ZnO nanoparticles in the size range 2.5–7 nm have been synthesised by a wet chemical method where ZnO particles were grown in basic zinc acetate solution. The optical band gap increases when the size of the particles decreases. An empirical relation between the optical band gap given from absorption measurements, and particle size given from XRD measurements has been developed and compared to other similar relations found in the literature.    Time resolved UV-Vis spectroscopy has been used to follow the growth of particles in situ in solution. The data show that the growth mechanism not can be described by a simple Oswald ripening approach and nor by an exclusive agglomeration of smaller clusters into larger particles. The growth mechanism is more likely a combination of the proposed reaction themes. The data also reveal that particle formation do not demand a heating step for formation of the commonly assumed initial cluster Zn4O(CH3COO)6.    Steady state fluorescence has been studied as a function of particle size during growth in solution. These measurements confirm what is found in the literature in that the visible fluorescence is shifted to longer wavelengths and loses in intensity as the particles grow. Some picosecond spectroscopy has also been done where the UV fluorescence has been investigated. From these measurements it is apparent that the lifetime of the fluorescence increases with particle size.     The phonon spectrum of ZnO has been studied with Raman spectroscopy for a number of different particle sizes. From these measurements it is clear that there is a strong quenching of the phonons due to confinement for the small particles, and the only clearly observed vibration is one at 436 cm-1 which intensity strongly increases with particle size.

A systematic study of trends in band gap and lattice energies for bare zinc oxide nanoparticles were performed by means of quantum chemical density functional theory (DFT) calculations and density of states (DOS) calculations. The geometry of the optimized structures and the appearance of their frontier orbitals were also studied. The particles studied varied in sizes from (ZnO)6 up to (ZnO)192.The functionalization of bare and hydroxylated ZnO surfaces with MPTMS was studied with emphasis on the adsorption energies for adsorption to different surfaces and the effects on the band gap for such adsorptions.

Co-doped ZnO (ZnO:Co) thin film with room temperature ferromagnetism and spin polarized carriers is one of the advance materials and highly applicable in future development in spintronics. When ZnO:Co films deposited by a £_ growth method in a ion sputtering system, low solubility of Co (3.75%) limits further applications such that a single-guns sputtering thin film growth technique is employed in this study to outreach this limitation. A ZnO:Co bulk with 5 at% of Co was formed by a solid reaction method and used as a target. ZnO:Co films were grown in a single-gun RF sputtering system. However, all films grown at room temperature were insulator which might because sufficient oxygen content in the target and the negative charge of oxygen ion moving toward substrate making the films of full oxygen content. In this study, the post annealing in vacuum environment and the deposition of films in hydrogenation environment are conducted to try to produce various level of oxygen vacancies in the films for understanding the interplay between the oxygen vacancies and the electric transport and magnetic coupling. The present experiment contains two parts: (1) grow films with various thicknesses by controlling deposition time and then applying post annealing process, and (2) grow the films in oxygen reduced environment by introducing hydrogen during growth and taking out partial oxygen content in the plasma and the films. In the first part, the grain sizes of the films are near constant while the crystal quality is improved with the thickness of films. The worse crystal quality of grains, the better the electric transport and the stronger the magnetic coupling after post annealing processes. This indicates that the electric transport and magnetic coupling could be improved when the thin films was formed by crystals with certain disordering and contained a certain level of oxygen vacancies. In the second part, the introduced hydrogen may combine with the oxygen sputtered out from the target before deposition on substrates. It means that the films are grown in oxygen deficient conditions and result in various degrees of oxygen vacancies. Zn clusters precipitate in films when the concentration of hydrogen is over 20%, and at the meantime, they increase the conductivity and suppress the magnetic coupling in the films. These discoveries provide new perspective in understand the electric transport and ferromagnetism mechanics in DMS materials.

