Narrowband spectral filters find important applications in optical fiber communication systems, particularly in wavelength demultiplexers and single-frequency semiconductor lasers. Conventional Fabry-Perot resonators provide a narrow spectral width but lack the capability of mode discrimination. A new coupled-waveguide Fabry-Perot resonator made of two parallel waveguides with reflecting mirrors at the ends is proposed for application as narrowband tuned spectral filter in single-mode diode lasers and wavelength demultiplexers. The interference of counter propagating waves from reflection by end mirrors and the coupling of waves between the two parallel guides contribute to the operation of this resonator structure. Thus, the device exhibits the attributes of both Fabry-Perot resonator and directional coupler. The coupled-mode theory of parallel waveguides is employed to analyze the proposed structure. Spectral characteristics are derived from the governing coupled-mode equations and related boundary conditions. Two geometries consisting of identical waveguides, as well as nonidentical waveguides, are examined. The spectral characteristics of the proposed resonator demonstrate that significant improvement in mode discrimination capability and longitudinal mode spacing over the conventional Fabry-Perot resonator is achieved. Numerical results for several example cases are presented and the influence of various parameters on spectral properties are investigated. / Master of Science

A surface acoustic wave sensor based on an extrinsic Fabry-Perot interferometer is described. A single-mode fiber, used as the input/output fiber, and a multimode fiber, used mainly as a reflector, form an air-gap that acts as a low-finesse Fabry-Perot cavity. The Fresnel reference reflection from the glass/air interface at the front of the air-gap interferes with the sensing reflection from the air/glass interface at the far end of the air-gap in the input/output fiber. Strains in the silica tube housing the two fibers change the air-gap length, thereby altering the phase difference between the reference and sensing reflections and modulating the output intensity. A theoretical analysis of the interaction between the strain induced by the acoustic fields and the fiber sensor is presented. Because signal drifting in interferometric sensors is common, a dual optical wavelength stabilization technique is also incorporated into the sensor to minimize the effect. Signal to noise ratios (SNR’s) on the order of 39 dB are obtained with a strain sensitivity of 4°/ μstrain cm⁻¹. / Master of Science

DNA detection technology has developed rapidly due to its extensive application in clinical diagnostics, bioengineering, environmental monitoring, and food science areas. Currently developed methods such as surface Plasmon resonance (SPR) methods, fluorescent dye labeled methods and electrochemical methods, usually have the problems of bulky size, high equipment cost and time-consuming algorithms, so limiting their application for in vivo detection. In this work, an intrinsic Fabry-Perot interferometric (IFPI) based DNA sensor is presented with the intrinsic advantages of small size, low cost and corrosion-tolerance. This sensor has experimentally demonstrated its high sensitivity and selectivity. In theory, DNA detection is realized by interrogating the sensor's optical cavity length variation resulting from hybridization event. First, a microgap structure based IFPI sensor is fabricated with simple etching and splicing technology. Subsequently, considering the sugar phosphate backbone of DNA, layer-by-layer electrostatic self-assembly technique is adopted to attach the single strand capture DNA to the sensor endface. When the target DNA strand binds to the single-stranded DNA successfully, the optical cavity length of sensor will be increased. Finally, by demodulating the sensor spectrum, DNA hybridization event can be judged qualitatively. This sensor can realize DNA detection without attached label, which save the experiment expense and time. Also the hybridization detection is finished within a few minutes. This quick response feature makes it more attractive in diagnose application. Since the sensitivity and specificity are the most widely used statistics to describe a diagnostic test, so these characteristics are used to evaluate this biosensor. Experimental results demonstrate that this sensor has a sensitivity of 6nmol/ml and can identify a 2 bp mismatch. Since this sensor is optical fiber based, it has robust structure and small size ( 125μm ). If extra etching process is applied to the sensor, the size can be further reduced. This promises the sensor potential application of in-cell detection. Further investigation can be focused on the nanofabrication of this DNA sensor, and this is very meaningful topic not only for diagnostic test but also in many other applications such as food industry, environment monitoring. / Master of Science

Sapphire fiber based temperature sensors are exceptional in their ability to operate at temperatures above 1000C and as high as 1800C. Sapphire fiber technology is emerging and the fiber is available commercially. Sapphire fiber has a high loss, is highly multi-mode and does not have a solid cladding, but it is nonetheless very useful in high temperature applications. Of the available interferometer configurations, Fabry-Perot interferometers are distinguished in their high accuracy and great isolation from sources of error. In this thesis, improvements are reported to an existing design to enhance its reliability and to reduce possible modes of failure. The existing high temperature sensor design has shown a lot of potential in the past by continuously measuring the temperature in a coal gasifier for 7 months, but its true potential has not yet been realized. The goal of this work and the work of many others is to extend the working life and reliability of high-temperature optical sapphire temperature sensors in harsh environments by exploring a solid cladding for sapphire fiber, improved fringe visibility sapphire wafers and a new sensor design. This project is supported by the National Energy and Technology Laboratory of the Department of Energy. / Master of Science

