Matrix Assisted Laser Desorption Ionization–Time of Flight (MALDI-TOF) mass spectroscopy is used in the characterization of synthetic polymers. MALDI allows for determination of: modal, most probable peak (M P), molecular number average (MN), molecular weight average (MW), polydispersity (PD), and polymer spread (PSP). We evaluate a new sample preparation method using Induction Based Fluidics (IBF) to kinetically launch and direct nanoliter volumes to a target without contact. IBF offers signal improvement via field enhanced crystallization. This is the first study to discuss filed enhanced crystallization in MALDI sample preparation. IBF can increase signal/noise (S/N) and signal intensity for polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(ethylene glycol) (PEG) across a mass range of 2,500 to 92,000 Da showing more accurate PSP. Increases in S/N range up to: 279% for PS, 140% for PMMA, and 660% for PEG. Signal intensities increased up to: 438% for PS, 115% for PMMA, and 166% for PEG. Cross-polarization microscopy indicates dramatic morphology differences between IBF and micropipette. Finally, we speculate as to why IBF nanoliter depositions afford higher S/N values in experiments conducted in different instrumental configurations even without optimization. Next we sought to investigate whether nanoliter volumes of concentrated polar liquids and organic monomers launched to targets using IBF can be verified through the real time charge measurements. We show that using a nanoliter IBF dispensing device and nanocoulomb meter, charge measurements made on nanoliter drops in real time are correlated with the droplets surface area following Gauss’s Law. We infer the "induction only" formation of the double layer showing the ability to determine nanoliter volumes, nearly instantaneously, in real time. Implications are presented from these IBF measurement observations on improving/monitoring MALDI quantitation and its quality control. Polymer-dye interactions were further investigated using PMMA composites made from a polar metalloporphyrin [5-(4',4',5',5'-tetramethyl[1',3',2']dioxaborolan-2'-yl)-10,20-diphenylporphyrinato]zinc(II) (Zn(II)Bpin-DPP) in select weight %s (wt%s). Fluorescence spectroscopy has revealed that the porphyrin was well dispersed within the composite. Differential Scanning Calorimetry (DSC) showed that porphyrin acted as an antiplasticizer raising the glass transition (Tg) from 105 °C to 123 °C. Dielectric Analysis (DEA) was performed in the frequency range of 0.3 Hz to 100 kHz between -150 to 270 ⁰C. Permittivity (ε’), loss factor (ε’’) and dielectric response of beta (β), alpha beta (αβ), and conductivity relaxations were studied. Previous DEA data was limited to 190 ⁰C. This study brings analysis to 270 ⁰C which is start point for the first part of PMMA degradation. Thus forwarding DEA can be used to evaluate PMMA degradation. The electric modulus formalism is used to reveal the β and conductivity relaxations. The apparent activation energies (Ea) for the molecular relaxations are presented. AC (ζAC) and DC (ζDC) conductivity are also evaluated. Tan delta (δ), dissipation factor, evaluated between 1 Hz to 100 kHz was shown to increase with porphyrin loading although locally affected by free volume restriction. Havriliak-Negami (H-N) equation was fit using the complex electric modulus (M*) modified form and was performed on the conductivity region 160 to 190 ⁰C and degradation region 190 to 270 °C. Relaxations above the Tg were proven to be conductivity relaxations using four proofs. This is the first study to investigate PMMA degradation DEA with the complex electric modulus, M*, revealing a unique occurrence of increasing central relaxation times (s-1) and reducing electric loss modulus (M") frequency maxima (Hz) after the degradation temperature of 220 ⁰C was reached supporting current literature of the first of a two part degradation process that proceeds via end chain scission.

