Quantum computing and two dimensional van der Waals materials research have been two of the fastest growing fields of condensed matter physics research for the better part of the last two decades. In that time, advances in superconducting qubit design, materials and fabrication have improved their relaxation and coherence times by about 5 orders of magnitude. One of the key components that quantum devices such as qubits require are ultra low loss capacitance elements. Conventional parallel plate capacitors have been unable to fulfill this need due to bulk and inter-facial losses, necessitating the use of coplanar capacitors with extremely large footprints. In fact one of the driving forces behind increase coherence times has been the ever growing footprint of these coplanar capacitor pads, and the reduced electric field density and thus reduced surface losses that they provide. However, this style of capacitor creates a number of challenges when it comes to scaling the number of qubits in a system. First, the large geometric footprint of these pads limits the number of qubits that can be placed on a chip. Second, the dispersion of the electric field, above and below the plane of the capacitor pads can cause unwanted crosstalk between neighbouring qubits, again limiting the number of qubits that can be put on a chip without compromising coherence. Since the isolation of a single atomic layer of graphene in 2004 and the ability to create heterostructures of a variety of two dimensional materials, the field of van der Waals materials research has exploded at a similar rate. Single crystals of van der Waals materials, can be grown with extremely low defect densities, and then be stacked to create heterostructures with ultra-clean laminated interfaces. This work explores how van der Waals materials may be used to create low loss parallel plate capacitors. The parallel plate geometry confines the electric field between the crystalline materials and low loss interfaces of a van der Waals heterostructure, limiting both losses at the surfaces as well as undesired cross talk between qubits. We begin by studying the microwave losses in hexagonal boron nitride (hBN). Next we report a method to make low loss microwave contacts to air sensitive superconducting van der Waals materials like niobium diselinde (NbSe₂). Finally, we demostrate coherence in a transmon where the primary shunt capacitor is an all van der Waals parallel plate capacitor, achieving a 1000× reduction in geometric footprint, when compared to a conventional coplanar capacitor.

This dissertation focused on the potential use of highly charged nanoparticles to stabilize dispersions of weakly charged microparticles. The experimental components of the project centered on a model colloidal system containing silica microparticles at the isoelectric point where the suspensions are unstable and prone to flocculation. The stability of the silica suspensions was studied in the presence of highly charged nanoparticles. Initial experiments used polystyrene latex with either sulfate or amidine surface groups. Effective zeta potentials were measured with nanoparticle concentrations ranging from 0.001% to 0.5% vol. Adsorption levels were determined through direct SEM imaging of the silica microparticles, showing that the nanoparticles directly adsorbed to the microparticles (amidine more than sulfate), producing relatively large effective zeta potentials. However, stability experiments showed that the latex nanoparticles did not stabilize the silica but merely provided a reduction in overall flocculation rate. It was concluded that the zeta potential was an insufficient predictor of stability as there was still sufficient patchiness on the surface to allow for the silica surfaces to aggregate. Experiments using zirconia and alumina nanoparticles did achieve effective stabilization; both types stabilized the silica suspensions for longer than the observation period of approximately 15 hours. Stability was observed at concentrations of 10^-4% to 1.0% (zirconia) and 10^-2% vol. (alumina). These particles adsorbed directly to the microparticles (confirmed via SEM) and produced increasing effective zeta potentials with increasing nanoparticle concentrations. The adsorption resulted in significant electrostatic repulsion that was determined to be effectively irreversible using colloidal probe AFM. The improved stabilizing ability was attributed to the increased van der Waals attraction between the oxide nanoparticles (compared to polystyrene). Finally, an unexpected result of the CP-AFM force measurements showed that the repulsive forces between a nanoparticle-coated particle and plate lacked the normal dependence on the radius of the probe as predicted by the Derjaguin approximation. The forces observed in nanoparticle suspensions were virtually identical for 5 µm and 30 µm probes. Based on calculations of the shear rate in the gap, it was theorized that this phenomenon may have resulted from the shearing of adsorbed particles from the surfaces, which leads to similar interaction geometries for the two probe sizes. / Ph. D.

