No description available.

Im Gegensatz zu herkömmlichen Dehnungsmessstreifen können Carbon nanotube (CNT)-basierte Komposite zusätzlich eine ausgeprägte Druck-abhängigkeit des Widerstandes aufweisen. Deshalb können Drucksensoren aus CNT-Nanokomposite ohne den Einsatz von Verformungskörpern wie z. B. Biegebalken aufgebaut werden. Die möglichen Anwendungsgebiete für diese direkt messenden Sensoren wurden in der vorliegenden Arbeit bei drei industriellen Anwendungen wie z. B. bei Robotergreifarmen gezeigt. Die Zielstellung dieser Arbeit ist die Entwicklung und Charakterisierung eines neuartigen Sensors aus CNT-Nanokomposite. Unter Verwendung von Multi-walled carbon nanotube (MWCNT)-Epoxidharz und interdigitalen Elektroden soll der Sensor auf wenigen Quadratzentimetern Drücke im Megapascal-Bereich und somit Kräfte im Kilonewton-Bereich messen können. Durch die Auswahl geeigneter Werkstoffe und die Modellierung mit der Finite Element Methode wurde der Sensorentwurf durchgeführt sowie der Messbereich abgeschätzt. Die Herstellung der MWCNT-Epoxidharz-Dispersion erfolgte durch mechanische Mischverfahren. Anschließend wurden aus der Dispersion druckempfindliche Schichten mit der Schablonendrucktechnik hergestellt. Dabei wurden die Herstellungs-parameter und besonders der Füllstoffgehalt der MWCNTs variiert, um deren Einflüsse auf das mechanische, thermische und elektrische Verhalten zu untersuchen. Die Charakterisierung der mechanischen Kenngrößen erfolgte mit Zugversuchen und dynamisch-mechanischer Analyse. In den Untersuchungen zeigen die MWCNT-Komposite eine signifikante Steigerung der Zugfestigkeit und eine Erhöhung der Glasübergangstemperatur gegenüber reinem Epoxidharz. Die Abhängigkeiten der Druckempfindlichkeit und der Temperaturempfindlichkeit vom Füllstoffgehalt wurden untersucht. Eine besonders hohe Druckempfindlichkeit, aber auch Temperaturempfind-lichkeit wurde bei Proben mit geringem Füllstoffgehalt (1 wt% und 1,25 wt%) festgestellt. Es ist also wichtig, die richtige Materialkombination für diese Art Sensor zu finden. Die realisierten Sensoren liefern zuverlässige Antwortsignale bei wiederholten Belastungen bis zu einer Belastung von 20 MPa (entspricht 2 kN). Zusätzlich wurde der Temperatureinfluss in einem Bereich von −20 °C bis 50 °C durch eine Wheatstonesche Brückenschaltung kompensiert. Die vorliegende Arbeit zeigt, dass eine zuverlässige Druckmessung mit einer Temperaturmessabweichung von 0,214 MPa/10 K gewährleistet werden kann. / In contrast to conventional metallic strain gauges, carbon nanotube (CNT) composites have an additional pressure sensitivity. Therefore, deformation elements such as bending beam is not needed by using pressure sensors, which are based on CNT nanocomposite. The possible areas of application for these pressure direct measured sensors were showed in three industrial application such as robot gripper. The focus of this work is the development and characterization of a new sensor manufactured from CNT nanocomposite. By using multi-walled carbon nanotube (MWCNT) epoxy and interdigital electrodes the sensor, which has a dimension of few square centimetre, should measure a pressure in mega Pascal range and hence a force in kilo newton range. By the selection of suitable materials and the modelling using finite element method, the sensor design as well as the measurement range were carried out. The MWCNT epoxy dispersion is manufactured by using a mechanical mixing process. Subsequent, the dispersion is used to fabricate pressure sensitive layers by stencil printing methods. Thereby, the fabrication parameters and especially the filler content of the MWCNTs were varied for the mechanical, thermal and electrical investigation. The characterization of the mechanical characteristic values were carried out by using tensile test and dynamic mechanical analysis. The results show a significant increasing of the tensile strength and glass transition temperature in comparison to neat epoxy. Additionally, the influence of the filler content to the pressure and thermal sensitivity were investigated. A highly pressure sensitivity but also a highly thermal sensitivity are obtained for samples with lower filler contents (1 wt% and 1.25 wt%). Therefore, a suitable material combination has to be chosen. The fabricated sensors show reliable response signals by repeated excitations up to 20 MPa (meets to 2 KN). Moreover, the temperature influence ranged from -20 °C to 50 °C was compensated with a Wheatstone bridge. This work demonstrate a direct pressure sensitive sensor with reliable response signals by a thermal deviation of 0.214 MPa/10K.

