This project investigates the optimisation of platinum-group metals recovery at the Mimosa Mine in Zimbabwe. The first part of this research investigates how collector performance can be improved by using collector combinations (mixtures) of the standard sodium iso-butyl xanthate with a secondary collector. The synergistic effect of the sodium-iso-butyl-xanthate (SIBX) combined with trithiocarbonates (TTCs) or dithiophosphates (DTP) was investigated. The short chain and the long chain TTCs were investigated. These collector combinations were studied at various molar percent ratios. The SIBX:DTP combination was studied at a 1:1 mass ratio or molar ratio of 1:1.3. Amongst all the collector combinations, it was established that the SIBX/DTP combination improved sulphur recoveries by 10% and subsequently the PGE+Au recovery by 10% compared to when the SIBX was used on its own. The C4-TTC showed poor performance in the sulphur recovery; however an improvement in PGE + Au recovery was noticeable. There was generally no significant metallurgical improvement with respect to final grades and recoveries with C10 and C12TTC mixtures with SIBX. However, the 6.25 molar per cent substitution of SIBX by C12TTC appeared to show some improvement on sulphur but not on PGM+Au recovery and grade. It was therefore concluded that the SIBX/DTP combination at 1:1 mass ratio (total moles of 0.64) showed a potential to improve the grades and recoveries of the Mimosa Mine. The Mimosa ore is characterised by an unusually large amount of talc, which often causes problems during the flotation of the PGM minerals due to the fact that talc consumes high amount of reagents. Therefore the purpose of the second part of this thesis was to investigate the possibility of removing talc prior to the flotation process by de-sliming. Two cyclones (36.9 mm and 76.0 mm) were used for de-sliming the flotation feed. De-sliming the ore was able to reduce the depressant dosage up to 300 g/t as opposed to 500 g/t that is used at Mimosa Mine. / Dissertation (MSc)--University of Pretoria, 2008. / Materials Science and Metallurgical Engineering / unrestricted

In general, the stability of suspension can be studied using two methods. <i>One</i> is to directly measure the forces between two interacting surfaces in media. <i>The other</i> is to study the interfacial surface free energies of the particles in suspension. Direct surface force measurements were conducted between silica surfaces in octadecyltrimetylammonium chloride (C₁₈TACl) solutions using an Atomic Force Microscope (AFM). The results showed that the hydrophobic force existed in both air-saturated and degassed C₁₈TACl solutions. The attraction decreased with NaCl addition, and was the strongest at the point of charge neutralization (p.c.n.) of silica substrate. The force measurement results obtained in C_nTACl solutions showed that the attractions decayed exponentially and became the maximum at the p.c.n.'s. The decay lengths (<i>D</i>) increased with surfactant chain length. The measured forces were fitted to a charged-patch model of Miklavic <i>et al</i>. (1994) with rather large patch sizes. It was also found that the decay length decreased linearly with the effective concentration of the CH2/CH3 groups raised to the power of -1/2. This finding is in line with the model of Eriksson <i>et al</i>. (1989). It suggested that the long-range attractions are hydrophobic forces originating from the changes in water structure across a hydrophobic surface-solution interface. For the TiO₂/water/TiO₂ system, the Hamaker constant was found to be 4±1×10^-20 J. The force curves obtained in the TiO₂/C_nTACl system showed a repulsion-attraction-repulsion transition with increasing surfactant concentration. The long-range attraction observed between TiO₂ surfaces in C_nTACl solutions reached maximum at the p.c.n., and the decay length increased with chain length. In present work, the thin-layer wicking technique was used to determine the surface free energy (γ_s) and its components of talc samples. The results showed that the basal surfaces of talc are weakly basic while the edge surfaces are acidic. The effect of chemicals on the surface free energies of talc was systemically studied. The results showed that CMC (carboxymethyl cellulose sodium salt) and EO/PO (ethylene oxide/propylene oxide) co-polymers made talc surface hydrophilic by increasing the surface free energies, especially γ^LW and γ^-. SOPA (sodium polyacrylate) increased greatly the zeta-potentials instead of the surface free energies. / Ph. D.

