In this study, a novel and systematic methodology for the design and optimization of lowpass filters (LPFs), and multiorder-bandpass filters (BPFs) are proposed. The width of the LPF signal traces consistently follow Fourier truncated series, and the thickness of the substrate as well. By studying different lengths and other physical constraints, the design meets predefined electrical requirements. Moreover, superformula is used in split ring resonators (SRRs) designs to obtain a BPF response and significant structural compactness. Non-uniform transmission lines, as well as superformula equations, are programmed in MATLAB, which is also used for analytical validations. Traces are drawn in AutoCAD. The substrate of LPF is constructed in Pro/e. Finally, the optimized layouts are imported to Ansys High Frequency Structure Simulation (HFSS) software for simulation and verification. Nonuniform LPFs are optimized over a range of 0-6 GHz with cutoff frequency 3.5 GHz. Superformula implemented multiorder-BPFs are optimized with cutoff frequency of 1.1 GHz.

No description available.

<div>Atoms trapped in close proximity to optical resonators provides a powerful tool for exploring atom light interactions and their quantum applications. In this work I will describe the development of a neutral atom quantum simulator that implements trapped cesium atoms which have been localized via optical tweezers in close proximity to the surface of a micro-ring resonator fabricated on the surface of an optical chip. The small separation between the cavity and the atom allows for relatively large atom photon coupling strength g on the order of a few hundred MHz. Coupling multiple atoms to a common nanophotonic mode provides a channel through which atoms can exchange virtual photons for the study of long range spin exchange and other quantum many body models.</div><div></div><div>This platform has proven to be extremely versatile. We have thus far successfully demonstrated our ability to trap and image individual atoms directly above the surface of our photonic chips as well as the ability to extend trapping and imaging to arrays of tweezer traps which can be loaded with one or more atoms with high probability. Due to the simplified fabrication process of our planar geometry photonic chips we have been able to rapidly prototype and evolve our system to facilitate new and improved methods of trapping atoms near the surface of our nanophotonic structure. In the following I will discuss the development of our apparatus, our current progress observing signatures of atom-cavity coupling, and some of our future goals we are approaching.</div>

Bends and splitters are typically the fundamental limiting waveguide components in reducing the size of planar lightwave circuits (PLCs) based on waveguides that have a low core/clad refractive index contrast, such as silicon-on-insulator (SOI) rib waveguides. This dissertation presents a solution to this problem in the form of trench-based bends (TBBs) and trench-based splitters (TBSs). Emphasis is placed on experimental demonstration of these components and their integration into practical devices exhibiting significant size reduction. First, a compact and low loss silicon-on-insulator rib waveguide 90◦ TBB is demonstrated based on an etched vertical interface and total internal reflection (TIR) realized by a trench filled with SU8. The measured loss for TE polarization is 0.32 dB ± 0.02 dB/bend at a wavelength of 1.55 μm, which is the best reported in literature. Next, 90◦ TBSs are reported in which each splitter occupies an area of only 11 μm x 11 μm. These components require fabrication of trenches with a nearly 10:1 aspect ratio. A variety of single TBSs are fabricated having different trench widths. The relative amount of power directed into the transmission and reflection arms of the splitters is measured. The TBS reflection and transmission ratio agrees with three dimensional (3D) finite difference time domain (FDTD) predictions. An 82 nm wide trench filled with index matching fluid is experimentally shown to have a reflection/transmission splitting ratio of 49/51 at a wavelength of 1550 nm. To increase the fabrication yield of TBSs, the splitter angle is modified from 90◦ to 105◦, which permits the trench width to be increased to 116 nm for a 50/50 splitter using SU8 as the trench fill material. The fabrication and measurement of compact 105◦ TBBs and TBSs are reported followed by their integration into 1 x 4, 1 x 8, and 1 x 32 trench-based splitter networks (TBSNs). The measured total optical loss of the 1 x 32 TBSN is 9.15 dB. Its size is only 700 μm x 1600 μm for an output waveguide spacing of 50 μm. Finally, a compact SOI trench-based ring resonator (TBRR) composed of 90◦ TBBs, TBSs, and rib waveguides is demonstrated. A TBRR with a ring circumference of 50 μm occupies an area of 20 x 20 μm. The free spectral range (FSR) is as large as 14 nm. By changing the trench fill material from SU8 (n = 1.57) to index fluid (n = 1.733), the peak wavelength can be shifted ∼2 nm. Fabricated TBSNs and TBRRs demonstrate that large size reductions are possible for devices based on TBBs and TBSs. The net result is bend and splitter configurations with a size that is essentially independent of core/clad refractive index contrast. The approach developed in this dissertation is applicable to a wide range of waveguide material systems that have small core/clad refractive index contrast.

