Spelling suggestions: "subject:"softswitching"" "subject:"hostswitching""
91 |
Theoretical Analysis and Design for the Series-Resonator Buck ConverterTu, Cong 03 February 2023 (has links)
High step-down dc/dc converters are widely adopted in a variety of areas such as industrial, automotive, and telecommunication. The 48 V power delivery system becomes increasingly popular for powering high-current and low-voltage chips. The Series-Capacitor Buck (SCB) converter doubles the duty ratio and equalizes the current between the two phases. Hard switching has hindered efforts to reduce volume via increased switching frequency, although a monolithically integrated SCB converter has boosted current density. A Series-Resonator Buck (SRB) converter is realized by adding a resonant tank in series with the series capacitor Cs. All switches turn on at zero-voltage (ZVOn), and the low-side switches turn off at zero-current (ZCOff). The design of the SRB converter includes characterizing the design variables' impacts on the converter performances and designing low-loss resonant components as the series resonator.
The Series-Resonator Buck converter belongs to the class of quasi-resonant converters. Its resonant frequency is higher than the switching frequency, and its waveforms are quasi-sinusoidal. This work develops a steady-state model of the SRB converter to calculate voltage gain, component peak voltages, and resonant inductor peak current. Each switching cycle is modeled based on the concept of generalized state-space averaging. The soft-switching condition of the high-side switches is derived. The ZVS condition depends on the normalized control variable and the load condition. The gain equation models the load-dependent characteristic and the peak gain boundary. The theoretical peak voltage gain of the SRB converter is smaller than the maximum gain of the SCB converter. A smaller normalized load condition results in a larger peak voltage gain of the SRB converter.
The large-signal model of the SRB converter characterizes the low-frequency behavior of the low-pass filters with the series capacitor and the high-frequency behavior of the resonant elements. A design recommendation of t_off f_r<0.5 is suggested to avoid the oscillation between the series capacitor Cs and the output inductors Lo. In other words, the off-duration of the low-side switches is less than half of 1/fr, and therefore the negative damping effect from the parallel resonant tank to the vCs response is reduced. The transfer functions of the SRB converter are presented and compared with those of the SCB converter. The series resonator brings in an extra damping effect to the response of output capacitor voltage.
The understanding of the analytical relationships among the resonant tank energy, voltage gain, and component stresses was utilized to guide the converter design of the converter's parameters. A normalized load condition at √2 minimizes the stresses of the series resonator by balancing the peak energy in the resonant elements Lr and Cr. The f_s variation with voltage gain M is less than 10%. The non-resonant components C_s, L_oa, and L_ob are designed according to the specified switching ripples.
The ac winding loss complicates the winding design of a resonant inductor. This work replaces the rectangular window with a rhombic window to reduce the eddy current loss caused by the fringing effect. The window ratio k_y is added as a design variable. The impacts of the design variables on the inductance, core loss, and winding loss are discussed. The air-gap length l_g is designed to control the inductance. A larger k_y design results in a short inductor length l_c and a smaller winding loss. The disadvantages include a smaller energy density design and a larger core loss due to the smaller cross-sectional area. In the design example presented in the thesis, the presence of the rhombic shape increases the gap-to-winding distance by two times, and also reduces the y-component of the magnetic field by a factor of two. The total inductor loss is reduced by 56% compared to a conventional design with a rectangular winding window while keeping the same inductance and the same inductor volume.
This dissertation implements a resonator, replacing the series capacitor, in an SCB converter. The resultant SRB converter shows a 30% reduction in loss and a 50% increase in power density. The root cause of the divergence issue is identified by modeling the negative damping effect caused by resonant elements. The presented transient design guideline clears the barriers to closed-loop regulation and commercialization of the SRB converter. This work also reshapes winding windows from rectangle to rhombus which is a low-cost change that reduces magnetic loss by half. The theoretical analysis and design procedures are demonstrated in a 200 W prototype with 7% peak efficiency increase compared to the commonly used 30 W commercial SCB product. / Doctor of Philosophy / High step-down dc/dc converters are widely adopted in a variety of areas such as industrial, automotive, and telecommunication areas. The 48 V power delivery system becomes increasingly popular for powering high-current and low-voltage chips. The Series-Capacitor Buck (SCB) converter doubles the duty ratio and equalizes the current between the two phases. Hard switching has hindered efforts to reduce volume via increased switching frequency although a monolithically integrated SCB converter has boosted current density. A Series-Resonator Buck (SRB) converter is realized by adding a resonant tank in series with the series capacitor Cs. All switches turn on at zero-voltage (ZVOn), and the low-side switches turn off at zero-current (ZCOff). The challenges to designing the SRB converter include characterizing the design variables' impacts on the converter performances and designing low-loss resonant components as the series resonator.