Supercapacitors are well known for their improvised power density compared to batteries. Ongoing research is mainly focused on improving the energy density of supercapacitors by using different electrode material nanocomposites. The recent research has revealed that graphene (G)-polyaniline (PANI) nanocomposite could be a promising material for supercapacitor applications. The supercapacitor is also associated with self-leakage current regardless of any electrode material. The main objectives of the project are to: (i) synthesize highly fabricate supercapacitor based of G-PANI electrode; (ii) improve the energy density of supercapacitor by applying ultrathin monolayer/monolayers film electrode surface. It is crucial to either improve or retain the effective capacitance of the dielectric film. The dielectric material chosen is polyvinylidene fluoride (PVDF) due to its dielectric constant and electrochemical properties. Langmuir-Schaefer (LS) technique is used to deposit the PVDF film onto the substrate. The optical properties of electrode materials were measured by UV-vis spectrophotometer. The surface morphology of the fabricated electrode material has been investigated using scanning electron microscopic (SEM) and atomic force microscopic (AFM) studies. The supercapacitor with and without dielectric layer have been studied using cyclic voltammetry, charging and discharging, and electrochemical impedance techniques, respectively. The specific capacitance has been found to increase by application of one monolayer of PVDF film of G-PANI electrode. However, the LS film of PVDF does not show the minimization of leakage current but revealed an increase in the specific capacitance due to enhancement in surface area associated with the electrode besides PVDF is also an electrochemical active material. The electrochemical investigation of various layers of PVDF on G-PANI in symmetric and asymmetric supercapacitor configuration has been presented in thesis. The future scope of the project could be designing the electrode with various number of layers of dielectric material that could reduce the leakage current, and retaining the specific capacitance of G-PANI nanocomposite electrodes.

This work is motivated by the Variable Specific Impulse Magnetoplasma Rocket (VASIMR) experiment. This device uses a helicon antenna to generate a plasma inside a dielectric tube, which is radially confined and directed towards the rocket nozzle by an axial magnetic field. An ion cyclotron heating antenna further heats the ions, and a magnetic nozzle accelerates the plasma along the confining magnetic field as it leaves the rocket, ultimately allowing it to detach from the magnetic field and produce thrust. The experimental research presented here provides insight into the physical mechanisms of power flow in a helicon system by providing an overall system power balance in the form of heat flux measurements, and exploring changes in the heat fluxes in different parts of the system in response to varying operational parameters. An infrared (IR) camera measures the total heat flux into the dielectric tube surface, and axially scanned bolometer and UV photodiode probes measure the radial power loss from particles and radiation. Results from IR camera measurements on three different helicon systems are presented: the VASIMR VX-50 experiment, the VASIMR VX-CR experiment, and the University of Texas at Austin (UT) helicon experiment. These results demonstrate the development of the IR camera diagnostic for use on helicon systems of varying scale and geometry, and show reasonable agreement as to the fraction of input power lost to the dielectric tube walls. On the UT experiment, the results presented account for essentially all of the input power, providing a full system power balance. The data from all three experiments indicate that radial transport of ions to the interior wall is the dominant mechanism of power loss, with UV radiation contributing a small percentage. Additional experiments on the UT helicon explore energy and particle transport to the wall due to capacitive coupling of ions near the antenna. These experiments show clear damage to the dielectric tube surface directly under the antenna, due to physical plasma etching of the surface by bombarding ions that are accelerated into the wall by local electric fields from the antenna. / text

The continuous scaling of microelectronic devices requires high permittivity (high-k) dielectrics to replace SiO₂ as the gate material. HfO₂ is one of the most promising candidates but the crystallization temperature of amorphous HfO₂ is too low to withstand the fabrication process. To enhance the film thermal stability, HfO₂ is deposited using atomic layer deposition (ALD), and incorporated with various amorphizers, such as La₂O₃, Al₂O₃, and Ta₂O₅. The incorporation is achieved by growing multiple ALD layers of HfO₂ and one ALD layer of MO[subscript x] (M = La, Al, and Ta) alternately (denoted as [xHf + 1M]), and the incorporation concentration can be effectively controlled by the HfO₂-to-MO[subscript x] ALD cycle ratio (the x value). The crystallization temperature of 10 nm HfO₂ increases from 500 °C to 900 °C for 10 nm [xHf + 1M] film, where x = 3, 3, and 1 for M = La, Al, and Ta, respectively. The incorporation of La₂O₃, and Ta₂O₅ will not compromise the dielectric constant of the film because of the high-k nature of La₂O₃, and Ta₂O₅. Angle resolved X-ray photoelectron spectroscopy (AR-XPS) reveals that when the HfO₂-to-MO[scubscript x] ALD cycle ratio is large enough (x > 3 and 4 for La and Al, respectively), periodic structures exist in films grown by this method, which are comprised of repeated M-free HfO₂ ultrathin layers sandwiched between HfM[subscript x]O[scubscript y] layers. Generally, the film thermal stability increases with thinner overall thickness, higher incorporation concentration, and stronger amorphizing capability of the incorporated elements. When the x value is low, the films are more like homogeneous films, with thermal stabilities determined by the film thickness and the amorphizer. When the x value is large enough, the periodically-repeated structure may add an extra factor to stabilize the amorphous phase. For the same incorporation concentration, films with an appropriately high periodicity may have an increased thermal stability. The manner by which the periodic structure and incorporated element affect thermal stability is explored and resolved using nanolaminates comprised of alternating layers of [scubscript y]HfO₂ and [xHf + 1M] × n, where y varied from 2 to 20, x varied from 1 to 2, and n varied from 4 to 22. / text

