The use of insulated-gate bipolar transistor (IGBT)-based power converters is increasing exponentially. This is due to high performance of these devices in terms of efficiency and switching speed. However, due to the switching action, high frequency electromagnetic interference (EMI) noises are generated. Design of a power converter with reduced EMI noise level is one of the primary objectives of this research. The first part of the work focuses on designing common-mode (CM) filters, which can be integrated with differential-mode (DM) filters for three-phase pulse-width modulation (PWM) rectifier-based motor drives. This work explores the filter design based on the CM equivalent circuit of the drive system. Guidelines are provided for selection of the filter components. Different variants of the filter topology are evaluated to establish the effectiveness of the proposed topology. Analytical results based on Bode plot of the transfer functions are presented, which suggest effective EMI reduction. Experimental results based on EMI measurement on the grid side and CM current measurement on the motor side are presented. These results validate the effectiveness of the filter. In the second part of the work, it is shown that inclusion of CM filters into DM filters results in resonance oscillations in the CM circuit. An active damping strategy is proposed to damp the oscillations in both line-to-line and line-to-ground ac voltages and currents. An approach based on pole placement by state feedback is used to actively damp both the DM and CM filter oscillations. Analytical expressions for state-feedback controller gains are derived for both continuous-and discrete-time models of the filter. Trade-off in selection of the active damping gain on the lower-order grid current harmonics is analysed using a weighted admittance function method. In the third part of the work, single-phase grid-connected power converters are considered. An integrated CM filter with DM LCL filter is proposed. The work explores the suitability of PWM methods for single-phase and parallel single-phase grid-connected power converters. It is found that bipolar PWM and unipolar PWM with 180◦interleaving angle are suitable for single-phase and parallel single-phase power converters, respectively. The proposed configuration along with the PWM methods reduces the CM voltage, CM current, and EMI noise level effectively. It is also shown that the suggested circuit is insensitive to nonidealities of the power converter such as dead-time mismatch, mismatch in converter-side inductors, unequal turn on and turn off of the switches, and propagation delays. In the fourth part of the work, the inter-phase inductor in parallel interleaved power converters is integrated with LCL filter boost inductor. Different variant designs are presented and compared with the proposed structure. It is shown that the proposed structure makes use of standard core geometries and consumes lesser core material as well as copper wire. Hence, it reduces the overall size and cost of the power converter. In the present work, a 10kVA three-phase back-to-back connected with input LCL filter and output dv/dt filter, a 5kVA single-phase grid-connected power converter with LCL filter, and a 7.5kVA parallel single-phase grid-connected power converter with LCL filter are fabricated in the laboratory to evaluate and validate the proposed methods. The experimental results validate the proposed methods that result in significant EMI performance improvement of grid-connected power converters.

Les composants magnétiques en technologie planar répondent aux exigences actuelles de l’Electronique de Puissance (EP), à savoir la montée en fréquence de commutation des structures d’EP et la réduction du volume des convertisseurs. La première tendance impose des contraintes fortes en termes de compatibilité électromagnétique (CEM) des équipements. Ces dernières doivent être prises en compte par les ingénieurs dès la phase conception des convertisseurs en se basant sur des modèles fiables, peu développés pour les composants planar dans la littérature scientifique. Ce travail de thèse porte ainsi sur la modélisation des composants planar pour applications aux filtres CEM. Différentes méthodes sont développées au cours de cette thèse pour arriver à évaluer de manière fine les éléments parasites des inductances planar de mode commun : capacités parasites et inductances de fuite. Une partie du travail a porté sur la modélisation par circuits équivalents du comportement fréquentiel des inductances de MC. Une approche automatisée, basée sur un algorithme de fitting a ainsi été développée pour élaborer des circuits équivalents fiables et robustes. Des approches analytiques (Décomposition du Champ Electrique) et semi-analytiques (Fonctions de Green) ont aussi été proposées pour évaluer les valeurs des éléments parasites. La dernière partie de la thèse est plus orientée conception, avec la réalisation de deux structures de composants innovantes, la première se basant sur une technique de compensation des capacités parasites à l’aide d’éléments parasites structuraux et la seconde sur l’association de deux noyaux magnétiques, possédant matériaux et géométries différentes / The magnetic components with planar technology join in the current trends in Power Electronics (PE), namely increasing the switching frequency of PE structures and reducing the size of the power converters. The first tendency imposes strong constraints in terms of electromagnetic compatibility of equipments. The latter has to be considered by engineers at the beginning of the design of Power converters on the basis of reliable models, which are not sufficiently developed for planar components in scientific literature. This PhD work thereby focuses on the modeling of planar components for the applications of EMI filters. Different methods are developed during this study in order to accurately evaluate the parasitic elements of planar common-mode chokes: parasitic capacitances and leakage inductances. A part of this dissertation concerns the equivalent circuit modeling of the frequency behavior of CM chokes. An automated approach, based on a fitting algorithm developed for elaborating reliable and robust equivalent circuits. Analytical approaches (Electric Field Decomposition) and semi-analytical (Green’s Function) are proposed as well for calculating the values of these parasitic elements. The last part of this dissertation is oriented to conception, with the realization of two structures of innovative components, the first one based on a parasitic capacitance cancellation technique using structural parasitic elements and the second one on the association of two magnetic cores with different materials and geometries