The resultant SRB converter shows a 30% reduction in loss and a 50% increase in power density. The root cause of the divergence issue is identified by modeling the negative damping effect caused by the resonant elements. The presented transient design guideline clears the barriers of closed-loop regulation and commercialization of the SRB converter. This work also reshapes winding windows from rectangle to rhombus, which is a low-cost change that reduces magnetic loss by half. The theoretical analysis and design procedures are demonstrated in a 200 W prototype with 7% peak efficiency increase compared to the commonly used 30 W commercial SCB product.
|
92 |
Flexibility in MLVR-VSC back-to-back linkTan, Jiak-San January 2006 (has links)
This thesis describes the flexible voltage control of a multi-level-voltage-reinjection voltage source converter. The main purposes are to achieve reactive power generation flexibility when applied for HVdc transmission systems, reduce dynamic voltage balancing for direct series connected switches and an improvement of high power converter efficiency and reliability. Waveform shapes and the impact on ac harmonics caused by the modulation process are studied in detail. A configuration is proposed embracing concepts of multi level, soft-switching and harmonic cancellation. For the configuration, the firing sequence, waveform analysis, steady-state and dynamic performances and close-loop control strategies are presented. In order not to severely compromise the original advantages of the converter, the modulated waveforms are proposed based on the restrictions imposed mathematically by the harmonic cancellation concept and practically by the synthesis circuit complexity and high switching losses. The harmonic impact on the ac power system prompted by the modulation process is studied from idealistic and practical aspects. The circuit topology being proposed in this thesis is developed from a 12-pulse bridge and a converter used classically for inverting power from separated dc sources. Switching functions are deduced and current paths through the converter are analysed. Safe and steady-state operating regions of the converter are studied in phasor diagrams to facilitate the design of simple controllers for active power transfer and reactive power generations. An investigation into the application of this topology to the back-to-back VSC HVdc interconnection is preformed via EMTDC simulations.
|
93 |
Characterization and design of high-switching speed capability of GaN power devices in a 3-phase inverter / Caractérisation et design de la monté en fréquence de découpage d'un onduleur 3 phases avec des transistors en GaNPerrin, Rémi 09 January 2017 (has links)
Le projet industriel français MEGaN vise le développement de module de puissance à base de compostant HEMT en GaN. Une des application industrielle concerne l’aéronautique avec une forte contrainte en isolation galvanique (>100 kV/s) et en température ambiante (200°C). Le travail de thèse a été concentré sur une brique module de puissance (bras d’onduleur 650 V 30 A). L’objectif est d’atteindre un prototype de facteur de forme peu épais, 30 cm2 et embarquant l’ensemble des fonctions driver, alimentation de driver, la capacité de bus et capteur de courant phase. Cet objectif implique un fort rendement énergétique, et le respect de l’isolation galvanique alors que la contrainte en surface est forte. Le manuscrit, outre l’état de l’art relatif au module de puissance et notamment celui à base de transistor GaN HEMT, aborde une solution d’isolation de signaux de commande à base de micro-transformateur. Des prototypes de micro-transformateur ont été caractérisés et vieillis pendant 3000 H pour évaluer la robustesse de la solution. Les travaux ont contribué à la caractérisation de plusieurs composants GaN afin de mûrir des modèles pour la simulation circuit de topologie de convertisseur. Au sein du travail collaboratif MEGaN, notre contribution ne concernait pas la conception du circuit intégré (driver de grille), tout en ayant participé à la validation des spécifications, mais une stratégie d’alimentation du driver de grille. Une première proposition d’alimentation isolée pour le driver de grille a privilégié l’utilisation de composants GaN basse-tension. La topologie Flyback résonante avec clamp permet de tirer le meilleur parti de ces composants GaN mais pose la contrainte du transformateur de puissance. Plusieurs technologies pour la réalisation du transformateur ont été validées expérimentalement et notamment une proposition originale enfouissement du composant magnétique au sein d’un substrat polymère haute-température. En particulier, un procédé de fabrication peu onéreux permet d’obtenir un dispositif fiable (1000 H de cyclage entre - 55 ; + 200°C), avec un rendement intrinsèque de 88 % pour 2 W transférés. La capacité parasite d’isolation est réduite par rapport aux prototypes précédent. Deux prototypes d’alimentations à forte intégration utilisent soit les transistors GaN basse tension (2.4 MHz, 2 W, 74 %, 6 cm2), soit un circuit intégré dédié en technologie CMOS SOI, conçu pour l’application (1.2 MHz, 2 W, 77 %, 8.5 cm2). Le manuscrit propose par la suite une solution intégrable de mesure de courant de phase du bras de pont, basé sur une magnétorésistance. La comparaison expérimentale vis à vis d’une solution à résistance de shunt. Enfin, deux prototypes de