The development of wireless communications increases the challenges on antenna performance to improve the capability of the whole system. New fabrication technologies are emerging that not only can improve the performance of components but also provide more options for materials and geometries. One of the advanced technologies, referred to as deep X-ray lithography (XRL), can improve the performance of RF components while providing interesting opportunities for fabrication. Since this fabrication technology enables the objects of high aspect ratio (tall) structure with high accuracy, it offers RF/microwave components some unique advantages, such as higher coupling energy and compacted size. The research presented in that thesis investigates the properties of deep XRL fabricated tall microstrip transmission line and describes some important features such as characteristic impedance, attenuation, and electromagnetic field distribution. Furthermore, since most of traditional feeding structure cannot supply enough coupling energy to excite the low permittivity DRA element (εr≤10), three novel feeding schemes composed by tall microstrip line on exciting dielectric resonator antennas (DRA) with low permittivity are proposed and analyzed in this research. Both simulation and experimental measured results exhibit excellent performance. Additionally, a new simulation approach to realize Dolph-Chebyshev linear series-fed DRA arrays by using the advantages of tall microstrip line feeding structure is proposed. By using a novel T shape feeding scheme, the array exhibits wide band operation due to the low permittivity (εr=5) DRA elements and good radiation pattern due to the novel feeding structure. The tall metal transmission line feed structure and the polymer-based DRA elements could be fabricated in a common process by the deep XRL technology. This thesis firstly illustrates properties and knowledge for both DRA element and the tall transmission line. Then the three novel feeding schemes by using the tall transmission line on exciting the low permittivity DRA are proposed and one of the feeding structures, side coupling feeding, is analyzed through the simulation and experiments. Finally, the T shape feeding structure is applied into low permittivity linear DRA array design work. A novel method on designing the Dolph-Chebyshev array is proposed making the design work more efficient.

This thesis concerns studies of aqueous soft matter systems, especially surfactant micelle systems. The aim has been to study the molecular arrangement and electronic structure of the constituents of, as well as transport properties in such a system. The molecular arrangement and electronic structure has been studied by means of X-ray absorption spectroscopy (XAS) and resonant inelastic X-ray spectroscopy (RIXS). The transport properties have been investigated by low-frequency dielectric spectroscopy (LFDS) and small angle X-ray scattering (SAXS) as well as a theoretical modelling. The latter was based on Fick’s laws of the release from binary surfactant system and was validated by experiments. The RIXS and XAS measurements show the electronic structure in bulk water and the influence of the chemical surrounding of the water molecule in bulk water and of the water molecules confined in a micelle lattice. The spectra are highly dependent on the molecular arrangement in such systems. For glycine and sodium polyacrylate RIXS and XAS spectra show features which are unique for carboxyl and carboxylate groups and such measurements can thus be used for fingerprinting. The LFDS and SAXS measurements show a strong correlation between structure in a surfactant/poly-ion system and apparent mobility of surfactants. This conclusion is in line with earlier observations. By the theoretical modelling a predictive model for the surfactant release from a binary surfactant micelle system has been obtained and the importance of different factors for surfactant release has been further clarified.