Sticky prey capture threads are produced by many members of the spider Infraorder Araneomorphae. Cribellar threads are plesiomorphic for this clade, and adhesive threads are apomorphic. The surface of cribellar thread is formed of thousands of fine fibrils. Basal araneomorphs produce cylindrical fibrils, whereas more derived members produce fibrils with nodes. Cribellar fibrils snag and hold rough surfaces, but other forces are required to explain their adherence to smooth surfaces. Threads of Hypochilus pococki (Hypochilidae) that are formed of non-noded fibrils hold to a smooth acetate surface with the same force under low and high humidities. In contrast, threads of Hyptiotes cavatus and Uloborus glomosus (Uloboridae) that are formed of noded fibrils hold with greater forces to the same surface at intermediate and high humidities. Threads spun by eight species representing seven genera and four families with noded fibrils absorb water, while that of two families, represented by one species each with smooth fibrils, repel water, indicating increase hygroscopisity associated with the presence of nodes. Additionally, equations describing van der Waals and hygroscopic forces can predict the observed stickiness of these threads. This model supports the hypothesis that van der Waals forces allow non-noded cribellar fibrils to adhere to smooth surfaces, whereas noded fibrils employ van der Waals forces at low humidities and add hygroscopic forces at higher humidities. Thus, there appear to have been two major events in the evolution of spider prey capture thread: the addition of hydrophilic nodes to the fibrils of cribellar threads and the replacement of cribellar fibrils by glycoprotein glue. / Master of Science

No description available.

This thesis considers the problem of determining Casimir-Lifshitz forces in inhomogeneous media. The ground-state energy of the electromagnetic field in a piston-geometry is discussed. When the cavity is empty, the Casimir pressure on the piston is finite and independent of the small-scale physics of the media that compose the mirrors. However, it is demonstrated that, when the cavity is filled with an inhomogeneous dielectric medium, the Casimir energy is cut-off dependent. The local behavior of the stress tensor commonly used in calculations of Casimir forces is also determined. It is shown that the usual expression for the stress tensor is not finite anywhere within such a medium, whatever the temporal dispersion or index profile, and that this divergence is unlikely to be removed by modifying the regularisation. These findings suggest that the value of the Casimir pressure may be inextricably dependent on the detailed behavior of the mirror and the medium at large wave vectors. This thesis also examines two exceptions to this rule: first, the case of an idealised metamaterial is considered which, when introduced into a cavity, reduces the magnitude of the Casimir force. It is shown that, although the medium is inhomogeneous, it does not contribute additional scattering events but simply modifies the effective length of the cavity, so the predicted force is finite and can be stated exactly. Secondly, a geometric argument is presented for determining a Casimir stress in a spherical mirror filled with the inhomogeneous medium of Maxwell's fish-eye. This solution questions the idea that the Casimir force of a spherical mirror is repulsive, but prompts additional questions concerning regularisation and the role of non-local effects in determining Casimir forces.

Les atomes neutres sont des candidats prometteurs pour la réalisation et l’étude d’états intriqués à quelques dizaines de particules. Pour générer de tels états, une approche consiste à utiliser le mécanisme de blocage dipolaire résultant des fortes interactions dipôle-dipôle entre atomes de Rydberg.Suivant cette approche, cette thèse présente la conception et la caractérisation d’un dispositif expérimental permettant de manipuler des atomes de 87Rb individuels piégés dans des pinces op- tiques microscopiques, et à les exciter vers des états de Rydberg. Un environnement électrostatique stable et des électrodes de contrôle permettent une manipulation fine de ces états. Avec deux pinces optiques séparées de quelques microns, nous démontrons le blocage de Rydberg entre deux atomes, et nous observons leur excitation collective.Enfin, en opérant en régime de blocage partiel, nous développons une méthode permettant de mesurer l’interaction de van der Waals ∆E = C6 /R6 entre deux atomes séparés par une distance R contrôlée. Les coefficients C6 obtenus pour différents états de Rydberg sont en bon accord avec des calculs théoriques ab initio, et nous observons l’augmentation spectaculaire de l’interaction en fonction du nombre quantique principal n de l’état de Rydberg. / Neutral atoms are promising candidates for the realization of entangled states involving up to a few tens of particles. To generate such states, one approach consists in using the dipole blockade mechanism, which results from the strong dipole-dipole interactions between Rydberg atoms.Following this approach, this thesis describes the design and the characterization of an experimental apparatus allowing to manipulate single 87Rb atoms trapped in microscopic optical tweezers, and to excite them towards Rydberg states. A stable electrostatic environment and controlled electrodes enable the fine manipulation of these states. Using two optical tweezers separated by a few microns, we demonstrate the Rydberg blockade between two single atoms, and we observe their collective excitation.Finally, by operating in the partial blockade regime, we develop a method allowing to measure the van der Waals interaction ∆E = C6 /R6 between two atoms separated by a controlled distance R. The C6 coefficients obtained for various Rydberg states agree well with ab initio theoretical calculations, and we observe the dramatic increase of the interaction with the principal quantum number n of the Rydberg state.

