Technology scaling beyond Moore’s law demands cutting-edge solutions of the gate length scaling in sub-10 nm regime for low power high speed operations. Recently SOI technology has received considerable attention, however manufacturable solutions in sub-10 nm technologies are not yet known for future nanoelectronics. Therefore, to continue scalinginsub-10 nm region, new one(1D) and two dimensional(2D) “nano-materials” and engineering are expected to keep its pace. However, significant challenges must be overcome for nano-material properties in carrier transport to be useful in future silicon nanotechnology. Thus, it is very important to understand and modulate their electronic band structure and transport properties for low power nanoelectronics applications. This thesis tries to provide solutions for some problems in this area. In recent times, one dimensional Silicon nanowire has emerged as a building block for the next generation nano-electronic devices as it can accommodate multiple gate transistor architecture with excellent electrostatic integrity. However as the experimental study of various energy band parameters at the nanoscale regime is extremely challenging, usually one relies on the atomic level simulations, the results of which are at par with the experimental observations. Two such parameters are the band gap and effective mass, which are of pioneer importance for the understanding of the current transport mechanism. Although there exists a large number of empirical relations of the band gap in relaxed Silicon nanowire, however there is a growing demand for the development of a physics based analytical model to standardize different energy band parameters which particularly demands its application in TCAD software for predicting different electrical characteristics of novel devices and its strained counterpart to increase the device characteristics significantly without changing the device architecture. In the first part of this work reports the analytical modeling of energy band gap and electron transport effective mass of relaxed and strained Silicon nanowires in various crystallographic directions for future nanoelectronics. The technology scaling of gate length in beyond Moore’s law devices also demands the SOI body thickness, TSi0 which is essentially very challenging task in nano-device engineering. To overcome this circumstance, two dimensional crystals in atomically thin layered materials have found great attention for future nanolectronics device applications. Graphene, one layer of Graphite, is such 2D materials which have found potentiality in high speed nanoelectronics applications due to its several unique electronic properties. However, the zero band gap in pure Graphene makes it limited in switching device or transistor applications. Thus, opening and tailoring a band gap has become a highly pursued topic in recent graphene research. The second part of this work reports atomistic simulation based real and complex band structure properties Graphene-Boron nitride heterobilayer and Boron Nitride embedded Graphene nanoribbons which can improve the grapheme and its nanoribbon band structure properties without changing their originality. This part also reports the direct band-to-band tunneling phenomena through the complex band structures and their applications in tunnel field effect transistors(TFETs) which has emerged as a strong candidate for next generation low-stand by power(LSTP) applications due to its sub-60mV/dec Sub threshold slope(SS). As the direct band-to-band tunneling(BTBT) is improbable in Silicon(either its bulk or nanowire form), it is difficult to achieve superior TFET characteristics(i.e., very low SS and high ON cur-rent) from the Silicon TFETs. Whereas, it is explored that much high ON current and very low subthreshold slope in hybrid Graphene based TFET characteristics open a new prospect in future TFETs. The investigations on ultrathin body materials also call for a need to explore new 2D materials with finite band gap and their various nanostructures for future nanoelectronic applications in order to replace conventional Silicon. In the third part of this report, we have investigated the electronic and dielectric properties of semiconducting layered Transition metal dichalcogenide materials (MX2)(M=Mo, W;X =S, Se, Te) which has recently emerged as a promising alternative to Si as channel materials for CMOS devices. Five layered MX2 materials(exceptWTe2)in their 2D sheet and 1D nanoribbon forms are considered to study the real and imaginary band structure of thoseMX2 materials by atomistic simulations. Studying the complex dispersion properties, it is shown that all the five MX2 support direct BTBT in their monolayer sheet forms and offer an average ON current and subthresholdslopeof150 A/mand4 mV/dec, respectively. However, onlytheMoTe2 support direct BTBT in its nanoribbon form, whereas the direct BTBT possibility in MoS2 and MoSe2 depends on the number of layers or applied uniaxial strain. WX2 nanoribbons are shown to be non-suitable for efficient TFET operation. Reasonably high tunneling current in these MX2 shows that these can take advantage over conventional Silicon in future tunnel field effect transistor applications.

