive strengths pre-damaged due to mechanical (monotonic and cyclic loading) and thermal loading (exposure to different temperature and time durations) with applications of CFRP repair subjected to compression is investigated to study the behavior and enhancement in the compressive strength and stiffness after application of repair. Non destructive testing of thermally damaged concrete (exposed to different temperature and exposure time) is conducted using ultrasonic pulse velocity and tomography methods to understand the degradation in the strength and stiffness of thermally damaged concrete. The results of the non destructive testing helps in assessing the amount of repair that can be applied. To validate the macro scale behavior of thermally damaged concrete micro scale studies was performed adopting micro indentation, petrography, Raman spectroscopy, scanning electron miscroscopy (SEM) and Electron probe micro analysis (EPMA). During the event of a fire in RC structures which have been retrofitted. The high temperature caused due to fire tends to make the concrete to deteriorate and the repair material to delaminate. Loss of strength/ stiffness in concrete and delamination of the repair material in a retrofitted structural component in a structure causes instability which results in partial collapse or complete collapse of the structure. Thermal insulation of concrete and the repair material (CFRP) using geo-polymer mortar and simwool thermal fibre blanket exposed to high temperature and different exposure time are experimentally investigated. This is to evaluate the effectiveness of the thermal insulation in protecting epoxy based structural repair material(CFRP) from thermal damage and to minimize the delamination of the repair material when exposed to high temperatures. Slender columns when loaded eccentrically fail at a load much lesser than their actual load carrying capacity. In RC buildings where additional floors need to be added, in those situations slender columns which are already eccentrically loaded tend to get damaged or fail due to additional load which act on them. Therefore to restore such columns experimental and finite element investigations on reinforced concrete slender columns having 25MPa cylinder compressive strength subjected to eccentric monotonic compressive loading with applications of CFRP repair is studied to understand the behavior and the enhancement in load carrying capacity after application of repair. Experimental investigations are conducted to study fracture and fatigue properties of thermally damaged concrete geometrically similar notched plain and reinforced concrete beams having 25MPa cylinder compressive strength exposed to different combinations of temperature and durations with application of repair (CFRP). Nonlinear fracture parameters of thermally damaged concrete is computed which help in understanding the fracture behavior of thermally damaged concrete and application of repair. Effectiveness of CFRP repair and failure behaviour of these beams are studied when these thermally damaged notch concrete beams are subjected to monotonic and cyclic (fatigue) loading. Reinforced concrete slender beams when subjected to unexpected loads such as earthquakes get damaged. The increase in load carrying capacity and fatigue life of reinforced concrete slender beams having 25MPa cylinder compressive strength in flexure subjected to monotonic and cyclic loading with applications of CFRP repair is investigated using experimental and finite element investigations. Finite element analysis of concrete specimens pre-damaged due to mechanical (monotonic and cyclic loading) / thermal loading (exposure to different temperature and time durations) with applications of CFRP repair and assessment of amount of repair required is investigated. Analytical (empirical) models are developed to assess the mechanical properties of concrete (elastic moduli, compressive strength and split tensile strength) exposed to different temperatures and time durations. Nonlinear fracture parameters of geometrically similar plain concrete notch beams exposed to different temperature and time durations are determined. Fracture parameters (stress intensity factor) of thermally damaged plain and reinforced concrete notched beams with application of CFRP have been determined. Effect of size and shape of thermally damaged plain concrete compression members with application of CFRP wrap have been studied. Crack mouth opening displacements (CMOD), strains and crack lengths of thermally damaged plain concrete (PC) notched beams using digital image correlation has also been determined.

