High strength nickel-base superalloys have been used in turbine blades for many years because of their superior performance at high temperatures. In such environments superalloys have limited oxidation and corrosion resistance and to solve this problem, protective coatings are deposited on the surface. The positive effect of coatings is based on protecting the surface zone in contact with hot gas atmosphere with a thermodynamically stable oxide layer that acts as a diffusion barrier. During service life, mechanical properties of metallic coatings can be changed due to the significant interdiffusion between substrate and coating. There are also other degradation mechanisms that affect nickel-base superalloys such as low cycle fatigue, thermo-mechanical fatigue and creep. The focus of this work is on a study of low cycle fatigue and out-of-phase thermo-mechanical fatigue behaviour of three uncoated and coated nickel-base superalloys. Polycrystalline IN792 and two single crystals CMSX-4 and SCB were coated with four different coatings; an overlay coating AMDRY997 (NiCoCrAlYTa), a platinum aluminide modified diffusion coating RT22 and two innovative coatings with a NiW interdiffusion barrier in the interface called IC1 and IC3. A low cycle fatigue and thermo-mechanical fatigue device was designed and set-up to simulate service loading of turbine blades and vanes. The low cycle fatigue tests were run at 500oC and 900oC while the thermo-mechanical fatigue tests were run between 250oC and 900oC.To simulate long service life, some coated specimens were exposed at 1050oC for 2000 h before the tests. The main conclusions are that the presence of the coatings is, in most cases, detrimental to LCF lives of the superalloys at 500oC while the coatings do improve the LCF lives of the superalloys at 900oC. Under TMF loading conditions, the coatings have negative effect on the lifetime of IN792. On single crystals, they are found to improve TMF life of the superalloys, especially at lower strains. The tests also indicate that long-term aging influences the fatigue and fracture behaviour of coated superalloys by oxidation and diffusion mechanisms when compared to non-aged specimens. The aged specimens exhibit longer life in some cases and shorter life during other test conditions. Fatigue cracks were in most cases initiated at the surface of the coatings, growing transgranularly perpendicular to the load axis.

Energy efficiency is a vital key component when designing and miniaturizing self sustained microsystems. The smaller the system, the smaller is the possibility to store enough stored energy for a long and continuous operational time. To move such a system in an energy efficient way, a piezoelectrical locomotion module consisting of four resonating cantilevers has been designed, manufactured and evaluated in this work. The combination of a suitable substrate, a multilayered piezoelectric material to reduce the voltage, and a resonating drive mechanism resulted in a low power demand. A manufacturing process for multilayer cantilever actuators made of P(VDF-TrFE) with aluminum electrodes on a substrate of flexible printed circuit board (FPC), has been developed. An important step in this process was the development of an etch recipe for dry etching the multilayer actuators in an inductive plasma equipment. Formulas for the quasi static tip deflection and resonance frequency of a multilayered cantilever, have been derived. Through theses, it was found that the multilayered structures should be deposited on the polymer side of the FPC in order to maximize the tip deflection. Both a large and a miniaturized locomotion module were manufactured and connected by wires to verify that the three legged motion principal worked to move the structures forward and backward, and turn it right and left. By touching and adding load, to a fourth miniaturized cantilever, its ability to act as a contact sensor and carry object was verified. The presented locomotion module is part of a multifunctional microsystem, intended to be energy efficient and powered by a solar panel with a total volume of less than 25 mm3 and weight 65 mg. The whole system, consisting of a solar cell, an infra red communication module, an integrated circuit for control, three capacitors for power regulating, the locomotion module and an FPC connecting the different modules, was surface mounted using a state of the art industrial facility. Two fully assembled systems could be programmed both through a test connector and through optical sensors in the multifunctional solar cell. One of these was folded together to the final configuration of a robot. However, the entire system could not be tested under full autonomous operating conditions. On the other hand, using wires, the locomotion module could be operated and used to move the entire system from a peak-to-peak voltage of 3.0 V.