Ein Dielektrischer Elastomer Aktuator (DEA) ist ein dehnbarer Kondensator, der aus einem Elastomerfilm besteht, der sich zwischen zwei flexiblen Elektroden befindet. Bei Anlegen einer elektrischen Spannung, ziehen sich die Elektroden aufgrund elektrostatischer Wechselwirkungen an, wodurch das Elastomer in z-Richtung zusammengepresst wird und sich dementsprechend in der x-,y-Ebene ausdehnt. Hierdurch werden Aktuationsbewegungen erreicht, welche sehr präzise über die Spannung gesteuert werden können. Zusätzlich sind DEAs kostengünstig, leicht und aktuieren geräuschlos. DEAs können beispielsweise für Produkte im medizinischen Bereich oder für optischer Komponenten genutzt werden. Ebenso kann aus diesen Bauteilen Strom erzeugt werden. Das größte Hindernis für eine weite Implementierung dieser Materialien liegt in den erforderlichen hohen Spannungen zum Erzeugen der Aktuationsbewegung, welche sich tendenziell im Kilovolt-Bereich befinden. Dies macht die Elektronik teuer und die Bauteile unsicher für Anwender. Um geringere Betriebsspannungen für die DEAs zu erreichen, sind signifikante Materialverbesserungen - insbesondere des verwendeten Elastomers - erforderlich. Um dies zu erreichen, können die dielektrischen Eigenschaften (Permittivität) der Elastomere gesteigert und/oder deren Steifigkeit (Young-Modul) gesenkt werden. In der vorliegenden Arbeit konnte die Aktuationsleistung von Silikonfilmen durch die Addition organischer Dipole erheblich verbessert werden. Hierfür wurde ein Verfahren etabliert, um funktionalisierte Dipole kovalent an das Polymernetzwerk zu binden. Dieser als "One-Step-Verfahren" bezeichnete Ansatz ist einfach durchzuführen und es werden homogene Filme erhalten. Die Dipoladdition wurde anhand verschiedener Silikone erprobt, die sich hinsichtlich ihrer mechanischen Eigenschaften unterschieden. Bei maximalem Dipolgehalt verdoppelte sich die Permittivität aller untersuchten Silikone und die Filme wurden deutlich weicher. Hierbei war festzustellen, dass die Netzwerkstruktur der verwendeten Silikone einen erheblichen Einfluss auf die erreichte Aktuationsdehnung hat. Abhängig vom Netzwerk erfolgte eine enorme Steigerung der Aktuationsleistung im Bereich von 100 % bis zu 4000 %. Dadurch können die Betriebsspannungen in DEAs deutlich abgesenkt werden, so dass sie tendenziell bei Spannungen unterhalb von einem Kilovolt betrieben werden können. / Dielectric elastomer actuators (DEAs) are compliant capacitors consisting of an elastomer film between two flexible electrodes. When a voltage is applied the electrostatic attraction of the electrodes leads to a contraction of the polymer in the z-direction and to a corresponding expansion in the x,y-plane. DEAs show high actuation strains, which are very accurate and adjustable by the applied voltage. In addition these devices are low-cost, low-weight and the actuation is noise-free. DEAs can be used for medical applications, optical components or for energy harvesting. The main obstacle for a broad implementation of this technology is the high driving voltage, which tends to be several thousand volts. For this reason the devices are unsafe for users and the needed electronic components are expensive. A significant improvement of the materials - especially of the used elastomer - is necessary to lower the actuation voltages. This can be achieved by improving the dielectric properties (permittivity) of the elastomer and/or by lowering it's stiffness (Young's modulus). In this work the actuation performance of silicone lms was improved significantly by the addition of organic dipoles. A simple procedure was developed, in which functionalized dipoles were bound to the polymer matrix, leading to homogenous and transparent films. This so-called "one-step-film-formation" was tested on various silicones with different mechanical properties. For the highest dipole content the permittivity of all tested silicones was doubled and the modified films showed a substantially lower stiffness. It was proven that the structure of the macromolecular network has a clear impact on the achievable actuation properties. For the highest dipole contents the actuation performance increased remarkably by 100 % up to 4000 % in respect to the investigated network. The addition of organic dipoles to the elastomer enables a signicant reduction of the needed driving voltage for DEAs below one kilovolt.