Technology scaling beyond Moore’s law demands cutting-edge solutions of the gate length scaling in sub-10 nm regime for low power high speed operations. Recently SOI technology has received considerable attention, however manufacturable solutions in sub-10 nm technologies are not yet known for future nanoelectronics. Therefore, to continue scalinginsub-10 nm region, new one(1D) and two dimensional(2D) “nano-materials” and engineering are expected to keep its pace. However, significant challenges must be overcome for nano-material properties in carrier transport to be useful in future silicon nanotechnology. Thus, it is very important to understand and modulate their electronic band structure and transport properties for low power nanoelectronics applications. This thesis tries to provide solutions for some problems in this area. In recent times, one dimensional Silicon nanowire has emerged as a building block for the next generation nano-electronic devices as it can accommodate multiple gate transistor architecture with excellent electrostatic integrity. However as the experimental study of various energy band parameters at the nanoscale regime is extremely challenging, usually one relies on the atomic level simulations, the results of which are at par with the experimental observations. Two such parameters are the band gap and effective mass, which are of pioneer importance for the understanding of the current transport mechanism. Although there exists a large number of empirical relations of the band gap in relaxed Silicon nanowire, however there is a growing demand for the development of a physics based analytical model to standardize different energy band parameters which particularly demands its application in TCAD software for predicting different electrical characteristics of novel devices and its strained counterpart to increase the device characteristics significantly without changing the device architecture. In the first part of this work reports the analytical modeling of energy band gap and electron transport effective mass of relaxed and strained Silicon nanowires in various crystallographic directions for future nanoelectronics. The technology scaling of gate length in beyond Moore’s law devices also demands the SOI body thickness, TSi0 which is essentially very challenging task in nano-device engineering. To overcome this circumstance, two dimensional crystals in atomically thin layered materials have found great attention for future nanolectronics device applications. Graphene, one layer of Graphite, is such 2D materials which have found potentiality in high speed nanoelectronics applications due to its several unique electronic properties. However, the zero band gap in pure Graphene makes it limited in switching device or transistor applications. Thus, opening and tailoring a band gap has become a highly pursued topic in recent graphene research. The second part of this work reports atomistic simulation based real and complex band structure properties Graphene-Boron nitride heterobilayer and Boron Nitride embedded Graphene nanoribbons which can improve the grapheme and its nanoribbon band structure properties without changing their originality. This part also reports the direct band-to-band tunneling phenomena through the complex band structures and their applications in tunnel field effect transistors(TFETs) which has emerged as a strong candidate for next generation low-stand by power(LSTP) applications due to its sub-60mV/dec Sub threshold slope(SS). As the direct band-to-band tunneling(BTBT) is improbable in Silicon(either its bulk or nanowire form), it is difficult to achieve superior TFET characteristics(i.e., very low SS and high ON cur-rent) from the Silicon TFETs. Whereas, it is explored that much high ON current and very low subthreshold slope in hybrid Graphene based TFET characteristics open a new prospect in future TFETs. The investigations on ultrathin body materials also call for a need to explore new 2D materials with finite band gap and their various nanostructures for future nanoelectronic applications in order to replace conventional Silicon. In the third part of this report, we have investigated the electronic and dielectric properties of semiconducting layered Transition metal dichalcogenide materials (MX2)(M=Mo, W;X =S, Se, Te) which has recently emerged as a promising alternative to Si as channel materials for CMOS devices. Five layered MX2 materials(exceptWTe2)in their 2D sheet and 1D nanoribbon forms are considered to study the real and imaginary band structure of thoseMX2 materials by atomistic simulations. Studying the complex dispersion properties, it is shown that all the five MX2 support direct BTBT in their monolayer sheet forms and offer an average ON current and subthresholdslopeof150 A/mand4 mV/dec, respectively. However, onlytheMoTe2 support direct BTBT in its nanoribbon form, whereas the direct BTBT possibility in MoS2 and MoSe2 depends on the number of layers or applied uniaxial strain. WX2 nanoribbons are shown to be non-suitable for efficient TFET operation. Reasonably high tunneling current in these MX2 shows that these can take advantage over conventional Silicon in future tunnel field effect transistor applications.