Miniature pressure sensors which can endure harsh environments are a highly sought after goal in industrial, medical and research fields. Microelectromechanical systems (MEMS) are the current methods to fabricate such small sensors. However, they suffer from low sensitivity and poor mechanical properties. To fulfill the need for robust and reliable miniature pressure sensors that can operate under high temperatures, a novel type of optical fiber tip sensor only 125μm in diameter is presented in this thesis. The essential element is a piece of hollow fiber which connects the fiber end and a diaphragm to form a Fabry-Pérot cavity. The all-fused-silica structure fabricated directly on a fiber tip has little temperature dependence and can function very well with high resolution and accuracy at temperatures up to 600 °C. In addition to its miniature size, its advantages include superior mechanical properties, biocompatibility, immunity to electromagnetic interference, disposability and cost-effective fabrication. The principle of operation, design analysis, fabrication implementation and performance evaluation of the sensor are discussed in detail in the following chapters. / Master of Science

O objetivo do presente trabalho foi o estudo e análise da resposta óptica de dispositivos de cristal fotônico uni-dimensional (1D) fabricados através do uso da tecnologia de silício poroso. Os resultados obtidos neste trabalho apresentam contribuições significativas no desenvolvimento de uma tecnologia para a fabricação de dispositivos ópticos em silício. As principais contribuições deste trabalho estão direcionadas ao aprimoramento dos processos de fabricação de cristais fotônicos 1D e processos de tratamento térmico. Os resultados da análise estrutural através de microscopia óptica de varredura (MEV) e da resposta óptica (refletância ou absorbância) mostraram que dispositivos de cristal fotônico fabricados em soluções altamente diluídas de HF apresentam melhor desempenho, tendo sido otimizado o processo de fabricação utilizando-se uma célula de duplo compartimento (célula dupla). A otimização da resposta óptica dos dispositivos foi atribuída ao efeito de minimização das rugosidades de interface e minimização de efeitos de anisotropia na taxa de corrosão durante o processo de anodização eletroquímica. O processo eletroquímico utilizado para a fabricação de cristais fotônicos 1D apresentou limitação quanto ao número máximo de camadas, sendo observado que dispositivos com número de camadas acima de 60 apresentavam degradação das suas camadas superficiais, comprometendo a resposta óptica do dispositivo. Este resultado foi atribuído a efeitos de diluição química das camadas expostas à solução por longos períodos de processo. Os dispositivos fotônicos 1D mostraram-se sensíveis a processos de recozimento térmico, deslocando suas bandas fotônicas proibidas para regiões de menor comprimento de onda devido à mudança do índice de refração das camadas e aos efeitos de expansão e compressão das camadas constitutivas do dispositivo. Os dispositivos de micocavidade Fabry-Perot mostraram-se mais sensíveis aos processos de recozimento térmico. Os resultados obtidos no presente trabalho vislumbram grandes possibilidades de aplicação dos cristais fotônicos de PS na fabricação de dispositivos ópticos na tecnologia de silício como filtros, lentes, cavidades ressonantes, guias de ondas, grades de difração e dispositivos sensores. / The aim of the present work was to study and analyze the optical response of one- dimensional (1D) photonic crystal devices obtained by using the porous silicon technology. The experimental results obtained from this work showed the significant contribution to the development of a technological process for optical device fabrication in the silicon substrate. The most important contributions of the work are pointed out to improve the electrochemical process for device fabrication and thermal annealing process in order to improve the optical response of the devices. The results obtained from Scanning electronic microscopy (SEM) and from the optical response of the devices, showed that devices fabricated in the double cell and diluted HF solution improved their optical response due to minimization of the anisotropy of corrosion rate and decreasing of the surface roughness between layers. The electrochemical process used for device fabrication showed the existence of limitation on the numbers of layers because of the existence of chemical dissolution effect that became important for long time process. The 1D photonic crystal devices in PS technology showed high sensibility to thermal annealing process, due to the refraction index change after thermal annealing the photonic band gap position shift down to low wavelength region. The Fabry-Perot devices showed higher sensibility to thermal annealing process improving their optical response after annealing process. The results obtained from the present work showed that the PS 1D photonic device could be applied to optical devices fabrication in silicon technology such as optical filters, lenses, resonant cavities, wave-guide devices, diffraction grade and optical sensor device.