This dissertation explores the emergence of surf tourism as a significant aspect of rural communities. It uses an inductive qualitative approach focused on Tofino, British Columbia, Canada as an example to provide an in-depth exploration of a rural community effected by this phenomenon. Qualitative interviews were conducted with a snowball sample of key informants to address the following research objectives: (1) What factors have influenced the evolution of surf tourism in Tofino; (2) How might the evolution of surf tourism in this case study relate to the Tourism Area Life Cycle (TALC); (3) What is the impact of surf tourism on the broader community development of Tofino? Analysis of the Tofino data elicited following themes: (1) For some, surfing is a desirable lifestyle, reflecting in some ways the concepts of specialization, serious leisure, and community’s identity; (2) Surf shops are a community hub for local surfers and surf tourists; (3) Pacific Rim National Park plays a critical role in the region, contributing to surfing and the surf tourism industry, but has yet to fully engage with surfers or the surfing industry; (4) New and more affordable equipment technology has brought increased access to cold-water surf and surf tourism, reducing what may have constrained the early development of surf tourism; (5) Considerable increases in the supply and demand for surfing in Tofino have occurred, tempered by the increased number of surfing competitions and other new tourism segments that exist in the community; (6) Increasing safety issues may undermine the growth of surf tourism; (7) Limits to surf tourism growth are evident regarding facility and physical carrying capacity; (8) As a result of the considerable growth of surfing in Tofino, recreational crowding, and conflict are in evidence, as are coping mechanisms; (9) ‘Localism’ exists in Tofino, but perhaps less so than in other destinations which have a fixed beach break; (10) Surf tourism has the potential for positive and negative impacts on First Nations communities in the region; and (11) Local government plays an important role. These themes were then analyzed and linked to the following theoretical concepts: serious leisure; specialization; leisure constraints; localism; violence; conflict; crowding, carrying capacity, amenity migration, the Tourism Area Life Cycle (TALC); and, rural tourism. This led to some intriguing findings. For example, unlike most other popular surf tourism destinations, crowding is not so apparent in the surf because the surf breaks in the Tofino area are primarily beach breaks that constantly shift as the bathymetry of the ocean floor changes with tides and currents, resulting in constant wave changes. This contrasts with fixed break conditions found elsewhere, so in Tofino it is easier to avoid other surfers by simply moving to another part of the wave. When the Tofino findings were compared with TALC, some similarities and differences were noted. Factors that appear to be consistent with the TALC model are: increasing numbers of tourists, changing type of tourists (e.g. more mass tourists, compared to the early days of surf tourism), increasing numbers of tourism facilities, increased levels of marketing, increased levels of interaction between visitors and local communities (perhaps leading to instances of conflict, and localism), and increased economic benefits to the community. However, one possible departure from the expected trajectory is impacts on the natural environment, which have increased in some ways, but are improved in other ways. There has been some environmental change in terms of the growth in the town of Tofino, and with the development of lodgings near to the surrounding beaches. However, much of the larger landscape, remains largely intact or less impacted than what might have occurred without the presence of Pacific Rim National Park, and the Clayoquot Biosphere Reserve. Further, the TALC model suggests that the development of tourism will lead to lesser local control of development. The Tofino findings suggest that there remains a great deal of local control and that local government support the tourism industry, including surf tourism. It was noted that the emerging surf tourism refers to several concepts found in the general nature tourism literature, such as crowding, conflict and carrying capacity, but the surf tourism literature tends to overlook the complexity of some of these concepts. For example, future surf tourism research might consider more explicit examination of the various dimensions of conflict described in this study, including in group and outgroup conflict, interpersonal conflict and social values conflict. There is little evidence of the incorporation of these concepts in the surf tourism literature. Finally, the data exposed a high level of social capital within the surf community and also between surfers and non-surfers as a facet of a close-knit rural community dependent to a degree on surf tourism as a social driver manifesting in mutual cooperation, trust and reciprocity occurring in social institutions such as surf-shops. / Graduate