The search and research for high performance materials for aerospace applications is a continuous evolving process. Among several fibre reinforced polymers, carbon fibre reinforced polymer (CFRP) is well known for its high specific stiffness and strength. Though high modulus and high strength carbon fibre with structural resin systems have currently been established reasonably well and are catering to a wide variety of aerospace structural applications, these properties are generally directional with very high properties along the fibre direction dominated by fibres and low in other directions depending mainly on the resin properties. Thus, there is a need to enhance the mechanical properties of the resin systems for better load transfer and to improve the resin dominated properties like shear strength and properties in directions other than along the fibre. Use of carbon nanotubes (CNTs) with their extraordinary specific stiffness and strength apparently has great potential as an additional reinforcement in resin for development of CNT-CFRP nanocomposites. However, there are several issues that need to be addressed such as compatibility of a particular resin with CNTs, amount of CNTs that can be added, uniform dispersion of these nanotubes, surface treatment and curing process etc., for optimal enhancement of the required properties. Epoxy and cyanate ester resin systems are finding applications in aerospace structures owing to their desirable set of properties. Of these, bisphenol E cyanate ester (BECy) resin of low viscosity with its low moisture absorption, better dimensional stability, and superior mechanical properties can establish itself as potential structural resin system for these applications. BECy in particular has the advantage of being more suitable for out of autoclave manufacturing process such as Vacuum Assisted Resin Transfer Molding (VARTM). Literature shows that, significant work has been carried out by various researchers reporting improvements using CNTs in epoxy resins along with various associated problems. However, studies on effects of addition of CNTs /fCNTs to BECy-CFRP composite system are not well reported. Thus, objective of this work is to study the effects of adding pristine and functionalized CNTs to low viscosity cyanate ester as well as epoxy resin systems. Further, to study the effects on mechanical properties of nanocomposites with carbon fibre reinforcement in these CNT dispersed resin system through a combination of experimental and computational approaches. Multiwall carbon nanotubes (CNTs) without and with different chemical functionalization are chosen to be added to epoxy and BECy resins. The quantity of these CNTs /fCNTs is varied in steps up to 1% by weight. Different methods of mixing such as shear mixing, ultrasonication and combined mixing cycles are implemented to achieve uniform dispersion of these nanotubes in the resin system. Standard test samples are prepared from these mixtures of nanotubes in resin systems to study the variation in mechanical properties. Further, these nanotubes added resin systems are used in fabricating CFRP laminates by VARTM process. Both uni-directional and bi-directional laminates are made with the above modified resin systems with CNTs/fCNTs. Series of experimental investigations are carried out to study various aspects involved in making of nanocomposites and the effects of the same on different mechanical properties of the nanocomposites. Standard specimens are cut out from these laminates to evaluate them for tension, compression, flexure, shear and interlaminar shear strength. The main parameters investigated are the effects of varied quantity of CNTs and functionalized CNTs in the resin mix and in CFRP nanocomposites, effect of different mixing / curing cycles etc. on the mechanical properties of the nanocomposites. The investigations have yielded very interesting and encouraging results to arrive at optimum quantity of CNTs to be added and also the effects of functionalization to achieve enhanced mechanical properties. In addition, correlation of mechanical property enhancements with failure mechanisms, dispersion behaviour and participation of CNTs / fCNTs in load transfer are explained with the aid of scanning electron microscope images. Computational studies are carried out through atomistic models using computational tools to estimate the mechanical properties, understand and validate the effects of various parameters studied through series of experimental investigations. An atomistic model is built taking into consideration the nanoscale effects of the single wall carbon nanotubes (SWCNTs) and its reinforcement in the BECy resin. Using these atomistic models, mechanical properties of individual SWCNT, BECy polymer resin, polymer with different quantities of added SWCNT, and the CFRP laminates with improved resin are computed. As the interaction of CNT with the polymer is only at the outermost layer and the mechanical properties of either MWCNTs or SWCNTs are too high compared to resin systems, it is not expected to have any difference in the final outcome whether it is MWCNT or SWCNT. Hence, only SWCNTs are considered in computational studies as it helps in reducing the complexity of atomistic models and computational time when coupled with polymer resin. This is valid even for functionalized CNT as functionalization is also a surface phenomenon. To start with, the mechanical behaviour of SWCNT is studied using molecular mechanics approach. Molecular mechanics based finite element analysis is adopted to evaluate the mechanical properties of armchair, zigzag and chiral SWCNT of different diameters. Three different types of atomic bonds, i.e., carbon-carbon covalent bond and two types of carbon-carbon van der Waals bonds are considered in the carbon nanotube system. The stiffness values of these bonds are calculated using the molecular potentials, namely Morse potential function and Lennard-Jones interaction potential function respectively and these stiffness values are assigned to spring elements in the finite element model of the SWCNT. The importance of inclusion of Lennard-Jones interactions is highlighted in this study. Effect of these non-bonded interactions is studied by making the numerical stiffness of these bonds to negligible levels and found that they significantly reduce the mechanical properties. The effect of non-bonded Lennard-Jones atomic interactions (van der Waal interactions) considered here is a novelty in this work which has not been considered in previous research works. The finite element model of the SWCNT is constructed, appropriate boundary conditions are applied and the behaviour of mechanical properties of SWCNT is studied. It is found that the longitudinal tensile strength and maximum tensile strain of armchair SWCNTs is greater than that of zigzag and chiral SWCNTs and its value increases with increasing SWCNT diameter. The estimated values of the mechanical properties obtained agree well with the published literature data determined using other techniques. As the