Este trabalho apresenta o projeto de pesquisa desenvolvido para a obtenção do título de Mestre em Engenharia Elétrica, na área de concentração de engenharia de sistemas, da Escola Politécnica da Universidade de São Paulo. O principal objetivo deste trabalho foi o desenvolvimento de um sistema de acionamento (driver) para os atuadores piezoelétricos do interferômetro de Fabry-Pérot do espectrômetro BTFI (Brazilian Tunable Filter Imager), um instrumento visitante do telescópio SOAR (Southern Astrophysical Research Telescope), no Chile. O Fabry-Pérot é um instrumento óptico composto de duas superfícies paralelas altamente reflexivas (espelhos), cuja distância é controlada por um sistema de nanoposicionamento composto de três atuadores piezoelétricos (piezos) do tipo APA® (Amplified Piezoelectric Actuators) e um sistema de medida capacitivo. O principal requisito técnico de desempenho do sistema de nanoposicionamento do Fabry-Pérot é tal que o ruído de posicionamento dos espelhos deve ser limitado a 3 . No entanto, os fenômenos não lineares de histerese e escorregamento (creep) dos piezos limitam a precisão de posicionamento do sistema de controle, razão pela qual foi desenvolvido um sistema de acionamento por carga e tensão para os piezos, com o intuito de atenuar suas não linearidades e, consequentemente, melhorar o desempenho do sistema de controle em malha fechada, em termos de ruído de posicionamento. A primeira etapa deste trabalho consistiu da caracterização do modelo e da instrumentação do sistema de nanoposicionamento do Fabry-Pérot, composto de sensores capacitivos, conversores de sinal, atuadores piezoelétricos e sistema de aquisição de dados. Após a caracterização dos componentes do sistema, sua especificação técnica de desempenho de 3 foi traduzida em requisitos de engenharia para o projeto do sistema eletrônico de acionamento dos piezos por carga e tensão, notadamente em termos de ruído, tempo de resposta, banda de resposta em frequência, ganho, corrente e tensão elétricas e dissipação de potência. Uma vez concluído o projeto do driver, um protótipo foi implementado e testado com o sistema real, a fim de se verificar experimentalmente a atenuação dos efeitos não lineares. Finalmente, foram realizados alguns experimentos com o driver e o sistema de nanoposicionamento em malha fechada, controlado por um compensador PI, a fim de se verificar a influência da atenuação das não linearidades dos piezos nesta configuração. Após a análise dos resultados experimentais obtidos, verificou-se que o ruído de posicionamento do sistema, em malha fechada, é significativamente menor quando os fenômenos não linearidades dos piezos são atenuados. / This work represents the research project to obtain the degree of Master of Sciences in Electrical Engineering, specializing in Systems Engineering, at the Escola Politécnica da Universidade de São Paulo, in São Paulo, Brazil. The main objective of this project was to design an electronic power driver for the piezoelectric actuators of the Fabry-Pérot interferometer of the BTFI spectrometer, a visitor instrument of the SOAR telescope, in Chile. Fabry-Pérot is an optical instrument composed by two high reflexive parallel surfaces (mirrors), which distance is controlled by a nanopositioning system composed by three piezoelectric actuators (piezos) of the class APA® (Amplified Piezoelectric Actuators) and a capacitive measurement system. The main performance specification of the Fabry-Pérots nanopositioning system is such that the positioning noise must be limited to 3 . However, the nonlinear behaviors (hysteresis and creep) of the piezos limit the positioning precision of the control system, for which reason a charge and voltage actuation system was developed for the piezos, in order to mitigate its nonlinearities and, consequently, improve the performance of the control system in closed loop, in terms of positioning noise. The first step in this work consisted on the characterization of the Fabry-Pérot nanopositioning systems model and instrumentation, which are composed by capacitive sensors, signal converters, piezoelectric actuators and a data acquisition board. After the characterization of the components of the nanopositioning system, the 3 specification was interpreted to low level engineering requirements for the design of the charge and voltage driver, especially in terms of noise, response time, frequency bandwidth, gain, electrical current, voltage and power dissipation. Once concluded the design of the driver, a prototype was implemented and tested in the real system, in order to verify the attenuation of the nonlinear effects. Finally, some experiments with the driver and the nanopositioning system were performed in closed loop, controlled by a PI compensator, in order to verify the influence of the attenuation of the nonlinearities of the piezos in such configuration. The analysis of the obtained experiment results showed that the nanopositioning systems noise, in closed loop, is significantly reduced when the nonlinear effects of the pizeos are attenuated.