Yes / This article presents a miniaturized triple-band antenna for Internet of Things (IoT) applications. The miniaturization is achieved by using a split square ring resonator and half ring resonator. The antenna is fabricated on an FR4 substrate with dimensions of (33 × 22 × 1.6) mm3. The proposed antenna resonates at the frequencies 2.4 GHz, 3.7 GHz, and 5.8 GHz for WLAN and WiMax applications. The obtained −10 dB bandwidth for the three bands of the proposed antenna are 300 MHz, 360 MHz, and 900 MHz, respectively. The measured reflection coefficient values of the proposed antenna corresponding to each resonant frequency are equal to −14.772 dB, −20.971 dB, and −28.1755 dB, respectively. The measured gain values are 1.43 dBi, 0.89 dBi, and 1 dBi, respectively, at each resonant frequency. There is a good agreement between the measured and simulated results, and both show an omnidirectional radiation pattern at each of the antenna resonant frequencies that is suitable for IoT portable devices.

付記する学位プログラム名: 京都大学卓越大学院プログラム「先端光・電子デバイス創成学」 / 京都大学 / 新制・課程博士 / 博士(工学) / 甲第23904号 / 工博第4991号 / 新制||工||1779(附属図書館) / 京都大学大学院工学研究科電子工学専攻 / (主査)教授 竹内 繁樹, 教授 川上 養一, 准教授 浅野 卓 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DGAM

The ever-increasing bandwidth requirements to support telecommunications infrastructure necessitates large-scale fabrication of low-cost and scalable silicon photonic integrated circuits. Wavelength-division multiplexing (WDM) schemes are fundamentally limited in the number of channels supported in long-haul transmission by the erbium doped fiber amplifier (EDFA). To address this, researchers have turned focus toward the thulium doped fiber amplifier (TDFA), which provides 3× more bandwidth. This thesis describes the development of high-speed silicon-on-insulator (SOI) micro-ring resonator (MRR) modulators optimized for wavelengths in the TDFA band. Chapter 2 presents a theoretical performance comparison between MRR modulators designed for optimized use at EDFA and TDFA wavelengths. Chapter 3 presents an experimental study of optical loss mechanisms at extended wavelengths which suggests reduced waveguide scattering and enhanced divacancy defect absorption as well as larger bending and substrate leakage losses when compared with shorter wavelengths. An electronic variable optical attenuator is characterized in Chapter 4 to experimentally verify the predicted 1.7× TDFA-band free-carrier effect enhancement over EDFA-band wavelengths. The first steady-state operation of an MMR modulator near a central wavelength of 1.97 µm is also demonstrated under the enhanced free-carrier effect. Chapter 5 demonstrates the first high-speed reverse bias operation of an MRR modulator with a measured bandwidth of 12.5 GHz, and an on-chip optical link consisting of a modulator followed by a defectmediated detector with open eye-diagrams up to data rates of 12.5 Gbps. Chapter 6 introduces an electrically-driven post-fabrication defect-assisted resonance trimming technique via local annealing for use in MRR devices. Chapter 7 presents a Monte Carlo simulation of resonance alignment in multi-MRR systems subjected to spatially-correlated wafer variation created through the Virtual Wafer Model process to predict thermal power consumption and power reduction through resonance trimming. / Thesis / Doctor of Philosophy (PhD)

Yes / In this paper, we present the design of a compact and highly sensitive microwave sensor based on a metamaterial complementary split-ring resonator (CSRR), for liquid characterization at microwave frequencies. The design consists of a two-port microstrip-fed rectangular patch resonating structure printed on a 20 × 28 mm2 Roger RO3035 substrate with a thickness of 0.75 mm, a relative permittivity of 3.5, and a loss tangent of 0.0015. A CSRR is etched on the ground plane for the purpose of sensor miniaturization. The investigated liquid sample is put in a capillary glass tube lying parallel to the surface of the sensor. The parallel placement of the liquid test tube makes the design twice as efficient as a normal one in terms of sensitivity and Q factor. By bending the proposed structure, further enhancements of the sensor design can be obtained. These changes result in a shift in the resonant frequency and Q factor of the sensor. Hence, we could improve the sensitivity 10-fold compared to the flat structure. Subsequently, two configurations of sensors were designed and tested using CST simulation software, validated using HFSS simulation software, and compared to structures available in the literature, obtaining good agreement. A prototype of the flat configuration was fabricated and experimentally tested. Simulation results were found to be in good agreement with the experiments. The proposed devices exhibit the advantage of exploring multiple rapid and easy measurements using different test tubes, making the measurement faster, easier, and more cost-effective; therefore, the proposed high-sensitivity sensors are ideal candidates for various sensing applications. / This work was supported by the Moore4Medical project, funded within ECSEL JU in collaboration with the EU H2020 Framework Programme (H2020/2014–2020) under grant agreement H2020-ECSEL-2019-IA-876190, and the Fundação para a Ciência e Tecnologia (ECSEL/0006/2019). This project received funding in part from the DGRSDT (Direction Générale de la Recherche Scientifique et du Développement Technologique), MESRS (Ministry of Higher Education and Scientific Research), Algeria. This work was also supported by the General Directorate of Scientific Research and Technological Development (DGRSDT)–Ministry of Higher Education and Scientific Research (MESRS), Algeria, and funded by the FCT/MEC through national funds and, when applicable, co-financed by the ERDF, under the PT2020 Partnership Agreement under the UID/EEA/50008/2020 project.