Quasi one-dimensional (1D) nanostructures show great promise for many applications, including in solar cells, nanogenerators and chemical sensors, due to the high surface-to-volume ratio and unique properties of nanostructures. The growth of these nanostructures is commonly catalyzed by metal nanoparticles and generally attributed to the vapor-liquid-solid (VLS) mechanism. The purpose of this research is to better understand the role of the catalyst nanoparticles in the growth of 1D nanostructures, in order to allow improved control of the synthesis process. To this end, nanostructures were grown with a variety of compositions, including Au- and Sn-catalyzed ZnO, Au-catalyzed FexOy and Au-catalyzed Si nanostructures. The morphology of the nanostructures was characterized with electron microscopy, and the crystallographic orientation with X-ray texture analysis. The catalyst particles were further characterized with both in-situ and post-growth X-ray diffraction. The types of bonding in the source material and catalyst play a significant role in the diffusion path of the source material to the growth front and in the catalyst particle state during growth. Dissimilar bonding types in the source material and catalyst prevent bulk diffusion of the source material through the catalyst, thereby preventing eutectic melting of the catalyst. These results bring new insight into the catalyzed growth of 1D nanostructures and assist in the informed choice of appropriate catalyst materials, which may aid the utilization of 1D nanostructures in energy-related and other applications.

Piezoelectric materials are widely used for sensors, actuators and trasducers. Traditionally, piezoelectric applications are dominated by multicomponent oxide ferroelectrics such as lead zirconate titanate (PZT), which have the advantage of high piezoelectric coefficients. Recently, one-dimensional piezoelectric nanostructures such as nanowires of zinc oxide (ZnO) and gallium nitride (GaN) has gained a lot of attention due to their combined piezoelectric and semiconducting properties. The focus of this thesis is to study the processing and electric properties of such piezoelectric thin films and nanostructures for various applications. There is an increasing interest to form thin films of multicomponent ferroelectric oxides such as PZT on three-dimensional structures for charge storage and MEMS applications. Traditional vapor phase deposition techniques of PZT offer poor conformality over threedimensional surfaces due to their reactant transport mechanisms. As an alternative, solgel synthesis may provide new process possibilities to overcome this hurdle but the film quality is usually inferior, and the yield data was usually reported for small device areas. The first part of this study is dedicated to the characterization of the electric properties and yield of PZT thin film derived from the sol-gel process. PZT thin films with good electric property and high yield over a large area have been fabricated. La doping was found to double the breakdown field due to donor doping effect. LaNiO3 thin films that can be coated on a three-dimensional surface have been synthesized by an all-nitrate based sol-gel route, and the feasibility to form a conformal coating over a three-dimensional surface by solution coating techniques has been demonstrated. ZnO and GaN micro/nanowires are promising piezoelectric materials for energy harvesting and piezotronic device applications. The second part of this study is focused on the growth of ZnO and GaN micro/nanowires by physical vapor deposition techniques. The morphology and chemical compositions are revealed by electron microscopy. Utilizing the as-grown ZnO nanowires, single nanowire based photocell has been fabricated, and its performance was studied in terms of its response time, repeatability, excitation position and polarization dependence upon He-Cd UV-laser illumination. The excitation position dependence was attributed to the competition of two opposite photo- and thermoelectric currents originated from the two junctions. The excitation polarization dependence was attributed to the difference in optical properties due to crystallographic anisotropy. Employing the as-grown GaN nanowires, single nanowire based strain sensor is demonstrated, and its behavior is discussed in terms of the effect of strain-induced piezopotential on the Schottky barrier height.

The analysis and development of robust sensing platforms based on solidly-mounted ZnO bulk acoustic wave devices was proposed. The exploitation of acoustic energy trapping was investigated and demonstrated as a method to define active sensing areas on a substrate. In addition, a new "hybrid" acoustic mode experiencing acoustic energy trapping was studied theoretically and experimentally. This mode was used as an explanation of historical inconsistencies in observed thickness-shear mode velocities. Initial theoretical and experimental results suggest that this mode is a coupling of thickness-shear and longitudinal particle displacements and, as such, may offer more mechanical and/or structural information about a sample under test. Device development was taken another step further and multi-mode ZnO resonators operating in the thickness-shear, hybrid, and longitudinal modes were introduced. These devices were characterized with respect to sample viscosity and conductivity and preliminary results show that, with further development, the multi-mode resonators provide significantly more information about a sample than their single-mode counterparts. An alternative to resonator-based platforms was also presented in the form of bulk acoustic delay lines. Initial conceptual and simulation results show that these devices provide a different perspective of typical sensing modalities by using properly designed input pulses, device tuning, and examining overall input and output signal spectra.