systems become more complicated with the inclusion of polymers, molecular dynamics (MD) method using well established codes is more adoptable to study the effect of SWCNTs on BECy. Hence, it is used to model and solve the nanosystems to generate their stress-strain behavior. Further, MD approach followed here can effectively include interfacial interaction between polymer and the CNTs as well. Mechanical properties of SWCNT functionalized SWCNT (fSWCNT), pure BECy resin and that of the CNT nanocomposite consisting of specific quantity of SWCNT / fSWCNT in BECy are estimated using MD method. Atomistic models of SWCNT, fSWCNT, BECy, BECy with specific quantities of CNT / fSWCNT are constructed. A monomer of BECy is modelled and stabilized before its usage as a building block for modelling of BECy resin and to compute its properties. A cell of specific size containing monomers of BECy and another cell of same size with SWCNT at centre surrounded by BECy monomer molecules are built. The appropriate quantity of SWCNT in resin is modelled. This model captures the required density of the composite resin. The models so constructed are subjected to geometric optimization satisfying the convergence criteria and equilibrated through molecular dynamics to obtain a stable structure. The minimized structure is subjected to small strain in different directions to calculate the Young’s modulus and other moduli of the CNT-BECy resin composite. The process is repeated for different quantities of SWCNT in BECy resin to obtain their moduli. Further, tensile and shear strengths of CNT-BECy are obtained by subjecting the equilibrated structure to a series of applied strains from 0 to 10% in steps of 1%. The stress values corresponding to each strain are obtained and a stress – strain curve is plotted. From the stress- strain curve, the strengths of the CNT -BECy which is the stress corresponding to the modulus after which the material starts to soften are determined. Effects of functionalization on mechanical properties of SWCNT are observed. Further, effects of functionalization of SWCNT are studied with a specific quantity of fSWCNT on different moduli and strengths of BECy are investigated. The properties of enhanced CNT–BECy nanocomposite resin with different quantities of added CNT obtained through MD are used to estimate the mechanical properties of the CNT-BECy-CFRP nanocomposite using micromechanics model. Further, validation with experimental results is attempted comparing the trends in enhancement of properties of the CNT-BECy resin and CNT-BECy-CFRP nanocomposite system. The outcome of this research work has been significantly positive in terms of i) Development of an appropriate process establishing different parameters for dispersing CNTs in the resin system, mixing, curing cycle for making of nanocomposites demonstrating significant and consistent enhancement of mechanical properties of BECy based resin system and CFRP nanocomposites using optimum quantity of CNTs /fCNTs through a series of well planned and executed experimental investigations. Evaluation of mechanical properties for each of the cases has been carried out experimentally. ii) Establishing a computational methodology involving intricate atomistic modelling and molecular dynamics of nanosystems for estimation of mechanical properties of BECy polymer resin and to study the effects by addition of SWCNT / functionalized SWCNT on the properties. Results obtained through series of experimental investigations have been validated through this computational study. This could be an important step towards realising the potential of this resin system for high performance aerospace applications. Thus, in brief, detailed experimental work combined with computational studies performed as presented in this thesis resulted in achieving structurally efficient cyanate ester based nanocomposites which is unique and not reported in open literature.

This diploma thesis deals with the design of FRP reinforced concrete structures. The theoretical part is focused mainly on the punching shear of a flat two way slab according to ACI, fib Bulletin, CSA, and JSCE standards. This thesis also includes a description of the punching shear resistance according to Eurocode 2. FRP reinforcement, its mechanical properties, and their behaviour in time are also described. Next, a parametric study was performed that examines the effects of various parameters on the punching shear resistance according to the standards mentioned above. At the end a non-linear analysis using the ATENA software was performed. The practical part includes a structural design of a flat two way slab. The slab uses a steel reinforcement at the bottom, while the top is reinforced with FRP reinforcement. The punching shear design is also included. In the last chapter the serviceability limit state is checked, specifically the slab long-term deflection. The thesis also includes drawings. All calculations were performed in accordance with Eurocode 2 and fib Bulletin No. 40.

Les enquêtes récentes sur les séismes ont fait ressortir l'importance des murs en béton armé en tant que partie intégrante des structures. L’évolution des règlements prend en compte ces considérations, par contre le bâti existant doit subir des renforcements dans l’objectif de leur mise en conformité. Dans cette thèse une étude expérimentale faite sur douze murs (six élancés et six courts) renforcés par un collage externe en composite a été conduite. Les murs ont été conçus en étant sous-renforcés à la flexion et cisaillement. Quatre de ces six échantillons ont été renforcés par des bandes de PRFC collées. Deux spécimens, un témoin et un renforcé, ont été soumis à un test de chargement statique et quatre échantillons, l'un témoin et trois rénovés, ont été soumis à des essais de charge cyclique. La discussion et l’analyse des tests incluent la description de la fissuration, l’analyse de la rigidité, de la capacité de charge ultime, de la ductilité. / Recent earthquake surveys have revealed the significance of RC walls as an integral part of structures. It reduces the structure damage to some extent. However, like other structural member they too are vulnerable. Researchers on basis of their post eartthquake survey and laboratary experiments have concluded that the RC wall buildings sustained damage, mainly due to design and construction work flaws. In this thesis experimental result of shear walls is discussed. They were designed under-reinforced to fail in shear in ase of short wall and in flexure for slender walls. Three out of these six specimens, in each case, were strengthened externally with CFRP strips bonded to wall panel and mesh anchors installed at wall foundation joint. Two specimens, one RC and one CFRP retrofitted (short and slender wall each), were subjected to static load test and three specimens, one RC and two to three CFRP retrofitted, were subjected to quasi static cyclic load tests. The test result analysis discussion includes failure mode, stiffness, ultimate load capacity, ductility, and energy dissipation.