Depuis une bonne dizaine d'année, l'aéronautique a entamé sa mutation vers le "plus électrique".L'objectif étant de réduire la consommation de carburant, une des contraintes majeures de ces nouvelles solutions est de réduire la masse embarquée. Les filtres dimensionnés pour les convertisseurs statiques doivent donc être optimisés au mieux vis-à-vis de ce critère, ainsi que du volume. Il y a donc un fort besoin du côté des concepteurs d’avions de savoir quels choix parmi les différentes possibilités technologiques sont optimaux, et de connaître l'impact de ces choix sur le poids, le coût global et le volume de l'équipement. Le filtre CEM représente généralement environ 30% du coût et du volume d'un convertisseur électronique de puissance. Il va de soi que le volume et/ou la masse de ces filtres doit être optimisé. L'impact de la loi de commande du convertisseur, le choix des semi-conducteurs, du packaging, câbles (longueur et intégration dans l’avion), des machines électriques,...doivent être parfaitement connus pour atteindre un dimensionnement optimal.Dans cette perspective, les objectifs de ces travaux de thèse visent à fournir non seulement une démarche méthodologique pour la modélisation haute fréquence des variateurs de vitesse dédiés aux applications aéronautiques mais aussi une approche de dimensionnement par optimisation des filtres CEM. Pour cela, un outil logiciel évolutif d’aide à la génération rapide des modèles CEM est proposé. Une description modulaire et une mise en équation automatique du modèle fréquentiel complet ainsi que des gradients en facilitent l'utilisation en procédures d’optimisation sous contraintes. L’approche présentée dans ces travaux est relativement générique : la topologie du filtre, de la structure du convertisseur, du câblage et la loi de commande peuvent être facilement recalculées, grâce à cet environnement logiciel. / The More Electrical Aircraft concept is very promising regarding energy saves, but generates new problems, and especially the emergence of new power electronics loads on the electrical network. Keeping the same level of safety in the aircraft means developing these switching mode converters in accordance with the aircraft standards, as the DO160. This is not obvious since weights of equipments are especially constrained: indeed, the objective of weight and energy save needs to be balanced with the additional weight and volume of the required EMI filters. There is thus a strong need in helping the aircraft designers to choose among the various technological possibilities, and to know the impact of these choices on the global weight, cost and volume of the embedded equipments. The EMI filter usually represents roughly 30% of the cost and volume of a power electronics converter, and it is very important to optimize it. The impact of the converter control law, semiconductors choice, interconnects realization, harness selection and placement, electrical motors characteristics… should be perfectly known in order to reach a good system design. In this perspective, the objectives of this thesis are to provide not only an approach for modelling high frequency variable speed drives dedicated to aerospace applications but also a methodology to optimize the required EMI filters. For this purpose, new architecture software dedicated to the rapid generation of EMC models is proposed. A modular description and a complete automatic model generation facilitate the use by the designer in optimization procedures thanks to automatic gradient computation.The methodology presented in this work is not specifically developed for a given application. It is a very generic approach: the topology of the filter, the structure of the inverters, interconnects and the control law can be easily recalculated, using this software environment. Consequently, the impact of all these elements on the electromagnetic disturbances can be characterized, and the EMI filter optimized.