A sensor is a technological device or biological organ that detects, or senses, a signal or physical condition and chemical compounds. Technological developments in the recent decades have brought along with it several environmental problems and human safety issues to the fore. In today's world, therefore, sensors, which detect toxic and inflammable chemicals quickly, are necessary. Gas sensors which form a subclass of chemical sensors have found extensive applications in process control industries and environmental monitoring. The present thesis reports the attempt made in development of Zinc oxide thin film based gas sensors. ZnO is sensitive to many gases of interest like hydrocarbons, hydrogen, volatile organic compounds etc. They exhibit high sensitivity, satisfactory stability and rapid response. In the present work the developed sensors have been tested for their sensitivity for a typical volatile organic compound, acetone. An objective analysis of the various substrates namely borosilicate glass, sintered alumina and hard anodized alumina, has been performed as a part of this work. The substrates were evaluated for their electrical insulation and thermal diffusivity. The microstructure of the gas sensitive film on the above mentioned substrates was studied by SEM technique. The gas sensitive Zinc oxide film is deposited by D.C reactive magnetron sputtering technique with substrate bias arrangement. The characterization of the as-deposited film was performed by XRD, SEM and EDAX techniques to determine the variation of microstructure, crystallite size, orientation and chemical composition with substrate bias voltage. The thesis also describes the development of the gas sensor test setup, which has been used to measure the sensing characteristics of the sensor. It was observed that the ZnO sensors developed with higher bias voltages exhibited improved sensitivity to test gas of interest. Gas sensors essentially measure the concentration of gas in its vicinity. In order to determine the distribution of gas concentration in a region, it is necessary to network sensors at remote locations to a host. The host acts as a gateway to the end user to determine the distribution of gas concentration in a region. However, wireless gas sensor networks have not found widespread use because of two inherent limitations: Metal oxide gas sensors suffer from output drift over time; frequent recalibration of a number of sensors is a laborious task. The gas sensors have to be maintained at a high temperature to perform the task of gas sensing. This is power intensive operation and is not well suited for wireless sensor network. This thesis reports an exploratory study carried out on the applicability of gas sensors in wireless gas sensor network. A simple prototype sensing node has been developed using discrete electronic components. A methodology to overcome the problem of frequent calibration of the sensing nodes, to tackle the sensor drift with ageing, is presented. Finally, a preliminary attempt to develop a strategy for using gas sensor network to localize the point of gas leak is given.

This thesis deals with the investigations on the nonlinear electrical and manganetotransport properties of polycrystalline multi-phase ceramic composites of Zno/pervoskite manganite. Multifunctional properties are studied such as the enhanced low-field magnetoresistance(LFMR). magnetically tuneable low-voltage nonlinear current-voltage (I-V) characteristics with larger nonlinearity coefficients suitable for semiconducting and magnetoelectric devices. A brief introduction on the structure-property correlations, electronic and magnetic structures, nonlinear electrical conduction, phase separation, grain size and grain boundary effects on transport properties of manganites are presented. The nonlinear current-voltage characteristics of ZnO based varistors are also summarized. The thesis describes the synthesis of the ceramics and the methodology of different techniques utilized in characterizing the samples. The phase conversions in calcium manganite with changing Ca/Mn ratios as well as the oxygen non-stoichiometry and their influence on electrical transport properties were studied. The realization of low-voltage varistors prepared from ZnO+ CaMnO3 ceramic composites was described. An energy band model consisting of n-p-n heterojunctions of n-ZnO1-γ:Mn/p-CMZO/n-ZnO1 γ:Mn has been proposed in order to explain the large nonlinearity coefficients obtained at low field-strengths of 1.8 to 12 V/mm. The detailed investigationos on the structural identification and physico-chemical analyses of Ca4Mn7Zn3O21-δ(CMZO) phases having the beta-alumina or magnetoplumbite-type structures were carried out. The thesis also embodies the magnetically tuneable nonlinear I-V characteristics and the magnetotransport properties of ZnO/La(Sr)MnO3 and ZnO/La(Ca,Sr)MnO3 ceramic composites. The present investigations demonstrate that the ferromagnetic insulating (FMI) La06 Sr04Mn1-yZnyO3(y = 3 to 8 at.%) when present as minor phase in ZnO1- γ:Mn ceramics enables in attaining magnetically tunealbe nonlinear I-V characteristics. Wherein, the dominant ZnO1- γ:Mn phase remains paramagnetic. The results also indicate that the prevalence of ferromagnetism in ZnO1-γ:Mn is not significant for realizing magnetically tuneable I-V curves. The controversial results related to the existence of ferromagnetism in ZnO(doped)leading to diluted magnetic semiconductors(DMS) have been investigated. Another novel aspect of the present work is the low-field magnetoresistive(LFMR) property of ZnO/La(Sr)MnO3 and ZnO/La(Ca.Sr)MnO3 ceramic composites which been explained on the basis of spin-polarised tunneling across the intergrain regions. The influence of Zn2+ as a diamagnetic substitutent in modifying the crystallographic phase content, electrical transport and magnetic properties of Lao6Sro4MnO3 were studied in detail. The results point towards the fact the large decrease of Tc and Ms at lower Zn contents(≤ 8 at.%)is due to the dominant role played by the excess oxygen vacancy (Vo) as an electron donor in p-type Lao6Sro4Mn1-yZnyO3-δ rather than the charge compensatively predictable values. The modifications of electronic and magnetotransport properties were carried out on Lao6Sro4MnO3 substituted with diamagnetic ions such as Mg2+ - Al3+ - Ti4+ - Nb5+ - Mo6+ or W6+ at Mn-sublattice. The TEM studies including HREM results point to the fact the large ΔT(= Tc-TM-1)is accountable in terms of charge conduction within the electronically heterogeneous phase mixtures of charge ordered insulating (CO1) bi-stripes prevailing within the charge disordered FMI phases.