<p>The aim of this thesis is to interconnect human tactile perception with various physical properties of materials. Tactile perception necessitates contact and relative motion between the skin and the surfaces of interest. This implies that properties such as friction and surface roughness ought to be important physical properties for tactile sensing. In this work, a method to measure friction between human fingers and surfaces is presented. This method is believed to best represent friction in tactile perception.</p><p>This study is focused on the tactile perception of printing papers. However, the methodology of finger friction measurements, as well as the methodology to link physical properties with human perception data, can be applied to almost whichever material or surfaces.</p><p> </p><p>This thesis is based on three articles.</p><p> </p><p>In Article I, one participant performed finger friction measurements, using a piezoelectric force sensor, on 21 printing papers of different paper grades and grammage (weight of the papers). Friction coefficients were calculated as the ratio of the frictional force and the normal force, shown to have a linear relationship. The values were recorded while stroking the index finger over the surface. The results show that measurements with the device can be used to discriminate a set of similar surfaces in terms of finger friction. When comparing the friction coefficients, the papers group according to paper surface treatment and an emerging trend is that the rougher (uncoated) papers have a lower friction coefficient than the smoother (coated) papers. In the latter case, this is interpreted in terms of a larger contact between the finger and paper surface.</p><p> </p><p>In addition, a decrease in friction coefficient is noted for all papers on repeated stroking, where the coated papers display a larger decrease. XPS (X-ray Photoelectron Spectroscopy) reveals that skin lipids are transferred from the finger to the paper surface, acting as a lubricant and hence decrease friction. Nevertheless, there is evidence that mechanical changes of the surface cannot be completely ruled out.</p><p> </p><p>The reproducibility of the finger friction measurements is elaborated in Article II, by using many participants on a selection of eight printing papers out of the 21. The trends in friction are the same; once again, the coated papers display the highest friction. There are notably large variations in the exact value of the friction coefficient, which are tentatively attributed to different skin hydration and stroking modes.</p><p> </p><p>These same participants also took part in a tactile study of perceived paper coarseness (“strävhet” in Swedish). The results reveal that the participants can distinguish a set of printing papers in terms of perceived coarseness. Not unexpectedly, surface roughness appears to be an important property related to perceived coarseness, where group data display that perceived coarseness increases with increasing surface roughness. Interestingly, friction also appears to be a discriminatory property for some subjects. A few participants showed opposite trends, which is evidence for that what is considered coarse is subjective and that different participants “weigh” the importance of the properties differently. This is a good example of a challenge when measuring one-dimensional perceptions in psychophysics.</p><p> </p><p>In Article III, a multidimensional approach was used to explore the tactile perception of printing papers. To do this, the participants scaled similarity among all possible pairs of the papers, and this similarity data are best presented by a three-dimensional space solution. This means that there are three underlying dimensions or properties that the participants use to discriminate the surface feel. Also, there is a distinct perceptual difference between the rougher (uncoated) and smoother (coated) papers. The surface roughness appears to be the dominant physical property when discriminating between a real rough paper and a smooth paper, whereas friction, thermal conductivity and grammage are more important when discriminating among the smooth coated papers.</p>

Un microscope à force atomique (AFM) est utilisé pour caractériser des matériaux isolant ou semi-conducteur avec une résolution pouvant atteindre l'échelle atomique. Ce microscope est constitué d'un capteur de force couplé à une électronique de contrôle pour pouvoir correctement caractériser ces matériaux. Parmi les différents modes (statique et dynamique), nous nous focalisons essentiellement sur le mode dynamique et plus particulièrement sur le fonctionnement sans contact à modulation de fréquence (FM-AFM). Dans ce mode, le capteur de force est maintenu comme un oscillateur harmonique par le système d'asservissement. Le projet ANR Pnano2008 intitulé : ”Cantilevers en carbure de silicium à piézorésistivité métallique pour AFM dynamique à très haute fréquence" a pour objectif d'augmenter significativement les performances d'un FM-AFM en développant un nouveau capteur de force