Compact Models are the physically based accurate mathematical description of the cir-cuit elements, which are computationally efficient enough to be incorporated in circuit simulators so that the outcome becomes useful for the circuit designers. As the multi-gate MOSFETs have appeared as replacements for bulk-MOSFETs in sub-32nm technology nodes, efficient compact models for these new transistors are required for their successful utilization in integrated circuits. Existing compact models for common double-gate (CDG) MOSFETs are based on the fundamental assumption of having symmetric gate oxide thickness. In this work we explore the possibility of developing models without this approximation, while preserving the computational efficiency at the same level. Such effort aims to generalize the compact model and also to capture the oxide thickness asymmetry effect, which might prevail in practical devices due to process uncertainties and thus affects the device performance significantly. However solution to this modeling problem is nontrivial due to the bias-dependent asym-metric nature of the electrostatic. Using the single implicit equation based Poisson so-lution and the unique quasi-linear relationship between the surface potentials, previous researchers of our laboratory have reported the core model for such asymmetric CDG MOSFET. In this work effort has been put to include Non-Quasistatic (NQS) effects, different small-geometry effects, and noise model to this core, so that the model becomes suitable for practical applications. It is demonstrated that the quasi-linear relationship between the surface potentials remains preserved under NQS condition, in the presence of all small geometry effects. This property of the device along with some other new techniques are used to develop the model while keeping the mathematical complexity at the same level of the models reported for the symmetric devices. Proposed model is verified against TCAD simulation for various device geometries and successfully imple-mented in professional circuit simulator. The model passes the source/drain symmetry test and good convergence is observed during standard circuit simulations.

Ce travail nous a permis de réaliser une étude de capteurs de gaz et d’humidité à base de graphène. Cette étude pourrait être utile non seulement pour améliorer les performances des capteurs à base de graphène mais aussi pour mieux comprendre l’interaction entre le graphène et les molécules de gaz. Ceci semble indispensable pour faire avancer les applications du graphène comme un matériau prometteur pour la détection des gaz. Des avancées significatives ont été présentées au niveau de la fabrication de ces capteurs, leurs différentes caractérisations électriques ainsi que d’autres techniques employées pour analyser le mécanisme contrôlant la détection des molécules de gaz/vapeur. Ces outils ont été mis en place pour concevoir et fabriquer plusieurs structures de capteur en utilisant différents substrats support du graphène d’une part et en modifiant les propriétés du graphène par utilisation des produits chimiques d’autres part. La caractérisation de ces capteurs sous différents environnements a permis de comparer les différentes réponses des capteurs et d’en tirer plusieurs conclusions sur le fonctionnement de ces dispositifs. En effet, le Mica, un substrat lisse et transparent, a été utilisé comme substrat pour le graphène. Le dopage induit par le mica a été étudié ainsi que son impact sur la sensibilité du graphène au gaz d’ammoniac. Ceci a permis de mettre en évidence le fait que le substrat joue un rôle important pour la détection de l’ammoniac. De plus, ces capteurs fabriques sur mica et SiO2 ont été testés sous différentes conditions de températures et d’oxygène. Dans une autre approche, un polymère a été utilisé pour doper le graphène. Une étude détaillée a été menée pour analyser le comportement de ce graphène fonctionnalisé par rapport aux molécules d’eau. Ces nouveaux résultats expérimentaux obtenus pendant cette thèse constituent un bon support à plusieurs résultats théoriques établis et permettent d’optimiser la conception des capteurs de gaz à base de graphène pour des meilleures performances. / In this research, we report on a study of graphene based gas and humidity sensors. This study could be useful not only to improve the performance of graphene based sensors but also to better understand the interaction between graphene and gas molecules. This seems necessary to promote the applications of graphene as a promising material for gas sensing. Significant advances have been made to design and fabricate these sensors: the different electrical characterizations as well as other techniques used to analyze the mechanism controlling the detection of gas/vapor molecules. These tools have been set up to design and manufacture various sensor structures using different underlying substrates for graphene on one hand and chemical modification of graphene properties on the other hand. The characterization of these sensors under different environments was used to compare the different responses of the sensors and draw several conclusions about gas sensing mechanism. Indeed, Mica, a smooth and transparent substrate, was used as a supporting substrate for graphene. Doping induced to graphene by mica and its impact on graphene sensitivity to ammonia gas were studied. This has made it possible to highlight the fact that the substrate plays an important role for the detection of ammonia. In addition, these sensors made on mica and SiO2 were tested under a variety of temperatures and oxygen. In another approach, a polymer was used to dope graphene. A detailed study was realized about the behavior of water molecules on functionalized graphene. The obtained experimental results, reported for the first time, represent a good support for several theoretical studies already made and could be used to optimize the design of graphene based gas sensors.