Photonic bandgap structures have provided promising platform for miniaturization of modern integrated optical devices. In this thesis, a photonic crystal based ring resonator (PCRR) is proposed and optimized to exhibit high quality factor. Also, force sensing application of the optimized PC ring resonator and Dense Wavelength Division Multiplexing (DWDM) application of the PCRR are discussed. Finally fabrication and characterization of the PCRR is presented. A photonic crystal ring resonator is designed in a hexagonal lattice of air holes on a silicon slab. A novel approach is used to optimize PCRR to achieve high quality factor. The numerical analysis of the optimized photonic crystal ring resonator is presented in detail. For all electromagnetic computations Finite Difference Time Domain (FDTD) method is used. The improvement in Q factor is explained by using the physical phenomenon, multipole cancellation of the radiation held of the PCRR cavity. The corresponding mathematical frame work has been included. The forced cancellation of lower order radiation components are verified by plotting far held radiation pattern of the PCRR cavity. Then, the force sensing application of the optimized PCRR is presented. A high sensitive force sensor based on photonic crystal ring resonator integrated with silicon micro cantilever is presented. The design and modelling of the device, including the mechanics of the cantilever, FEM (Finite Element Method) analysis of the cantilever beam with PC and without PC integrated on it. The force sensing characteristics are presented for forces in the range of 0 to 1 N. For forces which are in the range of few tens of N, a force sensor with bilayer cantilever is considered. PC ring resonator on the bilayer of 220nm thick silicon and 600nm thick SiO2 plays the role of sensing element. Force sensing characteristics of the bilayer cantilever for forces in the range of 0 to 10 N are presented. Fabrication and characterization of PCRR is also carried out. This experimental work is done mainly to understand practical issues in study of photonic crystal ring resonators. It is proved that Q factor of PCRR can be signi cantly improved by varying the PCRR parameters by the proposed method. Dense Wavelength Division Multiplexing (DWDM) application of PC ring resonator is included. A novel 4-channel PC based demultiplexer is proposed and optimized in order to tolerate the fabrication errors and exhibit optimal cross talk, coupling efficiency between resonator and various channels of the device. Since the intention of this design is, to achieve the device performance that is independent of the unavoidable fabrication errors, the tolerance studies are made on the performance of the device towards the fabrication errors in the dimension of various related parameters. In conclusion we summarize major results, applications including computations and practical measurements of this work and suggest future work that may be carried out later.

In this dissertation I present results on our efforts to increase the sensitivity and selectivity of silicon nanowire ion-sensitive field-effect transistors for the detection of biomarkers, as well as a novel method for wireless power transfer based on metamaterial rectennas for their potential use as implantable sensors. The sensing scheme is based on changes in the conductance of the semiconducting nanowires upon binding of charged entities to the surface, which induces a field-effect. Monitoring the differential conductance thus provides information of the selective binding of biological molecules of interest to previously covalently linked counterparts on the nanowire surface. In order to improve on the performance of the nanowire sensing, we devised and fabricated a nanowire Wheatstone bridge, which allows canceling out of signal drift due to thermal fluctuations and dynamics of fluid flow. We showed that balancing the bridge significantly improves the signal-to-noise ratio. Further, we demonstrated the sensing of novel melanoma biomarker TROY at clinically relevant concentrations and distinguished it from nonspecific binding by comparing the reaction kinetics. For increased sensitivity, an amplification method was employed using an enzyme which catalyzes a signal-generating reaction by changing the redox potential of a redox pair. In addition, we investigated the electric double layer, which forms around charges in an electrolytic solution. It causes electrostatic screening of the proteins of interest, which puts a fundamental limitation on the biomarker detection in solutions with high salt concentrations, such as blood. We solved the coupled Nernst-Planck and Poisson equations for the electrolyte under influence of an oscillating electric field and discovered oscillations of the counterion concentration at a characteristic frequency. In addition to exploring different methods for improved sensing capabilities, we studied an innovative method to supply power to implantable biosensors wirelessly, eliminating the need for batteries. A metamaterial split ring resonator is integrated with a rectifying circuit for efficient conversion of microwave radiation to direct electrical power. We studied the near-field behavior of this rectenna with respect to distance, polarization, power, and frequency. Using a 100 mW microwave power source, we demonstrated operating a simple silicon nanowire pH sensor with light indicator.