Surface energy plays a major role in many phenomena that are important in technological and industrial processes, for example in wetting, grain growth and sintering. In this thesis, such surface-energy driven processes are studied by means of the phase-field method. The phase-field method is often used to model mesoscale microstructural evolution in materials. It is a diffuse interface method, i.e., it considers the surface or phase boundary between two bulk phases to have a non-zero width with a gradual variation in physical properties such as energy density, composition and crystalline structure. Neck formation and coarsening are two important diffusion-controlled features in solid-state sintering and are studied using our multiphase phase-field method. Inclusion of Navier-Stokes equation with surface-tension forces and convective phase-field equations into the model, enables simulation of reactive wetting and liquid-phase sintering. Analysis of a spreading liquid on a surface is investigated and is shown to follow the dynamics of a known hydrodynamic theory. Analysis of important capillary phenomena with wetting and motion of two particles connected by a liquid bridge are studied in view of important parameters such as contact angles and volume ratios between the liquid and solid particles. The interaction between solute atoms and migrating grain boundaries affects the rate of recrystallization and grain growth. The phenomena is studied using a phase-field method with a concentration dependent double-well potential over the phase boundary. We will show that with a simple phase-field model it is possible to model the dynamics of grain-boundary segregation to a stationary boundary as well as solute drag on a moving boundary. Another important issue in phase-field modeling has been to develop an effective coupling of the phase-field and CALPHAD methods. Such coulping makes use of CALPHAD's thermodynamic information with Gibbs energy function in the phase-field method. With the appropriate thermodynamic and kinetic information from CALPHAD databases, the phase-field method can predict mictrostructural evolution in multicomponent multiphase alloys. A phase-field model coupled with a TQ-interface available from Thermo-Calc is developed to study spinodal decomposition in FeCr, FeCrNi and TiC-ZrC alloys. / QC 20100622

Experiments on the production of porous metallic materials were performed on Fe-base and Al-base alloys. The method involves dissolution of gases in the liquid state and solidification at various cooling rates. The alloy compositions were selected to induce solidification of primary particles intended to control the pore distribution. For the Fe-base alloys, nitrogen was introduced into the melt by dissolution of chromium nitride powder. Fe-Cr-Mn-Si-C alloys featuring M7C3 carbide particles were selected. For the Al-base alloys, hydrogen gas was dissolved into the melt by decomposition of water vapor. Al-Ti and Al-Fe alloys featuring primary Al3Ti and Al3Fe intermetallic particles, respectively, were considered. In the Fe-base alloys, a homogeneous distribution of gas pores through the specimens’ volume was obtained at high cooling rate (water quenching) and after introduction of external nucleating agents. In the case of the Al-base alloys, a good pore distribution was observed at all cooling rates and without addition of nucleating agents. Calculations of the variation of nitrogen (respectively hydrogen) solubility based on Wagner interaction parameters suggest that pore nucleation and growth occur during precipitation of the primary particles (M7C3 carbides, Al3Ti or Al3Fe intermetallics), due to composition changes in the melt and resultant supersaturation with gas atoms. Microscopic analyses revealed that the primary particles control the pore growth in the melt and act as barriers between adjacent pores, thereby preventing pore coalescence and promoting a fine pore distribution. Uniaxial compression testing of the porous Al-Ti and Al-Fe materials showed the typical compressive behavior of cellular metals. Further work is needed to improve the quality and reproducibility of the porous structures which can possibly be used in energy absorption or load-bearing applications. As a corollary result of the quenching of hypereutectic Fe-Cr-Mn-Si-C alloys in the experiments of synthesis of porous metals, a homogeneous featureless structure was observed in some parts of the samples, instead of the equilibrium structure of M7C3 and eutectic phases. Subsequent investigations on rapid solidification of Fe-base alloys at various alloy compositions and cooling rates led to the formation of a single-phase structure for the composition Fe-8Cr-6Mn-5Mo-5Si-3.2C (wt.%), at relatively low cooling rates (≈103 K/s) and for large sample dimensions (2.85 mm). The single phase, which is likely to be the hcp ɛ-phase, was found to decompose into a finely distributed structure of bainite and carbides at ≈600 °C. The annealed structure showed very high hardness values (850 to 1200 HV), which could be exploited in the development of high-strength Fe-base materials. / QC 20100809