Made available in DSpace on 2014-10-09T12:26:24Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:09:59Z (GMT). No. of bitstreams: 0 / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Made available in DSpace on 2014-10-09T12:26:24Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:09:59Z (GMT). No. of bitstreams: 0 / Com o propósito de melhorar a estabilidade dimensional, melhorar propriedades de resistência elétrica, mecânica, ao calor entre outras dos polímeros, novas cargas e reforços são testados com esse propósito. As cargas mais utilizadas, para propiciar as características mencionadas anteriormente, são as fibras de vidro e de carbono, as cargas minerais como o carbonato de cálcio precipitado, o talco e a micro esfera de vidro. O objetivo principal deste trabalho foi estudar as potencialidades da cinza da casca de arroz (CCA) como uma carga, já que ela é constituída em 96% de dióxido de silício e compará-la com o talco que é a carga mineral mais utilizada. Estes estudos foram realizados a partir da elaboração de um composto formado pela cinza da casca de arroz refinada e a poliamida 6 (PA 6) que é um dos principais plásticos de engenharia com aplicações em todas as áreas produtivas. As amostras foram injetadas e irradiadas em um acelerador de elétrons. Posteriormente suas propriedades mecânicas e térmicas foram medidas. Também foram injetadas peças automotivas para verificar a processabilidade da PA 6 com CCA. Os resultados mostraram que a utilização da cinza da casca de arroz como carga para compostos de poliamida 6 é tecnicamente e economicamente viável. A irradiação do composto estudado (PA 6 com 30% de cinza da casca de arroz) não trouxe melhorias significativas nas propriedades mecânicas e térmicas avaliadas. / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

This diploma thesis deals with study of crystalline structure of polyhydroxybutyrate (PHB), which contains different types of additives for studying of their nucleation activity and which were prepared by mixing. It is about boronitrid (BN), sacharin, hydroxapatit, plasticizer Tegmer a tree types of talc. Crystal structure was analysed by differential scanning calorimetry and x-ray diffraction, supramolecular structure was observed by optical microscopy (polarized and confocal laser scanning). Nucleating activity was evaluated by isothermal and non-isothermal crystallization made on calorimeter and heated table of optical microscope. There is not influence of additives on crystallographic structure, but additives affects number and size of spherulites including crystal domains defects, which can have impact on final mechanical properties. BN and talcs react as nucleating agents, other additives during low and high cooling speeds (vc) inhibit nucleation and in middle cooling speeds are without effect. Nucleating activity is not evaluated by numerically, because decrease of crystallization temperature together with vc is not linear. Results of direct methods are based on picture analysis, which is great benefit for understanding of crystal behaviour of PHB.

No description available.

Le centre de recherche ArcelorMittal de Montataire développent de nouvelles solutions acier innovantes associant métal et polymère. Pour les ailes de voiture, le composite retenu est un matériau multicouche composé d’une lame d’acier sur laquelle est déposé un film mince de polypropylène choc chargé avec des particules minérales par l’intermédiaire d’une fine couche de polypropylène fonctionnalisé par le greffage d’anhydride maléique. Afin de prévoir et de connaitre le comportement de la partie organique du matériau lors de sa mise en forme par emboutissage et à posteriori de prédire l’état de ses propriétés mécaniques lors de son utilisation, la détermination des lois de comportement mécanique vrai et intrinsèque sur le modèle de la loi G’sell et Jonas est nécessaire. Ces lois sont définies selon trois chemins de déformation : la traction uniaxiale, le cisaillement simple et la traction plane. Les micromécanismes de déformation de la microstructure semi-cristalline des différentes formulations des matériaux selon leur mode de sollicitation mécanique ont été étudiés. Les résultats obtenus Post Mortem et In Situ ont permis la description qualitative et quantitative des évolutions des principales modifications microstructurales. Ces dernières diffèrent avec l’ajout de charges minérales. Deux nouvelles méthodes, la Tomographie X et la spectroscopie Raman permettent la détermination de la déformation volumique dans le cas de matériau de géométrie fine (300 µm). Le retrait lors d’un cycle thermique est étudié. Les influences du chauffage, de la formulation et de la microstructure (orientation des chaînes macromoléculaires et endommagement volumique) sont décrites / The ArcelorMittal research centre of Montataire elaborates innovative steel / polymer products. In the case of automotive fenders, the composite is a multilayered material. A thin impact polypropylene film is laminated on steel using a thin layer of a functionalized polypropylene. Mineral particles are added to improve stiffness. In order to predict and understand the behaviour of the organic layer all along its production process and finally to be able to characterize the state of its mechanical properties in use, the determination of the true and intrinsic mechanical