Cette thèse a pour but l’étude théorique de métamatériaux métalliques empilés. Ces structures sont actuellement proposées pour améliorer et élargir les fonctionnalités des métamatériaux métalliques. Nous portons un intérêt particulier aux propriétés de polarisation de ces structures métalliques empilées.En premier lieu, nous précisons le type de métamatériaux que nous étudions et nous présentons la méthode modale qui nous permet de décrire les propriétés électromagnétiques de la structure. A l’aide d’un Formalisme de Jones Etendu (FJE), développé récemment dans notre équipe, nous faisons ressortir les principales propriétés de polarisation linéaire de ces métamatériaux métallique.En alliant le FJE à l’algorithme de propagation de la matrice S, nous étudions un empilement de deux métamatériaux vus comme un montage polariseur-analyseur. Nous établissons ensuite une expression de la transmission de la structure: la loi de Malus étendue. Cela nous permet notamment de démontrer les résonances de type Fabry-Perot qui ont lieu entre les métamatériaux.Pour des structures plus conséquentes, nous montrons qu’il est possible de réaliser une rotation de la polarisation, à très faible perte et spectralement agile, grâce aux résonances de type Fabry-Perot.Fondamentalement, nous révélons une nouvelle façon d’exciter des résonances Fano qui sont induites par les propriétés de polarisation des métamatériaux. Ces résonances peuvent être utilisées pour des applications de capteur ou de filtrage. De plus, ces résonances Fano induites par la polarisation ouvrent de nouvelles possibilités d’applications pour les empilement de métamatériaux métalliques. / This PhD thesis deals with the theoretical study of stacked metallic metamaterials. Such structures are currently investigated to extend the functionalities offered by single metallic metamaterials. We especially focus on the specific polarization properties of the stacked metallic metamaterials.We first present the type of metamaterial that we consider, and we describe the modal method that is used to model its electromagnetic properties. We outline the linear polarization properties characterizing the metamaterial thanks to an Extended Jones Formalism (EJF) recently developed by our team.In combination with the EJF, we apply the S-matrix algorithm to the study of a stack of two metallic metamaterials in a polarizer-analyzer configuration. We derive an analytical expression for the transmission response of the stacked structure: the Extended Malus Law. Mainly, it highlights the Fabry-Perot-like resonances located between the metamaterials.Using larger stacked structures, we demonstrate that spectrally tunable and low loss polarization rotation can be achieved owing to these Fabry-Perot-like resonances.In essence, we reveal a new way of realizing Fano resonances which are induced by the specific polarization properties of the metamaterials. We show that such resonances can be engineered for sensing or filtering applications. Moreover, the polarization-induced Fano resonances expand the possibilities of stacked metallic metamaterials.

O acesso ao tratamento da Doença de Fabry (DF) no sistema público de saúde nacional. Trata-se de uma pesquisa exploratória de corte transversal, centrada em elementos qualitativos, realizada com os profissionais e os pacientes portadores da DF, no Ambulatório de Genética Clínica do Hospital Universitário Gaffrée e Guinle - HUGG. Utilizou-se como coleta de dados a entrevista aberta e semiestruturada. Seu objetivo maior é identificar os aspectos bioéticos envolvidos no acesso ao tratamento da DF no SUS, e para tal buscamos tornar manifestos os argumentos morais dos profissionais do ambulatório, acerca da existência de uma política pública para o tratamento das doenças raras no SUS. A Bioética Principialista de Beauchamp e Childress, em seus princípios prima-facie: o respeito pela autonomia; a não maleficência; a beneficência e a justiça, é tomada como fundamentação teórica deste estudo. O tratamento dos dados se deu por meio do método de análise de conteúdo, de Bardin. A pesquisa contempla o percurso histórico das principais política públicas de saúde, e seus movimentos em direção à criação do SUS, e a integração dos hospitais universitários ao sistema público de saúde, em seus marcos legais. Ela também enfoca a mobilização da sociedade política e organizada em busca da materialização política pública de atenção às Doenças Raras. O estudo constatou que os princípios de Justiça e da Beneficência emergiram espontaneamente, e por vezes implicitamente, na fala do sujeitos da pesquisa, em suas justificativas morais para a criação de uma política pública para Doenças Raras. Ademais, é delineado o curso da doença na família, haja vista tratar-se de doença hereditária. Assinala-se de que modo a DF chegou do acaso a estas pessoas, e como estas chegaram ao diagnóstico e tratamento. / The access to the treatment of Fabry Disease (FD) in the national health public system. Explanatory cross sectional research, centered on qualitative elements, performed with the professionals and patients that carry the FD, at the Clinic Genetics Ambulatory of the Gaffrée and Guinle University Hospital HUGG. An open and semi-structured interview was used as data collection. Its greatest objective is to identify the bioethics aspects involved in the access to the treatment of FB at Unified Health System, in order to do so, we intend to become the moral arguments of the ambulatory professionals manifest, regarding the existence of a public policy to the treatment of rare diseases at SUS. The Beauchamp and Childress Principialist Bioethics, in its prima-facia principles: the respect for the autonomy; the non-maleficence; the beneficence and justice, is taken as theoretical fundament for this study. The data was treated by means of Bardins Content Analysis Method. The research contemplates the historical background of the main health public policy and its movements towards SUS formation, and the integration of the university hospitals in the health public system, in its legal frameworks. It also emphasizes the mobilization of the political and organized society seeking the materialization of the public policy concerning the Attention to Rare Diseases. The study found that the Justice and Beneficence principles emerged spontaneously, and occasionally implicitly, in the investigation subjects speech, in their moral justifications to the creation of a public policy to Rare Diseases. Moreover, it is outlined the course of the disease within the family, due to it being a hereditary disease. It is noted how the FD reached by chance these people, and how they accessed the diagnosis and treatment.