The primary intention with this Doctoral thesis is to fillin the knowledge gaps and raise the level of understandingregarding the different metal dusting mechanisms in general andexplain the process in detail for high alloyed materials.Considerable effort is put into identifying the driving forcesand elucidating the diffusional processes in metal dusting. The results are based on a series of long-term laboratory exposures of stainless steels and high-performance commercial alumina-forming Fe- and Ni-base alloys in synthesis gasmixtures, plus a separate shorter study on ultra pure iron. ANi-base alloy was also investigated after a two years field exposure in a methanol plant. Post exposure metallographic examinations and analysis aswell as thermodynamic calculations were made in order toidentify and describe the operating metal dusting mechanisms.Two main mechanisms were previously used to explain metaldusting, one on the basis of decomposition of metastable carbides (Type I) the other on graphite formation (TypeII). A new metal dusting mechanism has been identified in this Thesis which appears on high alloyed steels and Ni-base alloys,an active corrosion induced by carbon and oxygen, denoted TypeIII. Both the mechanisms and the type of corrosion products were consistent with the thermodynamic conditions of the material under the influence of a carbon and oxygen gradient.It was shown that this mechanism not only accelerates the metaldusting process, in fact, it determines the overall metaldusting kinetics on stainless steels and Ni-base alloys. Another feature, which may occur at temperatures where metalbulk and even static grain boundary diffusion is too slow forexplaining the metal dusting corrosion process, was identifiedon a Ni-base alloy. It involves a fast growing cellular structure with discontinuous precipitated carbides whichprovides fast metal dusting kinetics by the Type IIImechanism. A Type IV metal dusting mechanism, continued fragmentationby graphitization until nano-sized particles are formed andcatalyse carbon nanotube formation is also described. Thesteady state process and the driving force for metal dusting onpure iron was identified and described. With these additional processes it is now possible to extendour understanding of the metal dusting processes to a widerange of engineering alloys. / QC 20100825

For many decades zirconium alloys have been commonly used in the nuclear power industry as fuel cladding material. Besides their good corrosion resistance and acceptable mechanical properties the main reason for using these alloys is the low neutron absorption. Zirconium alloys are exposed to a very severe environment during the nuclear fission process and there is a demand for better design of this material. To meet this requirement a thermodynamic database is useful to support material designers. In this thesis some aspects of the development of a thermodynamic database for zirconium alloys are presented. A thermodynamic database represents an important facility in applying thermodynamic equilibrium calculations for a given material providing: 1) relevant information about the thermodynamic properties of the alloys e.g. amount and composition of phases, oxygen activity, heat capacity etc, and 2) significant information for the manufacturing process e.g. heat treatment temperature. The basic information in the database is first the unary data, i.e. pure elements; those are taken from the compilation of the Scientific Group Thermodata Europe (SGTE) and then the binary and ternary systems. All phases present in those binary and ternary systems are described by means of the Gibbs energy as a function of composition and temperature. Many of those binary systems have been taken from published or unpublished works and others have been assessed in the present work. The elements included in the databse are: C, Fe, Cr, Nb, Ni, Mo, O, Si, Sn, and Zr + H, and the assessment performed under this thesis are: Cr-Sn, Mo-Zr, Sn-Zr, Fe-Nb-Zr and Nb-O-Zr. All the calculations have been made using Thermo-Calc software and the representation of the Gibbs energy obtained by applying Calphad technique with some use of ab initio calculations. / QC 20100902

In the present thesis, the correlation between ladle glaze and non-metallic inclusions in the ladle treatment was studied. A number of industrial trials with full scale ladle and laboratory works were performed to investigate the inclusions in the ladle treatment. BaO was used as tracer in the ladle slag to investigate the effect of slag on inclusion composition and the formation of non-metallic inclusions by ladle glaze. BaO was detected in the inclusions of all followed heats. This observation showed strong evidence for the generation of non-metallic inclusions by the ladle glaze. The increase of the fractions of BaO containing inclusions and their average content of BaO in the first heat with tracer suggested that the effect of slag on the composition of inclusions was a very slow process. The detachment of ladle glaze and the chemical transformations of oxide solution in the MgO matrix were investigated. The experimental results evidently showed that the ladle glaze could be the source of inclusions continually during the ladle treatment. Samples of liquid oxide solution to simulate the liquid oxide inclusions carried over from EAF were equilibrated with molten steel under controlled atmosphere. The results along with thermodynamic calculation suggested that the SiO2 content of inclusions from EAF could be considerably reduced by dissolved aluminium in the steel. This would explain the vanishing of inclusions containing high SiO2 content after deoxidation. Due to the lack of experimental data, the viscosities of slags in the Al2O3-CaO-MgO-SiO2 system were measured using the rotating cylinder method in the temperature range of 1720 to 1910 K. Eight different slag compositions related to the secondary steel making operations were selected. Viscosities in this system and its sub-systems were expressed as a function of temperature and composition based on the viscosity model developed earlier at KTH. The activities of oxide components in the Al2O3-CaO-MgO-SiO2 systems at 1873 K were measured by equilibrating liquid slag and metal. Either silicon or copper was used as the metal phase and the oxygen partial pressure was controlled with different mixing rates of Ar and CO gas flow in equilibrium with graphite. Iso-activity lines were drawn from the measured activity values in the isothermal section of the slag systems. Nine series of industrial trials were carried out using the same ladle in each series to examine the effect of ladle slag on the number of non-metallic inclusions in the next heat. It was found that the number of inclusions increased with SiO2 content of the ladle slag in the previous heat. No clear trends were found for the effects of viscosity and MgO activity of the previous slag on the number of inclusions. Theoretical analysis based on the experimental results suggested that the formation of 2CaO∙SiO2 followed but the dusting of the compound made the refractory more porous, which was reasonable for the number of non-metallic inclusions.