behaviour laws according to the G’sell and Jonas model is necessary. These laws are obtained for three different mechanical paths: uniaxial tensile, simple shear and plane tensile. The deformation micromechanisms of the impact polypropylene semi-crystalline microstructure which depend on the materials formulations and on the mechanical path used are studied. Post Mortem and In Situ results give qualitative and quantitative description of the main microstructural modifications. Two new methods, X Tomography and Raman spectroscopy allow the quantification of the volume deformation which is developed during tensile tests. They are mainly available for very thin samples. X radiography and VideoTraction™ are not suitable anymore for this kind of geometry. Finally, the thermo-mechanical phenomenon of shrinkage which occurs during thermal treatment above the material melting point is analysed. Influences of the heating conditions, of the material formulations and of the material microstructure are described. Special overviews are done on the macromolecular chains orientation and on the volume damage influences

Dans le contexte de développement durable actuel, les matériaux biosourcés et biodégradables commencent à prendre une place importante d’un point de vue économique et écologique. L’objectif de remplacer les polyoléfines utilisées actuellement dans des domaines clés tels que l’emballage et l’automobile est cependant difficile car les matériaux « verts » sont rarement aussi performants. Ils présentent en général des lacunes au niveau de leurs propriétés mécaniques et sont sensibles à des dégradations qui limitent leur durée de vie. Le poly(butylène succinate) est un polyester connu depuis longtemps mais qui regagne de l’intérêt grâce à son potentiel biosourcé et biodégradable ainsi que ses propriétés mécaniques proches de celles des polyoléfines. Néanmoins, sa rigidité est encore trop faible et sa sensibilité importante à l’hydrolyse limite son utilisation dans le temps, même dans des conditions standards de température et d’humidité. Des améliorations de la stabilité du PBS sont possibles et plusieurs solutions ont été envisagées. L’intérêt s’est porté sur la modification de la balance hydrophile/hydrophobe du PBS par l’ajout d’un comonomère ramifié très hydrophobe, le Pripol 1009 ou possédant un cycle aromatique, l’acide téréphtalique. L’addition de charges dans le matériau peut également s’avérer efficace pour neutraliser les fins de chaines acides catalysant la dégradation, en utilisant du carbonate de calcium, ou pour limiter la perméabilité du matériau, par incorporation de talc. Dans l’optique de moduler les propriétés mécaniques du PBS, la voie de modification la plus fructueuse est le mélange par incorporation de charges minérales, comme le carbonate de calcium ou le talc, ou le mélange avec d’autres polyesters possédant une rigidité plus importante, tels que le poly(acide lactique) ou le poly(butylène téréphtalate). Les mélanges doivent présenter une bonne compatibilité et être mis en œuvre à des températures convenables pour limiter la dégradation du PBS et conserver la ductilité du matériau final, comme c’est le cas des mélanges PBS/PLA. Des combinaisons ont également été envisagées entre les différentes solutions efficaces pour améliorer à la fois les propriétés mécaniques et la stabilité face à l’hydrolyse chimique. / Within the frame of sustainable development, biobased and biodegradable polymers are going to play an important role according to economic and environmental perspectives. The polyolefins currently used in packaging and automotive industries will be replaced by biomaterials. The poly(butylene succinate), an “old” aliphatic polyester, has recently regained interest thanks to its biobased and biodegradable potential and mechanical properties similar to polyolefins. However, this polyester is very sensitive to degradation even at mild ambient conditions and, even though its flexibility is comparable to polyethylene or polypropylene, its modulus is too low. Some modifications of the chemical structure were considered to improve the long-term use of PBS. The synthesis of random copolymers using long-chain fatty acid Pripol 1009 or terephthalic acid allows to reduce significantly the hydrolysis rate and properties are maintained during a longer time. The incorporation of fillers like calcium carbonate and talc also enhance the PBS stability. The addition of calcium carbonate neutralizes carboxyl terminal group, which play an autocatalytic role in the hydrolytic degradation. High aspect ratio of talc increases the gas and liquid diffusion path, reducing permeability and providing better barrier properties to the material. In order to improve Young’s modulus, formulating blends with mineral fillers like calcium carbonate and talc, or with more rigid polyesters like polylactic acid or poly(butylene terephthalate) are efficient. The most interesting results are obtained by using calcium carbonate and polylactic acid, which allow the preservation of PBS’s flexibility. Processing parameters should be maximized to limit the degradation of PBS. Combinations of the most interesting solutions were investigated and lead to materials which fulfill the required specifications.