très haute fréquence. Le but est d'augmenter la sensibilité du capteur et de diminuer le temps nécessaire à l'obtention d'une image de la surface du matériau. Le système de contrôle associé doit être capable de détecter des variations de fréquence de 100mHz pour une fréquence de résonance de 50MHz. Etant donné que les systèmes présents dans l'état de l'art ne permettent pas d'atteindre ces performances, l'objectif de cette thèse fut de développer un nouveau système de contrôle. Celui-ci est entièrement numérique et il est implémenté sur une carte de prototypage basée sur un FPGA. Dans ce mémoire, nous présentons le fonctionnement global du système ainsi que ses caractéristiques principales. Elles portent sur la détection de l'écart de fréquence de résonance du capteur de force. / An atomic force microscope (AFM) is used to characterize insulating materials or semiconductors with a resolution up to the atomic length scale. The microscope includes a force sensor linked to a control electronic in order to properly characterize these materials. Among the various modes (static and dynamic), we focus mainly on the dynamic mode and especially on the frequency modulation mode (FM-AFM). In this mode, the force sensor is maintained as a harmonic oscillator by the servo system. The research project ANR Pnano2008 entitled: "metal piezoresistivity silicon carbide cantilever for very high frequency dynamic AFM" aims to significantly increase the performance of a FM-AFM by developing new very high frequency force sensors. The goal is to increase the sensitivity of the sensor and to decrease the time necessary to obtain topography images of the material. The control system of this new sensor must be able to detect frequency variations as small as 100mHz for cantilevers with resonance frequencies up to 50MHz. Since the state-of-the-art systems doe not present these performances, the objective of this thesis was to develop a new control system. It is fully digital and it is implemented on a FPGA based prototyping board. In this report, we present the system overall functioning and its main features which are related to the cantilever resonant frequency detection. This detection is managed by a phase locked loop (PLL) which is the key element of the system.

L’objectif de cette thèse est le développement d’un nouveau capteur de forcemulti-axes destiné à mesurer les composantes de friction impliquées dans lecontact doigt/objet lors la micromanipulation dextre. Des études théoriques etdes simulations par éléments finis ont conduit à la conception de ce capteurMEMS piézorésistif composé d’une plate-forme centrale munie d’une microbille,entourée d’une table compliante. D’après les résultats de simulations, ce capteur estcapable de mesurer indépendamment les forces normales et de frottement (couplageréciproque inférieure à 1%) avec une bonne sensibilité. Différents runs de fabricationnous ont permis d’obtenir des dispositifs exploitables. La structure mécanique de cescapteurs a été validée par la mesure des fréquences de résonance qui sont en accordavec les résultats de simulation. Des premiers résultats expérimentaux en termesde mesure de force ont ensuite été obtenus grâce au développement d’un banc detest (structure robotique, actionneurs, caméras, etc.). Nous nous sommes égalementintéressés à la problématique de l’étalonnage des capteurs de micro et nanoforceà l’aide de ressorts magnétiques reliés à des masses mesurables. Nous avons, danscette optique, mis au point une stratégie d’estimation et de compensation passivedes perturbations mécaniques en utilisant un principe différentiel. Cette approchea été appliquée à un capteur de nanoforce basé sur la lévitation diamagnétique et aabouti à des résultats prometteurs : une résolution inférieure au nanonewton a puêtre obtenue. / Sensor enabling to characterize the finger/object contact involved in dexterousmicromanipulation. Theoretical studies and finite elements simulations have lead tothe conception of this piezoresistive MEMS sensor composed of a central platformwith a micro-ball and surrounded by a compliant table. According to the simulationresults, this sensor is able to independently measure the normal and friction forces(crosstalk less than 1 %) with a good sensitivity. Several runs of fabrication allowedus to obtain usable devices. The mechanical structure of such sensors has beenvalidated by the measurement of resonance frequencies that are consistent with thesimulation results. The first experimental results in terms of force measurement werethen obtained through the development of a test bench (robotic structure, actuators,cameras, etc.). We were also interested in the problem of calibration of micro andnanoforce sensors using magnetic springs connected to measurable masses. In thiscontext, we developed an estimation strategy and a passive rejection of mechanicaldisturbances using a differential principle. This approach was applied to a nanoforcesensor based on the diamagnetic levitation and yielded promising results: a resolutionlower the nanonewton level could be obtained.