L'objectif de cette thèse était de démontrer les potentialités de l'impression à jet d'encre pour le pilotage d'une HLED contenant des clusters métalliques phosphorescents dans le rouges, par des transistors organiques à effet de champs. Pour atteindre ce but, le projet a été divisé en deux parties : I) La fabrication et l'optimisation de transistors organiques de type n par photolithographie puis le transfert technologique vers l'impression à jet d'encre. II) Parallèlement au développement des transistors, je me suis attaché à la conception de matériaux hybrides luminescents pour la réalisation d'HLED. Pour la partie transistor, nous avons obtenu une meilleure compréhension des facteurs influençant l'injection de charges mais aussi la stabilité électrique pour un transistor de géométrie grille basse/contacts bas avec le fullerène C60 évaporé. Nous avons démontré que la résistance de contact est d'une part gouvernée par la morphologie du SCO au niveau des électrodes et d'autre part indépendante du travail de sortie du métal. En outre, nous avons vu que la stabilité électrique des transistors est fortement impactée par la nature du contact source et drain. L'optimisation des transistors fabriqués par photolithographie, qui a essentiellement consisté à modifier les interfaces, nous a permis de développer des transistors de type n performants avec des mobilités à effet de champ saturées allant jusqu'à 1,5 cm2/V.s pour une température maximum de procédé de 115 °C. Le transfert vers un transistor fabriqué par impression à jet d'encre a ensuite été effectué. Nous avons ensuite démontré que les morphologies de l'électrode de grille et de l'isolant, fabriqués par impression à jet d'encre, ont un impact négligeable sur les performances des transistors. Pour notre structure imprimée, l'injection de charges aux électrodes S/D est en fait le facteur clé pour la réalisation de transistors performants. Finalement, des matériaux phosphorescents rouges à base de cluster métalliques octaédrique de molybdène ont été développés. Le copolymère hybride résultant présentait un rendement quantique de photoluminescence de 51 %. La réalisation de l'HLED a ensuite été effectuée par combinaison d'une LED bleue commercial et du copolymère dopé avec des clusters octaédriques de molybdène pour des applications possibles en biologie ou dans l'éclairage. / The objective of this thesis was to demonstrate the potentialities of inkjet printing for driving an HLED containing red phosphorescent metallic clusters, with organic field effect transistors. To achieve this goal, the project was divided into two parts: I) The fabrication and optimization of n-type organic transistors by photolithography and then transfer to inkjet printing. II) Parallel to the development of transistors, I focused on designing luminescent hybrid materials for HLED realization. Concerning transistors, we obtained a better understanding of the factors influencing the charge injection but also the electrical stability for bottom gate/ bottom contact geometry transistor with evaporated C60 semiconductor. We have demonstrated that the contact resistance is on the one hand governed by the morphology of the SCO at the electrodes and on the other hand independent of the metal work function. In addition, we have observed that transistors electrical stability of is strongly impacted by the source and drain contact nature. The optimization of photolithography transistors, which essentially consisted of modifying the interfaces, allowed us to develop efficient n-type transistors with saturated field effect mobilities of up to 1.5 cm2/V.s for a maximal process temperature of 115 °C. The technological transfer to inkjet printed transistors was then performed. We then demonstrated that gate electrode and insulator morphologies deposited by inkjet printing, have a negligible impact on transistors performances. For our printed structure, charges injection at the S/D electrodes is in fact the key factor for high performance transistors realization. Finally, red phosphorescent materials based on molybdenum octahedral metal cluster have been developed. The resulting hybrid copolymer showed photoluminescence quantum yield up to 51%. The realization of the HLED was then carried out by combining a commercial blue LED and the copolymer doped with octahedral molybdenum clusters for possible applications in biology or lighting.