In the dissertation AVBVICVII type compounds are analyzed theoretically and experimentally. Theoretical studies were carried out using Density Functional Theory (DFT), along with the Full Potential Linearized Augmented Plane Wave (FP-LAPW) method and the Generalized Gradient Approximation (GGA). For calculations Wien2k and PHONON comp. packages were used. Experimental studies were performed using spectroscopic ellipsometry method and measuring permittivity (electrical capacitance) as a function of temperature. The study discusses AVBVICVII type compounds’ inter-atomic chemical bonding, the electronic structure, optical properties, lattice dynamics, vibrational thermodynamic functions and dielectric properties in the paraelectric, ferroelectric and antiferroelectric phases. / Disertacijoje teoriškai ir eksperimentiškai nagrinėjami AVBVICVII tipo junginiai. Teoriniai tyrimai atlikti naudojantis tankio funkcionalo teorija kartu su pilno potencialo tiesinių padidintų plokščių bangų metodu ir apibendrinto gradiento aproksimacija. Skaičiavimams naudoti Wien2k ir PHONON komp. paketai. Eksperimentiniai tyrimai buvo atliekami naudojantis spektroskopinės elipsometrijos metodais bei matuojant dielektrinės skvarbos (elektrinės talpos) priklausomybes nuo temperatūros. Darbe nagrinėjamas AVBVICVII tipo junginių tarpatominis cheminis ryšys, elektroninė struktūra, optinės savybės, gardelės dinamika, virpesių termodinaminės funkcijos ir dielektriniai pokyčiai paraelektrinėje, feroelektrinėje ir antiferoelektrinėje fazėse.

The progress of the silicon-based complementary-metal-oxide-semiconductor (CMOS) technology is mainly contributed to the scaling of the individual component. After decades of development, the scaling trend is approaching to its limitation, and there is urgent needs for the innovations of the materials and structures of the MOS devices, in order to postpone the end of the scaling. Atomic layer deposition (ALD) provides precise control of the deposited thin film at the atomic scale, and has wide application not only in the MOS technology, but also in other nanostructures. In this dissertation, I study rapid thermal processing (RTP) treatment of thermally grown SiO2, ALD growth of SiO2, and ALD growth of high-k HfO2 dielectric materials for gate oxides of MOS devices. Using a lateral heating treatment of SiO2, the gate leakage current of SiO2 based MOS capacitors was reduced by 4 order of magnitude, and the underlying mechanism was studied. Ultrathin SiO2 films were grown by ALD, and the electrical properties of the films and the SiO2/Si interface were extensively studied. High quality HfO2 films were grown using ALD on a chemical oxide. The dependence of interfacial quality on the thickness of the chemical oxide was studied. Finally I studied growth of HfO2 on two innovative interfacial layers, an interfacial layer grown by in-situ ALD ozone/water cycle exposure and an interfacial layer of etched thermal and RTP SiO2. The effectiveness of growth of high-quality HfO2 using the two interfacial layers are comparable to that of the chemical oxide. The interfacial properties are studied in details using XPS and ellipsometry.

Inadequate compaction of a soil subgrade can lead to detrimental outcomes that are not only costly but dangerous to the general public. To avoid this, quality control (QC) devices such as the nuclear density gauge (NDG) are currently being used to monitor the compaction and moisture content of soil subgrades. However, regulatory concerns associated with the NDG have encouraged federal and state agencies, as well as the heavy civil construction industry to consider non-nuclear devices for QC testing of compacted soils. One such non-nuclear device is the Soil Density Gauge (SDG), which utilizes electromagnetic wave propagation to obtain soil properties such as wet unit weight and moisture content. This research shows that through using soil-specific trend lines, the SDG has the capability of obtaining an equivalent NDG wet unit weight. Alongside the SDG, two dielectric moisture probes were also evaluated and through a calibration process on compacted soils, a general moisture content trend line was developed. This general moisture content trend line related outputted volumetric moisture contents from the moisture probes to gravimetric moisture contents. Field data were then plotted along with the general moisture content trend line to show that these devices have the potential of predicting gravimetric moisture contents. By combining the results of the SDG and moisture probe analyses, graphs were then developed that relate SDG wet unit weights to NDG dry unit weights using soil and moisture-specific trend lines.