convertisseur sont décrits, dont une a pu faire l’objet d’une validation expérimentale démontrant des pertes en commutation réduites. / The french industrial project MEGaN targets the development of power module based on GaN HEMT transistors. One of the industrial applications is the aeronautics field with a high-constraint on the galvanic isolation (>100 kV/s) and ambient temperature (200°C). The intent of this work is the power module block (3 phases inverter 650 V 30 A). The goal is to obtain a small footprint module, 30 cm2, with necessary functions such as gate driver, gate driver power supply, bulk capacitor and current phase sensor. This goal implies high efficiency as well as respect of the constraint of galvanic isolation with an optimized volume. This dissertation, besides the state of the art of power modules and especially the GaN HEMT ones, addressed a control signal isolation solution based on coreless transformers. Different prototypes based on coreless transformers were characterized and verified over 3000 hours in order to evaluate their robustness. The different studies realized the characterization of the different market available GaN HEMTs in order to mature a circuit simulation model for various converter topologies. In the collaborative work of the project, our contribution did not focus on the gate driver chip design even if experimental evaluation work was made, but a gate driver power supply strategy. The first gate driver isolated power supply design proposition focused on the low-voltage GaN HEMT conversion. The active-clamp Flyback topology allows to have the best trade-off between the GaN transistors and the isolation constraint of the transformer. Different transformer topolgies were experimentally performed and a novel PCB embedded transformer process was proposed with high-temperature capability. A lamination process was proposed for its cost-efficiency and for the reliability of the prototype (1000 H cycling test between - 55; + 200°C), with 88 % intrinsic efficiency. However, the transformer isolation capacitance was drastically reduced compared to the previous prototypes. 2 high-integrated gate driver power supply prototypes were designed with: GaN transistors (2.4 MHz, 2 W, 74 %, 6 cm2), and with a CMOS SOI dedicated chip (1.2 MHz, 2 W, 77 %, 8.5 cm2). In the last chapter, this dissertation presents an easily integrated solution for a phase current sensor based on the magnetoresistance component. The comparison between shunt resistor and magnetoresistance is experimentally performed. Finally, two inverter prototypes are presented, with one multi-level gate driver dedicated for GaN HEMT showing small switching loss performance.
|
94 |
Autonomní záložní zdroj 230V/50Hz/300VA s bateriovým napájením 12V / Back-up power supply 230V/50Hz/300VA with a battery supply 12VSnítilý, David January 2008 (has links)
The aim of this project is to describe, design and create a converter from 12V DC to 230 VRMS. The power of this device is about 500W. The device consists of two main converters. The first one is step-up DC/DC converter and the other is DC/AC inverter. Step-up converter is designed as a resonant converter. It is useful for pushing down losses in semiconductors and inceasing efficiency. The inverter is changing DC voltage from the first converter to AC voltage. Control of this device is realized with DSP Motorola. This device should be used mainly for supply common devices up to 500W. Main usage is planed in a car or to another place where is not posible to connect some device to plug.
|
95 |
Static and Dynamic Characterization of power semiconductorsMejean, Alexandre January 2019 (has links)
Characterizing power switches is an indispensable step when designing a converter. This thesisinvestigates ways to achieve static and dynamic characterization of semiconductors for high power applications such as power grid or train traction. The static characterization has been tested with a Keysight B1506A device analyzer. The problems encountered have been analyzed and corrected.Then the design of a high current switching test bench for dynamic characterization is explained. The full-bridge configuration allows controlled and spontaneous commutations so the bench can measure hard and soft switching. The voltage can be up to 10 kV and the current up to 3 kA during the commutation. The choice of the probes is justified. The issues of bandwidth, input impedance and common mode current are taken into account. Data are processed in order to interpolate theswitching loss in hard and soft switching. / Karaktärisering av halvledarbrytare är ett viktigt steg när man utformar en omvandlare. Dennaavhandling undersöker olika sätt att uppnå statisk och dynamisk karakterisering av halvledare för högeffekttillämpningar såsom elnät eller ellok. Statisk karaktäriseringen har utförts med en Keysight B1506A-enhetsanalysator. De problem som uppstått har analyserats och korrigerats.Utformningen av en testbänk för dynamisk karakterisering förklaras. Den kompletta bryggkonfigurationen möjliggör kontrollerad och spontan kommutation med spänningar upp till 10 kV och strömmar upp till 3 kA så att bänken kan mäta hård och mjuk växling. Valet av sonderna förklaras. Frågorna om bandbredd, ingångsimpedans och common-mode ström tas med iberäkningen. Data bearbetas för att interpolera kopplings förlusten i hård och mjuk växling.
|
Page generated in 0.064 seconds