Les Oligothiophènes sont étudiés depuis une quinzaine d’années dans le cadre du développement d’applications électroniques et plus particulièrement des transistors à effet de champ organiques (OFETs). Dans ce contexte, une série de dialkylterthiophènes a été synthétisée et l’organisation supramoléculaire a été caractérisée en volume à l’aide de différentes techniques. L’analyse enthalpique différentielle nous a, tout d’abord permis de détecter les transitions de phases de chaque composé et de caractériser précisément les températures et les enthalpies de transitions. Nous avons constaté que chaque système présente une ou plusieurs phases cristal-liquides. Leur nature smectique ainsi que leur structure ont été identifiées par microscopie optique polarisée et par diffraction des rayons X. Pour les phases smectiques les plus ordonnées, la diffraction RX a révélé une organisation supramoléculaire à l’intérieur des plans smectiques, symptomatique de phases smectiques-cristallines. Les paramètres de maille de chaque système en phase cristalline ou SmG, ont été déterminés à l’aide d’une méthode de simulation. Les propriétés thermotropes et structurales sont discutées en fonction de la longueur des chaines alkyles.<p>Un composé cristal-liquide de la série précédente, le dioctylterthiophène, a ensuite été caractérisé en couche mince afin d’étudier les effets d’interfaces sur sa structure. La caractérisation, par diffraction des rayons X et microscopie à force atomique, de films minces de différentes épaisseurs, a révélé l’existence d’une phase ‘‘couche mince’’ à partir de leur interface substrat/composé et sur une épaisseur d’environ 30 nm. Au-delà de cette épaisseur, la phase en volume domine l’organisation supramoléculaire de chaque film. Aucune phase similaire (à la phase couche mince) n’a, par contre, été détectée à leur interface air/composé. Deux températures d’isotropisation ont donc été observées à 106°C pour la phase couche mince et à 90°C pour la phase en volume.<p>Enfin, le phénomène de pré-transition de phase à l’interface air/composé de films épais de dihexylterthiophène et de dioctylterthiophène, a été étudié par ellipsométrie. Cette technique nous a permis d’observer la formation progressive d’une couche anisotrope à l’interface air/composé de chaque film quelques degrés au dessus de leur température de transition de phase isotrope/smectique. L’épaisseur de chaque couche anisotrope augmente par couche smectique lorsque la température décroit vers la température de transition de phase isotrope/smectique. À l’approche de cette température de transition, nous avons constaté que chaque épaisseur diverge impliquant un mouillage complet de leur interface air/composé. L’épaisseur de chaque couche anisotrope augmente tout d’abord de manière logarithmique ;puis à l’approche de la température de transition, cette augmentation suit une loi de puissance. <p> / Doctorat en Sciences / info:eu-repo/semantics/nonPublished

La structure chimique des semiconducteurs organiques utilisés dans les cellules photovoltaïques à base d’hétérojonction en volume peut fortement influencer les performances du dispositif final. Pour cette raison, une meilleure compréhension des relations structure-propriétés demeure cruciale pour l’amélioration des performances. Dans ce contexte, cette thèse fait état d'études approfondies du transport des charges, de la morphologie et des propriétés photovoltaïques sur de nouveaux copolymères à faible bande interdite. En premier lieu, l'impact de la position des chaînes alkyles sur les propriétés opto-électroniques et morphologiques a été étudié sur une famille de polymères. Les mesures du transport de charges ont montré que la planéité du squelette du copolymère influe sur l’évolution de la mobilité des charges avec la concentration de porteurs libres. Ce comportement suggère que le désordre énergétique électronique est fortement impacté par les angles de torsion intramoléculaire le long de la chaîne conjuguée. Un second copolymère à base d'unités accepteur de [2,1,3] thiadiazole pyridique, dont les niveaux d’énergie des orbitales frontières sont optimales pour l’application photovoltaïque, a ensuite été étudié. Les performances obtenues en cellule photovoltaïque sont très inférieures aux attentes. Des analyses de la morphologie et du transport de charge ont révélé que l’orientation des lamelles cristallines est défavorable au transport perpendiculaire au film organique et empêche ainsi une bonne extraction des charges photo-générées. Enfin, les propriétés opto-électroniques et photovoltaïques de copolymères fluorés ont été étudiées. Dans ce cas, les atomes de fluor favorisent la formation de lamelles orientées favorablement