Sensors is one of the major areas of current research. Thin film micro/nano sensors are gaining attention worldwide, as there is necessity of miniaturization. There are varieties of sensors available by utilizing different materials in bulk and thin film form for measuring parameters like temperature, pressure, flow, humidity etc. Apart from these, there are various sensors available to measure impact force. Impact sensor offers potential application possibilities in robotics, aerospace, structural & mechanical engineering and related areas. Many physical principles have been explored for the realization of impact sensor. The present thesis reports the efforts made in developing impact sensor using piezoelectric thin film. The necessary brief background information on impact sensors is presented in Chapter 1. This includes the description of available literature on impact sensors and their probable applications. In Chapter 2, a review of the various techniques such as thin film deposition techniques, film thickness measurement techniques, thin film characterization techniques, used in our work are explained in detail. Chapter 3 explains the direct and indirect methods of characterization used for confirming the piezoelectric property of zinc oxide thin films. The detailed experimental work carried out in realizing the impact sensor using piezoelectric thin films is presented in chapter 4. This includes design of the sensor, calibration setup used & the procedure followed and results obtained. Finally, we present the summary of the work carried out in the thesis, conclusions arrived at and the scope for carrying out further work in the direction of making the sensor more efficient.

Solid state lighting is a new environmentally friendly light source. So far, light emitting diodes (LEDs) and organic LEDs (OLEDs) have been presented as candidates with potentially high efficiency. Recent advances of OLEDs in device architecture, light-out coupling, and materials have ensured high efficiency, exceeding that of incandescent light bulbs. In contrast to conventional point source LEDs, OLEDs distribute light throughout the surface area and are not restricted by their size. Additionally, OLEDs are expected to reach sufficient stability in the near future. The remaining challenge for OLEDs is their cost. New OLED technologies provide cost effective manufacturing methods which could be presented for transparent electrode materials because indium tin oxide (ITO), a widely used material as a transparent electrode for OLEDs, is less than optimal due to its high element price. In this work, alternative transparent electrodes for OLEDs as a replacement of ITO were studied. First, Al doped ZnO (ZnO:Al) which is composed of abundant materials was investigated with DC magnetron sputtering under a wide range of experimental conditions. The optimised ZnO:Al received comparable performance with conventional ITO films, low sheet resistance of 22.8 Ω/sq as well as a high transparency of 93.1 % (average value in the visible range). Various type of p-i-n OLEDs were employed on the structured ZnO:Al using photolithography. Green OLEDs with double emission layers have been archived stable efficiencies even at higher luminance. Also, OLEDs using two fluorescent colour system on ZnO:Al anode showed a purely white emission. It has been found that the OLEDs on ZnO:Al anode has comparable or better device efficiencies and operational lifetime compared to OLEDs on conventional ITO anode. As another alternative electrode, the conductive polymer Baytron®PH510 (PEDOT:PSS) was investigated. Due to a relatively high sheet resistance of PEDOT:PSS, metal grid was designed for large size OLEDs. White OLEDs on PEDOT anode with a size of 5 × 5 cm2 have achieved more than 10 lm/W of power efficiency using a scattering foil. Furthermore, up-scaled devices on 10 × 10 cm2 were also demonstrated. These results showed ZnO:Al and PEDOT are suitable for OLEDs as anode and have high potential as alternative transparent electrode materials.