La plupart des objets quantiques individuels développés jusqu’à aujourd’hui ne permettent pas de satisfaire toutes les conditions nécessaires pour la construction d’un simulateur quantique. Une possibilité pour obtenir un système quantique robuste est de combiner plusieurs de ces approches. Dans cette thèse, nous décrivons les résultats obtenus sur deux systèmes expérimentaux développés dans ce but.La première partie de cette thèse décrit un système hybride d’atomes neutres couplés à des qubits supraconducteurs, en construction à l’Université du Maryland. La solution envisagée pour placer un ensemble d’atomes froids à proximité de la surface supraconductrice est de piéger les atomes dans le champ évanescent se propageant autour d’une fibre optique nanométrique. Nous avons développé un dispositif permettant la production de fibres optiques nanométriques de transmission optique supérieure à 99.95% dans le mode fondamental. Nous avons également optimisé la transmission de quelques modes d’ordres supérieurs, ce qui pourra s’avérer utile pour le piégeage d’atomes.La seconde partie de cette thèse décrit un système développé à l’Institut d’Optique et comprenant des atomes neutres piégés dans des matrices de pinces optiques. Dans ce cas, nous excitons les atomes dans des états de Rydberg afin de bénéficier de fortes interactions interatomiques. Nous avons caractérisé les interactions de van der Waals et les interactions résonantes entre deux atomes individuels, et démontré le caractère cohérent de l’interaction dipolaire. Nous avons enfin simulé la dynamique d’une chaine élémentaire de spins dans une matrice de trois atomes / Most platforms that are being developed to build quantum simulators do not satisfy simultaneously all the requirements necessary to implement useful quantum tasks. Robust systems can be constructed by combining the strengths of multiple approaches while hopefully compensating for their weaknesses. This thesis reports on the progress made on two different setups that are being developed toward this goal.The first part of this thesis focuses on a hybrid system of neutral atoms coupled to superconducting qubits that is under construction at the University of Maryland. Sub-wavelength diameter optical fibers allow confining an ensemble of cold atoms in the evanescent field surrounding the fiber, which makes them ideal for placing atoms near a superconducting surface. We have developed a tapered fiber fabrication apparatus, and measured an optical transmission in excess of 99.95% for the fundamental mode. We have also optimized tapered fibers that can support higher-order optical modes with high transmission, which may be useful for various optical potential geometries.The second part of this thesis focuses on a system of neutral atoms trapped in arrays of optical tweezers that has been developed at the Institut d’Optique. Placing the atoms in highly excited Rydberg states allows us to obtain strong interatomic interactions. Using two individual atoms, we have characterized the pairwise interactions in the van der Waals and resonant dipole-dipole interaction regimes, providing a direct observation of the coherent nature of the interaction. In a three-atom system, we have finally simulated the dynamics of an elementary spin chain