pour le transport. Ces bonnes propriétés nous ont permis d'atteindre un rendement de conversion de puissance de 9,8% avec une simple hétérojonction polymère:fullerène. / The chemical structure of organic semiconductors that are utilized in bulk heterojunction photovoltaic cells may strongly influence the final device performances. Thus, better understanding the structure-property relationships still remains a major task towards high efficiency. Within this framework, this thesis reports in-depth material investigations including charge transport, morphology and photovoltaic studies on various novel low band-gap copolymers. First, the impact of alkyl side chains on the opto-electronic and morphological properties has been studied on a series of polymers. Detailed charge transport investigations showed that a planar conjugated polymer backbone leads to a weak dependence of the charge carrier mobility on the carrier concentration. This observation points out that the intra-molecular torsion angle contributes significantly to the electronic energy disorder. Solar cells using another novel copolymer based on pyridal[2,1,3]thiadiazole acceptor unit have been studied in detail next. Despite the almost ideal frontier molecular orbital energy levels, this copolymer did not perform in solar cells as good as expected. A combined investigation of the thin film microstructure and transport properties showed that the polymers self-assemble into a lamellar structure with polymer chains being oriented preferentially “edge-on”, thus hindering the out-of-plane hole transport and leading to poor charge extraction. Finally, the impact of fluorine atoms in fluorinated polymers on the opto-electronic and photovoltaic properties has been investigated. In this case, the presence of both flat-lying and standing lamellae enabled efficient charge transport in all three directions. As a consequence, good charge extraction was possible and allowed us to achieve a maximum power conversion efficiency of 9.8%.

Il est reconnu que la structure des semi-conducteurs organiques influence la sensibilité et la sensitivité des capteurs des gaz. Pour améliorer la compréhension des mécanismes sous-jacents dans les capteurs à base des transistors d’effet de champ organique (OFETs) cette thèse a exploré trois pistes différentes : L’utilisation de l’hystérésis des caractéristiques de transfert comme paramètre de détection des gaz est étudié. En ajoutant l’hystérésis aux paramètres standards, on améliore la sélectivité des OFETs à base de poly(3-hexylthiophène) aux gaz polaires. Des mesures transitoires de courant indiquent que la cinétique de piégeage et de piégeage des porteurs de charges est à l’origine de cette amélioration. Pour comprendre l’influence qu’à la structure moléculaire sur la sensibilité aux vapeurs d’éthanol, des polymères avec des chaînes latérales alcoxyle dont on fait varier la polarité ainsi que l’encombrement stérique, ont été étudiés. L’intensité de la réponse est corrélée avec la quantité d’analyte absorbée et le moment dipolaire des chaînes latérales. Pour permettre l’étude des mécanismes à l’échelle nanométrique, une partie de ce travail se concentre sur la fabrication de transistors avec une taille de canal réduite. En utilisant le nitrure de silicium comme couche diélectrique, on réduite les tensions de commande et les propriétés chimiques à l’interface. / The molecular structure of organic semiconductors which can be tailored by the chemical synthesis influences the sensitivity and selectivity of gas sensor devices. To improve the understanding of the ongoing mechanisms in sensors based on organic field effect transistors (OFETs) this thesis follows three different tracks: The applicability of the hysteresis of the transfer characteristics as a gas sensing parameter is studied. As a complement to the standard transistor parameters the hysteresis improves the selectivity of poly(3-hexylthiophen-2,5-diyl) based OFETs to polar gases. Transient current measurements indicate the additional dependence on the detrapping kinetics as origin of the increased selectivity. To understand the influence of the molecular structure on the gas sensing behavior, polymers with alkoxy side chains, varying in polarity and steric hindrance, are used as gas sensing layer for ethanol vapor. The response strength correlates with the amount of absorbed analyte and the dipole moment of the side chains. To enable investigations of the mechanisms at the nanoscale, one part of this work focuses on the preparation of transistors with a reduced channel length. By using silicon nitride as dielectric layer, driving voltages decreased and interface properties could be improved.