Pacientes com comprometimento pleural por neoplasias malignas freqüentemente apresentam derrame pleural recidivante. Nestes casos, a sínfise das membranas pleurais (pleurodese) com a finalidade de evitar o acúmulo de líquido no espaço pleural deve ser considerada. O talco é o agente mais utilizado indicado para essa finalidade. Entretanto, seu uso terapêutico continua controverso devido aos efeitos deletérios que podem advir de sua utilização. O mais grave entre todos é a insuficiência respiratória aguda, que pode evoluir para a síndrome do desconforto respiratório agudo (SDRA). Essa complicação pode estar relacionada com a composição, com o tamanho das partículas de talco e com a resposta inflamatória desencadeada pelas mesmas. O objetivo deste estudo foi avaliar os efeitos pulmonares e sistêmicos em resposta à injeção intrapleural (IIP) de talco de partículas pequenas (TP) e de partículas de tamanhos diversos (TM). Cem coelhos foram submetidos à IIP com talco. Metade dos animais foi injetada com TP (diâmetro médio= 6,41 mm) e outra metade com TM (diâmetro médio= 21,15 mm), que é o talco usado na prática clínica. Quinze coelhos compuseram o grupo controle. Foram avaliados a celularidade, os níveis de desidrogenase lática (DHL), proteína C reativa (PCR), interleucina-8 (IL-8) e fator de crescimento endotelial vascular (VEGF) no sangue e no lavado broncoalveolar (LBA) às 6, 24, 48, 72 e 96 horas após a IIP. Realizou-se também a quantificação de partículas de talco e a análise histológica dos pulmões. Utilizamos o teste t e Anova na análise estatística, considerando p< 0,05 como significância estatística. A maioria dos parâmetros avaliados apresentou níveis mais elevados no sangue e no LBA dos animais injetados com TP ou TM quando comparados ao grupo controle, sugerindo uma resposta sistêmica e pulmonar à IIP de talco. Com relação aos grupos de talco, os níveis de PCR e de IL-8 apresentaram-se mais elevados no sangue e no LBA dos animais injetados com TP. Partículas de talco foram observadas em todas as lâminas examinadas, sem diferenças significativas entre os grupos. Os pulmões dos animais injetados com TP apresentaram infiltrado linfomononuclear mais exuberante que no grupo TM. A resposta inflamatória pulmonar antecedeu (24 h) a resposta sistêmica (48 h), sugerindo que o pulmão é o principal órgão da resposta sistêmica aguda. Estes achados estudo nos permitem concluir que o talco calibrado com partículas maiores deva ser utilizado na prática clínica, objetivando uma pleurodese mais segura. / Talc has been the pleurodesis agent of choice for the local treatment of recurrent pleural diseases. However, serious concerns exist about its safety. The acute respiratory failure is considered its most serious complication. The physiopathologic mechanisms involved are still unclear. It has been attributed to the systemic dissemination of small talc particles, to the composition of talc and to the inflammatory response. The purpose of this study was to evaluate the systemic and pulmonary response following intrapleural instillation of small particles talc (ST) and mixed particles talc (MT). One hundred rabbits received intrapleural instillation of talc as follows: fifty rabbits were instilled with ST (mean diameter=6,41 microns), and 50 rabbits with MT (mean diameter= 21,15 microns). As control (without talc instillation) were used 15 animals. We studied the pulmonary and systemic inflammatory response (total cell count and differential, levels of lactate dehydrogenase (LD), C-reactive protein (PCR), interleukin-8 (IL-8) and human vascular endothelial growth factor (VEGF) in serum and bronchoalveolar lavage (BAL). Histologic analysis of both lungs and quantitation of talc particles were done at 6, 24, 48, 72 and 96h. ST group showed higher pulmonary and systemic inflammatory response than did the MT group. PCR and IL-8 concentrations were higher in serum and BAL of ST group than the MT group. Many talc particles were observed in the pulmonary tissue of both talc groups, but without statistical significance. We also observed a predominance of cellular infiltrates (lymphomononuclear cells) in the lungs of ST group. The pulmonary inflammatory response (increased IL-8 in BAL) was earlier (24h) than the systemic inflammatory response (48 h). These observations suggest that the main organ in the systemic inflammatory acute response is lung. So, we recommend the clinical use of mixed talc without small particles to induce safety pleurodesis.