The aim of this thesis is to interconnect human tactile perception with various physical properties of materials. Tactile perception necessitates contact and relative motion between the skin and the surfaces of interest. This implies that properties such as friction and surface roughness ought to be important physical properties for tactile sensing. In this work, a method to measure friction between human fingers and surfaces is presented. This method is believed to best represent friction in tactile perception. This study is focused on the tactile perception of printing papers. However, the methodology of finger friction measurements, as well as the methodology to link physical properties with human perception data, can be applied to almost whichever material or surfaces.   This thesis is based on three articles.   In Article I, one participant performed finger friction measurements, using a piezoelectric force sensor, on 21 printing papers of different paper grades and grammage (weight of the papers). Friction coefficients were calculated as the ratio of the frictional force and the normal force, shown to have a linear relationship. The values were recorded while stroking the index finger over the surface. The results show that measurements with the device can be used to discriminate a set of similar surfaces in terms of finger friction. When comparing the friction coefficients, the papers group according to paper surface treatment and an emerging trend is that the rougher (uncoated) papers have a lower friction coefficient than the smoother (coated) papers. In the latter case, this is interpreted in terms of a larger contact between the finger and paper surface.   In addition, a decrease in friction coefficient is noted for all papers on repeated stroking, where the coated papers display a larger decrease. XPS (X-ray Photoelectron Spectroscopy) reveals that skin lipids are transferred from the finger to the paper surface, acting as a lubricant and hence decrease friction. Nevertheless, there is evidence that mechanical changes of the surface cannot be completely ruled out.   The reproducibility of the finger friction measurements is elaborated in Article II, by using many participants on a selection of eight printing papers out of the 21. The trends in friction are the same; once again, the coated papers display the highest friction. There are notably large variations in the exact value of the friction coefficient, which are tentatively attributed to different skin hydration and stroking modes.   These same participants also took part in a tactile study of perceived paper coarseness (“strävhet” in Swedish). The results reveal that the participants can distinguish a set of printing papers in terms of perceived coarseness. Not unexpectedly, surface roughness appears to be an important property related to perceived coarseness, where group data display that perceived coarseness increases with increasing surface roughness. Interestingly, friction also appears to be a discriminatory property for some subjects. A few participants showed opposite trends, which is evidence for that what is considered coarse is subjective and that different participants “weigh” the importance of the properties differently. This is a good example of a challenge when measuring one-dimensional perceptions in psychophysics.   In Article III, a multidimensional approach was used to explore the tactile perception of printing papers. To do this, the participants scaled similarity among all possible pairs of the papers, and this similarity data are best presented by a three-dimensional space solution. This means that there are three underlying dimensions or properties that the participants use to discriminate the surface feel. Also, there is a distinct perceptual difference between the rougher (uncoated) and smoother (coated) papers. The surface roughness appears to be the dominant physical property when discriminating between a real rough paper and a smooth paper, whereas friction, thermal conductivity and grammage are more important when discriminating among the smooth coated papers.

In this study, we propose a multi-walled carbon nanotube epoxy composite sensor for force and pressure sensing in the range of 50 N–2 kN. A manufacturing procedure, including material preparation and deposition techniques, is proposed. The electrode dimensions and the layer thickness were optimized by the finite element method. Temperature compensation is realized by four nanocomposites elements, where only two elements are exposed to the measurand. In order to investigate the influence of the filler contents, samples with different compositions were prepared and investigated. Additionally, the specimens are characterized by cyclical and stepped force/pressure loads or at defined temperatures. The results show that the choice of the filler content should meet a compromise between sensitivity, temperature influence and noise behavior. At constant temperature, a force of at least 50N can be resolved. The measurement error due to the temperature influence is 150N in a temperature range of –20°C–50°C.