For the past 40 years, relentless focus on Moore’s Law transistor scaling has provided ever-increasing transistor performance and density. In order to continue the technology scaling beyond 22nm node, it is clear that conventional bulk-MOSFET needs to be replaced by new device architectures, most promising being the Multiple-Gate MOSFETs (MuGFET). Intel in mid 2011 announced the use of bulk Tri-Gate FinFETs in 22nm high volume logic process for its next-gen IvyBridge Microprocessor. It is expected that soon other semiconductor companies will also adopt the MuGFET devices. As like bulk-MOSFET, an accurate and physical compact model is important for MuGFET based circuit design. Compact modeling effort for MuGFET started in late nineties with planar double gate MOSFET(DGFET),as it is the simplest structure that one can conceive for MuGFET devices. The models so far proposed for DG MOSFETs are applicable for common gate symmetric DG (SDG) MOSFETs where both the gates have equal oxide thicknesses. However, for practical devices at nanoscale regime, there will always be some amount of asymmetry between the gate oxide thicknesses due to process variations and uncertainties, which can affect device performance significantly. At the same time, Independently controlled DG(IDG) MOSFETs have gained tremendous attention owing to its ability to modulate threshold voltage and transconductance dynamically. Due to the asymmetric nature of the electrostatic, developing efficient compact models for asymmetric/independent DG MOSFET is a daunting task. In this thesis effort has been put to provide some solutions to this challenge. We propose simple surface-potential based compact terminal charge models, applicable for Asymmetric Double gate MOSFETs (ADG) in two configurations1) Common-gate 2) Independent-gate. The charge model proposed for the common-gate ADG (CDG) MOSFET is seamless between the symmetric and asymmetric devices and utilizes the unique so-far-unexplored quasi-linear relationship between the surface potentials along the channel. In this model, the terminal charges could be computed by basic arithmetic operations from the surface potentials and applied biases, and can be easily implemented in any circuit simulator and extendable to short-channel devices. The charge model proposed for independent ADG(IDG)MOSFET is based on a novel piecewise linearization technique of surface potential along the channel. We show that the conventional “charge linearization techniques that have been used over the years in advanced compact models for bulk and double-gate(DG) MOSFETs are accurate only when the channel is fully hyperbolic in nature or the effective gate voltages are same. For other bias conditions, it leads to significant error in terminal charge computation. We demonstrate that the amount of nonlinearity that prevails between the surface potentials along the channel for a particular bias condition actually dictates if the conventional charge linearization technique could be applied or not. We propose a piecewise linearization technique that segments the channel into multiple sections where in each section, the assumption of quasi-linear relationship between the surface potentials remains valid. The cumulative sum of the terminal charges obtained for each of these channel sections yield terminal charges of the IDG device. We next present our work on modeling the non-ideal scenarios like presence of body doping in CDG devices and the non-planar devices like Tri-gate FinFETs. For a fully depleted channel, a simple technique to include body doping term in our charge model for CDG devices, using a perturbation on the effective gate voltage and correction to the coupling factor, is proposed. We present our study on the possibility of mapping a non-planar Tri-gate FinFET onto a planar DG model. In this framework, we demonstrate that, except for the case of large or tall devices, the generic mapping parameters become bias-dependent and an accurate bias-independent model valid for geometries is not possible. An efficient and robust “Root Bracketing Method” based algorithm for computation of surface potential in IDG MOSFET, where the conventional Newton-Raphson based techniques are inefficient due to the presence of singularity and discontinuity in input voltage equations, is presented. In case of small asymmetry for a CDG devices, a simple physics based perturbation technique to compute the surface potential with computational complexity of the same order of an SDG device is presented next. All the models proposed show excellent agreement with numerical and Technology Computer-Aided Design(TCAD) simulations for all wide range of bias conditions and geometries. The models are implemented in a professional circuit simulator through Verilog-A, and simulation examples for different circuits verify good model convergence.