The brushed DC motor is a source of electromagnetic emission that may cause interference. The main issues with brushed DC motor are arcing, which occurs between the brushes and commutator, and inrush current. It is possible to decrease the electromagnetic emissions by addressing the source (brushed dc motor) and the installation. The source may be addressed by using filters in the form of X2Y-capacitors on the terminals or ferrites on the cables. The installation does not produce any emission, but it is possible to lower its contribution. This is done by altering the installation like changing the placement of cables and provide good coupling. An effective way of decreasing inrush currents is by using negative-thermal-coefficient (NTC) thermistors. Another measure to improve the EMC properties of the brushed DC motor is to design the motor so that it can trap EM emissions. Some of these parameters are motor house material, end-cap material, vent holes or slots on motor housing, placement of power terminals, crimping tabs and motor enclosure.

The thesis deals about method of gain signals from strain gauge bridges. There are mentioned some signal conditioning methods for bridges amplifiers and charactered their properties. In the next part of this thesis are calculated the amplifier errors for various temperature. There are projected individual variants of strain gage amplifiers (instrumentation amplifier AD524, isolation amplifier, switched capacitor based instrumentation amplifier), their properties are compared with strain gage amplifier Vishay P-3500.

Le travail de cette thèse apporte une contribution aux méthodes de réglage de la tension dans les réseaux électriques. Il s’agit de fournir au réseau la puissance active et surtout la puissance réactive nécessaire pour réguler la tension et aboutir à un système équilibré vue du côté source. Ces puissances sont extraites d’une source d’energie renouvelable : une attention particulière a été portée à l’énergie éolienne raccordée au réseau à travers la Machine Asynchrone à Double Alimentation (MADA) pilotée par des convertisseurs statiques. Le système de contrôle le plus répandu des éoliennes est basé principalement sur la technique d’extraction du maximum de puissance. Cependant, cette technique limite la mise en oeuvre deservices auxiliaires, telle que la participation des éoliennes au réglage de la tension dans le réseau électrique. Pour cela, une nouvelle méthode d’extraction du coefficient de puissance optimal, permettant d’améliorer la participation de la MADA à la régulation de la tension dans le réseau (compensation de la puissance réactive et du déséquilibre), a été développée. Le convertisseur multiniveaux à structure NPC (Neutral Point Clamped) raccordant l’énergie renouvelable au réseau a été étudié. La commande prédictive assurant simulatnément l’amélioration du facteur de puissance, l’équilibrage du réseau électrique et du bus continu du convertisseur NPC a été proposée. Ensuite, l’application de cette commande prédictive a été elargie en lui attribuant plusieurs objectifs : amélioration du facteur de puissance avec équilibrage du réseau, équilibrage du bus continu, minimisation des pertes par commutation et réduction de la tension de mode commun. La minimisation des pertes a été obtenue en proposant une nouvelle stratégie qui consiste à exploiter les datasheets constructeurs donnant l’évolution de l’énergie dissipée durant la commutation en fonction du courant. Ces courbes expérimentales ont été transformées en modèlesmathématiques implémentés dans la commande prédictive. Les résultats de simulation et expérimentaux sont présentés pour évaluer les performances de la méthode proposée. / The work in this research thesis presents a contribution to voltage regulation in electrical networks. By considering adequate active and reactive powers injection into the grid, voltage control and load balancing are provided. These powers are generated from a grid connected renewable energy conversion system : a special attention was paid to the Wind Energy ConversionSystem (WECS) based on Doubly-Fed Induction Generator (DFIG).The typical control strategy for WECS is the maximum power coefficient tracking method. However, this method limits desirable ancillary power services, such as the participation of wind turbines in voltage regulation in the power grid. Therefore, a new method that derives the optimal power coefficient enhancing the participation of WTS in voltage regulation in the network (reactive and unbalanced power compensation), has been developed. The multilevel NPC (Neutral Point Clamped) converter, used for grid interface connection of renewable energy sources systems, has been studied. A predictive control method for the three-level NPC converter, capable of simultaneously compensating the problems of : DC link capacitors voltage balancing, load balancing and power factor correction in the power system, has been proposed. Then, the application of this predictive control was extended to simultaneously achieve multiple objectives: load balancing with power factor correction in the network, DC link capacitors voltage balancing, switching losses minimization and common mode voltage reduction. The switching losses minimization was obtained by proposing a new strategy which consists on exploiting the manufacturer datasheets that gives the evolution of the switching loss energy in function of the circulating current. The experimental curves of the datasheet are expressed in a mathematical model implemented in the predictive control. Simulation and experimental results are presented to evaluate the performance of the proposed method.