Im Gegensatz zu herkömmlichen Dehnungsmessstreifen können Carbon nanotube (CNT)-basierte Komposite zusätzlich eine ausgeprägte Druck-abhängigkeit des Widerstandes aufweisen. Deshalb können Drucksensoren aus CNT-Nanokomposite ohne den Einsatz von Verformungskörpern wie z. B. Biegebalken aufgebaut werden. Die möglichen Anwendungsgebiete für diese direkt messenden Sensoren wurden in der vorliegenden Arbeit bei drei industriellen Anwendungen wie z. B. bei Robotergreifarmen gezeigt. Die Zielstellung dieser Arbeit ist die Entwicklung und Charakterisierung eines neuartigen Sensors aus CNT-Nanokomposite. Unter Verwendung von Multi-walled carbon nanotube (MWCNT)-Epoxidharz und interdigitalen Elektroden soll der Sensor auf wenigen Quadratzentimetern Drücke im Megapascal-Bereich und somit Kräfte im Kilonewton-Bereich messen können. Durch die Auswahl geeigneter Werkstoffe und die Modellierung mit der Finite Element Methode wurde der Sensorentwurf durchgeführt sowie der Messbereich abgeschätzt. Die Herstellung der MWCNT-Epoxidharz-Dispersion erfolgte durch mechanische Mischverfahren. Anschließend wurden aus der Dispersion druckempfindliche Schichten mit der Schablonendrucktechnik hergestellt. Dabei wurden die Herstellungs-parameter und besonders der Füllstoffgehalt der MWCNTs variiert, um deren Einflüsse auf das mechanische, thermische und elektrische Verhalten zu untersuchen. Die Charakterisierung der mechanischen Kenngrößen erfolgte mit Zugversuchen und dynamisch-mechanischer Analyse. In den Untersuchungen zeigen die MWCNT-Komposite eine signifikante Steigerung der Zugfestigkeit und eine Erhöhung der Glasübergangstemperatur gegenüber reinem Epoxidharz. Die Abhängigkeiten der Druckempfindlichkeit und der Temperaturempfindlichkeit vom Füllstoffgehalt wurden untersucht. Eine besonders hohe Druckempfindlichkeit, aber auch Temperaturempfind-lichkeit wurde bei Proben mit geringem Füllstoffgehalt (1 wt% und 1,25 wt%) festgestellt. Es ist also wichtig, die richtige Materialkombination für diese Art Sensor zu finden. Die realisierten Sensoren liefern zuverlässige Antwortsignale bei wiederholten Belastungen bis zu einer Belastung von 20 MPa (entspricht 2 kN). Zusätzlich wurde der Temperatureinfluss in einem Bereich von −20 °C bis 50 °C durch eine Wheatstonesche Brückenschaltung kompensiert. Die vorliegende Arbeit zeigt, dass eine zuverlässige Druckmessung mit einer Temperaturmessabweichung von 0,214 MPa/10 K gewährleistet werden kann. / In contrast to conventional metallic strain gauges, carbon nanotube (CNT) composites have an additional pressure sensitivity. Therefore, deformation elements such as bending beam is not needed by using pressure sensors, which are based on CNT nanocomposite. The possible areas of application for these pressure direct measured sensors were showed in three industrial application such as robot gripper. The focus of this work is the development and characterization of a new sensor manufactured from CNT nanocomposite. By using multi-walled carbon nanotube (MWCNT) epoxy and interdigital electrodes the sensor, which has a dimension of few square centimetre, should measure a pressure in mega Pascal range and hence a force in kilo newton range. By the selection of suitable materials and the modelling using finite element method, the sensor design as well as the measurement range were carried out. The MWCNT epoxy dispersion is manufactured by using a mechanical mixing process. Subsequent, the dispersion is used to fabricate pressure sensitive layers by stencil printing methods. Thereby, the fabrication parameters and especially the filler content of the MWCNTs were varied for the mechanical, thermal and electrical investigation. The characterization of the mechanical characteristic values were carried out by using tensile test and dynamic mechanical analysis. The results show a significant increasing of the tensile strength and glass transition temperature in comparison to neat epoxy. Additionally, the influence of the filler content to the pressure and thermal sensitivity were investigated. A highly pressure sensitivity but also a highly thermal sensitivity are obtained for samples with lower filler contents (1 wt% and 1.25 wt%). Therefore, a suitable material combination has to be chosen. The fabricated sensors show reliable response signals by repeated excitations up to 20 MPa (meets to 2 KN). Moreover, the temperature influence ranged from -20 °C to 50 °C was compensated with a Wheatstone bridge. This work demonstrate a direct pressure sensitive sensor with reliable response signals by a thermal deviation of 0.214 MPa/10K.