På dagens fönsterglasmarknad har produkter med samma funktioner och utseende fått olika namn. Detta är förvirrande och gör det svårt för en person som ska beställa fönsterglas att jämföra olika tillverkares produkter med varandra. Rapporten är tänkt som en översikt på de olika fönsterglasen som finns på marknaden idag och även på sådant som kan bli aktuellt i framtiden. Den berör också sådant som kan vara av värde att veta vid användning av fönsterglas. Målgruppen är alla som kan tänkas ha intresse i ämnet - alltifrån hobbybyggaren till fackmän i byggbranschen. Informationen är sammanställd från böcker, broschyrer, internet och experter på området fönsterglas.

Quality of the castings is affected by several factors which the designer should take into consideration during the product development process. Although residual stress is one of those, it is often not considered in practical computations. Hence residual stresses are one of the forgotten areas in designing of machine parts. This master thesis is focused on the investigation of residual stresses in a high pressure die casted component, with the aim of extending its service life, by taking results from the study as a feedback. The investigation of residual stresses was done on a variety of specimens, cast aluminum flywheel, provided by Husqvarna AB. This flywheel is a component in a product of the same company.In evaluating the residual stresses in the part, two tools-simulation and physical measurement were used. Moreover, comparison with these two methods is also done at an area of interest on the flywheel. The simulation was carried out by using MAGMAhpdc-a module for high pressure die casting process, from the commercial software package MAGMAsoft; while for the physical measurements, the hole drilling method was used, a method believed to be less accurate at low stresses areas. The findings obtained from this study show that the results from both procedures are close, with small deviations observed, which reveals the reliability of the hole drilling method even when the stress levels are low. It is also found that the compressive residual stresses dominate in the component-a preferred phenomenon with regards to residual stress.

Abstract Our bachelor degree thesis was carried out in collaboration with Ivar Petterssons Järnmanufaktur AB in Smålandsstenar. We were asked to replace their wedge housing, used to fasten the wires to the power lines, with a similar structure in a plastic material. The idea for this project started with Ivar Petterssons Järnmanufaktur AB having problems with the casting quality that forced them to perform expensive tests on each of the wedge houses to ensure the quality. They are currently produced in China which is also a major drawback because it requires expensive long delivery times. The method we used is Fredy Olsson's Princip- and Primärkonstuktion (1995). We have consistently been in the project on so-called "broad front", which means that you create several sketches, ideas and changes in parallel, and then evaluates all. With this method we were able to largely concentrate on the current part of the project, rather than using the more time-consuming "trail and error" method, which is basically doing one idea at a time, and evaluate them one by one. At first we were very optimistic and thought we would be able to order form for the injection moulding process, but as the project progressed we found we were not certain that the product would hold and we were forced to present the solution as a concept that will require testing before it’s finished, and not a finished solution.The results we presented for Ivar Pettersssons Järnmanufaktur is a complete drawing on our primary solution, including the release angles. This is because when they decide to go forth with the project, it will be possible to produce a tool without having to make changes to the drawings. Temporary financial calculation shows that the savings may be realized around 1 300 000 SEK by switching to a plastic construction. However we have not been able to verify hours and therefore no cost estimates for the testing done in Sweden, so the actual amount of money saved is larger.