La charge d’un véhicule électrique constitue un enjeu stratégique pour les constructeurs automobile et forme un réel défi à relever avant de pouvoir comparer ces véhicules à la simplicité d'usage du véhicule thermique. En effet, l’autonomie limitée, la durée de recharge de la batterie, le coût du déploiement d’une infrastructure de charge rapide, l'impact significatif sur les réseaux électriques et le coût élevé de la batterie sont à l’origine de plusieurs projets de recherche axés sur l’optimisation de la chaîne de recharge du véhicule électrique. Afin d’améliorer l'autonomie d'un véhicule électrique, une solution contraignante mais stratégique consiste à embarquer le chargeur dans le véhicule afin d’assurer la conversion ac-dc de l’énergie à partir des prises de courant. Cette solution permet d’augmenter la disponibilité de la charge pour les utilisateurs. En outre, le chargeur embarqué peut réutiliser tout, ou une partie des éléments déjà existants et nécessaires à la propulsion du véhicule. L'idée étant de pouvoir employer certains éléments de la chaîne de traction électrique, déjà embarqués dans le VE (moteur électrique et onduleur de tension), et d’ajouter un filtre d'entrée et un redresseur afin de concevoir le chargeur. Cette solution permet de réduire le coût du chargeur, sa taille ainsi que le volume nécessaire à l'intégration de ses constituants électriques, on parle alors de chargeur intégré à la chaîne de traction. Cependant, la réutilisation de l’électronique de puissance embarquée engendre des problèmes de compatibilité électromagnétique avec d’autres équipements connectés sur le réseau électrique et aussi avec les dispositifs de protection domestique.Le problème majeur à lever est donc, la limitation des émissions conduites et plus particulièrement des courants de mode commun dans une gamme de fréquence importante. Ce projet de thèse a donc, pour objectif, l’amélioration de la disponibilité de la charge actuelle tout en réduisant le volume du filtre CEM passif. Nous cherchons, à travers ces travaux, à identifier des domaines d'améliorations possibles, à proposer des solutions à bas coûts et à intégrer des modifications au niveau de la commande et de la topologie afin d'optimiser le comportement CEM, tant en basses fréquences (0 - 2 kHz) qu’en hautes fréquences (150 Hz- 30 MHz), de ce chargeur embarqué intégré sans isolation galvanique. Les propositions doivent répondre simultanément aux besoins de recharge domestique en monophasé (à 3.7 kW et à 7.4 kW) et rapide en triphasé (à 22 kW et à 43 kW) sans pour autant augmenter le volume ni les coûts engendrés. Ainsi, cinq axes de travail sont étudiés: l’optimisation du comportement CEM (0-2 kHz) du chargeur en monophasé ; l’optimisation du comportement CEM (0-2 kHz) du chargeur en triphasé ; le développement, la mise en œuvre et l’instrumentation de deux bancs expérimentaux exploités pour l’obtention de résultats; la proposition d’une approche de modélisation CEM de la structure qui tient compte du mode commun et du mode différentiel ; et la proposition de solutions pour la réduction des émissions conduites (150 kHz – 30 MHz). / Battery chargers for electric vehicles are classified as on-board or off-board chargers. Off-board chargers are not constrained by size or weight but introduce additional cost to the infrastructure through the deployment of a high number of charging stations. In order to meet the needs of electric vehicle users in terms of charging availability, on-board chargers that achieve ac/dc conversion are retained. Furthermore, on-board chargers are classified as standalone or integrated systems. By reusing parts of the traction power train for charging, the latter reduces the cost of the charger. Disadvantages of integrated systems include electromagnetic compatibility issues and complex control schemes.This work presents the power quality performance analysis and control optimization of an on-board non-galvanically isolated electric vehicle charger integrated to the traction’s power train. In order to be able to evaluate the high frequency conducted common mode emissions (150 kHz - 30MHz) of a power conversion structure, one needs to develop a good current control scheme that establishes a high-quality low frequency behavior (0 - 2 kHz). Therefore, different aspects related to the power factor correction of the single-phase as well as the three-phase charging configurations are studied: the control scheme for the regulation of the charging power, the displacement power factor correction, the suppression of the grid current harmonics and the active damping of the input filter’s resonance. Two experimental test benches are developed using two different technologies (Silicon IGBTs vs. Silicon Carbide Mosfets). Experimental results are provided.This work also presents a comprehensive approach to modeling the CM and the DM EMI behavior of a power electronics structure. This method is applied to the charger in its single-phase and three-phase configurations. The models allow to evaluate the fluctuating internal nodes and to study the effect of various proposed mitigation solutions on the CM emissions. The models are also developed in the intent of being injected into optimization algorithms for the future design of an optimal EMI filter.