Tactile perception is considered an important contributor to the overall consumer experience of a product. However, what physical properties that create the specifics of tactile perception, are still not completely understood. This thesis has researched how many dimensions that are required to differentiate the surfaces perceptually, and then tried to explain these dimensions in terms of physical properties, by interconnecting human perception measurements with various physical measurements. The tactile perception was assessed by multidimensional scaling or magnitude estimation, in which methods human participants assign numbers to how similar pairs of surfaces are perceived or to the relative quantity of a specified perceptual attribute, such as softness, smoothness, coarseness and coolness. The role of friction and surface texture in tactile perception was investigated in particular detail, because typically tactile exploration involves moving (at least) one finger over a textured surface. A tactile approach for measuring friction was developed by means of moving a finger over the surfaces, mounted on a force sensor. The contribution of finger friction to tactile perception was investigated for surfaces of printing papers and tissue papers, as well as for model surfaces with controlled topography. The overarching research goal of this thesis was to study, systematically, the role of texture in tactile perception of surfaces. The model surfaces displayed a sinusoidal texture with a characteristic wavelength and amplitude, fabricated by surface wrinkling and replica molding techniques. A library of surfaces was manufactured, ranging in wavelengths from 270 nm up to 100 µm and in amplitudes from 7 nm up to 6 µm. These surfaces were rigid and cleanable and could therefore be reused among the participants. To my knowledge, this is the first time in a psychophysical experiment, that the surface texture has been controlled over several orders of magnitude in length scale, without simultaneously changing other material properties of the stimuli. The finger friction coefficient was found to decrease with increasing aspect ratio (amplitude/wavelength) of the model surfaces and also with increasing average surface roughness of the printing papers. Analytical modeling of the finger’s interaction with the model surfaces shows how the friction coefficient increases with the real contact area, and that the friction mechanism is the same on both the nanoscale and microscale. The same interaction mechanism also explains the friction characteristics of tissue paper. Furthermore, it was found that the perceptions of smoothness, coarseness, coolness and dryness are satisfactorily related to the real contact area at the finger-surface interface.  It is shown that it is possible to discern perceptually among both printing papers and tissue papers, and this differentiation is based on either two or three underlying dimensions. Rough/smooth and thin/thick were the two main dimensions of surface feel found for the printing papers, whereas friction and wavelength were strongly related to the perceptual cues employed in scaling the model surfaces. These experimental results support the duplex theory of texture perception, which holds that both a “spatial sense”; used to discriminate the roughest textures from the others, and a “vibration sense”; used to discriminate among the smoother textures, are involved. The perception of what is considered rough and smooth depends on the experimental stimulus context. It is concluded that friction is important for human differentiation of surface textures below about 10 µm in surface roughness, and for larger surface textures, friction is less important or can even be neglected. The finger friction experiments also allowed the following conclusions to be drawn: (i) The interindividual variation in friction coefficients is too large to allow direct comparison; however, the trends in relative friction coefficients for a group of participants are the same. (ii) Lipids are transferred to the test surface of study, and this lowers the friction. (iii) Many of the studies point to a characteristic frequency during sliding of about 30 Hz, which is both characteristic of the resonance frequency of skin and the expected frequency associated with the fingerprints. (iv) The applied load in surface interrogation is in fact regulated in response to the friction force. The limits in tactile perception were indirectly researched by similarity scaling experiments on the model surfaces. Wrinkle wavelengths of 760 nm and 870 nm could be discriminated from untextured reference surfaces, whereas 270 nm could not. The amplitude of the wrinkles so discriminated was approximately 