O acesso ao tratamento da Doença de Fabry (DF) no sistema público de saúde nacional. Trata-se de uma pesquisa exploratória de corte transversal, centrada em elementos qualitativos, realizada com os profissionais e os pacientes portadores da DF, no Ambulatório de Genética Clínica do Hospital Universitário Gaffrée e Guinle - HUGG. Utilizou-se como coleta de dados a entrevista aberta e semiestruturada. Seu objetivo maior é identificar os aspectos bioéticos envolvidos no acesso ao tratamento da DF no SUS, e para tal buscamos tornar manifestos os argumentos morais dos profissionais do ambulatório, acerca da existência de uma política pública para o tratamento das doenças raras no SUS. A Bioética Principialista de Beauchamp e Childress, em seus princípios prima-facie: o respeito pela autonomia; a não maleficência; a beneficência e a justiça, é tomada como fundamentação teórica deste estudo. O tratamento dos dados se deu por meio do método de análise de conteúdo, de Bardin. A pesquisa contempla o percurso histórico das principais política públicas de saúde, e seus movimentos em direção à criação do SUS, e a integração dos hospitais universitários ao sistema público de saúde, em seus marcos legais. Ela também enfoca a mobilização da sociedade política e organizada em busca da materialização política pública de atenção às Doenças Raras. O estudo constatou que os princípios de Justiça e da Beneficência emergiram espontaneamente, e por vezes implicitamente, na fala do sujeitos da pesquisa, em suas justificativas morais para a criação de uma política pública para Doenças Raras. Ademais, é delineado o curso da doença na família, haja vista tratar-se de doença hereditária. Assinala-se de que modo a DF chegou do acaso a estas pessoas, e como estas chegaram ao diagnóstico e tratamento. / The access to the treatment of Fabry Disease (FD) in the national health public system. Explanatory cross sectional research, centered on qualitative elements, performed with the professionals and patients that carry the FD, at the Clinic Genetics Ambulatory of the Gaffrée and Guinle University Hospital HUGG. An open and semi-structured interview was used as data collection. Its greatest objective is to identify the bioethics aspects involved in the access to the treatment of FB at Unified Health System, in order to do so, we intend to become the moral arguments of the ambulatory professionals manifest, regarding the existence of a public policy to the treatment of rare diseases at SUS. The Beauchamp and Childress Principialist Bioethics, in its prima-facia principles: the respect for the autonomy; the non-maleficence; the beneficence and justice, is taken as theoretical fundament for this study. The data was treated by means of Bardins Content Analysis Method. The research contemplates the historical background of the main health public policy and its movements towards SUS formation, and the integration of the university hospitals in the health public system, in its legal frameworks. It also emphasizes the mobilization of the political and organized society seeking the materialization of the public policy concerning the Attention to Rare Diseases. The study found that the Justice and Beneficence principles emerged spontaneously, and occasionally implicitly, in the investigation subjects speech, in their moral justifications to the creation of a public policy to Rare Diseases. Moreover, it is outlined the course of the disease within the family, due to it being a hereditary disease. It is noted how the FD reached by chance these people, and how they accessed the diagnosis and treatment.