Wide bandgap (WBG) semiconductor devices are becoming increasing popular in power electronics applications. However, WBG semiconductor devices generate a substantial amount of conducted electromagnetic interference (EMI) compared to silicon (Si) devices due to their ability to operate at higher switching frequencies, higher operating voltages and faster slew rates. This thesis explores and analyzes EMI mitigation techniques that can be applied to a power module architecture at the packaging level. In this thesis, the EMI footprint of four different module architectures is measured experimentally. A time domain LTspice simulation model of the experimental test setup is then built. The common mode (CM) EMI emissions that escape the baseplate of the module into the converter is then examined through the simulation. The simulation is used to explore the CM noise footprint of eight additional module architectures that were found in literature. The EMI trends and the underlying mitigation principle for the twelve modules is explained by highlighting key differences in the architectures using common mode equivalent modelling and substitution and superposition theorem. The work aims to help future module designers by not only comparing the EMI performance of the majority of module architectures available in literature but by also providing an analysis methodology that can be used to understand the EMI behavior of any new module architecture that has not been discussed. Although silicon carbide (SiC) modules are used for this study, the results are applicable for any WBG device. / M.S. / As society moves towards the electric grid of the future, there have been increasing calls for high efficiency, high power density, and low electromagnetic interference (EMI) power electronic converters. EMI is a big problem when using wide-bandgap (WBG) devices as these devices can switch very quickly and handle higher voltages when compared to silicon devices. In this study, ways to reduce EMI in a WBG power module through twelve different types of packaging are explored. Four WBG power modules are designed and fabricated in the lab, whereas a simulation model was created to study the EMI behavior of the remaining eight power module. The EMI behavior of these modules is explained using common mode (CM) equivalent modeling and substitution and superposition theorem. This study is important because WBG devices are becoming more and more popular in power electronic applications. The author hopes the findings and analysis presented in this paper can help future module designers reduce the EMI footprint of modules they design.

Triple modular redundancy (TMR) with repair is commonly used to improve the reliability of systems. TMR is often employed for circuits implemented on field programmable gate arrays (FPGAs) to mitigate the radiation effects of single event upsets (SEUs). This has proven to be an effective technique by improving a circuit's sensitive cross-section by up to 100x. However, testing has shown that the improvement offered by TMR is limited by upsets in single configuration bits that cause TMR to fail.This work proposes a variety of mitigation techniques that improve the effectiveness of TMR on FPGAs. These mitigation techniques can alter the circuit's netlist and how the circuit is placed and routed on the FPGA. TMR with repair showed a neutron cross-section improvement of 100x while the best mitigation technique proposed in this work showed an improvement of 700x.This work demonstrates both some causes behind single bit SEU failures for TMR circuits on FPGAs and mitigation techniques to address these failures. In addition to these findings, this work also shows that the majority of radiation failures in these circuits are caused by multiple cell upsets, laying the path for future work to further enhance the effectiveness of TMR on FPGAs.

The growth in the number of wireless devices and applications underscores the need for characterizing and mitigating interference induced problems such as distortion and blocking. A typical interference scenario involves the detection of a small amplitude signal of interest (SOI) in the presence of a large amplitude interfering signal; it is desirable to attenuate the interfering signal while preserving the integrity of SOI and an appropriate dynamic range. If the frequency of the interfering signal varies or is unknown, an adaptive notch function must be applied in order to maintain adequate attenuation. This work explores the performance space of a phase cancellation technique used in implementing the desired notch function for communication systems in the 1-3 GHz frequency range. A system level model constructed with MATLAB and related simulation results assist in building the theoretical foundation for setting performance bounds on the implemented solution and deriving hardware specifications for the RF notch subsystem devices. Simulations and measurements are presented for a Low Noise Amplifer (LNA), voltage variable attenuators, bandpass filters and phase shifters. Ultimately, full system tests provide a measure of merit for this work as well as invaluable lessons learned. The emphasis of this project is the on-wafer LNA measurements, dependence of IC system performance on mismatches and overall system performance tests. Where possible, predictions are plotted alongside measured data. The reasonable match between the two validates system and component models and more than compensates for the painstaking modeling efforts. Most importantly, using the signal to interferer ratio (SIR) as a figure of merit, experimental results demonstrate up to 58 dB of SIR improvement. This number represents a remarkable advancement in interference rejection at RF or microwave frequencies.