10 nm, suggesting that nanotechnology may well have a role to play in haptics and tactile perception. / Taktil perception bidrar starkt till den sammantagna upplevelsen av en produkt, men hur materials olika ytegenskaper påverkar och styr perceptionen är ännu inte helt klart. Den här avhandlingen undersöker hur många och vilka egenskaper som är viktiga när känslan mellan två ytor jämförs. Tillvägagångssättet är tvärvetenskapligt där fysikaliska mätningar kopplas ihop med perceptions mätningar där människor används som instrument. Två typer av perceptionsförsök har utförts, multidimensionell skalning där försökspersoner sätter siffror på hur lika två ytor känns, samt magnitud estimation där i stället intensiteten på specifika perceptuella storheter som t.ex. upplevt lenhet, upplevd mjukhet och upplevd strävhet bedömdes. Eftersom taktil perception innebär kontakt samt relativ rörelse mellan hud och ytor, har fokus i avhandlingen varit att undersöka hur friktion och ytans struktur (ytråhet) påverkar och bidrar till den taktila perceptionen. Förutom fysikaliska mätningar på friktion och ytstruktur har värmekonduktivitet, mjukhet samt olika standard mätningar inom pappersindustrin mätts. En metod för att mäta friktion mellan ett finger och olika ytor har utvecklats för att i möjligaste mån återspegla friktionskomponenten i upplevt taktil perception. Friktionskoefficienter beräknades och jämfördes mellan alla ytor. De stimuli som har studerats är tryckpapper och mjukpapper samt modellytor, gjorda för att systematiskt undersöka hur ytstruktur påverkar perceptionen. Tillverkningsmetoden för modellytorna valdes så att ytorna var tåliga och kunde tvättas och därmed återanvändas. Strukturen på ytorna bestod av ett vågformat mönster där våglängden varierade mellan 270 nm och 100 µm och amplituden mellan 7 nm och 6 µm. Enligt vår vetskap är det första gången som strukturer i de här skalorna har gjorts utan att samtidigt ändra andra material egenskaper. Friktionskoefficienten minskade med ökad kvot mellan amplituden och våglängden på modellytorna samt med ytråheten på tryckpappren. En analytisk modell tillämpades på kontakten mellan ett finger och ytorna som visade att friktionskoefficienten beror av den verkliga kontaktarean. För de mycket grövre mjukpappren uppmättes inga stora skillnader i friktion förmodligen för att kontakarean mellan de olika mjukpapprena var lika. Den faktiska kontakarean visade sig också vara viktig för perceptionen av lenhet, strävhet, torrhet och svalhet. Det visade sig vara en stor perceptuell skillnad mellan olika typer av tryckpapper och mjukpapper utifrån hur stimuli placerade sig på en taktil karta. För de tre materialen användes enbart två alternativt tre egenskaper hos materialet för att särskilja mellan alla olika par. För tryckpapper verkade en viktig dimension kunna beskrivas av alla de perceptuella och fysikaliska egenskaper som har med kontaktarean att göra, d.v.s. lenhet, svalhet, torrhet, ytråhet, värmekonduktivitet samt friktion. För att taktilt särskilja mellan olika ytor där bara strukturen är varierade, kunde friktion och våglängden relateras till spridningen i kartan. Båda studierna stödjer duplex theory of texture perception, där ett spatialt sinne används för att särskilja en av de grövre ytorna från en slät, och ett vibrationssinne för att särskilja mellan olika släta strukturer. Friktionen visade sig alltså vara en viktig fysikalisk egenskap för strukturer under åtminstone 10 µm i ytråhet. Från fingerfriktions mätningar kunde även följande slutsatser dras: (i) Stora skillnader i friktionskoefficient mellan olika personer uppmättes, men trenderna mellan olika individer var samma, vilket gör att relativa skillnader i friktion från en individ är representativa. (ii) Lipider (fingerfett) som överförs från fingret till ytan vid kontakt sänker friktionen. (iii) Frekvensinnehållet i friktionskraften varierar mellan olika ytor och den frekvenstopp som ses vid 30 Hz kan möjligtvis bero på fingrets struktur eller resonansfrekvensen på huden. (iv) Den pålagda kraften under en friktionsmätning visar sig omedvetet regleras av den friktionskraft som fingret möter under rörelse.  Hur små strukturer som kan diskrimineras har indirekt undersökts genom likhetsförsöket på modellytorna där försökspersoner skulle bedöma hur lika alla par av ytor kändes. Resultaten visade att ytorna med våglängder på 760 nm och 870 nm upplevdes olika jämfört med referens ytor utan något systematiskt mönster, medan ytan med 270 nm i våglängd inte kunde särskiljas. Amplituden på ytan som kunde diskrimineras var endast ca 10 nm, vilket indikerar att nanoteknologi mycket väl kan bidra inom haptiken och för att i framtiden kontrollera den taktila perceptionen. / <p>QC 20121026</p>