The present thesis is focused on rational design and synthesis of π-conjugated donor-acceptor (D-A) type oligomers and polymers. It is organized in six different chapters and a brief discussion on the content of the individual chapter is provided below. Chapter 1 briefly describes the charge transport properties of organic semiconductors followed by recent development of different organic semiconducting materials mainly for applications in OFET and solar cells have been highlighted. Chapter 2 explores the synthesis and characterization of two new liquid crystalline, D-A type bithiophene-benzothiazole derivatives. The liquid crystalline properties of the materials have been studied in detail with optical polarizing microscopic images and differential scanning calorimetry and found that these materials possess highly ordered smectic A liquid crystalline phase. Their charge transport properties have also been investigated by fabricating OFET devices. Chapter 3 describes the photophysical properties and OFET performance of quinoxaline based donors-acceptor-donor (D-A-D) type molecules. Depending on the flexibility and rigidity of the conjugated backbone these materials show liquid crystalline behaviour. Investigation of their OFET performance indicated that these molecules exhibit p-type mobility up to 9.7 x 10-4 cm2V-1s-1 and on/ off ratio of 104. Chapter 4 investigates excited state properties and OFET behavior of D-A-D type diketopyrrolopyrrole (DPP) derivatives end-capped with alkoxynaphthalene group. UV-Visible spectroscopy measurement shows strong intramolecular charge transfer (ICT) between donor and acceptor unit. Steady-state and time-resolved fluorescence measurements confirm the formation of excimer. The excited state interactions, the interchromophore separation and geometry of the molecules influence the extent of excimer formation. Finally, the OFET behavior of these DPP based materials has been studied using different dielectric layers. Chapter 5 discusses the synthesis, characterization and properties of two new thieno[3,2-b]thiophene-DPP based donor-acceptor (D-A) type low band gap polymers (PTTDPP-BDT and PTTDPP-BZT). Investigation of OFET performance indicated that polymers exhibited ambipolar behaviour with hole mobility upto 1.0 x 10-3 cm2/Vs and electron mobility upto 8 x 10-5 cm2/Vs. Using polymer PTTDPP-BDT with electron acceptor C70PCBM, power conversion efficiency (PCE) around 3.26% in bulk heterojunction solar cell has been achieved. Chapter 6 describes the approach to tailor the energy levels of conjugated polymers (PTDPP-IDT and PTTDPP-IDT) based on Indacenodithiophene (IDT) coupled with DPP moieties. We have studied the photovoltaic performance of these conjugated polymers by blending with PCBM and P3HT. The importance of these materials in polymer/polymer blend solar cell has been emphasized. The photovoltaic devices with polymer/polymer blend solar cell exhibit high open-circuit voltages (VOC) of ~ 0.8 V. In summary, the work presented in this thesis describes synthesis, characterization and photophysical properties of new organic semiconductors and their importance in optoelectronic devices. This work also describes a general design principle of nonfullerene organic solar cell. The results described here show that these materials have potential application as active components in plastic electronics.