Für die makroskopischen Eigenschaften und Funktionen biologisch relevanter Materie spielen schwache, intra- und intermolekulare Wechselwirkungen dispersiver und elektrostatischer Natur auf molekularem Niveau eine große Rolle. Um diese schwachen Wechselwirkungen zu untersuchen, können Modellsysteme, isoliert in der Gasphase, herangezogen werden. Benzoldimer, ein schwach gebundener Van der Waals Komplex, kann beispielsweise als Modellsystem für dispersive Wechselwirkungen dienen. In der vorliegenden Arbeit werden die strukturellen Eigenschaften und die (interne) Dynamik des Benzoldimers mit Hilfe spektroskopischer Methoden in den Energiebereichen der Rotationen, Vibrationen und elektronischen Übergänge untersucht und im Kontext der Symmetrie diskutiert. Die in dieser Arbeit vorgestellten Experimente tragen zu einem tieferen Verständnis des Benzoldimers bei, jedoch zeigt das Experiment zur internen Dynamik auch, dass eine ausreichende theoretische Beschreibung des Benzoldimers nach wie vor eine Herausforderung darstellt. Schwingungsübergänge hochsymmetrischer Moleküle sind oft optisch inaktiv, können jedoch mit der hier vorgestellten Methode der Symmetrieerniedrigung durch Komplexierung zugänglich gemacht werden, wie am Beispiel des Benzols demonstriert wird. Außerdem wird ein Mechanismus vorgstellt, der kollisionsinduzierte Konformationsänderungen in einem Molekularstrahl beschreibt. Dieses Modell kann generell für Molekularstrahlexperimente an flexiblen Molekülen hilfreich sein, einerseits um die beobachtete Konformationsverteilung zu verstehen, andererseits um die experimentellen Parameter gezielt zu verändern und somit Konformerpopulationen zu manipulieren. Die in dieser Dissertation vorgestellten spektroskopischen Experimente liefern einerseits molekülspezifische Informationen und ermöglichen andererseits, Modelle, die von allgemeiner Bedeutung sind, zu entwickeln. / The macroscopically observable properties and functionalities of biological matter are often determined by weak intra- and intermolecular interactions on the microscopic level. Such weak interactions are for example hydrogen bonding and van der Waals interactions and can be investigated best on isolated model systems in the gas phase. The benzene dimer, for example, is a prototype system to investgate dispersive interactions. The spectroscopic experiments, covering the energy ranges of rotations, vibrations and electronic transitions, presented in this thesis, contribute to a deeper understanding of the benzene dimer. However, from the experiments investigating the internal dynamics it becomes clear that an appropriate theoretical description of the benzene dimer is still a challenge. Vibrational transitions of highly symmetric molecules, as for example of the benzene, are often optically inactive. Here, a method is presented, which exploits symmetry reduction upon complexation and thus allows one to access such modes. Furthermore, a model is proposed describing collision induced conformational interconversion in a molecular beam. This model can be helpful for molecular beam experiments of flexible molecules to understand the observed relative conformational population and to adapt the experimental conditions allowing for the manipulation of the relative conformer abundances. In this thesis, results are presented that allow one on the one hand to deduce molecular specific information and that on the other hand also give a broader insight into phenomena of general importance.

The Casimir-Polder interaction between a single neutral atom and a nearby surface, arising from the (quantum and thermal) fluctuations of the electromagnetic field, is a cornerstone of cavity quantum electrodynamics (cQED), and theoretically well established. Recently, Bose-Einstein condensates (BECs) of ultracold atoms have been used to test the predictions of cQED. The purpose of the present thesis is to upgrade single-atom cQED with the many-body theory needed to describe trapped atomic BECs. Tools and methods are developed in a second-quantized picture that treats atom and photon fields on the same footing. We formulate a diagrammatic expansion using correlation functions for both the electromagnetic field and the atomic system. The formalism is applied to investigate, for BECs trapped near surfaces, dispersion interactions of the van der Waals-Casimir-Polder type, and the Bosonic stimulation in spontaneous decay of excited atomic states. We also discuss a phononic Casimir effect, which arises from the quantum fluctuations in an interacting BEC. / Die durch (quantenmechanische und thermische) Fluktuationen des elektromagnetischen Feldes hervorgerufene Casimir-Polder-Wechselwirkung zwischen einem elektrisch neutralen Atom und einer benachbarten Oberfläche stellt einen theoretisch gut untersuchten Aspekt der Resonator-Quantenelektrodynamik (cavity quantum electrodynamics, cQED) dar. Seit kurzem werden atomare Bose-Einstein-Kondensate (BECs) verwendet, um die theoretischen Vorhersagen der cQED zu überprüfen. Das Ziel der vorliegenden Arbeit ist es, die bestehende cQED Theorie für einzelne Atome mit den Techniken der Vielteilchenphysik zur Beschreibung von BECs zu verbinden. Es werden Werkzeuge und Methoden entwickelt, um sowohl Photon- als auch Atom-Felder gleichwertig in zweiter Quantisierung zu beschreiben. Wir formulieren eine diagrammatische Störungstheorie, die Korrelationsfunktionen des elektromagnetischen Feldes und des Atomsystems benutzt. Der Formalismus wird anschließend verwendet, um für in Fallen nahe einer Oberfläche gehaltene BECs Atom-Oberflächen-Wechselwirkungen vom Casimir-Polder-Typ und die bosonische Stimulation des spontanen Zerfalls angeregter Atome zu untersuchen. Außerdem untersuchen wir einen phononischen Casimir-Effekt, der durch die quantenmechanischen Fluktuationen in einem wechselwirkenden BEC entsteht.

No description available.